RTE_FLOW API allows hardware parsing and steering of packets to specific
queues which helps in distributing ingress traffic across various cores.
Adding 'flow' rules allows user to specify the distribution required.
Signed-off-by: Anoob Joseph <anoobj@marvell.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
This patch updates the minimum driver version that supports
Intel QuickAssist device D15xx.
Signed-off-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Multi-segment mbufs are not supported for DOCSIS security protocol.
This patch adds an explicit check for this and returns an op error if
this case is found. This limitation is also added to the QAT cryptodev
documentation.
Fixes: 6f0ef237404b ("crypto/qat: support DOCSIS protocol")
Signed-off-by: David Coyle <david.coyle@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
The patch reverts the commit that updated Intel QuickAssist GEN3
marketing name. The change was not backported and has to be withdrawn.
This reverts commit 9cd9d3e702fba4700539c1a2eddac13dd14ecf70
Signed-off-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Add information about possible optimizations using C11 atomic builtins.
Signed-off-by: Phil Yang <phil.yang@arm.com>
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
This change is required to allow the branch ratio algorithm to
power manage cores with no workload running on them. This is
useful both when idle cores don't use C-states and for a number of
hyperthreading scenarios.
Signed-off-by: Rory Sexton <rory.sexton@intel.com>
Reviewed-by: David Hunt <david.hunt@intel.com>
Acked-by: Reshma Pattan <reshma.pattan@intel.com>
This modification allows for the branch ratio threshold to be set
per core rather than system wide. This gives greater flexibility to
the branch ratio monitoring allowing it to manage different
workloads with different characteristics on the same system.
Signed-off-by: Rory Sexton <rory.sexton@intel.com>
Reviewed-by: David Hunt <david.hunt@intel.com>
Acked-by: Reshma Pattan <reshma.pattan@intel.com>
Add a new item "rte_flow_item_ecpri" in order to match eCRPI header.
eCPRI is a packet based protocol used in the fronthaul interface of
5G networks. Header format definition could be found in the
specification via the link below:
https://www.gigalight.com/downloads/standards/ecpri-specification.pdf
eCPRI message can be over Ethernet layer (.1Q supported also) or over
UDP layer. Message header formats are the same in these two variants.
Signed-off-by: Bing Zhao <bingz@mellanox.com>
Acked-by: Ori Kam <orika@mellanox.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The new 5-tuple swap engine swaps:
source and destination mac address,
source and destination address in ipv4/ipv6,
source and destination port in UDP/TCP.
The forwarding engine will parse each layer
and swap it, and will stop when the next
layer doesn't match.
The mentioned headers of ICMP/ARP/Multicast
packets will be swapped as well according to
matching layers.
usage: --forward-mode=5tswap
Signed-off-by: Shiri Kuzin <shirik@mellanox.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This commit adds testpmd capability to provide timestamps on the packets
being sent in the txonly mode. This includes:
- SEND_ON_TIMESTAMP support
new device Tx offload capability support added, example:
testpmd> port config 0 tx_offload send_on_timestamp on
- set txtimes, registers field and flag, example:
testpmd> set txtimes 1000000,0
This command enables the packet send scheduling on timestamps if
the first parameter is not zero, generic format:
testpmd> set txtimes (inter),(intra)
where:
inter - is the delay between the bursts in the device clock units.
If "intra" (next parameter) is zero, this is the time between the
beginnings of the first packets in the neighbour bursts, if "intra"
is not zero, "inter" specifies the time between the beginning of
the first packet of the current burst and the beginning of the last
packet of the previous burst. If "inter"parameter is zero the send
scheduling on timestamps is disabled (default).
intra - is the delay between the packets within the burst specified
in the device clock units. The number of packets in the burst is
defined by regular burst setting. If "intra" parameter is zero no
timestamps provided in the packets excepting the first one in the
burst.
As the result the bursts of packet will be transmitted with
specific delay between the packets within the burst and specific
delay between the bursts. The rte_eth_read_clock() is supposed to
be engaged to get the current device clock value and provide the
reference for the timestamps. If there is no supported
rte_eth_read_clock() there will be no provided send scheduling on
the device.
- show txtimes, displays the timing settings
- txonly burst time pattern
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
There is the requirement on some networks for precise traffic timing
management. The ability to send (and, generally speaking, receive)
the packets at the very precisely specified moment of time provides
the opportunity to support the connections with Time Division
Multiplexing using the contemporary general purpose NIC without involving
an auxiliary hardware. For example, the supporting of O-RAN Fronthaul
interface is one of the promising features for potentially usage of the
precise time management for the egress packets.
The main objective of this patchset is to specify the way how applications
can provide the moment of time at what the packet transmission must be
started and to describe in preliminary the supporting this feature
from mlx5 PMD side [1].
The new dynamic timestamp field is proposed, it provides some timing
information, the units and time references (initial phase) are not
explicitly defined but are maintained always the same for a given port.
Some devices allow to query rte_eth_read_clock() that will return
the current device timestamp. The dynamic timestamp flag tells whether
the field contains actual timestamp value. For the packets being sent
this value can be used by PMD to schedule packet sending.
The device clock is opaque entity, the units and frequency are
vendor specific and might depend on hardware capabilities and
configurations. If might (or not) be synchronized with real time
via PTP, might (or not) be synchronous with CPU clock (for example
if NIC and CPU share the same clock source there might be no
any drift between the NIC and CPU clocks), etc.
After PKT_RX_TIMESTAMP flag and fixed timestamp field supposed
deprecation and obsoleting, these dynamic flag and field might be
used to manage the timestamps on receiving datapath as well. Having
the dedicated flags for Rx/Tx timestamps allows applications not
to perform explicit flags reset on forwarding and not to promote
received timestamps to the transmitting datapath by default.
The static PKT_RX_TIMESTAMP is considered as candidate to become
the dynamic flag and this move should be discussed.
When PMD sees the "rte_dynfield_timestamp" set on the packet being sent
it tries to synchronize the time of packet appearing on the wire with
the specified packet timestamp. If the specified one is in the past it
should be ignored, if one is in the distant future it should be capped
with some reasonable value (in range of seconds). These specific cases
("too late" and "distant future") can be optionally reported via
device xstats to assist applications to detect the time-related
problems.
There is no any packet reordering according timestamps is supposed,
neither within packet burst, nor between packets, it is an entirely
application responsibility to generate packets and its timestamps
in desired order. The timestamps can be put only in the first packet
in the burst providing the entire burst scheduling.
PMD reports the ability to synchronize packet sending on timestamp
with new offload flag:
This is palliative and might be replaced with new eth_dev API
about reporting/managing the supported dynamic flags and its related
features. This API would break ABI compatibility and can't be introduced
at the moment, so is postponed to 20.11.
For testing purposes it is proposed to update testpmd "txonly"
forwarding mode routine. With this update testpmd application generates
the packets and sets the dynamic timestamps according to specified time
pattern if it sees the "rte_dynfield_timestamp" is registered.
The new testpmd command is proposed to configure sending pattern:
set tx_times <burst_gap>,<intra_gap>
<intra_gap> - the delay between the packets within the burst
specified in the device clock units. The number
of packets in the burst is defined by txburst parameter
<burst_gap> - the delay between the bursts in the device clock units
As the result the bursts of packet will be transmitted with specific
delays between the packets within the burst and specific delay between
the bursts. The rte_eth_read_clock is supposed to be engaged to get the
current device clock value and provide the reference for the timestamps.
[1] http://patches.dpdk.org/patch/73714/
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Softnic can be used like other virtual devices without
needing any special mode. Therefore, remove softnic mode
from testpmd app. Documentation is updated as well.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
The APIs are marked in the doxygen comment but better to mark the
symbols too. This is planned for v20.11 release.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Flow manager API includes push/pop actions, so support corresponding
DPDK flow actions.
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
Add support for .get_reg eth_dev ops which will be used to collect the
firmware debug data.
PMD on detecting on some HW errors will collect the FW/HW Dump to a
buffer and then it will save it to a file implemented in
qede_save_fw_dump().
Dump file location and name:
Location: <RTE_SDK> or DPDK root
Name: qede_pmd_dump_mm-dd-yy_hh-mm-ss.bin
DPDK applications can initiate a debug data collection by invoking DPDK
library’s rte_eth_dev_get_reg_info() API. This API invokes .get_reg()
interface in the PMD.
PMD implementation of .get_reg() collects the FW/HW Dump, saves it to
data field of rte_dev_reg_info and passes it to the application. It’s
the responsibility of the application to save the FW/HW Dump to a file.
We recommendation using the file name format used by qede_save_fw_dump().
Signed-off-by: Rasesh Mody <rmody@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Added support for set ipv4 address action items. It allows the source
or destination ip address to be changed for a given flow.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for the vlan push and vlan pop actions
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add bnxt vector PMD support using NEON SIMD instructions.
Also update the 20.08 release notes with this information.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Dynamic flow used instead of layout defined.
The actual key/mask size depends on protocols and(or) fields
of patterns specified.
Also, the key and mask should start from the beginning of IOVA.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Enable/disable link state interrupt and get link state api is
defined using IOCTL calls from kernel driver
Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Minimize the number of different thread variables
Add all the thread specific variables in dpaa_portal
structure to optimize TLS Usage.
Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The patch adds support for portal migration by disabling stashing
for the portals which is used in the non-affined threads, or on
threads affined to multiple cores
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch enables flow query function to get the
configuration of the specified rule.
Signed-off-by: Chenxu Di <chenxux.di@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
The legacy filter API will be superseded by rte_flow.
There are also several small features which can not be
implemented in rte_flow. This patch re-implemented these
features as private API.
Two APIs are added:
rte_pmd_ixgbe_get_fdir_info.
rte_pmd_ixgbe_get_fdir_stats.
Signed-off-by: Chenxu Di <chenxux.di@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
The legacy filter API will be superseded by rte_flow.
There are also several small features which can not be
implemented in rte_flow. This patch re-implemented these
features as private API.
Three APIs are added:
rte_pmd_i40e_get_fdir_info.
rte_pmd_i40e_get_fdir_stats.
rte_pmd_i40e_set_gre_key_len.
Signed-off-by: Chenxu Di <chenxux.di@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
This patch enables cloud filter for IPv4/6_UDP/TCP/SCTP with
SRC port only or DST port only.
This supports different filter types for the same packet type.
E.g. one IPv4_UDP rules with SRC port only and another IPv4_UDP rule
with DST port only.
Signed-off-by: Guinan Sun <guinanx.sun@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Currently, the tbl8 group is freed even though the readers might be
using the tbl8 group entries. The freed tbl8 group can be reallocated
quickly. This results in incorrect lookup results.
RCU QSBR process is integrated for safe tbl8 group reclaim.
Refer to RCU documentation to understand various aspects of
integrating RCU library into other libraries.
To avoid ABI breakage, a struct __rte_lpm is created for lpm library
internal use. This struct wraps rte_lpm that has been exposed and
also includes members that don't need to be exposed such as RCU related
config.
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
This patch updates the feature list for hns3 PMD driver document.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch add more support for switch parser of PPPoE packet,
it enable parse tcp/udp L4 layer and ipv4/ipv6 L3 layer parser for
PPPoE payload, so we can use L4 dst/src port and L3 ip address as
input set for switch filter PPPoE related rule.
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Add device arguments to lock Rx/Tx contexts.
Application can either choose to lock Rx or Tx contexts by using
'lock_rx_ctx' or 'lock_tx_ctx' respectively per each port.
Example:
-w 0002:02:00.0,lock_rx_ctx=1 -w 0002:03:00.0,lock_tx_ctx=1
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Andrzej Ostruszka <aostruszka@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
This patch adds 'Scattered Rx' and 'Multiprocess aware' those are
supported by current hns3 PMD driver for feature list file named
hns3.ini and hns3_vf.ini.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support of LRO offload for hns3 PMD driver.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch refactors qat data into structures
which are local to the process and structures which
are intended to be shared by primary and secondary
processes. This enables qat devices to be used by
multi process applications.
Signed-off-by: Arek Kusztal <arkadiuszx.kusztal@intel.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Add a new option for PDCP cases to enable use of session
based fixed HFN value instead of per packet HFN which was
enabled by hfn override feature.
By default HFN override is enabled and if session based
fixed HFN need to be tested, add "--pdcp-ses-hfn-en" in the
command line.
Signed-off-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This reverts commit 51f3e107aca23a1cbc1a5ad9fdce7921340307b5.
For SNOW and ZUC algos the offset value for enryption and decryption
is converted to bytes. Hence RTE_CRYPTODEV_FF_NON_BYTE_ALIGNED_DATA
feature is not supported by the octeontx2 crypto pmd.
Fixes: 51f3e107aca2 ("crypto/octeontx2: enable non-byte aligned data")
Cc: stable@dpdk.org
Signed-off-by: Ankur Dwivedi <adwivedi@marvell.com>
This reverts commit 32b8f26adf8b26a55230408ff6adffd4b2327e52.
For SNOW and ZUC algos the offset value for enryption and decryption
is converted to bytes. Hence RTE_CRYPTODEV_FF_NON_BYTE_ALIGNED_DATA
feature is not supported by the octeontx crypto pmd.
Fixes: 32b8f26adf8b ("crypto/octeontx: enable non-byte aligned data")
Cc: stable@dpdk.org
Signed-off-by: Ankur Dwivedi <adwivedi@marvell.com>
Add support to the QAT SYM PMD for the DOCSIS protocol, through the
rte_security API. This, therefore, includes adding support for the
rte_security API to this PMD.
Signed-off-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Mairtin o Loingsigh <mairtin.oloingsigh@intel.com>
Add support to the AESNI-MB PMD for the DOCSIS protocol, through the
rte_security API. This, therefore, includes adding support for the
rte_security API to this PMD.
Signed-off-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Mairtin o Loingsigh <mairtin.oloingsigh@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Add support for DOCSIS protocol to rte_security library. This support
currently comprises the combination of Crypto and CRC operations.
Signed-off-by: David Coyle <david.coyle@intel.com>
Signed-off-by: Mairtin o Loingsigh <mairtin.oloingsigh@intel.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
