bus_get/set_resource methods are implemented in child device (iicbus).
As their implementation with bus_generic_rl_get/set calls do not
recurse up the tree, the versions in ig4 are never called.
Suggested by: jhb
If controller is allocated with IIC_NOWAIT option ig4 enables polled mode
for a period of allocation that makes possible to start I2C transfers
from the contexts where sleeping is not allowed e.g. from ithreads or
callouts.
They share common device driver code with different bus attachments
This commit starts a bunch of changes which have following properties:
Reviewed by: imp (previous version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D22016
In testing on a Dell Latitude 7480, having ig4.ko loaded during a
suspend caused the system to hang. It turns out that ig4iic_intr() was
being called after the device entered D3, and entered an infinite loop
because a read of the I2C status register returned all ones, causing us
to attempt to read a byte from the data buffer until one of the status
bits clears. This occured because ig4iic_pci0 shares an interrupt with
the VGA device on this laptop, so ig4iic_intr() gets called even when
there is no work to do. This is exactly the problem fixed by r342170,
which resolves the hang for me and allows suspend/resume to work with
ig4.ko loaded. So, re-enable autoloading of ig4.ko in the hope that
r342170 resolves the problem universally.
Reviewed by: gonzo
MFC after: 1 month (pending an MFC of r342170)
Differential Revision: https://reviews.freebsd.org/D18587
ig4(4) does not support suspend/resume but present on the hardware where
such functionality is critical, like laptops. Remove PNP info to avoid
breaking suspend/resume on the systems where ig4(4) load is not explicitly
requested by the user.
PR: 229791
Reported by: Ali Abdallah
Add PCI ids for I2C controllers on Apollo Lake platform. Also convert
switch/case probe logic into a table.
Reviewed by: avg
Differential Revision: https://reviews.freebsd.org/D16120
This was tested by Ben on HP Chromebook 13 G1 with a
Skylake CPU and Sunrise Point-LP I2C controller and by me on
Minnowboard Turbot with Atom E3826 (formerly Bay Trail)
Submitted by: Ben Pye <ben@curlybracket.co.uk>
Reviewed by: gonzo
Obtained from: DragonflyBSD (a4549657 by Imre Vadász)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13654
Add ACPI part for ig4 driver to make it work on Intel BayTrail SoC where
ig4 device is available only through ACPI
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8742
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
