Update RX path to reflect Chelsio T6 register value changes.
Update ingress pack boundary value based on maximum payload size
that can be accommodated by underlying PCI. Update ingress pad
boundary value based on smallest memory controller bus width
possible. Enforce alignment for free list pointer start address.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Update informational prints pertaining to underlying hardware.
Add bootstrap firmware version and expansion ROM version prints.
Move the prints to a single function.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Add 25G and 100G link speeds and update supported port modules.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Move code to get the available ports from the firmware after it had
been reset. This ensures that driver uses the latest info on available
ports after firmware reset.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Update flash part identification and decoding to accommodate new
flash parts.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Add code to detect and run T6 devices. Update PCI ID Device table
with Chelsio T6 device ids and update documentation.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
This patch adds basic offloading support, widely expected in a PMD.
Verify IPv4 and UDP/TCP checksums upon packet reception, and set
ol_flags accordingly.
On Tx, set IPv4 and UDP/TCP checksums when required, considering
ol_flags.
Signed-off-by: Pascal Mazon <pascal.mazon@6wind.com>
The following two flow rules (testpmd syntax) should not collide:
flow create 0 priority 1 ingress pattern eth / ipv4 / end actions drop / end
flow create 0 priority 1 ingress pattern eth / ipv6 / end actions drop / end
But the eth_type in the associated TC rule was set to either "ip" or
"ipv6". For TC, they could thus not have the same priority.
Use ETH_P_ALL only in the TC message to make sure those rules can
coexist.
Fixes: de96fe68ae ("net/tap: add basic flow API patterns and actions")
Cc: stable@dpdk.org
Signed-off-by: Pascal Mazon <pascal.mazon@6wind.com>
In order to check the congestion state of Egress FQs,
this qbman function will be used by the DPAA2 Ethernet PMD.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Typically when the PMD issues a Rx command to DPAA2 hardware,
the HW writes the available descriptors into the given memory.
The RX function then processes the frames and prepare them as
mbufs.
This patch adds support to issue another pull request to hardware
in another memory location, before we start processing the output
of the first request. This help in controlling the CPU cycles
wasted during the wait for the hardware to write the descriptors.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
DPAA2 hardware support the option to configure
multiple memories for Rx recv buffer (DPAA2-DQRR).
Each Rx request executing is called as 'DQ' request.
This patch adds routines to get information w.r.t each DQ request.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The DPAA2 driver is not using the DPAA2 frame descriptor
software annotation area. This patch reduces the
PTA length to zero and adjust the RX Buffer Layout
accordingly.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This code in device init is not required, as the buffer
layout setting is also being programmed during queue configuration.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Add subsystem device id of CN23xx cards and expose speed capability of
devices. Update liquidio feature file to mark support.
Signed-off-by: Shijith Thotton <shijith.thotton@caviumnetworks.com>
Before this patch, flex_filter->index was always zero when it was read
and used after rte_zmalloc. The corresponding code was therefore moved
into the add and delete parts of the if/else statement.
Fixes: 231d43909a ("igb: migrate flex filter to new API")
Cc: stable@dpdk.org
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
i210/i211 also support flex filters. Tested on i210.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Completion buffer size was computed wrongly, causing
completion polling to wraparound too early and miss entries.
Fixing it by using Direct Verbs to query the CQ info.
Fixes: 6218063b39 ("net/mlx5: refactor Rx data path")
Fixes: 1d88ba1719 ("net/mlx5: refactor Tx data path")
Cc: stable@dpdk.org
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
On error, we also need to zero the bytes transmitted.
Fixes: f4ff17a465 ("net/af_packet: guard against buffer overruns in Tx path")
Cc: stable@dpdk.org
Signed-off-by: Chas Williams <ciwillia@brocade.com>
Required to be able to use logging in the secondary process
where Ethernet device pointer stored in sfc_adapter is invalid.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Added a debug function to print enic filters and actions when
rte_validate_flow is called. Compiled in CONFIG_RTE_LIBRTE_ENIC_DEBUG_FLOW
is enabled and log level is INFO.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
5-tuple exact Flow support for 1200 series adapters. This allows:
Attributes: ingress
Items: ipv4, ipv6, udp, tcp (must exactly match src/dst IP
addresses and ports and all must be specified).
Actions: queue and void
Selectors: 'is'
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Flow support for 1300 series adapters with the 'Advanced Filter'
mode disabled via the UCS management interface. This allows:
Attributes: ingress
Items: Outer eth, ipv4, ipv6, udp, sctp, tcp, vxlan. Inner eth, ipv4,
ipv6, udp, tcp.
Actions: queue and void
Selectors: 'is', 'spec' and 'mask'. 'last' is not supported
With advanced filters disabled, an IPv4 or IPv6 item must be specified
in the pattern.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
For VICs with filter tagging, support the MARK and FLAG actions
by setting appropriate mbuf ol_flags if there is a filter match.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Flow support for 1300 series adapters with the 'Advanced Filter'
mode enabled via the UCS management interface. This enables:
Attributes: ingress
Items: Outer eth, ipv4, ipv6, udp, sctp, tcp, vxlan. Inner eth, ipv4,
ipv6, udp, tcp.
Actions: queue, and void
Selectors: 'is', 'spec' and 'mask'. 'last' is not supported
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Stub callbacks for the generic flow API and a new FLOW debug define.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Update the base functions for the Cisco VIC. These files are mostly
common with other VIC drivers so are left alone is as much as possible.
Includes in a new filter/action interface which is needed for Generic
Flow API PMD support. Update FDIR code to use the new interface.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Unfortunately the datasheet has a mistake. The
address of the TX error counter is wrong.
Fixes: 8db9e2a1b2 ("i40e: base driver")
CC: stable@dpdk.org
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
