The conclusion is that this method really can tell the perfect from the
less than perfect ACPI counters.
It is in fact probably a bit more discriminative than that, but we
will rather condemn some otherwise perfect counters to the slightly
slower "-safe" version, than certify a counter as perfect which
will let us down later.
Many thanks to all the people who sent email reports!
by the hardware are still marked as owned. Handle this by installing a
timeout handler to collect this descriptor to avoid having received
packets remain unhandled until the next one arrives.
- remove some useless code from the status change handler that was intended
to enable the the MII drivers for external phys; this is already done
during interface initialization, and the deleted code made some
assumptions about phy addresses that do not seem to hold true on newer
cards. This should get at least one of the two hmes of newer Netra t1
machines working.
- correct the interrupt resource allocation
- bump the number of RX descriptors, lower values cause promblems on some
machines
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
3c996B-T, with the 5701 rev B5 ASIC). One thing that confuses me
still is that the 'link state change' bit in the status block seems
to change state an awful lot. I have a workaround for this in place
now, but it needs more investigation. For the moment though, this
is enough to get the driver to work with this card.
soon because it's just getting harder and harder to find switches
that correctly implement the GET ALL NEXT subcommands for the SNS
protocol.
Latch up result out pointer and set a busy flag when we're looking
at the response queue. This allows for a cleaner way to make sure
we don't get multiple CPUs trying to read the same response queue
entries.
Change how isp_handle_other_response returns values (clarity).
Make PORT UNAVAILABLE the same as PORT LOGOUT (force a LIP).
Do some formatting changes.
MFC after: 0 days
keep gcc-3.1+ happy:
ata-all.c:410: warning: deprecated use of label at end of compound statement
ata-all.c:587: warning: deprecated use of label at end of compound statement
ata-raid.c:99: warning: deprecated use of label at end of compound statement
ata-raid.c:151: warning: deprecated use of label at end of compound statement
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
"Fixed" format printf error in previous commit. This file is not
formatted in KNF. Partially restore bug for bug compatibility: indent
the printf args too much, but don't format them for 160-column terminals.
than %u for printing signed 64-bit types. It fails on different machines,
and has the wrong signdness.
Fixed old printf format error on the same line. %u is not suitable for
printing 32-bit types on all machines.
o Add exerpimental support for identifying lucent cards. All of mine
come back with ID of 1, but NetBSD committed code for 5. So accept
both.
o rename wi_prism2_ver to wi_firmware_ver so that we could, if necessary,
do special things for lucent cards too.
o Bring in a small part of the changes from airtools: The wi_cmd function
now takes two additional arguments. I didn't bring in their ioctls yet.
o eliminate the use of LE16TOH, and remove its define.
o Print the firmware as if there were 100 versions instead of 10. This means
that 6.1 and 6.10 aren't confusing to people. We now print 6.01 in the
former case.
# A good junior hacker project would be to merge the NetBSD, FreeBSD, and
# OpenBSD drivers into one source base.
ohcivar.h (1.22), uhcivar.h (1.29):
============================================================
date: 2000/04/25 09:20:55; author: augustss;
Move the size of the mapped bus_space region into the bus
independent softc.
============================================================
ohci.c (1.88), uhci.c (1.112):
============================================================
date: 2000/04/25 14:28:13; author: augustss;
Insert (very conservative!) bus_space_barrier() calls at
all register accesses.
The bus_space(9) man page says you've gotta have them...
============================================================
usbdi.c (1.61):
===================================================================
revision 1.61
date: 2000/01/31 20:13:07; author: augustss; lines: +20 -4
Change the way the HC done method is invoked a little.
===================================================================
usbdi.c (1.65):
===================================================================
revision 1.65
date: 2000/03/08 15:34:10; author: augustss; lines: +4 -2
Get the status right when a polled transfer times out.
===================================================================
ohci.c (1.79), uhci.c (1.89), uhcivar.h (1.24), usb_port.h (1.22),
usbdivar.h (1.48):
===================================================================
date: 2000/03/23 07:01:46; author: thorpej;
New callout mechanism with two major improvements over the old
timeout()/untimeout() API:
- Clients supply callout handle storage, thus eliminating problems of
resource allocation.
- Insertion and removal of callouts is constant time, important as
this facility is used quite a lot in the kernel.
The old timeout()/untimeout() API has been removed from the kernel.
===================================================================
uhci.c (1.80), usbdi.c (1.66):
===================================================================
date: 2000/03/23 18:59:10; author: thorpej;
Shake out some bugs from the callout changes.
===================================================================
ohci.c (1.80), uhci.c (1.91), uhcivar.h (1.25), usb_port.h (1.23),
usbdi.c (1.67), usbdivar.h (1.49):
===================================================================
date: 2000/03/24 22:03:30; author: augustss;
Some cleanup and renaming of the callouts used in USB drivers.
===================================================================
uhci.c (1.92), uhcivar.h (1.26):
===================================================================
date: 2000/03/24 22:57:58; author: augustss;
Two major changes:
Make each xfer have its own intr_info. This is necessary if we want
to queue multiple xfers on an endpoint. This should get rid of the
(mostly harmless) DIAGNOSTICs about intr_infos (not) being done.
Change (again!) how xfers are aborted. Aborting a TD is a nightmare
on the braindead UHCI controller. (Unless you stop the HC, thereby
losing isoc traffic.) Hopefully I got it right this time.
===================================================================
usbdivar.h (1.50):
===================================================================
revision 1.50
date: 2000/03/25 00:10:19; author: augustss; lines: +4 -2
GC an unsued field and add some DIAGNOSTIC in xfer.
===================================================================
ums.c: Use the callout functions instead of the timeout ones.
uhci.c (1.93):
===================================================================
revision 1.93
date: 2000/03/25 00:11:21; author: augustss;
lines: +26 -1
Add more DIAGNOSTIC when aborting isoc.
===================================================================
uhci.c (1.94), usbdivar.h (1.51):
===================================================================
date: 2000/03/25 07:13:05; author: augustss;
More DIAGNOSTIC.
Initialize a callout handle I forgot.
===================================================================
uhci.c (1.95):
===================================================================
revision 1.95
date: 2000/03/25 07:23:12; author: augustss;
Exp; lines: +24 -7
Improve uhci_dump_ii().
===================================================================
ohci.c (1.81), uhci.c (1.96), uhcivar.h (1.27), usb_subr.c (1.68),
usbdi.c (1.68), usbdivar.h (1.52):
===================================================================
date: 2000/03/25 18:02:33; author: augustss;
Rename and move around callout handles to make it more sane.
Add some DIAGNOSTIC.
Fix buglet in isoc abort on UHCI.
===================================================================
uhci.c (1.98):
===================================================================
revision 1.98
date: 2000/03/27 07:39:48; author: augustss; lines: +12 -4
Make it compile without DIAGNOSTIC.
===================================================================
uhci.c (1.99):
===================================================================
revision 1.99
date: 2000/03/27 08:01:09; author: augustss; lines: +1 -5
Remove some debug nonsense.
===================================================================
uhci.c (1.100):
===================================================================
revision 1.100
date: 2000/03/27 09:41:36; author: augustss; lines: +13 -3
Don't mess with QH in bulk abort for the moment.
===================================================================
uhci.c (1.102):
===================================================================
revision 1.102
date: 2000/03/27 22:42:57; author: augustss; lines: +66 -26
Be a little more careful when aborting.
Preallocate some TDs for large buffers.
===================================================================
uhci.c (1.103):
===================================================================
date: 2000/03/28 09:47:10; author: augustss; lines: +11 -1
Another patch for xfer abort...
XXX The current xfer queueing and aborting semantics should really
XXX be changed. It cannot be implemented in a sane way on UHCI.
XXX One day when I have lots of time I'll redesign it...
===================================================================
uhci.c (1.104): Correct a debug message.
uhci.c (1.105): Be more defensive in a DIAGNOSTIC test.
uhci.c (1.106):
===================================================================
revision 1.106
date: 2000/03/29 01:49:13; author: augustss; lines: +14 -309
*SIGH* Revert back to the old method of aborting xfers.
I had tested the new stuff for two months now, but as soon as I commited
it the problems started to appear. Murphy, no doubt...
===================================================================
usb_subr.c (1.70), usbdi.c (1.71), usbdivar.h (1.53):
===================================================================
revision 1.70
date: 2000/03/29 01:45:20; author: augustss; lines: +2 -1
Do not accept new xfers for queuing while a pipe is aborting.
===================================================================
to put the device into 8 bit mode a second time. This appears to have
no ill effects on other devices, and appears to be necessary for the
xircom modem.
Submitted by: gwk@sgi.com, many others that found his patch in the archives.
the bio and buffer structures to have daddr64_t bio_pblkno,
b_blkno, and b_lblkno fields which allows access to disks
larger than a Terabyte in size. This change also requires
that the VOP_BMAP vnode operation accept and return daddr64_t
blocks. This delta should not affect system operation in
any way. It merely sets up the necessary interfaces to allow
the development of disk drivers that work with these larger
disk block addresses. It also allows for the development of
UFS2 which will use 64-bit block addresses.
Problem:
selwakeup required calling pfind which would cause lock order
reversals with the allproc_lock and the per-process filedesc lock.
Solution:
Instead of recording the pid of the select()'ing process into the
selinfo structure, actually record a pointer to the thread. To
avoid dereferencing a bad address all the selinfo structures that
are in use by a thread are kept in a list hung off the thread
(protected by sellock). When a selwakeup occurs the selinfo is
removed from that threads list, it is also removed on the way out
of select or poll where the thread will traverse its list removing
all the selinfos from its own list.
Problem:
Previously the PROC_LOCK was used to provide the mutual exclusion
needed to ensure proper locking, this couldn't work because there
was a single condvar used for select and poll and condvars can
only be used with a single mutex.
Solution:
Introduce a global mutex 'sellock' which is used to provide mutual
exclusion when recording events to wait on as well as performing
notification when an event occurs.
Interesting note:
schedlock is required to manipulate the per-thread TDF_SELECT
flag, however if given its own field it would not need schedlock,
also because TDF_SELECT is only manipulated under sellock one
doesn't actually use schedlock for syncronization, only to protect
against corruption.
Proc locks are no longer used in select/poll.
Portions contributed by: davidc
-#if defined(__FreeBSD__) && __FreeBSD_version__ >= 500023
+#if defined(__FreeBSD__) && __FreeBSD_version >= 500023
is a genuine bug -- __FreeBSD_version__ does not exist.
The other one:
-#if (__FreeBSD__ < 5)
+#if (__FreeBSD_version < 500000)
pops out when you cross-compile the code:
__FreeBSD__ is a compiler predefine,
__FreeBSD_version is defined in <sys/param.h> .
Given that in this case (and all others in sys/dev/usb and sys/i4b)
the goal is to adapt to a different kernel interface, and not to
a compiler feature, I believe the correct form is the second one
(in the best case the two are synonyms so the change does not break
anything anyways).
it worked- but I ran into a case with a 2204 where commands were being lost
right and left. Best be safe.
For target mode, or things called if we call isp_handle_other response- note
that we might have dropped locks by changing the output pointer so we bail
from the loop. It's the responsibility of the entity dropping the lock to
make sure that we let the f/w know we've read thus far into the response
queue (else we begin processing the same entries again- blech!).
MFC after: 1 day
the upcoming 7.4 family (7xxx controllers).
- improved error reporting and handling
- more diagnostic output
- add extra command packet definitions
- merge sources again with -stable
by removing parentheses. The main bug is in gcc: on machines with
64-bit longs and 64-bit long longs,
(unsigned long long)rdp->total_sectors / ((1024L * 1024L) / DEV_BSIZE))
has type plain unsigned long instead of the correctly promoted type
unsigned long long, so it can not be printfed using %llu format. Even
1ULL / 1L is mispromoted. Anyway, casting the correct operand
automatically avoids the problem. We do not want to to pessimize the
division; we just want to convert to a common maximal type for printing.
Some buggy firmware workarounds. Fix some endian bugs.
These reduce the diffs from NetBSD, but NetBSD does have more changes since
my last manual merge.
Link if only ATAPI device in kernel config
Remove unused #includes
Rearrange a bit in ata-raid to make diff against -stable smaller
Enable wc as default again, dunne how this happend...
This makes other power-management system (APM for now) to be able to
generate power profile change events (ie. AC-line status changes), and
other kernel components, not only the ACPI components, can be notified
the events.
- move subroutines in acpi_powerprofile.c (removed) to kern/subr_power.c
- call power_profile_set_state() also from APM driver when AC-line
status changes
- add call-back function for Crusoe LongRun controlling on power
profile changes for a example
Add code to properly detach/attach disks that are part of a RAID.
Mark a disk that is attached on an ATA channel belonging to a
RAID as a spare disk that can be used for rebuilding failed RAID1's.
Add support for rebuilding failed RAID1's.
Several fixes to the detach/attach code.
For replacing a disk in a failed RAID1 do the following:
Find the controller channel# of the failed disk.
Exec 'atacontrol detach <channel#>' to free the disk from the system.
Replace the failed disk with a new one of at least the same size.
If your have your disks in drawers/enclosures this can be done with
the system still running.
Exec 'atacontrol attach <channel#>' to add the disk to the system and
mark it as a valid spare for rebuild.
Exec 'atacontrol rebuild <array#>'
The system will rebuild the array on the fly, the array can still
be used during this, although with slower performance.
Please let me know of any problems with this!
Sponsored by: Advanis Inc.
MFC after: 2 weeks
in most machines of the Sun Ultra series. This is a port of the NetBSD
driver which I enhanced to make use of the gather functionality and the
configurable RX buffer offset to avoid copying all received/sent packet
(instead, packets will be directly DMAd from mbuf chains and into mbuf
clusters now).
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
1/ conditionalise (#if 0) function that is not used.
Unused code left in place for netBSD compatibility.
2/ Recode loop to convince gcc that it does initialise a variable
(use do-while instead of for() so gcc knows that we always go through
at least once. Feel free to check my logic.
code into cardbus and s/pci/cardbus. This exposes a few pci_*
functions that are now static.
This work is similar to work Justin posted to the mobile list about a
year or two ago, which I have neglected since then.
This is a subset of his current work with the multiple inheritance
newbus architecutre. When completed, that will eliminate the need for
pci/pci_private.h.
Similar work is needed for the cardbus_cis and pccard_cis code as well.
the inter-value histogram for 2000 samples. If the width is 3 or less
for 10 consequtive samples, we trust the counter to be good, otherwise
we use the *_safe() method.
This method may be too strict, but the worst which can happen is that
we take the performance hit of the *_safe() method when we should not.
Make the *_safe() method more discriminating by mandating that the three
samples do not span more than 15 ticks on the counter.
Disable the PCI-ident based probing as a means to recognize good
counters.
Inspiration from: dillon and msmith
latch the acpi timer, resulting in weird deltas. The problem is severe
enough to adversely effect the timecounter code.
Default to the 'safe' version of the get-timecount function. The probe
will override it if a known-good chipset is found. This is temporary
until a more complete solution is found.
Reviewed by: phk
AIOGCAP ioctl reports software-emulated formats. It defaults to on. People
who use performance-sensitive audio software and do not want it to pick a
software-emulated audio format instead of one supported by their hardware
should turn it off.
This unbreaks isdnphone(1) on systems with PCM-only sound cards.
Approved by: cg
New locks are:
- pgrpsess_lock which locks the whole pgrps and sessions,
- pg_mtx which protects the pgrp members, and
- s_mtx which protects the session members.
Please refer to sys/proc.h for the coverage of these locks.
Changes on the pgrp/session interface:
- pgfind() needs the pgrpsess_lock held.
- The caller of enterpgrp() is responsible to allocate a new pgrp and
session.
- Call enterthispgrp() in order to enter an existing pgrp.
- pgsignal() requires a pgrp lock held.
Reviewed by: jhb, alfred
Tested on: cvsup.jp.FreeBSD.org
(which is a quad-CPU machine running -current)
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Convert to using a kthread rather than timeout() to avoid problems
with the interpreter sleeping.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Use _ADR as well as _BBN to get our bus number.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The ACPI global lock acquire takes a timeout value. I'm not sure what
we should do about timeouts on it; a deadlock against this lock is
catastrophic.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Kill off the timeouts that used to read _BIF and _BST. These are
invoked when the battery is actually read. timeout() is dangerous
in combination with ACPI, as the interpreter can block.
This driver still needs more work.
Use ACPI_SUCCESS/ACPI_FAILURE consistently.
The AcpiGetInto* interfaces are obsoleted by ACPI_ALLOCATE_BUFFER.
Add AcpiBatteryIsPresent helper to determine whether a battery device
is inserted.
Add ACPI_ALL_DRIVERS to the list of debug layers, now that we own the
namespace for this.
Pr:
OUT status. We are, apparently, required to force the f/w to log back in
if we want to try and talk to that disk again. This means either issuing
a LOGIN LOCAL LOOP PORT mailbox command, or by issuing a LIP. I've elected
to issue a LIP because this has a better chance of waking up the disk which
clearly just crashed and burned.
These should not occur at all. If they do, they should be darned rare.
MFC after: 1 week
to be able to use 48bit addressing mode, but says the 48bit
size of the disk is 0, which according to spec means it can
address zero sectors in 48bit mode, why then say it supports
48bit mode at all..
If you want QLogic to look at a potential f/w problem for FC cards, you really
have to provide them info in the format they expect. This involves dumping
a lot of hardware registers (> 300 16 bit registers) and a lot of SRAM
(> 128KB minimum). Thus all of this code is #ifdef protected which will
become an option so that the memory allocation of where to dump the crash
image is pretty expensive. It's worth it if you have a reproducible problem
because they have some tools that can tell them, given the f/w version,
the precise state of everything.
MFC after: 1 week
Appologies for making this one bulk commit, but I have tested all these
changes together and don't want to break anything by trying to disentangle
it.
o Make debugging a sysctl/tunable
o Remove flags word from yenta chip info, it is unused
o Make 16-bit card I/O range and 32-bit card I/O range tunables
o Start the rename of pccbb to cbb to match NetBSD by misc renames.
o Kill the now bogus list of softcs to create kthread. Instead, just
create the kthread in the attach routine.
o Remove sc_ from some structure names. It isn't needed.
o Refine chipset lookup code.
o Match generic PCI <-> CardBus bridges. We specifically don't generically
match PCI PCMCIA bridges because they are not, with one exception, yenta
devices.
o Add some comments about the why we need to have a function table ala
OLDCARD
o The PCI interrupt routing by using the ExCA registers is needed for
for all bridges, per the spec, not just TI ones.
o Collapse TOPIC95 and TOPIC95B.
o Using the ToPIC 97 and 100 datasheets, try to support these bridges better,
but more work is needed.
o Generally clarify some XXX comments and add them in a few places where
things didn't look right to me.
o Move interrupt generating register access until after we establish an ISR.
o Add support for YV and XV cards. X and Y are numbers to be determined
later (but maybe never).
o factor powerup code for 16-bit and 32-bit cards.
o When a card supports more than one voltage, prefer the lowest supported
volage. Windows does this, and MS's design guides imply this is the
right thing to do.
o Document race between kthread_exit(0) and kldunload's unmapping of pages
that John Baldwin and I discovered.
o Debounce the CSC interrupt a little better.
o When a 16-bit card is inserted when we don't have a pccard child,
warn about it better. Ditto for 32-bit card.
o Ack ALL the interrupt bits that we get, not just 0x1.
o maybe a couple minor style nits corrected.
the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
be compiled. Old tty ioctls are still used (possibly ifdef'ed) in at
least the following programs in the src tree:
atc des ee fontedit gdb gdbserver lock ntp perl5 tcsh telnet top vttest
rp.c:
Unremoved used variables so that the support for old ioctls actually
compiles.
Not tested at runtime by: bde
ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG,
ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES,
COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO,
NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS,
SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG.
Start using #! to comment out negative options and ## to comment out
broken options.
atapi-all.c:
Fixed rotted bits that were hiding under ATAPI_DEBUG.
atapi-cd.c:
#include "opt_ata.h" so that ACD_DEBUG is actually visible.
ata/atapi-tape.c
#include "opt_ata.h" so that AST_DEBUG is actually visible.
descriptors. This simplifies code for jumbo frames.
- Cleaned up coding conventions to make code more unix-like.
- Cleaned up code in if_em_fxhw.c and if_em_phy.c.
Added relevant comments.
MFC after: 1 week
More cleanups of the RAID1 failure mode code.
Add functionality that writes the changed RAID config setup
back to the disks (in controller BIOS specific format), so
that a reboot will make the BIOS pick up the changed config.
1) We shouldn't continue when we get a RX complete because we ack it
and the TX complete.
2) Fix a couple of spl leaks
(why splbio is needed in ISR, I cannot understand).
MFC after: 3 days
Also, add some 'const's to supress warnings. (Submitted back to NetBSD).
The original logs from NetBSD:
----------------------------
revision 1.90
date: 2001/12/03 01:47:12; author: augustss; lines: +4 -4
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.89
date: 2001/12/02 23:25:25; author: augustss; lines: +18 -2
Add a subroutine to search for a vendor/product pair.
----------------------------
Original NetBSD log messages are:
----------------------------
revision 1.23
date: 2001/12/12 15:48:18; author: augustss; lines: +132 -114
Add a scanner quirk for keeping the pipes open between device opening.
Idea from Enami.
----------------------------
revision 1.22
date: 2001/12/03 01:47:13; author: augustss; lines: +8 -16
Handle vendor/product lookup with a common routine.
----------------------------
revision 1.21
date: 2001/12/01 09:42:39; author: enami; lines: +4 -4
Shorten wmesg so that they can be distinguished in ps/top output.
----------------------------
revision 1.12
date: 2001/01/23 14:04:14; author: augustss; lines: +7 -1
Make sure driver attach/detach events are generated in a
consistent manner.
----------------------------
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
From the NetBSD logs:
revision 1.45
date: 2001/11/29 11:07:12; author: augustss; state: Exp; lines: +12 -2
Plug a memory leak in an error case.
----------------------------
revision 1.43
date: 2001/10/19 15:30:25; author: nathanw; state: Exp; lines: +5 -3
Match printers that report their interface as IEEE 1284 in addition to
bidirectional.
o Call bus_generic_setup_intr and check its return value. Don't setup
func until we successfully get the interrupt from our parent.
o Add comments about some maybe questionable stuff so I can check later
to make sure that it really is that way.
o Don't allow INTR_TYPE_FAST. Since we are sharing the interrupt between
CSC and the functions, they can't be FAST because fast interrupts can't
be shared.
o Add the same workaround for resume that we have in OLDCARD.
o Also, return the error from bus_generic_resume rather than ignoring it.
of I/O in 1.5. It looks like I got it right only for some of the
cases. Instead, allow ISA addresses as a special case. Most PCI
bridges decode this range. I need to investigate PCI bridges better
to know if this is always true or not, but for now assume that it is
since that seems to be the most common case.
# We need to allocate addresses better for the pccard stuff...
Submitted by: phk, mitsunaga-san
to fix their code.
ata stuff:
Change name of ar_attach to not colide with existing ar_attach in if_ar.c.
usb stuff:
Create a dummy function to satisfy a call to it when in DEBUG mode.
check is complicated by the fact that the Adaptec 5400S cards claim to use
1.x firmware also. PERC2/QC 1.x firmware is not compatible with this driver
and will cause a system hang.
MFC after: 3 days
disable MWI on 2300
based on function code, set an 'isp_port' for the 2312- it's a
separate instance, but the NVRAM is shared, and the second port's
NVRAM is at offset 256.
+ Enable RIO operation for LVD SCSI cards. This makes a *big* difference
as even under reasonable load we get batched completions of about 30
commands at a time on, say, an ISP1080.
+ Do 'continuation' mailbox commands- this allows us to specify a work
area within the softc and 'continue' repeated mailbox commands. This is
more or less on an ad hoc basis and is currently only used for firmware
loading (which f/w now loads substantially faster becuase the calling
thread is only woken when all the f/w words are loaded- not for each
one of the 40000 f/w words that gets loaded).
+ If we're about to return from isp_intr with a 'bogus interrupt' indication,
and we're not a 23XX card, check to see whether the semaphore register is
currently *2* (not *1* as it should be) and whether there's an async completion
sitting in outgoing mailbox0. This seems to capture cases of lost fast posting
and RIO interrupts that the 12160 && 1080 have been known to pump out under
extreme load (extreme, as in > 250 active commands).
+ FC_SCRATCH_ACQUIRE/FC_SCRATCH_RELEASE macros.
+ Endian correct swizzle/unswizzle of an ATIO2 that has a WWPN in it.
MFC after: 1 week
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
to ExCA register sets. These registers exist in both ISA and PCI
devices in a couple different ways, and this will provide a common
base for future building. This code is a rehash of the pccbb 16-bit
code, which was a rehash of the pcic code, which was a rehash of the
netbsd i82365 code. More hashing to come.
apply to this file. The correct message is:
throw_rude_remark: Make sure we're holding the config lock before
proceeding. There's no reason to assume that this
has ever happened, but the alternative might be a
double fault.
uhub.c: revision 1.37
usb.4: revision 1.30
usb.c: revision 1.38
usb.h: revision 1.40
usb_port.h: revision 1.21
usb_subr.c: revision 1.65
usbdi.h: revision 1.40
Split the attach/detach events up into device, driver and controller
attach and detach events.
The commit message from NetBSD was:
date: 2000/02/02 07:34:00; author: augustss; state: Exp;
Change the USB event mechanism to include more information
about devices and drivers. Partly from FreeBSD.
Also rework usbd to take these new event types into account.
for success, non-zero otherwise. The maestro and maestro3 drivers were
returning the format code, which was being interpreted as a failure code.
Fixed. No one seems to have noticed that the maestro driver was broken,
but I'll fix it anyways.
MFC after: 2 weeks
* be more specific in verbose boot messages
* allow the feeder subsystem to veto pcm* attaching if there is an error
initialising the root feeder
* don't free/malloc a new tmpbuf when resizing a snd_dbuf to the same size as
it currently is
* store the feeder description in the feeder structure instead of mallocing
space for it
usb.c: revision 1.39
revision 1.39
date: 2000/02/22 11:30:56; author: augustss; lines: +7 -1
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
usb.c: revision 1.41
revision 1.41
date: 2000/03/16 00:46:38; author: augustss; lines: +2 -2
Make the USB event queue longer. Mine overflows before the
(user-land) event handler has started. But then I have
about 25 devices connected. :)
ohci.c: revision 1.72 and 1.73
ohcivar.h: revision 1.19 and 1.20
uhci.c: revision 1.85
usbdi.h: a small part of revision 1.40
usbdivar.h: revision 1.47
Relevant commit messages from NetBSD are:
date: 2000/02/22 11:30:54; author: augustss; state: Exp;
Prepare a little for having USB interrupt processing done
outside the hard interrupt level (in a thread or a softintr).
No real soft processing done yet.
----------------------------
date: 2000/02/01 05:42:53; author: augustss; state: Exp;
Put some #ifdefs around power and shutdown hooks.
usb.c: -r1.35 - 1.37
usb_port.h: tiny bit of -r1.26 + an extra bit in the FreeBSD config section.
revision 1.37
date: 2000/01/24 18:35:51; author: thorpej; state: Exp; lines: +7 -1
Use config_pending.
----------------------------
revision 1.36
date: 1999/12/22 23:54:09; author: augustss; state: Exp; lines: +2 -2
Use the flags `locator' to govern if devices are detected early or
late during cold boot.
----------------------------
revision 1.35
date: 1999/12/20 02:12:23; author: augustss; state: Exp; lines: +8 -5
Make sure tsleep() is not called during cold boot.
stead of after
2) Honour NO_TEST_UNIT_READY quirk for atapi devices as well
3) Actually support FujiFilm FinePix 6800 camera's. Will very likely also
work for other FinePix models.
Based on a debug session about half a year ago with Nik Hibma.
MFC after: 2 weeks
extensively as none of my testboxes have speakers or an audio source at
present, but the chains built look correct and reading /dev/audio (ulaw,
translated from signed 16 bit little-endian) gives values within the
expected range for silence.
default format for the chosen subdevice cannot be obtained return an error
instead of returning success with an indeteterminate format selected.
note that this should never happen once the feederchain builder works for
recording.
ohci.c: -r1.69 to 1.71
ohcireg.h: -r1.14
Some of these deltas are based upon patches that we submitted back to
NetBSD. They got manifested slightly differently though, so I've brought
back those differences to bring our code bases closer together.
The logs from the NetBSD version of ohci.c:
revision 1.71
date: 2000/02/01 05:42:52; author: augustss; state: Exp; lines: +13 -2
Put some #ifdefs around power and shutdown hooks.
----------------------------
revision 1.70
date: 2000/01/31 22:35:13; author: augustss; state: Exp; lines: +7 -7
Rename TAILMASK to HEADMASK, since it really masks the head pointer.
From FreeBSD.
----------------------------
revision 1.69
date: 2000/01/31 22:09:13; author: augustss; state: Exp; lines: +18 -14
Change where the has table for physical-to-virtual address translation
is handled. Partly from FreeBSD.
ohci.c: -r1.68
ohcireg.h: -r1.13
date: 2000/01/31 20:17:25; author: augustss; state: Exp;
Fiddle with over-current protect when turning on port power to make
things work for some OHCI controllers.
uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
likely looking rate calculation.
Install interrupt handler before calling ich_init as the initialization
occasionally generates spurious interrupts.
These changes are derived from cg's work in progress version of this
driver.
at insert time. When asking gibbs for approval for an MFC, this was
his reply:
1) It leaks memory if it can't allocate a path.
2) It defers allocation of aic->path until the call to scan the
bus. This means the path may be NULL when an interrupt occurs
prior to the call to scan the bus (stray bus reset for instance),
which will lead to a panic.
3) The driver in current doesn't recover from the failure to allocate
aic->path. The driver doesn't check during normal operation if
the path is NULL, so again a panic will result.
4) aic_cam_rescan calls malloc with M_WAITOK. aic_cam_rescan is called
from attach where it isn't necessarily safe to sleep.
5) And most importantly, it co-opts the xpt_periph from the driver level.
This was never part of the design (xpt_periph used to be static). Making
a call of this type may completely confuse the XPT if other XPT operations
are ongoing.
In the long term, Justin and Warner agreed to implement solution where
CAM itself will initiate the bus rescan if a new bus is added. For
the time being (and in particular in light of the upcoming 4.5
release), we now have camcontrol available on the boot floppy, and can
have pccardd initiate the rescan through it.
previous commit, it should always print due to lack of {} around the
second line in the if statement. The message should likely say
something more like "There's no hardware responding at this IRQ.
Device not present (or disbaled)," but that is too long. We generally
don't give elementary advise in device driver messages anyway. Be
that as it may, the problem with it printing all the time should be
corrected.
One to notify the system that the MTU for VLAN can be 1500 so the vlan
will automatically be configured with a 1500 MTU the other is to ignore
the error case if the received frame is to long.
The frame size notification came from code in the SIS driver, and
the support for long frames derived from the NetBSD Tulip driver.
Tested on: 4 port D-Link adapter DFE-570TX 4 Intel 21143
Netgear card with 82c169 PNIC 10/100BaseTX
Reviewed by: ru (manpage), wpaul (not objected to), archie
Approved by: imp
Obtained from: NetBSD
o Remove bogus flags that aren't used (if we need them in the future, we can
add them back).
o Add support for the TI-1031. This is the only YENTA compatible PCI-PCMCIA
bridge that I'm aware of (all the others are PCIC on a PCI bus, which is
different).
Seigo Tanimura (tanimura) posted the initial delta.
I've polished it quite a bit reducing the need for locking and
adapting it for KSE.
Locks:
1 mutex in each filedesc
protects all the fields.
protects "struct file" initialization, while a struct file
is being changed from &badfileops -> &pipeops or something
the filedesc should be locked.
1 mutex in each struct file
protects the refcount fields.
doesn't protect anything else.
the flags used for garbage collection have been moved to
f_gcflag which was the FILLER short, this doesn't need
locking because the garbage collection is a single threaded
container.
could likely be made to use a pool mutex.
1 sx lock for the global filelist.
struct file * fhold(struct file *fp);
/* increments reference count on a file */
struct file * fhold_locked(struct file *fp);
/* like fhold but expects file to locked */
struct file * ffind_hold(struct thread *, int fd);
/* finds the struct file in thread, adds one reference and
returns it unlocked */
struct file * ffind_lock(struct thread *, int fd);
/* ffind_hold, but returns file locked */
I still have to smp-safe the fget cruft, I'll get to that asap.
instead of relying on the previous filters to be present.
Back out r1.125, as a reset is needed to unload any existing microcode,
(which clears the multicast addresses), as it is superceded by this change.
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
hw.midi.debug and hw.midi.seq.debug to 1 to enable debug log.
- Make debug messages human-frendly.
- Implement /dev/music.
- Add a timer engine required by /dev/music.
- Fix nonblocking I/O.
- Fix the numbering of midi and synth devices.
firmware to delay completion of commands so that it can attempt to batch
a bunch of completions at once- either returning 16 bit handles in mailbox
registers, or in a resposne queue entry that has a whole wad of 16 bit handles.
Distinguish between 2300 and 2312 chipsets- if only because the revisions
on the chips have different meanings.
Add more instrumentation plus ISP_GET_STATS and ISP_CLR_STATS ioctls.
Run up the maximum number of response queue entities we'll look at
per interrupt.
If we haven't set HBA role yet, always return success from isp_fc_runstate.
MFC after: 2 weeks
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
This gives a bit of a sluggish console, but it prevents the console from
getting stuck if we poll too fast, as well as other badness on certain
machines.
2. Fix a test for != 0 that should have been > 0.
Noticed by: Jamey Wood <Jamey.Wood@Sun.COM> and myself
Submitted by: tmm (2)
- Move from msleep/wakeup to condvar.
- Return either zero or a positive errno value from a function.
Return additional result via references.
- Unify the typedef of callback functions.
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
a packed array so sizeof work. This broke RFMON mode and passing
up 802.11 packets.
The Linux emulation code was derived from the open source Linux driver to
maintain compatibility.
LEAP support is added, hints from Richard Johnson. I've verified this
locally with PC350v42510.img firmware. More bug fixing from Marco to
fix long passwords.
Change DELAYs in flash part of driver to FLASH_DELAY which uses tsleep
so it doesn't look like your system died during a flash update.
Install header files in /usr/include/dev/an
Cleanup some ifmedia bugs add "Home" key mode to ifmedia and ancontrol.
This way you can manage 2 keys a little easier. Map the home mode into
key 5. Enhance ifconfig to dump the various configured SSIDs. I use
a bunch of different ones and roam between them. Use the syntax similar
to the WEP keys to deal with setting difference SSIDs.
Bump up up the Card capabilities RID since they added 2 bytes to it
in the latest firmware. Thankfully we changed it from a terminal
failure so the card still worked but the driver whined.
Some cleanup patches from Marco Molteni.
Submitted by: Richard Johnson <raj@cisco.com>
Marco Molteni <molter@tin.it>
and myself
Various checks: David Wolfskill <david@catwhisker.org>
Reviewed by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Approved by: Brooks Davis <brooks@freebsd.org>
Warner Losh <imp@freebsd.org>
Obtained from: Linux emulation API's from Aironet driver.
socreate(), rather than getting it implicitly from the thread
argument.
o Make NFS cache the credential provided at mount-time, and use
the cached credential (nfsmount->nm_cred) when making calls to
socreate() on initially connecting, or reconnecting the socket.
This fixes bugs involving NFS over TCP and ipfw uid/gid rules, as well
as bugs involving NFS and mandatory access control implementations.
Reviewed by: freebsd-arch
In order of importance:
* Make ugen use updated frlengths.
* More tests for NULL pipes.
* Generate better error codes on bulk write.
* Error messages in general.
(1) Don't attempt aquire the non-recursive lock sio_lock recursively.
Doing so caused unbounded recursion in some setups. E.g., if DDB,
BREAK_TO_DEBUGGER and WITNESS are configured; if the debugger is
entered using a break, then WITNESS will actually detect the invalid
recursion and will add to it attempting to print a message about it.
(2) Don't use sio_lock before it has been initialized. The old check
(sio_inited != 0) didn't work when sio_inited was boolean because
sio_inited was set too early, and became just wrong when sio_inited
was changed to a tri-state variable in rev.1.348.
Reported and fixed in another way by: fenner (1)
see people trip over it. Do not set the FIFO trigger to just before it
would otherwise overflow. Give it a little more slop so characters aren't
lost if the interrupt is delayed by other system activities.
MFC maybe: 7 days
- Temporary fix a bug of Intel ACPI CA core code.
- Add OS layer ACPI mutex support. This can be disabled by
specifying option ACPI_NO_SEMAPHORES.
- Add ACPI threading support. Now that we have a dedicate taskqueue for
ACPI tasks and more ACPI task threads can be created by specifying option
ACPI_MAX_THREADS.
- Change acpi_EvaluateIntoBuffer() behavior slightly to reuse given
caller's buffer unless AE_BUFFER_OVERFLOW occurs. Also CM battery's
evaluations were changed to use acpi_EvaluateIntoBuffer().
- Add new utility function acpi_ConvertBufferToInteger().
- Add simple locking for CM battery and temperature updating.
- Fix a minor problem on EC locking.
- Make the thermal zone polling rate to be changeable.
- Change minor things on AcpiOsSignal(); in ACPI_SIGNAL_FATAL case,
entering Debugger is easier to investigate the problem rather than panic.
to Phil Kernick:
"The problem is that in full duplex mode, the Conexant chip always reports a
carrier lost error, even when the frame is successfully sent. So, if we
have a Conexant chip, then ignore carrier lost when in full duplex
mode."
Since the Xircom chips seem to have the same issue and since we already
have a workaround for this, just expand the workaround test to also
check for DC_IS_CONEXANT().
to a label is inside an #ifdef block, then the label should *also* be
inside an #ifdef block. Hide the "done:" label which is only used if
DEVICE_POLLING is enabled under #ifdef DEVICE_POLLING.
must be cleared to prevent machine hanging (presently aflicts -current
and -stable).
Problem reported by Bruce Montague <brucem@cse.iitkgp.ernet.in>
PR: kern/29769 (probably)
otherwise breaks on the Alpha arch. I think this is wrong since i'd
actually like to probe for a PC architecture, not for a particular CPU
type. Anyway, now it's again the way it used to be.
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
- The MD functions critical_enter/exit are renamed to start with a cpu_
prefix.
- MI wrapper functions critical_enter/exit maintain a per-thread nesting
count and a per-thread critical section saved state set when entering
a critical section while at nesting level 0 and restored when exiting
to nesting level 0. This moves the saved state out of spin mutexes so
that interlocking spin mutexes works properly.
- Most low-level MD code that used critical_enter/exit now use
cpu_critical_enter/exit. MI code such as device drivers and spin
mutexes use the MI wrappers. Note that since the MI wrappers store
the state in the current thread, they do not have any return values or
arguments.
- mtx_intr_enable() is replaced with a constant CRITICAL_FORK which is
assigned to curthread->td_savecrit during fork_exit().
Tested on: i386, alpha
the link rate - some ich motherboards overclock ac97 out of the box.
Will hopefully replace this with a callibration loop in time for 4.5R
freeze.
Problem reported by Luigi Rizzo and fix derived from his code (put
diff in ich.c rather than ac97.c).
MFC after: 3 days
. The main device node now supports automatic density selection for
commonly used media densities. So you can stuff your 1.44 MB and
720 KB media into your drive and just access /dev/fd0, no questions
asked. It's all that easy, isn't it? :)
. Device density handling has been completely overhauled. The old way
of hardwired kernel density knowledge is no longer there. Instead,
the kernel now implements 16 subdevices per drive. The first
subdevice uses automatic density selection, while the remaining 15
devices are freely programmable. They can be assigned an arbitrary
name of the form /dev/fd[:digit]+.[:digit:]{1,4}, where the second
number is meant to either implement device names that are mnemonic
for their raw capacity (as it used to be), or they can alternatively
be created as "anonymous" devices like fd0.1 through fd0.15,
depending on the taste of the administrator. After creating a
subdevice, it is initialized to the maximal native density of the
respective drive type, so it needs to be customized for other
densities by using fdcontrol(8). Pseudo-partition devices (fd0a
through fd0h) are still supported as symlinks.
. The old hack to use flags 0x1 to always assume drive 0 were there is
no longer supported; this is now supposed to be done by wiring the
devices down from the loader via device flags. On IA32
architectures, the first two drives are looked up in the CMOS
configuration records though. On PCMCIA (i. e., the Y-E Data
controller of the Toshiba Libretto), a single drive is always
assumed.
. Other specialities like disabling the FIFO and not probing the drive
at boot-time are selected by per-controller or per-drive flags, too.
. Unit attentions (media has been changed) are supposed to be detected
now; density autoselection only occurs after a unit attention. (Can
be turned off by a per-drive flag, this will cause each Fdopen() to
perform the autoselection.)
. FM floppies can be handled now (on controllers that actually support
it -- not all do these days).
. Fdopen() can be told to avoid density selection by setting
O_NONBLOCK; this leaves the descriptor in a half-opened state where
only a few ioctls are accepted. This is necessary to run fdformat
on a device that uses automatic density selection (since you cannot
autoselect on an unformatted medium, obviously).
. Just differentiate between a plain old NE765 and the enhanced chips,
but don't try more; the existing code was wrong and only misdetected
the chips anyway.
BUGS and TODOs:
. All documentation update still needs to be done.
. Formatting not-so-standard format yields unpredictable results; i
have yet to figure out why this happens. "Standard" formats like
720 and 1440 KB do work, however.
. rc scripts are needed to setup device nodes with nonstandard
densities (like the old /dev/fdN.MMM we used to have).
. Obtaining device flags from the kernel environment doesn't work yet,
thus currently only drives that are present in (IA32) CMOS are
really detected. Someone who knows the odds and ends about device
flags is needed here, i can't figure out what i'm doing wrong.
. 2.88 MB still needs to be done.
Non-SMP, i386-only, no polling in the idle loop at the moment.
To use this code you must compile a kernel with
options DEVICE_POLLING
and at runtime enable polling with
sysctl kern.polling.enable=1
The percentage of CPU reserved to userland can be set with
sysctl kern.polling.user_frac=NN (default is 50)
while the remainder is used by polling device drivers and netisr's.
These are the only two variables that you should need to touch. There
are a few more parameters in kern.polling but the default values
are adequate for all purposes. See the code in kern_poll.c for
more details on them.
Polling in the idle loop will be implemented shortly by introducing
a kernel thread which does the job. Until then, the amount of CPU
dedicated to polling will never exceed (100-user_frac).
The equivalent (actually, better) code for -stable is at
http://info.iet.unipi.it/~luigi/polling/
and also supports polling in the idle loop.
NOTE to Alpha developers:
There is really nothing in this code that is i386-specific.
If you move the 2 lines supporting the new option from
sys/conf/{files,options}.i386 to sys/conf/{files,options} I am
pretty sure that this should work on the Alpha as well, just that
I do not have a suitable test box to try it. If someone feels like
trying it, I would appreciate it.
NOTE to other developers:
sure some things could be done better, and as always I am open to
constructive criticism, which a few of you have already given and
I greatly appreciated.
However, before proposing radical architectural changes, please
take some time to possibly try out this code, or at the very least
read the comments in kern_poll.c, especially re. the reason why I
am using a soft netisr and cannot (I believe) replace it with a
simple timeout.
Quick description of files touched by this commit:
sys/conf/files.i386
new file kern/kern_poll.c
sys/conf/options.i386
new option
sys/i386/i386/trap.c
poll in trap (disabled by default)
sys/kern/kern_clock.c
initialization and hardclock hooks.
sys/kern/kern_intr.c
minor swi_net changes
sys/kern/kern_poll.c
the bulk of the code.
sys/net/if.h
new flag
sys/net/if_var.h
declaration for functions used in device drivers.
sys/net/netisr.h
NETISR_POLL
sys/dev/fxp/if_fxp.c
sys/dev/fxp/if_fxpvar.h
sys/pci/if_dc.c
sys/pci/if_dcreg.h
sys/pci/if_sis.c
sys/pci/if_sisreg.h
device driver modifications
a GetAllNext response. Otherwise, we won't unswizzle
it correctly. This was found on linux/PPC.
This mandated creating another inline: isp_get_gan_response.
Introduce an additional device flag for those NICs which require the
transmit buffers to be aligned to 32-bit boundaries.
(the equivalen fix for STABLE is slightly simpler because there are
no supported chips which require this alignment there.)
