RBP or route by ports can help in translating the DMA
address over the PCI. Thus adding the RBP support with
long and short formats
Signed-off-by: Minghuan Lian <minghuan.lian@nxp.com>
Signed-off-by: Sachin Saxena <sachin.saxena@nxp.com>
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch adds the logic in the DPAA2 QDMA packet enqueue API
Fixes: 4d9a3f2a01 ("raw/dpaa2_qdma: support RBP mode")
Cc: stable@dpdk.org
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The rawdev xstats_reset function is now enabled. It is called when the
ioat autotest completes, to reset all xstat values after they have been
modified during testing.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Bruce Richardson <bruce.richardson@intel.com>
When running the ioat_rawdev_autotest, the ring size was initially required
to be 0. This prevented the test being run multiple times, as the ring size
is modified to a non-zero value when running the first test.
A global variable is now used to track the expected ring size, and is used
in the initial value check. This enables the test to be run more than
once.
Fixes: 849470d522 ("raw/ioat: add configure, start and stop functions")
Cc: stable@dpdk.org
Reported-by: Yinan Wang <yinan.wang@intel.com>
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The ioat rawdev was initially started during the test, however was never
stopped. This would cause issues when running the test again, as the device
cannot be configured when in a running state.
The device is now stopped after the test has completed, or if the test is
terminated due to error.
Fixes: 849470d522 ("raw/ioat: add configure, start and stop functions")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
This code is being shared by more than 1 type of driver.
Common is most appropriate place for it.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The warning disable flags for the base driver code were copy-pasted from
another source, and are actually unnecessary for this driver. Therefore
remove them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Introduce enqueue and dequeue functions to support packet based
processing. And enable write-combining for ntb driver since it
can improve the performance a lot.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add xstats support for NTB rawdev.
Support tx-packets, tx-bytes, tx-errors and
rx-packets, rx-bytes, rx-missed.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Setup and init NTB txq and rxq. And negotiate queue information
with the peer. If queue size and number of queues are not
consistent on both sides, return error.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Restrict this header inclusion to its real users.
Fixes: 028669bc9f ("eal: hide shared memory config")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Some drivers were missing reasons text for their disabling in meson.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Luca Boccassi <bluca@debian.org>
The driver names for rawdevs were both different in make and meson builds
and were non-standard in the make version in that some included "rawdev" in
the name while others didn't.
Therefore, for global consistency of naming, we can use "rte_rawdev" rather
than "rte_pmd" for the prefix for the libraries. While most other driver
categories use "rte_pmd" as a prefix, there is precedent for this in the
mempool drivers use "rte_mempool" as a prefix.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The ifpga and skeleton rawdev drivers included "rawdev" in their directory
names, which was superfluous given that they were in the drivers/raw
directory. Shorten the names via this patch.
For meson builds, this will rename the final library .so/.a files
produced, but those will be renamed again later via a patch to
standardize rawdev names.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some builds with clang report an error because '<>' rather than '""' were
used for including the ioat spec header file.
Target: x86_64-native-bsdapp-clang
error: 'rte_ioat_spec.h' file not found with <angled> include; use "quotes" instead
#include <rte_ioat_spec.h>
^~~~~~~~~~~~~~~~~
"rte_ioat_spec.h"
1 error generated.
Since this file should always be in the same directory as the main header,
we can safely change the include line to fix this error.
Fixes: abff4333ec ("raw/ioat: create device on probe and destroy on release")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The rte_vdev_driver is declared twice.
The first one is not necessary.
Fixes: 3298fa4853 ("raw/dpaa2_cmdif: introduce DPAA2 command interface driver")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The rte_vdev_driver is declared twice.
The first one is not necessary.
Fixes: 61c592a8d0 ("raw/skeleton: introduce skeleton rawdev driver")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
In order to align name with other PCI driver flag such as
RTE_PCI_DRV_NEED_MAPPING and to reflect its purpose, change
RTE_PCI_DRV_IOVA_AS_VA flag name as RTE_PCI_DRV_NEED_IOVA_AS_VA.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David Marchand <david.marchand@redhat.com>
The incriminated commit broke the use of RTE_PCI_DRV_IOVA_AS_VA which
was intended to mean "driver only supports VA" but had been understood
as "driver supports both PA and VA" by most net drivers and used to let
dpdk processes to run as non root (which do not have access to physical
addresses on recent kernels).
The check on physical addresses actually closed the gap for those
drivers. We don't need to mark them with RTE_PCI_DRV_IOVA_AS_VA and this
flag can retain its intended meaning.
Document explicitly its meaning.
We can check that a driver requirement wrt to IOVA mode is fulfilled
before trying to probe a device.
Finally, document the heuristic used to select the IOVA mode and hope
that we won't break it again.
Fixes: 703458e19c ("bus/pci: consider only usable devices for IOVA mode")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Jerin Jacob <jerinj@marvell.com>
Tested-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
When using _mm_set_epi64() rather than _mm_set_epi64x() intrinsic, ICC
tries to use the x87 floating point registers, leading to warnings about
not properly clearing value when switching between x87 and SSE/AVX modes.
error #13203: No EMMS instruction before call to function
Fix this by using the set64x() intrinsic.
Fixes: 0a92e63fc4 ("raw/ioat: add local API to perform copies")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Tested-by: Anatoly Burakov <anatoly.burakov@intel.com>
Enable an example for rawdev ntb. Support interactive mode to send
file on one host and receive file from another host. The command line
would be 'send [filepath]' and 'receive [filepath]'.
But since the FIFO is not enabled right now, use rte_memcpy as the enqueue
and dequeue functions and only support transmitting file no more than 4M.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Add handshake process using doorbell so that two hosts can
communicate to start and stop.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Add in the list of registers for the device.
And enable NTB device ops for Intel Skylake platform.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Introduce rawdev driver support for NTB (Non-transparent Bridge) which
can help to connect two separate hosts with each other.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Reviewed-by: Xiaolong Ye <xiaolong.ye@intel.com>
Sample test to verify DMA functionality, this test covers
internal transfer mode.
Signed-off-by: Satha Rao <skoteshwar@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Send message to PF to stop DMA queue when device close is
called from application.
Defined the required data structures to support enqueue and
dequeue APIs.
Signed-off-by: Satha Rao <skoteshwar@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Register dev_configure API to configure DPI PCI devices.
After successful initialization send message to PF to open
corresponding DPI DMA queue. At present hardware doesn't
support mail box for DPI, so PMD to PF communication uses
pre build kernel devfs.
Signed-off-by: Satha Rao <skoteshwar@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Add the make and meson based build infrastructure along
with the DMA device probe with documentation infrastructure.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Satha Rao <skoteshwar@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
cast unsigned int ports_per_retimer, unsigned int nums_retimer,
unsigned int nums_fvl and unsigned int ports_per_fvl to uint64_t
before multiply operation, to avoid Unintentional integer overflow.
Coverity issue: 337924, 337926
Fixes: d1cd4eb2d4 ("raw/ifpga: support ipn3ke")
Cc: stable@dpdk.org
Signed-off-by: Andy Pei <andy.pei@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Fix the readout retimer link status incorrectly when we
remove the linux intel-fpga-driver and run the DPDK application.
The linux driver will stop the retimer when remove the kernel
modules.
Fixes: 8a256bef ("raw/ifpga/base: add eth group driver")
Cc: stable@dpdk.org
Reported-by: Amrutha Sampath <amrutha.sampath@intel.com>
Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Add local APIs to trigger data copies, and retrieve handle values once
those copies are completed. Included are unit tests to validate the data
is copies correctly.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Add stats functions to track what is happening in the driver, and put
unit tests to check those.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Allow initializing a driver instance. Include selftest to validate these
functions.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Add in the "info_get" function to the driver, to allow us to query the
device. This allows us to have the unit test pick up the presence of
supported hardware or not.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Add the create/destroy driver functions so that we can actually allocate
a rawdev and destroy it when done. No rawdev API functions are actually
implemented at this point.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Add in the list of registers for the device. File is taken from the SPDK
project:
https://github.com/spdk/spdk/blob/master/include/spdk/ioat_spec.h
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Add stubs for ioat rawdev driver support in DPDK, specifically:
* makefile and meson build hooks
* initial public header file
* rawdev main C file, with probe and release functions
* release note update announcing the driver
* initial documentation for the new section in the rawdev doc
* unit test stubs for device unit tests
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
For each driver where we optionally disable it, add in the reason why it's
being disabled, so the user knows how to fix it.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
When running self-tests, the driver needs to know the device on which to
run the tests, so we need to take the device ID as parameter. Only the
skeleton driver is providing this selftest capability right now, so we can
easily update it for this change.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Use a variable value rather than compile-time constant zero as the
device id for the skeleton rawdev tests. This ensures we can make the
tests work even if other rawdevs are present.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
