Since the communication between PF/Switch Manager, VF/PF is
asynchronous through mailbox, it's hard to determine when Switch
Manager/PF host will send the default vlan to PF/VF. So, it's
necessary to set default vlan until the device is started.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
After acquiring MAC address from HW, it's necessary to validate
MAC address before use.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
In fm10k, PF driver needs to communicate with switch through
mailbox if it needs to add/delete MAC address.
This fix will validate if switch is ready before going forward.
Then, it is necessary to acquire LPORT_MAP info after issuing
MAC addr request to switch.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
In TX side, bit FM10K_TXD_FLAG_LAST in TX descriptor only is set
in the last descriptor for multi-segment packets. But current
implementation didn't set all the fields of TX descriptor, which
will cause descriptors processed now to re-use fields set in last
scroll. If FM10K_TXD_FLAG_LAST bit was set in the last round and
it happened this is not the last descriptor of a multi-segnment
packet, HW will send out the incomplete packet out and leads to
data intergrity issue.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
fm10k can't receive frame greater than 1536 and Scatter RX
function can't work correctly. The root cause is
SRRCTL.FM10K_SRRCTL_BUFFER_CHAINING_EN bit is not enabled.
Test report: http://dpdk.org/ml/archives/dev/2015-June/019242.html
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
As RX buffer is aligned to 512B within mbuf, some bytes are reserved
for this purpose, and the worst case could be 511B. But SRR reg
assumes all buffers have the same size. In order to fill the gap,
we'll have to consider the worst case and assume 512B is reserved.
If we don't do so, it's possible for HW to overwrite data to next
mbuf.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Both PF and VF shared code in function fm10k_stats_get().
The function works well with PF, but has problem with VF since
VF has less queues than PF.
Fixes: a6061d9e70 ("fm10k: register PF driver")
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Original implementation required mbuf size should be greater than
ETHER_MAX_VLAN_FRAME_LEN, which is not necessary. If it's less
than that value, scatter function will be selected and incoming
packets greater than mbuf size will be filled into several mbufs.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
Add functions to support promiscuous/allmulticast enable and
disable.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Tested-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
For there're only laser ports on x550 before, we only considered laser
ports for the testpmd CLIs "port start/stop ...". Now we have new x550
devices which have copper ports. Use the API for copper to enable/disable
these ports.
And also let the testpmd CLI "set link-up/down ..." support copper
ports.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
When TSO is used with IPv6, generated frames are incorrect.
L4 frame is OK, but length field of IPv6 header was not populated correctly.
IXGBE_ADVTXD_TUCMD_IPV6 flag is set for better readability, even if it
does nothing.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Current ixgbe VF base driver only really read the status register when:
- get_link_status is true
- link reset
- mailbox timeout.
We only set get_link_status to true when we start the PF/VF, so
following calls to ixgbe_dev_link_update will just keep the old link
status unless the link has been reset.
Because of this behaviour, when the link status of the PF changes after
the VF has been initialized, we do not read the current status register
from the nic and instead we just keep the old link status.
Fix the problem by setting this field to true before calling
ixgbe_check_link function from base driver. We don't need to check after
this call for get_link_status anymore, so remove it.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
The logic to select ixgbe VF RX function is different than PF side.
There are a few issues with its current state:
- it does not allow to select ixgbe_recv_pkts_vec among other options.
- it can cause memory corruption for scatter mode as it does not allocate
enough entries in sw_ring.
- when checksum is enabled, incorrect vector RX function is selected.
To solve above issues, change the VF RX function selection logic to
mimic PF side.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The flexbytes offset can not be set, because the value is over written
when fdir is enabled.
This patch fixes this issue, and also removes some reduplicate lines.
Fixes: d54a988826 ("ixgbe: support flexpayload configuration of flow director")
Reported-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: David Marchand <david.marchand@6wind.com>
On x550, flow director doesn't support other IP packets directly.
If we want to monitor IP other packets, the L4 protocol and ports must
be masked. It means, on x550, if we want to add a flow director filter
for other IP packets, a flow director mask must have been configed to
mask L4 protocol and ports.
Return err when the user try to config a flow director filter for other
IP packets without flow director mask configed before. And print err log
for it.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch sets the setup_EEE function pointer to NULL for the
interfaces which do not support EEE (Energy Efficient Ethernet).
Currently only the KR backplane interface (0x15AB) supports EEE.
Setting this pointer to NULL prevents EEE registers from being
incorrectly modified and gives base drivers a flag to check for
EEE support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em PHY reset function ixgbe_reset_phy_t_X550em.
ixgbe_reset_phy_t_X550em calls the reset PHY generic, and then enables
the x550em PHY LASI(Link Alarm Status Interrupt) interrupts.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Set the lan_id before the first I2C access. The existing call was
clearly being done after a previous I2C access in the same function
and that can't be right, so call the set_lan_id method earlier. At
this point it probably doesn't matter for this QSFP function, but
it makes sense to do it consistently anyway.
On X550, be sure to set the lan_id before using it to configure the
mux control output, else the mux will not be controlled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The introduction of ixgbe_get_bus_info_X550em failed to call the
set_lan_id method to set the func and lan_id and deal with port-
swapped configurations. Add the call to resolve the problem.
Fixes: 4cf0bb32a9 ("ixgbe/base: get X550 bus info")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking x550em
PHY link. We check that both the MAC and external x550em PHY have link.
This is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em external PHY interrupt and forced 1G/10G
support. Support includes enabling and handling Link Status
Change and Thermal Sensor interrupt. ixgbe_handle_lasi has been added
to the API for handling the interrupts received from x550em PHY.
ixgbe_enable_lasi_ext_t_x550em and ixgbe_get_lasi_ext_t_x550em have been
added to X550em to enable mask and check interrupt flags for x550em PHY.
Forced 1G/10G link speed is handled via ixgbe_setup_mac_link_t_X550em.
ixgbe_setup_mac_link_t_X550em sets up the internal PHY and
external PHY link to either 10G or 1G based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em Auto neg Flow Control support to
ixgbe_device_supports_autoneg_fc and sets the x550em setup_fc function
pointer to ixgbe_setup_fc_generic. ixgbe_setup_fc_generic is used for
x550em because flow control is setup on the external PHY via MDIO, when
ixgbe_setup_fc_X550em sets up flow control on the internal PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch cleans up the ixgbe_setup_internal_phy_ x550em() function as follows:
- Renames it to ixgbe_setup_internal_phy_t_x550em to clarify that it is
specific to copper
- Returns an error if called for non-copper devices
- Corrects the comments
- Removed the LASI(Link Alarm Status Interrupt) status register checks as
this was incorrect and never worked correctly anyway.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch changes the return value for ixgbe_setup_internal_phy_t_x550em
when link is down to IXGBE_SUCCESS.
The driver will call ixgbe_setup_internal_phy_t_x550em when a link status
change is reported. The links status change can occur on link up or link
down, and if the link status change is for link down then there is no iXFI
setup necessary and no error condition needs to be returned.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The following patch moves the handling of the I2C MUX (which is only
used for x550em SFP+ devices) out of the ixgbe_x540.c file and
into the ixgbe_x550.c file where it belongs.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The init flow is simplified. We no longer wait for the PHY FW init
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be "un-stalled". SW no longer needs to put the PHY in
low-power mode or enable the transceiver.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For the KR backplane which is different from other backplane,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SW Low Power Link Up (LPLU) support for x550em PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SFP+ dual-speed support.
82599 fiber link code was moved from ixgbe_82599.c to ixgbe_commom.c
for use by X550em, and the API was updated to support the common code
usage. SFP MAC link code is added to x550em.
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC (Forward Error Correction) feature can improve BER (Bit Error Rate)
but uses more power to do so. It also cannot be used with
EEE (Energy Efficient Ethernet).
EEE is an important feature, and we have no known BER issues, so FEC
is not needed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. So,
put the code in a function so it can be used in more than one place.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The driver now needs to issue a firmware command to inform the
firmware that a driver is coming up. This prevents the possibility
of the firmware and the driver configuring the PHY at the same
time. Upon completion of the command, the firmware will no longer
be configuring the PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
A retry count of 10 is likely to run into problems on X550 devices
that have to detect and reset unresponsive CS4227 devices. So,
reduce the I2C retry count to 3 for X550 and above. This should
avoid any possible regressions in existing devices.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Most I2C accesses take and release semaphores for each access. It's
also necessary to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
All bits in FDIRTCPM and FDIRUDPM are set to 1 when
ixgbe_fdir_set_input_mask_82599 is called. Not settings these bits will cause
TCP and UDP packets to be filtered out when NVGRE or VXLAN mode is enabled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch moves the check of the return value from
ixgbe_start_hw_generic after the function is called.
Previously we had the code to disable relaxed ordering in
between, which seems a bit out of place.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Remove the redundant "from".
There's a typo in the code comment for FC end
of Frame Exception (FCEOFe/IPE), so fixed the typo.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Fix warning messages "cast to pointer from integer of different size" when
compiling DPDK in 32 bit with Mellanox PMD.
SGE addresses are 64 bit integers, converting them to pointers must be done
through uintptr_t to avoid compilation warnings when those have a different
size.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Fix NULL dereference if virtio control queue is not negotiated.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Negotiate the virtio ring size. The host may allow for very large
rings but application may only want a smaller ring.
Conversely, if the number of descriptors requested exceeds the virtio
host queue size, then just silently use the smaller host size.
This fixes issues with virtio in non-QEMU envirionments.
For example Google Compute Engine allows up to 16K elements
in ring.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Change the features from bit mask to bit number. This allows the
DPDK driver to use the definitions from Linux (yes the header
files already use a license compatiable with DPDK). This makes DPDK
driver handle future feature bit changes.
Get rid of double negative code in the feature bit intialization.
Instead just have a new define with the list of feature bits implemented.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Don't attempt to set the MAC address table unless the host allows
it in feature negotiation. Also, don't return a value from mac_table_set
since all callers ignore the return value.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
If negotiation with host says that controlling Rx mode is
not supported, then don't try.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Putting blank line between function and following conditional
just wastes screen space, and makes code less obvious.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
