correctly prepare KGSBASE msr to restore the user descriptor base on
the last swapgs during return to usermode.
Reported and tested by: peterj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
guest for which the rules regarding xsetbv emulation are known. In
particular future extensions like AVX-512 have interdependencies among
feature bits that could allow a guest to trigger a GP# in the host with
the current approach of allowing anything the host supports.
- Add proper checking of Intel MPX and AVX-512 XSAVE features in the
xsetbv emulation and allow these features to be exposed to the guest if
they are enabled in the host.
- Expose a subset of known-safe features from leaf 0 of the structured
extended features to guests if they are supported on the host including
RDFSBASE/RDGSBASE, BMI1/2, AVX2, AVX-512, HLE, ERMS, and RTM. Aside
from AVX-512, these features are all new instructions available for use
in ring 3 with no additional hypervisor changes needed.
Reviewed by: neel
API function 'vie_calculate_gla()'.
While the current implementation is simplistic it forms the basis of doing
segmentation checks if the guest is in 32-bit protected mode.
of the guest linear address space. These APIs in turn use a new ioctl
'VM_GLA2GPA' to convert the guest linear address to guest physical.
Use the new copyin/copyout APIs when emulating ins/outs instruction in
bhyve(8).
'struct vm_guest_paging'.
Check for canonical addressing in vmm_gla2gpa() and inject a protection
fault into the guest if a violation is detected.
If the page table walk is restarted in vmm_gla2gpa() then reset 'ptpphys' to
point to the root of the page tables.
indicate the faulting linear address.
If the guest PML4 entry has the PG_PS bit set then inject a page fault into
the guest with the PGEX_RSV bit set in the error_code.
Get rid of redundant checks for the PG_RW violations when walking the page
tables.
the UART FIFO.
The emulation is constrained in a number of ways: 64-bit only, doesn't check
for all exception conditions, limited to i/o ports emulated in userspace.
Some of these constraints will be relaxed in followup commits.
Requested by: grehan
Reviewed by: tychon (partially and a much earlier version)
the proper ICWx initialization sequence. It assumes, probably correctly, that
the boot firmware has done the 8259 initialization.
Since grub-bhyve does not initialize the 8259 this write to the mask register
takes a code path in which 'error' remains uninitialized (ready=0,icw_num=0).
Fix this by initializing 'error' at the start of the function.
These masks are documented in the Intel Architecture Instruction Set
Extensions Programming Reference (March 2014).
Reviewed by: kib
MFC after: 1 month
Set the accessed and dirty bits in the page table entry. If it fails then
restart the page table walk from the beginning. This might happen if another
vcpu modifies the page tables simultaneously.
Reviewed by: alc, kib
to a guest physical address.
PG_PS (page size) field is valid only in a PDE or a PDPTE so it is now
checked only in non-terminal paging entries.
Ignore the upper 32-bits of the CR3 for PAE paging.
- inserting frame enter/leave sequences
- restructuring the vmx_enter_guest routine so that it subsumes
the vm_exit_guest block, which was the #vmexit RIP and not a
callable routine.
Reviewed by: neel
MFC after: 3 weeks
XSAVE Extended Features for AVX512 and MPX (Memory Protection Extensions).
Obtained from: Intel's Instruction Set Extensions Programming Reference
(March 2014)
the legacy 8259A PICs.
- Implement an ICH-comptabile PCI interrupt router on the lpc device with
8 steerable pins configured via config space access to byte-wide
registers at 0x60-63 and 0x68-6b.
- For each configured PCI INTx interrupt, route it to both an I/O APIC
pin and a PCI interrupt router pin. When a PCI INTx interrupt is
asserted, ensure that both pins are asserted.
- Provide an initial routing of PCI interrupt router (PIRQ) pins to
8259A pins (ISA IRQs) and initialize the interrupt line config register
for the corresponding PCI function with the ISA IRQ as this matches
existing hardware.
- Add a global _PIC method for OSPM to select the desired interrupt routing
configuration.
- Update the _PRT methods for PCI bridges to provide both APIC and legacy
PRT tables and return the appropriate table based on the configured
routing configuration. Note that if the lpc device is not configured, no
routing information is provided.
- When the lpc device is enabled, provide ACPI PCI link devices corresponding
to each PIRQ pin.
- Add a VMM ioctl to adjust the trigger mode (edge vs level) for 8259A
pins via the ELCR.
- Mark the power management SCI as level triggered.
- Don't hardcode the number of elements in Packages in the source for
the DSDT. iasl(8) will fill in the actual number of elements, and
this makes it simpler to generate a Package with a variable number of
elements.
Reviewed by: tycho
with all bits set to 1 beyond the I/O permission bitmap.
Prior to this change accessing I/O ports [0xFFF8-0xFFFF] would trigger a
#GP fault even though the I/O bitmap allowed access to those ports.
For more details see section "I/O Permission Bit Map" in the Intel SDM, Vol 1.
Reviewed by: kib
freebsd-current. These CPU speed control techniques are usually unhelpful
at best. For now, continue building the relevant code into GENERIC so that
it can trivially be re-enabled at runtime if anyone wants it.
MFC after: 1 month
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
to sleep permanently by executing a HLT with interrupts disabled.
When this condition is detected the guest with be suspended with a reason of
VM_SUSPEND_HALT and the bhyve(8) process will exit.
Tested by executing "halt" inside a RHEL7-beta guest.
Discussed with: grehan@
Reviewed by: jhb@, tychon@
the 'HLT' instruction. This condition was detected by 'vm_handle_hlt()' and
converted into the SPINDOWN_CPU exitcode . The bhyve(8) process would exit
the vcpu thread in response to a SPINDOWN_CPU and when the last vcpu was
spun down it would reset the virtual machine via vm_suspend(VM_SUSPEND_RESET).
This functionality was broken in r263780 in a way that made it impossible
to kill the bhyve(8) process because it would loop forever in
vm_handle_suspend().
Unbreak this by removing the code to spindown vcpus. Thus a 'halt' from
a Linux guest will appear to be hung but this is consistent with the
behavior on bare metal. The guest can be rebooted by using the bhyvectl
options '--force-reset' or '--force-poweroff'.
Reviewed by: grehan@
by adding an argument to the VM_SUSPEND ioctl that specifies how the virtual
machine should be suspended, viz. VM_SUSPEND_RESET or VM_SUSPEND_POWEROFF.
The disposition of VM_SUSPEND is also made available to the exit handler
via the 'u.suspended' member of 'struct vm_exit'.
This capability is exposed via the '--force-reset' and '--force-poweroff'
arguments to /usr/sbin/bhyvectl.
Discussed with: grehan@
checks for special pcid values in invlpg_pcid_handler(). Forst check
for special values, and only then do PCID-specific page invalidation.
Minor fix to the style compliance, declare local variable at the
function start.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
kernel will now boot on both BIOS and EFI systems without modification.
Equivalent functionality in GENERIC requires making vt(9) the default console
driver, which is probably appropriate at this point.
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
replace the vt_vga driver with vt_efifb.
This is intended to help with snapshot builds only.
There is no intention to MFC this commit.
Sponsored by: The FreeBSD Foundation
Some of the code in xen-locore.S was picked from Cherry G. Mathew
amd64 Xen PV branch, but I've failed to set the proper copyright, so
do it now.
Approved by: gibbs
Status and Control register at port 0x61.
Be more conservative about "catching up" callouts that were supposed
to fire in the past by skipping an interrupt if it was
scheduled too far in the past.
Restore the PIT ACPI DSDT entries and add an entry for NMISC too.
Approved by: neel (co-mentor)
'struct vmxctx'. It is preserved on the host stack across a guest entry
and exit and just restoring the host's '%rsp' is sufficient.
Pointed out by: grehan@
- remove redundant code
- remove erroneous setting of the error return
in vmmdev_ioctl()
- use style(9) initialization
- in vmx_inject_pir(), document the race condition
that the final conditional statement was detecting,
Tested with both gcc and clang builds.
Reviewed by: neel
correct for the pirbase test (since I'd have thought we'd need to do
something even when the offset is 0 and that test looks like a
misguided attempt to not use an uninitialized variable), but it is at
least the same as today.
My PCI RID changes somehow got intermixed with my PCI ARI patch when I
committed it. I may have accidentally applied a patch to a non-clean
working tree. Revert everything while I figure out what went wrong.
Pointy hat to: rstone
is already correctly reset to the FPU user save area, only PCB_KERNFPU
flag might leak from old thread state into the new state.
For creation of the user-mode thread, the change is nop since
corresponding syscall code does not use FPU. On the other hand,
creation of a kernel thread forks from a thread selected arbitrary
from proc0, which might use FPU.
Reported and tested by: Chris Torek <torek@torek.net>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
- When clearing a bit for a cpuid in pmap->pm_save, ensure that the
cpuid is not set in pm_active. The pm_save indicates which CPUs may
have cached translations for given PCID, which implies that a CPU
executing with the given pmap active have the translations
cached. [1]
- In smp_masked_invltlb(), pass pmap to smp_targeted_tlb_shootdown(). [1]
- In invlrng_handler(), check for the special values of pcid (0 and
-1) and do corresponding global or total invalidations before
checking for performing PCID-specific range invalidation with
INVPCID_ADDR. [2]
- In invltlb_pcid_handler(), do not read %cr3 unless needed. [2]
- Do minor style tweaks. [2]
Submitted by: Henrik Gulbrandsen <henrik@gulbra.net> [1]
Other parts sponsored by: The FreeBSD Foundation [2]
Tested by: Henrik Gulbrandsen, pho
MFC after: 1 week
With this change (and loader.efi from the projects/uefi branch) we can now
boot under qemu using the OVMF UEFI firmware image with the limitation
that a serial console is required.
(This is largely r246337 from the projects/uefi branch.)
Sponsored by: The FreeBSD Foundation
from any context i.e., it is not required to be called from a vcpu thread. The
ioctl simply sets a state variable 'vm->suspend' to '1' and returns.
The vcpus inspect 'vm->suspend' in the run loop and if it is set to '1' the
vcpu breaks out of the loop with a reason of 'VM_EXITCODE_SUSPENDED'. The
suspend handler waits until all 'vm->active_cpus' have transitioned to
'vm->suspended_cpus' before returning to userspace.
Discussed with: grehan
add it in kern.mk, but only if we're using clang. While this
option is supported by both clang and gcc, in the future there
may be changes to clang which change the defaults that require
a tweak to build our kernel such that other tools in our tree
will work. Set a good example by forcing -gdwarf-2 only for
clang builds, and only if the user hasn't specified another
dwarf level already. Update UPDATING to reflect the changed
state of affairs. This also keeps us from having to update
all the ARM kernels to add this, and also keeps us from
in the future having to update all the MIPS kernels and is
one less place the user will have to know to do something
special for clang and one less thing developers will need
to do when moving an architecture to clang.
Reviewed by: ian@
MFC after: 1 week
To reduce the diff struct pcu.cnt field was not renamed, so
PCPU_OP(cnt.field) is still used. pc_cnt and pcpu are also used in
kvm(3) and vmstat(8). The goal was to not affect externally used KPI.
Bump __FreeBSD_version_ in case some out-of-tree module/code relies on the
the global cnt variable.
Exp-run revealed no ports using it directly.
No objection from: arch@
Sponsored by: EMC / Isilon Storage Division
faults.
First, for accesses to direct map region should check for the limit by
which direct map is instantiated.
Second, for accesses to the kernel map, success returned from the
kernacc(9) does not guarantee that consequent attempt to read or write
to the checked address succeed, since other thread might invalidate
the address meantime. Add a new thread private flag TDP_DEVMEMIO,
which instructs vm_fault() to return error when fault happens on the
MAP_ENTRY_NOFAULT entry, instead of panicing. The trap handler would
then see a page fault from access, and recover in normal way, making
/dev/mem access safer.
Remove GIANT_REQUIRED from the amd64 memrw(), since it is not needed
and having Giant locked does not solve issues for amd64.
Note that at least the second issue exists on other architectures, and
requires similar patching for md code.
Reported and tested by: clusteradm (gjb, sbruno)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
called with interrupts enabled. Calling fasttrap_pid_probe() with interrupts
disabled can lead to deadlock if fasttrap writes to the process' address
space.
Reviewed by: rpaulo
MFC after: 3 weeks
blocked on it.
This is done by issuing a wakeup after clearing the 'vcpuid' from 'active_cpus'.
Also, use CPU_CLR_ATOMIC() to guarantee visibility of the updated 'active_cpus'
across all host cpus.
helps when bits and pieces of GENERIC from i386 or amd64 are cut and
pasted into other architecture's config files (which in the case of
ARM had gotten rather akimbo).
further refinement is required as some device drivers intended to be
portable over FreeBSD versions rely on __FreeBSD_version to decide whether
to include capability.h.
MFC after: 3 weeks
attributed if an ExtINT arrives during interrupt injection.
Also, fix a spurious interrupt if the PIC tries to raise an interrupt
before the outstanding one is accepted.
Finally, improve the PIC interrupt latency when another interrupt is
raised immediately after the outstanding one is accepted by creating a
vmexit rather than waiting for one to occur by happenstance.
Approved by: neel (co-mentor)
linking NIC Receive Side Scaling (RSS) to the network stack's
connection-group implementation. This prototype (and derived patches)
are in use at Juniper and several other FreeBSD-using companies, so
despite some reservations about its maturity, merge the patch to the
base tree so that it can be iteratively refined in collaboration rather
than maintained as a set of gradually diverging patch sets.
(1) Merge a software implementation of the Toeplitz hash specified in
RSS implemented by David Malone. This is used to allow suitable
pcbgroup placement of connections before the first packet is
received from the NIC. Software hashing is generally avoided,
however, due to high cost of the hash on general-purpose CPUs.
(2) In in_rss.c, maintain authoritative versions of RSS state intended
to be pushed to each NIC, including keying material, hash
algorithm/ configuration, and buckets. Provide software-facing
interfaces to hash 2- and 4-tuples for IPv4 and IPv6 using both
the RSS standardised Toeplitz and a 'naive' variation with a hash
efficient in software but with poor distribution properties.
Implement rss_m2cpuid()to be used by netisr and other load
balancing code to look up the CPU on which an mbuf should be
processed.
(3) In the Ethernet link layer, allow netisr distribution using RSS as
a source of policy as an alternative to source ordering; continue
to default to direct dispatch (i.e., don't try and requeue packets
for processing on the 'right' CPU if they arrive in a directly
dispatchable context).
(4) Allow RSS to control tuning of connection groups in order to align
groups with RSS buckets. If a packet arrives on a protocol using
connection groups, and contains a suitable hardware-generated
hash, use that hash value to select the connection group for pcb
lookup for both IPv4 and IPv6. If no hardware-generated Toeplitz
hash is available, we fall back on regular PCB lookup risking
contention rather than pay the cost of Toeplitz in software --
this is a less scalable but, at my last measurement, faster
approach. As core counts go up, we may want to revise this
strategy despite CPU overhead.
Where device drivers suitably configure NICs, and connection groups /
RSS are enabled, this should avoid both lock and line contention during
connection lookup for TCP. This commit does not modify any device
drivers to tune device RSS configuration to the global RSS
configuration; patches are in circulation to do this for at least
Chelsio T3 and Intel 1G/10G drivers. Currently, the KPI for device
drivers is not particularly robust, nor aware of more advanced features
such as runtime reconfiguration/rebalancing. This will hopefully prove
a useful starting point for refinement.
No MFC is scheduled as we will first want to nail down a more mature
and maintainable KPI/KBI for device drivers.
Sponsored by: Juniper Networks (original work)
Sponsored by: EMC/Isilon (patch update and merge)
AppleTalk was a network transport protocol for Apple Macintosh devices
in 80s and then 90s. Starting with Mac OS X in 2000 the AppleTalk was
a legacy protocol and primary networking protocol is TCP/IP. The last
Mac OS X release to support AppleTalk happened in 2009. The same year
routing equipment vendors (namely Cisco) end their support.
Thus, AppleTalk won't be supported in FreeBSD 11.0-RELEASE.
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
New ioctls VM_ISA_ASSERT_IRQ, VM_ISA_DEASSERT_IRQ and VM_ISA_PULSE_IRQ
can be used to manipulate the pic, and optionally the ioapic, pin state.
Reviewed by: jhb, neel
Approved by: neel (co-mentor)
AP startup on PVH follows the PV method, so we need to add a hook in
order to diverge from bare metal.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/machdep.c:
- Add hook for start_all_aps on native (using native_start_all_aps
defined in mp_machdep).
amd64/amd64/mp_machdep.c:
- Make some variables global because they will also be used by the
Xen PVH AP startup code.
- Use the start_all_aps hook to start APs.
- Rename start_all_aps to native_start_all_aps.
amd64/include/smp.h:
- Add declaration for native_start_all_aps.
x86/include/init.h:
- Declare start_all_aps hook in init_ops.
x86/xen/pv.c:
- Pick external declarations from mp_machdep.
- Introduce Xen PV code to start APs on PVH.
- Set start_all_aps init hook to use the Xen PVH implementation.
This hook will only be implemented for bare metal, Xen doesn't require
any bootstrap code since APs are started in long mode with paging
enabled.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/machdep.c:
- Set mp_bootaddress hook for bare metal.
x86/include/init.h:
- Define mp_bootaddress in init_ops.
Currently XEN (PV) and XENHVM (PVHVM) ports use different ways to
issue hypercalls, unify this by filling the hypercall_page under HVM
also.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/include/xen/hypercall.h:
- Unify Xen hypercall code by always using the PV way.
i386/i386/locore.s:
- Define hypercall_page on i386 XENHVM.
x86/xen/hvm.c:
- Fill hypercall_page on XENHVM kernels using the HVM method (only
when running as an HVM guest).
e820 memory map is fetched using a hypercall under Xen PVH, so add a
hook to init_ops in oder to diverge from bare metal and implement a
Xen variant.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
x86/include/init.h:
- Add a parse_memmap hook to init_ops, that will be called to fetch
and parse the memory map.
amd64/amd64/machdep.c:
- Decouple the fetch and the parse of the memmap, so the parse
function can be shared with Xen code.
- Move code around in order to implement the parse_memmap hook.
amd64/include/pc/bios.h:
- Declare bios_add_smap_entries (implemented in machdep.c).
x86/xen/pv.c:
- Implement fetching of e820 memmap when running as a PVH guest by
using the XENMEM_memory_map hypercall.
When running as a PVH guest, there's no emulated i8254, so we need to
use the Xen PV timer as the early source for DELAY. This change allows
for different implementations of the early DELAY function and
implements a Xen variant for it.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
dev/xen/timer/timer.c:
dev/xen/timer/timer.h:
- Implement Xen early delay functions using the PV timer and declare
them.
x86/include/init.h:
- Add hooks for early clock source initialization and early delay
functions.
i386/i386/machdep.c:
pc98/pc98/machdep.c:
amd64/amd64/machdep.c:
- Set early delay hooks to use the i8254 on bare metal.
- Use clock_init (that will in turn make use of init_ops) to
initialize the early clock source.
amd64/include/clock.h:
i386/include/clock.h:
- Declare i8254_delay and clock_init.
i386/xen/clock.c:
- Rename DELAY to i8254_delay.
x86/isa/clock.c:
- Introduce clock_init that will take care of initializing the early
clock by making use of the init_ops hooks.
- Move non ISA related delay functions to the newly introduced delay
file.
x86/x86/delay.c:
- Add moved delay related functions.
- Implement generic DELAY function that will use the init_ops hooks.
x86/xen/pv.c:
- Set PVH hooks for the early delay related functions in init_ops.
conf/files.amd64:
conf/files.i386:
conf/files.pc98:
- Add delay.c to the kernel build.
Add hooks to amd64 in order to have diverging implementations, since
on Xen PV the metadata is passed to the kernel in a different form.
Approbed by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/machdep.c:
- Define init_ops for native.
- Put native code inside of native_parse_preload_data hook.
- Call the parse_preload_data in order to fill the metadata info.
x86/include/init.h:
- Declare the init_ops struct.
x86/xen/pv.c:
- Declare xen_init_ops that contains the Xen PV implementation of
init_ops.
- Implement the parse_preload_data for Xen PVH, the info is fetched
from HYPERVISOR_start_info->cmd_line as provided by Xen.
Add the PV/PVH entry point and the low level functions for PVH
early initialization.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/genassym.c:
- Add __FreeBSD_version define to assym.s so it can be used for the
Xen notes.
amd64/amd64/locore.S:
- Make bootstack global so it can be used from Xen kernel entry
point.
amd64/amd64/xen-locore.S:
- Add Xen notes to the kernel.
- Add the Xen PV entry point, that is going to call hammer_time_xen.
amd64/include/asmacros.h:
- Add ELFNOTE macros.
i386/xen/xen_machdep.c:
- Define HYPERVISOR_start_info for the XEN i386 PV port, which is
going to be used in some shared code between PV and PVH.
x86/xen/hvm.c:
- Define HYPERVISOR_start_info for the PVH port.
x86/xen/pv.c:
- Introduce hammer_time_xen which is going to perform early setup for
Xen PVH:
- Setup shared Xen variables start_info, shared_info and
xen_store.
- Set guest type.
- Create initial page tables as FreeBSD expects to find them.
- Call into native init function (hammer_time).
xen/xen-os.h:
- Declare HYPERVISOR_start_info.
conf/files.amd64:
- Add amd64/amd64/locore.S and x86/xen/pv.c to the list of files.
Move asm IPIs handlers to C code, so both Xen and native IPI handlers
share the same code.
Reviewed by: jhb
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/apic_vector.S:
i386/i386/apic_vector.s:
- Remove asm coded IPI handlers and instead call the newly introduced
C variants.
amd64/amd64/mp_machdep.c:
i386/i386/mp_machdep.c:
- Add C coded clones to the asm IPI handlers (moved from
x86/xen/hvm.c).
i386/include/smp.h:
amd64/include/smp.h:
- Add prototypes for the C IPI handlers.
x86/xen/hvm.c:
- Move the C IPI handlers to mp_machdep and call those in the Xen IPI
handlers.
i386/xen/mp_machdep.c:
- Add dummy IPI handlers to the i386 Xen PV port (this port doesn't
support SMP).
There are a number of reports of userspace application crashes that
are "solved" by setting vm.pmap.pcid_enabled=0, including Java and the
x11/mate-terminal port (PR ports/184362).
I originally planned to disable this only in stable/10 (in r262753), but
it has been pointed out that additional crash reports on HEAD are not
likely to provide new insight into the problem. The feature can easily
be enabled for testing.
being updated outside of the vcpu_lock(). The race is benign and could
potentially result in a missed notification about a pending interrupt to
a vcpu. The interrupt would not be lost but rather delayed until the next
VM exit.
The vcpu's hostcpu is now updated concurrently with the vcpu state change.
When the vcpu transitions to the RUNNING state the hostcpu is set to 'curcpu'.
It is set to 'NOCPU' in all other cases.
Reviewed by: grehan
triggers a VM exit with the exit reason of an external interrupt but
without a valid interrupt set in the exit interrupt information.
Tested by: Michael Dexter
Reviewed by: neel
MFC after: 1 week
processor-specific VMCS or VMCB. The pending exception will be delivered right
before entering the guest.
The order of event injection into the guest is:
- hardware exception
- NMI
- maskable interrupt
In the Intel VT-x case, a pending NMI or interrupt will enable the interrupt
window-exiting and inject it as soon as possible after the hardware exception
is injected. Also since interrupts are inherently asynchronous, injecting
them after the hardware exception should not affect correctness from the
guest perspective.
Rename the unused ioctl VM_INJECT_EVENT to VM_INJECT_EXCEPTION and restrict
it to only deliver x86 hardware exceptions. This new ioctl is now used to
inject a protection fault when the guest accesses an unimplemented MSR.
Discussed with: grehan, jhb
Reviewed by: jhb
This brings in the "-w" option from bhyve to ignore unknown MSRs.
It will make debugging Linux guests a bit easier.
Suggested by: Willem Jan Withagen (wjw at digiware nl)
processor family to determine if the workaround for AMD Family 10h Erratum
383 should be enabled. To enable virtual machine migration among a
heterogeneous collection of physical machines, the hypervisor may have
been configured to report an older processor family with a reduced feature
set. Effectively, the reported processor family and its features are like
a "least common denominator" for the collection of machines.
Therefore, when the kernel is running in a virtual machine, instead of
relying upon the processor family, we now test for features that prove
that the underlying processor is not affected by the erratum. (The
features that we test for are unlikely to ever be emulated in software
on an affected physical processor.)
PR: 186061
Tested by: Simon Matter
Discussed with: jhb, neel
MFC after: 2 weeks
The vlapic.ops handler 'enable_x2apic_mode' is called when the vlapic mode
is switched to x2APIC. The VT-x implementation of this handler turns off the
APIC-access virtualization and enables the x2APIC virtualization in the VMCS.
The x2APIC virtualization is done by allowing guest read access to a subset
of MSRs in the x2APIC range. In non-root operation the processor will satisfy
an 'rdmsr' access to these MSRs by reading from the virtual APIC page instead.
The guest is also given write access to TPR, EOI and SELF_IPI MSRs which
get special treatment in non-root operation. This is documented in the
Intel SDM section titled "Virtualizing MSR-Based APIC Accesses".
Enforce that APIC-write and APIC-access VM-exits are handled only if
APIC-access virtualization is enabled. The one exception to this is
SELF_IPI virtualization which may result in an APIC-write VM-exit.
simplify the implementation of the x2APIC virtualization assist in VT-x.
Prior to this change the vlapic allowed the guest to change its mode from
xAPIC to x2APIC. We don't allow that any more and the vlapic mode is locked
when the virtual machine is created. This is not very constraining because
operating systems already have to deal with BIOS setting up the APIC in
x2APIC mode at boot.
Fix a bug in the CPUID emulation where the x2APIC capability was leaking
from the host to the guest.
Ignore MMIO reads and writes to the vlapic in x2APIC mode. Similarly, ignore
MSR accesses to the vlapic when it is in xAPIC mode.
The default configuration of the vlapic is xAPIC. The "-x" option to bhyve(8)
can be used to change the mode to x2APIC instead.
Discussed with: grehan@
emulated instructions.
- Add helper routines to inject interrupt information for a hardware
exception from the VM exit callback routines.
- Use the new routines to inject GP and UD exceptions for invalid
operations when emulating the xsetbv instruction.
- Don't directly manipulate the entry interrupt info when a user event
is injected. Instead, store the event info in the vmx state and
only apply it during a VM entry if a hardware exception or NMI is
not already pending.
- While here, use HANDLED/UNHANDLED instead of 1/0 in a couple of
routines.
Reviewed by: neel
in x2apic mode. Reads to this MSR are currently ignored but should cause a
general proctection exception to be injected into the vcpu.
All accesses to the corresponding offset in xAPIC mode are ignored.
Also, do not panic the host if there is mismatch between the trigger mode
programmed in the TMR and the actual interrupt being delivered. Instead the
anomaly is logged to aid debugging and to prevent a misbehaving guest from
panicking the host.
This is necessary because if the vlapic is configured in x2apic mode the
vioapic_process_eoi() function is called inside the critical section
established by vm_run().
all of the features in the current working draft of the upcoming C++
standard, provisionally named C++1y.
The code generator's performance is greatly increased, and the loop
auto-vectorizer is now enabled at -Os and -O2 in addition to -O3. The
PowerPC backend has made several major improvements to code generation
quality and compile time, and the X86, SPARC, ARM32, Aarch64 and SystemZ
backends have all seen major feature work.
Release notes for llvm and clang can be found here:
<http://llvm.org/releases/3.4/docs/ReleaseNotes.html>
<http://llvm.org/releases/3.4/tools/clang/docs/ReleaseNotes.html>
MFC after: 1 month
I/O windows, the default is to preserve the firmware-assigned resources.
PCI bus numbers are only managed if NEW_PCIB is enabled and the architecture
defines a PCI_RES_BUS resource type.
- Add a helper API to create top-level PCI bus resource managers for each
PCI domain/segment. Host-PCI bridge drivers use this API to allocate
bus numbers from their associated domain.
- Change the PCI bus and CardBus drivers to allocate a bus resource for
their bus number from the parent PCI bridge device.
- Change the PCI-PCI and PCI-CardBus bridge drivers to allocate the
full range of bus numbers from secbus to subbus from their parent bridge.
The drivers also always program their primary bus register. The bridge
drivers also support growing their bus range by extending the bus resource
and updating subbus to match the larger range.
- Add support for managing PCI bus resources to the Host-PCI bridge drivers
used for amd64 and i386 (acpi_pcib, mptable_pcib, legacy_pcib, and qpi_pcib).
- Define a PCI_RES_BUS resource type for amd64 and i386.
Reviewed by: imp
MFC after: 1 month
reuse the first page of the crashdumpmap as CMAP1/CADDR1. For i386,
remove CMAP1/CADDR1 entirely and reuse CMAP3/CADDR3 for the memory test.
Reviewed by: alc, peter
MFC after: 2 weeks
XSAVE-enabled features like AVX.
- Store a per-cpu guest xcr0 register. When switching to the guest FPU
state, switch to the guest xcr0 value. Note that the guest FPU state is
saved and restored using the host's xcr0 value and xcr0 is saved/restored
"inside" of saving/restoring the guest FPU state.
- Handle VM exits for the xsetbv instruction by updating the guest xcr0.
- Expose the XSAVE feature to the guest only if the host has enabled XSAVE,
and only advertise XSAVE features enabled by the host to the guest.
This ensures that the guest will only adjust FPU state that is a subset
of the guest FPU state saved and restored by the host.
Reviewed by: grehan
If a VM-exit is caused by an NMI then "blocking by NMI" is in effect on the
CPU when the VM-exit is completed. No more NMIs will be recognized until
the execution of an "iret".
Prior to this change the NMI handler was dispatched via a software interrupt
with interrupts enabled. This meant that an interrupt could be recognized
by the processor before the NMI handler completed its execution. The "iret"
issued by the interrupt handler would then cause the "blocking by NMI" to
be cleared prematurely.
This is now fixed by handling the NMI with interrupts disabled in addition
to "blocking by NMI" already established by the VM-exit.
- Similar to the hack for bootinfo32.c in userboot, define
_MACHINE_ELF_WANT_32BIT in the load_elf32 file handlers in userboot.
This allows userboot to load 32-bit kernels and modules.
- Copy the SMAP generation code out of bootinfo64.c and into its own
file so it can be shared with bootinfo32.c to pass an SMAP to the i386
kernel.
- Use uint32_t instead of u_long when aligning module metadata in
bootinfo32.c in userboot, as otherwise the metadata used 64-bit
alignment which corrupted the layout.
- Populate the basemem and extmem members of the bootinfo struct passed
to 32-bit kernels.
- Fix the 32-bit stack in userboot to start at the top of the stack
instead of the bottom so that there is room to grow before the
kernel switches to its own stack.
- Push a fake return address onto the 32-bit stack in addition to the
arguments normally passed to exec() in the loader. This return
address is needed to convince recover_bootinfo() in the 32-bit
locore code that it is being invoked from a "new" boot block.
- Add a routine to libvmmapi to setup a 32-bit flat mode register state
including a GDT and TSS that is able to start the i386 kernel and
update bhyveload to use it when booting an i386 kernel.
- Use the guest register state to determine the CPU's current instruction
mode (32-bit vs 64-bit) and paging mode (flat, 32-bit, PAE, or long
mode) in the instruction emulation code. Update the gla2gpa() routine
used when fetching instructions to handle flat mode, 32-bit paging, and
PAE paging in addition to long mode paging. Don't look for a REX
prefix when the CPU is in 32-bit mode, and use the detected mode to
enable the existing 32-bit mode code when decoding the mod r/m byte.
Reviewed by: grehan, neel
MFC after: 1 month
- Convert VMM_CTR to VCPU_CTR KTR macros
- Special handling of halt, save rflags for VMM layer to emulate
halt for vcpu(sleep to be awakened by interrupt or stop it)
- Cleanup of RVI exit handling code
Submitted by: Anish Gupta (akgupt3@gmail.com)
Reviewed by: grehan
Prior to this change the cached value of 'pm_eptgen' was tracked per-vcpu
and per-hostcpu. In the degenerate case where 'N' vcpus were sharing
a single hostcpu this could result in 'N - 1' unnecessary TLB invalidations.
Since an 'invept' invalidates mappings for all VPIDs the first 'invept'
is sufficient.
Fix this by moving the 'eptgen[MAXCPU]' array from 'vmxctx' to 'struct vmx'.
If it is known that an 'invept' is going to be done before entering the
guest then it is safe to skip the 'invvpid'. The stat VPU_INVVPID_SAVED
counts the number of 'invvpid' invalidations that were avoided because
they were subsumed by an 'invept'.
Discussed with: grehan
the virtio backends.
- Add a new ioctl to export the count of pins on the I/O APIC from vmm
to the hypervisor.
- Use pins on the I/O APIC >= 16 for PCI interrupts leaving 0-15 for
ISA interrupts.
- Populate the MP Table with I/O interrupt entries for any PCI INTx
interrupts.
- Create a _PRT table under the PCI root bridge in ACPI to route any
PCI INTx interrupts appropriately.
- Track which INTx interrupts are in use per-slot so that functions
that share a slot attempt to distribute their INTx interrupts across
the four available pins.
- Implicitly mask INTx interrupts if either MSI or MSI-X is enabled
and when the INTx DIS bit is set in a function's PCI command register.
Either assert or deassert the associated I/O APIC pin when the
state of one of those conditions changes.
- Add INTx support to the virtio backends.
- Always advertise the MSI capability in the virtio backends.
Submitted by: neel (7)
Reviewed by: neel
MFC after: 2 weeks
The VMCS field EOI_bitmap[] is an array of 256 bits - one for each vector.
If a bit is set to '1' in the EOI_bitmap[] then the processor will trigger
an EOI-induced VM-exit when it is doing EOI virtualization.
The EOI-induced VM-exit results in the EOI being forwarded to the vioapic
so that level triggered interrupts can be properly handled.
Tested by: Anish Gupta (akgupt3@gmail.com)
injected into the vcpu but the VM-entry interruption information field
already has the valid bit set.
Pointed out by: David Reed (david.reed@tidalscale.com)
via a software interrupt.
This is safe to do because the logical processor is already cognizant of the
NMI and further NMIs are blocked until the host's NMI handler executes "iret".
the Guest Interruptibility-state field. However, there isn't any way to
figure out which processors have this requirement.
So, inject a pending NMI only if NMI_BLOCKING, MOVSS_BLOCKING, STI_BLOCKING
are all clear. If any of these bits are set then enable "NMI window exiting"
and inject the NMI in the VM-exit handler.
in the Guest Interruptibility-state VMCS field.
If we fail to do this then a subsequent VM-entry will fail because it is an
error to inject an NMI into the guest while "NMI Blocking" is turned on. This
is described in "Checks on Guest Non-Register State" in the Intel SDM.
Submitted by: David Reed (david.reed@tidalscale.com)
can be initiated in the context of a vcpu thread or from the bhyve(8) control
process.
The first use of this functionality is to update the vlapic trigger-mode
register when the IOAPIC pin configuration is changed.
Prior to this change we would update the TMR in the virtual-APIC page at
the time of interrupt delivery. But this doesn't work with Posted Interrupts
because there is no way to program the EOI_exit_bitmap[] in the VMCS of
the target at the time of interrupt delivery.
Discussed with: grehan@
inject interrupts into the guest without causing a VM-exit.
This feature can be disabled by setting the tunable "hw.vmm.vmx.use_apic_pir"
to "0".
The following sysctls provide information about this feature:
- hw.vmm.vmx.posted_interrupts (0 if disabled, 1 if enabled)
- hw.vmm.vmx.posted_interrupt_vector (vector number used for vcpu notification)
Tested on a Intel Xeon E5-2620v2 courtesy of Allan Jude at ScaleEngine.
This control is needed to enable "Posted Interrupts" and is present in all
the Intel VT-x implementations supported by bhyve so enable it as the default.
With this VM-exit control enabled the processor will acknowledge the APIC and
store the vector number in the "VM-Exit Interruption Information" field. We
now call the interrupt handler "by hand" through the IDT entry associated
with the vector.
hardware. It is possible to turn this feature off and fall back to software
emulation of the APIC by setting the tunable hw.vmm.vmx.use_apic_vid to 0.
We now start handling two new types of VM-exits:
APIC-access: This is a fault-like VM-exit and is triggered when the APIC
register access is not accelerated (e.g. apic timer CCR). In response to
this we do emulate the instruction that triggered the APIC-access exit.
APIC-write: This is a trap-like VM-exit which does not require any instruction
emulation but it does require the hypervisor to emulate the access to the
specified register (e.g. icrlo register).
Introduce 'vlapic_ops' which are function pointers to vector the various
vlapic operations into processor-dependent code. The 'Virtual Interrupt
Delivery' feature installs 'ops' for setting the IRR bits in the virtual
APIC page and to return whether any interrupts are pending for this vcpu.
Tested on an "Intel Xeon E5-2620 v2" courtesy of Allan Jude at ScaleEngine.
Keep a copy of the 'rip' and the 'exit_reason' and use that when calling
vmx_exit_trace(). This is because both the 'rip' and 'exit_reason' can
be changed by 'vmx_exit_process()' and can lead to very misleading traces.
the vcpu should be kicked to process a pending interrupt. This will be useful
in the implementation of the Posted Interrupt APICv feature.
Change the return value of 'vlapic_pending_intr()' to indicate whether or not
an interrupt is available to be delivered to the vcpu depending on the value
of the PPR.
Add KTR tracepoints to debug guest IPI delivery.
'vmx_vminit()' that does customization.
This makes it easier to turn on optional features (e.g. APICv) without
having to keep adding new parameters to 'vmcs_set_defaults()'.
Reviewed by: grehan@
guest disables the HPET.
The HPET timer interrupt is triggered from the callout handler associated with
the timer. It is possible for the callout handler to be delayed before it gets
a chance to execute. If the guest disables the HPET during this window then the
handler never gets a chance to execute and the timer interrupt is lost.
This is now fixed by injecting a timer interrupt into the guest if the callout
time is detected to be in the past when the HPET is disabled.
times [1]. Assert that the pmap passed to pmap_remove_pages() is only
active on current CPU.
Submitted by: alc [1]
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
hides the setjmp/longjmp semantics of VM enter/exit. vmx_enter_guest() is used
to enter guest context and vmx_exit_guest() is used to transition back into
host context.
Fix a longstanding race where a vcpu interrupt notification might be ignored
if it happens after vmx_inject_interrupts() but before host interrupts are
disabled in vmx_resume/vmx_launch. We now called vmx_inject_interrupts() with
host interrupts disabled to prevent this.
Suggested by: grehan@
The handler is now called after the register value is updated in the virtual
APIC page. This will make it easier to handle APIC-write VM-exits with APIC
register virtualization turned on.
This also implies that we need to keep a snapshot of the last value written
to a LVT register. We can no longer rely on the LVT registers in the APIC
page to be "clean" because the guest can write anything to it before the
hypervisor has had a chance to sanitize it.
registers.
The handler is now called after the register value is updated in the virtual
APIC page. This will make it easier to handle APIC-write VM-exits with APIC
register virtualization turned on.
We can no longer rely on the value of 'icr_timer' on the APIC page
in the callout handler. With APIC register virtualization the value of
'icr_timer' will be updated by the processor in guest-context before an
APIC-write VM-exit.
Clear the 'delivery status' bit in the ICRLO register in the write handler.
With APIC register virtualization the write happens in guest-context and
we cannot prevent a (buggy) guest from setting this bit.
The handler is now called after the register value is updated in the virtual
APIC page. This will make it easier to handle APIC-write VM-exits with APIC
register virtualization turned on.
Additionally, mask all the LVT entries when the vlapic is software-disabled.
The handlers are now called after the register value is updated in the virtual
APIC page. This will make it easier to handle APIC-write VM-exits with APIC
register virtualization turned on.
Additionally, we need to ensure that the value of these registers is always
correctly reflected in the virtual APIC page, because there is no VM exit
when the guest reads these registers with APIC register virtualization.
emulation.
The vlapic initialization and cleanup is done via processor specific vmm_ops.
This will allow the VT-x/SVM modules to layer any hardware-assist for APIC
emulation or virtual interrupt delivery on top of the vlapic device model.
Add a parameter to 'vcpu_notify_event()' to distinguish between vlapic
interrupts versus other events (e.g. NMI). This provides an opportunity to
use hardware-assists like Posted Interrupts (VT-x) or doorbell MSR (SVM)
to deliver an interrupt to a guest without causing a VM-exit.
Get rid of lapic_pending_intr() and lapic_intr_accepted() and use the
vlapic_xxx() counterparts directly.
Associate an 'Apic Page' with each vcpu and reference it from the 'vlapic'.
The 'Apic Page' is intended to be referenced from the Intel VMCS as the
'virtual APIC page' or from the AMD VMCB as the 'vAPIC backing page'.
- Add a generic routine to trigger an LVT interrupt that supports both
fixed and NMI delivery modes.
- Add an ioctl and bhyvectl command to trigger local interrupts inside a
guest. In particular, a global NMI similar to that raised by SERR# or
PERR# can be simulated by asserting LINT1 on all vCPUs.
- Extend the LVT table in the vCPU local APIC to support CMCI.
- Flesh out the local APIC error reporting a bit to cache errors and
report them via ESR when ESR is written to. Add support for asserting
the error LVT when an error occurs. Raise illegal vector errors when
attempting to signal an invalid vector for an interrupt or when sending
an IPI.
- Ignore writes to reserved bits in LVT entries.
- Export table entries the MADT and MP Table advertising the stock x86
config of LINT0 set to ExtInt and LINT1 wired to NMI.
Reviewed by: neel (earlier version)
state before the requested state transition. This guarantees that there is
exactly one ioctl() operating on a vcpu at any point in time and prevents
unintended state transitions.
More details available here:
http://lists.freebsd.org/pipermail/freebsd-virtualization/2013-December/001825.html
Reviewed by: grehan
Reported by: Markiyan Kushnir (markiyan.kushnir at gmail.com)
MFC after: 3 days
The least significant 8 bits of 'pm_flags' are now used for the IPI vector
to use for nested page table TLB shootdown.
Previously we used IPI_AST to interrupt the host cpu which is functionally
correct but could lead to misleading interrupt counts for AST handler. The
AST handler was also doing a lot more than what is required for the nested
page table TLB shootdown (EOI and IRET).
- No emulation of A/D bits is required since AMD-V RVI
supports A/D bits.
- Enable pmap PT_RVI support(w/o PAT) which is required for
memory over-commit support.
- Other minor fixes:
* Make use of VMCB EXITINTINFO field. If a #VMEXIT happens while
delivering an interrupt, EXITINTINFO has all the details that bhyve
needs to inject the same interrupt.
* SVM h/w decode assist code was incomplete - removed for now.
* Some minor code clean-up (more coming).
Submitted by: Anish Gupta (akgupt3@gmail.com)
callers treat the MSI 'addr' and 'data' fields as opaque and also lets
bhyve implement multiple destination modes: physical, flat and clustered.
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
Reviewed by: grehan@
When the guest is bringing up the APs in the x2APIC mode a write to the
ICR register will now trigger a return to userspace with an exitcode of
VM_EXITCODE_SPINUP_AP. This gets SMP guests working again with x2APIC.
Change the vlapic timer lock to be a spinlock because the vlapic can be
accessed from within a critical section (vm run loop) when guest is using
x2apic mode.
Reviewed by: grehan@
This decouples the guest's 'hz' from the host's 'hz' setting. For e.g. it is
now possible to have a guest run at 'hz=1000' while the host is at 'hz=100'.
Discussed with: grehan@
Tested by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
vcpu and destroy its thread context. Also modify the 'HLT' processing to ignore
pending interrupts in the IRR if interrupts have been disabled by the guest.
The interrupt cannot be injected into the guest in any case so resuming it
is futile.
With this change "halt" from a Linux guest works correctly.
Reviewed by: grehan@
Tested by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
has outgrown its original name. Originally this function simply sent an IPI
to the host cpu that a vcpu was executing on but now it does a lot more than
just that.
Reviewed by: grehan@
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
requires process descriptors to work and having PROCDESC in GENERIC
seems not enough, especially that we hope to have more and more consumers
in the base.
MFC after: 3 days
commit level triggered interrupts would work as long as the pin was not shared
among multiple interrupt sources.
The vlapic now keeps track of level triggered interrupts in the trigger mode
register and will forward the EOI for a level triggered interrupt to the
vioapic. The vioapic in turn uses the EOI to sample the level on the pin and
re-inject the vector if the pin is still asserted.
The vhpet is the first consumer of level triggered interrupts and advertises
that it can generate interrupts on pins 20 through 23 of the vioapic.
Discussed with: grehan@
compilation results in inclusion of the header, a confict arises due
to savefpu being union for i386, but used as struct in the pcb
definition. The 32bit code should not need amd64 variant of the
struct pcb anyway.
For struct region_descriptor, use __uint64_t instead of unsigned long,
as the base type for bit-fields. Unsigned long cannot have width 64
for -m32.
The changes allowed to use sys/sysctl.h for cc -m32.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
bhyve supports a single timer block with 8 timers. The timers are all 32-bit
and capable of being operated in periodic mode. All timers support interrupt
delivery using MSI. Timers 0 and 1 also support legacy interrupt routing.
At the moment the timers are not connected to any ioapic pins but that will
be addressed in a subsequent commit.
This change is based on a patch from Tycho Nightingale (tycho.nightingale@pluribusnetworks.com).
option, unbreak the lock tracing release semantic by embedding
calls to LOCKSTAT_PROFILE_RELEASE_LOCK() direclty in the inlined
version of the releasing functions for mutex, rwlock and sxlock.
Failing to do so skips the lockstat_probe_func invokation for
unlocking.
- As part of the LOCKSTAT support is inlined in mutex operation, for
kernel compiled without lock debugging options, potentially every
consumer must be compiled including opt_kdtrace.h.
Fix this by moving KDTRACE_HOOKS into opt_global.h and remove the
dependency by opt_kdtrace.h for all files, as now only KDTRACE_FRAMES
is linked there and it is only used as a compile-time stub [0].
[0] immediately shows some new bug as DTRACE-derived support for debug
in sfxge is broken and it was never really tested. As it was not
including correctly opt_kdtrace.h before it was never enabled so it
was kept broken for a while. Fix this by using a protection stub,
leaving sfxge driver authors the responsibility for fixing it
appropriately [1].
Sponsored by: EMC / Isilon storage division
Discussed with: rstone
[0] Reported by: rstone
[1] Discussed with: philip
to inject edge triggered legacy interrupts into the guest.
Start using the new API in device models that use edge triggered interrupts:
viz. the 8254 timer and the LPC/uart device emulation.
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
Extracted from the projects/uefi branch, this change is a reasonable
cleanup and will reduce the diffs to review when bringing in the
UEFI work.
Reviewed by: kib@
Sponsored by: The FreeBSD Foundation
The page presence memory test takes a long time on large memory systems
and has little value on contemporary amd64 hardware.
Sponsored by: The FreeBSD Foundation
sys/i386/i386/machdep.c:
sys/amd64/amd64/machdep.c:
The value reported by FreeBSD as "real memory" when booting
doesn't match what is later reported by sysctl as hw.realmem.
This is due to the fact that the value printed during the
boot process is fetched from smbios data (when possible),
and accounts for holes in physical memory. On the other
hand, the value of hw.realmem is unconditionally set to be
one larger than the highest page of the physical address
space.
Fix this by setting hw.realmem to the same value printed
during boot, this makes hw.realmem honour it's name and
account properly for physical memory present in the system.
Submitted by: Roger Pau Monné
Reviewed by: gibbs
Debuggers may need to change PSL_RF. Note that tf_eflags is already stored
in the signal context during signal handling and PSL_RF previously could be
modified via sigreturn, so this change should not provide any new ability
to userspace.
For background see the thread at:
http://lists.freebsd.org/pipermail/freebsd-i386/2007-September/005910.html
Reviewed by: jhb, kib
Sponsored by: DARPA, AFRL
upcoming in-kernel device emulations like the HPET.
The ioctls VM_IOAPIC_ASSERT_IRQ and VM_IOAPIC_DEASSERT_IRQ are used to
manipulate the ioapic pin state.
Discussed with: grehan@
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
described in the rev. 3.0 of the Kabini BKDG, document 48751.pdf.
Partially based on the patch submitted by: Dmitry Luhtionov <dmitryluhtionov@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
words, every architecture is now auto-sizing the kmem arena. This revision
changes kmeminit() so that the definition of VM_KMEM_SIZE_SCALE becomes
mandatory and the definition of VM_KMEM_SIZE becomes optional.
Replace or eliminate all existing definitions of VM_KMEM_SIZE. With
auto-sizing enabled, VM_KMEM_SIZE effectively became an alternate spelling
for VM_KMEM_SIZE_MIN on most architectures. Use VM_KMEM_SIZE_MIN for
clarity.
Change kmeminit() so that the effect of defining VM_KMEM_SIZE is similar to
that of setting the tunable vm.kmem_size. Whereas the macros
VM_KMEM_SIZE_{MAX,MIN,SCALE} have had the same effect as the tunables
vm.kmem_size_{max,min,scale}, the effects of VM_KMEM_SIZE and vm.kmem_size
have been distinct. In particular, whereas VM_KMEM_SIZE was overridden by
VM_KMEM_SIZE_{MAX,MIN,SCALE} and vm.kmem_size_{max,min,scale}, vm.kmem_size
was not. Remedy this inconsistency. Now, VM_KMEM_SIZE can be used to set
the size of the kmem arena at compile-time without that value being
overridden by auto-sizing.
Update the nearby comments to reflect the kmem submap being replaced by the
kmem arena. Stop duplicating the auto-sizing formula in every machine-
dependent vmparam.h and place it in kmeminit() where auto-sizing takes
place.
Reviewed by: kib (an earlier version)
Sponsored by: EMC / Isilon Storage Division
in the kernel. This abstraction was redundant because the only device emulated
inside vmm.ko is the local apic and it is always at a fixed guest physical
address.
Discussed with: grehan
corresponding x86 trap type. Userland DTrace probes are currently handled
by the other fasttrap hooks (dtrace_pid_probe_ptr and
dtrace_return_probe_ptr).
Discussed with: rpaulo
1.3 of Intelб╝ Virtualization Technology for Directed I/O Architecture
Specification. The Extended Context and PASIDs from the rev. 2.2 are
not supported, but I am not aware of any released hardware which
implements them. Code does not use queued invalidation, see comments
for the reason, and does not provide interrupt remapping services.
Code implements the management of the guest address space per domain
and allows to establish and tear down arbitrary mappings, but not
partial unmapping. The superpages are created as needed, but not
promoted. Faults are recorded, fault records could be obtained
programmatically, and printed on the console.
Implement the busdma(9) using DMARs. This busdma backend avoids
bouncing and provides security against misbehaving hardware and driver
bad programming, preventing leaks and corruption of the memory by wild
DMA accesses.
By default, the implementation is compiled into amd64 GENERIC kernel
but disabled; to enable, set hw.dmar.enable=1 loader tunable. Code is
written to work on i386, but testing there was low priority, and
driver is not enabled in GENERIC. Even with the DMAR turned on,
individual devices could be directed to use the bounce busdma with the
hw.busdma.pci<domain>:<bus>:<device>:<function>.bounce=1 tunable. If
DMARs are capable of the pass-through translations, it is used,
otherwise, an identity-mapping page table is constructed.
The driver was tested on Xeon 5400/5500 chipset legacy machine,
Haswell desktop and E5 SandyBridge dual-socket boxes, with ahci(4),
ata(4), bce(4), ehci(4), mfi(4), uhci(4), xhci(4) devices. It also
works with em(4) and igb(4), but there some fixes are needed for
drivers, which are not committed yet. Intel GPUs do not work with
DMAR (yet).
Many thanks to John Baldwin, who explained me the newbus integration;
Peter Holm, who did all testing and helped me to discover and
understand several incredible bugs; and to Jim Harris for the access
to the EDS and BWG and for listening when I have to explain my
findings to somebody.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
In report_progress(), use nitems(progress_track) instead of manually
hard-coding array size. Wrap long line.
In blk_write(), code verifies that ptr and pa cannot be non-zero
simultaneously. The later check for the page-alignment of the ptr
argument never triggers due to pa != 0 always implying ptr == NULL. I
believe that the intent was to ensure that physicall address passed is
page-aligned, since the address is (temporary) mapped for the duration
of the page write.
Clear the progress_track.visited fields when starting minidump. If
minidump is restarted or taken second time during the system lifetime,
progress is not printed otherwise, making operator suspectible to the
dump status.
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
all vcpus belonging to a guest. This means that when different vcpus belonging
to the same guest are executing on the same host cpu there may be "leakage"
in the mappings created by one vcpu to another.
The proper fix for this is being worked on and will be committed shortly.
In the meantime workaround this bug by flushing the guest TLB entries on every
VM entry.
Submitted by: Anish Gupta (akgupt3@gmail.com)
'invpcid' instruction to the guest. Currently bhyve will try to enable this
capability unconditionally if it is available.
Consolidate code in bhyve to set the capabilities so it is no longer
duplicated in BSP and AP bringup.
Add a sysctl 'vm.pmap.invpcid_works' to display whether the 'invpcid'
instruction is available.
Reviewed by: grehan
MFC after: 3 days
hang on console output (due to a missing interrupt).
SVM does exit processing and then handles ASTPENDING which
overwrites the already handled SVM exit cause and corrupts
virtual machine state. For example, if the SVM exit was due to
an I/O port access but the main loop detected an ASTPENDING,
the exit would be processed as ASTPENDING and leave the
device (e.g. emulated UART) for that I/O port in bad state.
Submitted by: Anish Gupta (akgupt3@gmail.com)
Reviewed by: grehan
the 'vmmdev_mtx' in vmmdev_rw().
Rely on the 'si_threadcount' accounting to ensure that we never destroy the
VM device node while it has operations in progress (e.g. ioctl, mmap etc).
Reported by: grehan
Reviewed by: grehan
field. Perform vcpu enumeration for Xen PV and HVM environments
and convert all Xen drivers to use vcpu_id instead of a hard coded
assumption of the mapping algorithm (acpi or apic ID) in use.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (blanket Xen)
amd64/include/pcpu.h:
i386/include/pcpu.h:
Add vcpu_id to the amd64 and i386 pcpu structures.
dev/xen/timer/timer.c
x86/xen/xen_intr.c
Use new vcpu_id instead of assuming acpi_id == vcpu_id.
i386/xen/mp_machdep.c:
i386/xen/mptable.c
x86/xen/hvm.c:
Perform Xen HVM and Xen full PV vcpu_id mapping.
x86/xen/hvm.c:
x86/acpica/madt.c
Change SYSINIT ordering of acpi CPU enumeration so that it
is guaranteed to be available at the time of Xen HVM vcpu
id mapping.
Make the amd64/pmap code aware of nested page table mappings used by bhyve
guests. This allows bhyve to associate each guest with its own vmspace and
deal with nested page faults in the context of that vmspace. This also
enables features like accessed/dirty bit tracking, swapping to disk and
transparent superpage promotions of guest memory.
Guest vmspace:
Each bhyve guest has a unique vmspace to represent the physical memory
allocated to the guest. Each memory segment allocated by the guest is
mapped into the guest's address space via the 'vmspace->vm_map' and is
backed by an object of type OBJT_DEFAULT.
pmap types:
The amd64/pmap now understands two types of pmaps: PT_X86 and PT_EPT.
The PT_X86 pmap type is used by the vmspace associated with the host kernel
as well as user processes executing on the host. The PT_EPT pmap is used by
the vmspace associated with a bhyve guest.
Page Table Entries:
The EPT page table entries as mostly similar in functionality to regular
page table entries although there are some differences in terms of what
bits are used to express that functionality. For e.g. the dirty bit is
represented by bit 9 in the nested PTE as opposed to bit 6 in the regular
x86 PTE. Therefore the bitmask representing the dirty bit is now computed
at runtime based on the type of the pmap. Thus PG_M that was previously a
macro now becomes a local variable that is initialized at runtime using
'pmap_modified_bit(pmap)'.
An additional wrinkle associated with EPT mappings is that older Intel
processors don't have hardware support for tracking accessed/dirty bits in
the PTE. This means that the amd64/pmap code needs to emulate these bits to
provide proper accounting to the VM subsystem. This is achieved by using
the following mapping for EPT entries that need emulation of A/D bits:
Bit Position Interpreted By
PG_V 52 software (accessed bit emulation handler)
PG_RW 53 software (dirty bit emulation handler)
PG_A 0 hardware (aka EPT_PG_RD)
PG_M 1 hardware (aka EPT_PG_WR)
The idea to use the mapping listed above for A/D bit emulation came from
Alan Cox (alc@).
The final difference with respect to x86 PTEs is that some EPT implementations
do not support superpage mappings. This is recorded in the 'pm_flags' field
of the pmap.
TLB invalidation:
The amd64/pmap code has a number of ways to do invalidation of mappings
that may be cached in the TLB: single page, multiple pages in a range or the
entire TLB. All of these funnel into a single EPT invalidation routine called
'pmap_invalidate_ept()'. This routine bumps up the EPT generation number and
sends an IPI to the host cpus that are executing the guest's vcpus. On a
subsequent entry into the guest it will detect that the EPT has changed and
invalidate the mappings from the TLB.
Guest memory access:
Since the guest memory is no longer wired we need to hold the host physical
page that backs the guest physical page before we can access it. The helper
functions 'vm_gpa_hold()/vm_gpa_release()' are available for this purpose.
PCI passthru:
Guest's with PCI passthru devices will wire the entire guest physical address
space. The MMIO BAR associated with the passthru device is backed by a
vm_object of type OBJT_SG. An IOMMU domain is created only for guest's that
have one or more PCI passthru devices attached to them.
Limitations:
There isn't a way to map a guest physical page without execute permissions.
This is because the amd64/pmap code interprets the guest physical mappings as
user mappings since they are numerically below VM_MAXUSER_ADDRESS. Since PG_U
shares the same bit position as EPT_PG_EXECUTE all guest mappings become
automatically executable.
Thanks to Alan Cox and Konstantin Belousov for their rigorous code reviews
as well as their support and encouragement.
Thanks for John Baldwin for reviewing the use of OBJT_SG as the backing
object for pci passthru mmio regions.
Special thanks to Peter Holm for testing the patch on short notice.
Approved by: re
Discussed with: grehan
Reviewed by: alc, kib
Tested by: pho
page, otherwise the small mappings loop would use uninitialized value.
Note that currently pmap_clear_modify() is not called for fictitious
pages.
Sponsored by: The FreeBSD Foundation
Approved by: re (glebius)
registers, to make the restarted syscall instruction pass the correct
arguments.
PR: kern/182161
Reported by: Russ Cox <rsc@swtch.com>
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
Approved by: re (marius)
semblance of API stability and growth during the 10.* timeframe.
Userland/kernel bhyve will have to be recompiled after this.
Reviewed by: neel
Approved by: re@ (blanket)
amd64 and i386.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (blanket Xen)
MFC after: 2 weeks
sys/amd64/amd64/mp_machdep.c:
sys/amd64/include/cpu.h:
sys/i386/i386/mp_machdep.c:
sys/i386/include/cpu.h:
- Introduce two new CPU hooks for initialization and resume
purposes. This allows us to get rid of the XENHVM ifdefs in
mp_machdep, and also sets some hooks into common code that can be
used by other hypervisor implementations.
sys/amd64/conf/XENHVM:
sys/i386/conf/XENHVM:
- Remove these configs now that GENERIC has builtin support for Xen
HVM.
sys/kern/subr_smp.c:
- Make sure there are no pending IPIs when suspending a system.
sys/x86/xen/hvm.c:
- Add cpu init and resume vectors that are called from mp_machdep
using the new hooks.
- Only clear the vcpu_info mapping data on resume. It is already
clear for the BSP on a cold boot and is set correctly as APs
are started.
- Gate xen_hvm_init_cpu only to systems running under Xen.
sys/x86/xen/xen_intr.c:
- Gate the setup of event channels only to systems running under Xen.
- add fields to 'struct pmap' that are required to manage nested page tables.
- add a parameter to 'vmspace_alloc()' that can be used to override the
default pmap initialization routine 'pmap_pinit()'.
These changes are pushed ahead of the remaining changes in 'bhyve_npt_pmap'
in anticipation of the upcoming KBI freeze for 10.0.
Reviewed by: kib@, alc@
Approved by: re (glebius)
Xen PVHVM guest.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Reviewed by: gibbs
Approved by: re (blanket Xen)
MFC after: 2 weeks
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
- Make sure that are no MMU related IPIs pending on migration.
- Reset pending IPI_BITMAP on resume.
- Init vcpu_info on resume.
sys/amd64/include/intr_machdep.h:
sys/i386/include/intr_machdep.h:
sys/x86/acpica/acpi_wakeup.c:
sys/x86/x86/intr_machdep.c:
sys/x86/isa/atpic.c:
sys/x86/x86/io_apic.c:
sys/x86/x86/local_apic.c:
- Add a "suspend_cancelled" parameter to pic_resume(). For the
Xen PIC, restoration of interrupt services differs between
the aborted suspend and normal resume cases, so we must provide
this information.
sys/dev/acpica/acpi_timer.c:
sys/dev/xen/timer/timer.c:
sys/timetc.h:
- Don't swap out "suspend safe" timers across a suspend/resume
cycle. This includes the Xen PV and ACPI timers.
sys/dev/xen/control/control.c:
- Perform proper suspend/resume process for PVHVM:
- Suspend all APs before going into suspension, this allows us
to reset the vcpu_info on resume for each AP.
- Reset shared info page and callback on resume.
sys/dev/xen/timer/timer.c:
- Implement suspend/resume support for the PV timer. Since FreeBSD
doesn't perform a per-cpu resume of the timer, we need to call
smp_rendezvous in order to correctly resume the timer on each CPU.
sys/dev/xen/xenpci/xenpci.c:
- Don't reset the PCI interrupt on each suspend/resume.
sys/kern/subr_smp.c:
- When suspending a PVHVM domain make sure there are no MMU IPIs
in-flight, or we will get a lockup on resume due to the fact that
pending event channels are not carried over on migration.
- Implement a generic version of restart_cpus that can be used by
suspended and stopped cpus.
sys/x86/xen/hvm.c:
- Implement resume support for the hypercall page and shared info.
- Clear vcpu_info so it can be reset by APs when resuming from
suspension.
sys/dev/xen/xenpci/xenpci.c:
sys/x86/xen/hvm.c:
sys/x86/xen/xen_intr.c:
- Support UP kernel configurations.
sys/x86/xen/xen_intr.c:
- Properly rebind per-cpus VIRQs and IPIs on resume.
pmap_clear_reference() has had exactly one caller in the kernel for
several years, more precisely, since FreeBSD 8. Now, that call no
longer exists.
Approved by: re (kib)
Sponsored by: EMC / Isilon Storage Division
While here, correct all consumers to pass NULL instead of 0 as we pass
capability rights as pointers now, not uint64_t.
Reported by: Daniel Peyrolon
Tested by: Daniel Peyrolon
Approved by: re (marius)
to implement epoll subset of functionality. The kqueue user data are 32bit
on i386 which is not enough for epoll user data so this patch overrides
kqueue fileops to maintain enough space in struct file.
Initial patch developed by me in 2007 and then extended and finished
by Yuri Victorovich.
Approved by: re (delphij)
Sponsored by: Google Summer of Code
Submitted by: Yuri Victorovich <yuri at rawbw dot com>
Tested by: Yuri Victorovich <yuri at rawbw dot com>
immediate operand. The presence of an SIB byte in decoding the ModR/M field
would cause 'imm_bytes' to not be set to the correct value.
Fix this by initializing 'imm_bytes' independent of the ModR/M decoding.
Reported by: grehan@
Approved by: re@
not cover entire superpage, avoid copying. Doing partial copy would
require demotion, which is incompatible with the already held locks.
Reported by: cperciva
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (delphij)
the maximum number of VT-d domains (256 on a Sandybridge). We now allocate a
VT-d domain for a guest only if the administrator has explicitly configured
one or more PCI passthru device(s).
If there are no PCI passthru devices configured (the common case) then the
number of virtual machines is no longer limited by the maximum number of
VT-d domains.
Reviewed by: grehan@
Approved by: re@
This should be sufficient for 10.0 and will do
until forthcoming work to avoid limitations
in this area is complete.
Thanks to Bela Lubkin at tidalscale for the
headsup on the apic/cpu id/io apic ASL parameters
that are actually hex values and broke when
written as decimal when 11 vCPUs were configured.
Approved by: re@
amount of free memory was close to the point at which we would begin
reclaiming pages. Now, we continuously scan the active page queue,
regardless of the amount of free memory. Consequently, we are continuously
calling pmap_ts_referenced() on active pages.
Prior to this change, pmap_ts_referenced() would always demote superpage
mappings in order to obtain finer-grained reference information. This made
sense because we were coming under memory pressure and would soon have to
begin reclaiming pages. Now, however, with continuous scanning of the
active page queue, these demotions are taking a toll on performance. For
example, on one of my test machines, the running time for the HPCC Random
Access benchmark (also known as GUPS) has increased by 54%. To address this
problem, I have replaced the demotion with a heuristic for periodically
clearing the reference flag on superpage mappings.
Reviewed by: kib
Approved by: re (glebius)
Sponsored by: EMC / Isilon Storage Division
IPI implmementations.
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
Submitted by: gibbs (misc cleanup, table driven config)
Reviewed by: gibbs
MFC after: 2 weeks
sys/amd64/include/cpufunc.h:
sys/amd64/amd64/pmap.c:
Move invltlb_globpcid() into cpufunc.h so that it can be
used by the Xen HVM version of tlb shootdown IPI handlers.
sys/x86/xen/xen_intr.c:
sys/xen/xen_intr.h:
Rename xen_intr_bind_ipi() to xen_intr_alloc_and_bind_ipi(),
and remove the ipi vector parameter. This api allocates
an event channel port that can be used for ipi services,
but knows nothing of the actual ipi for which that port
will be used. Removing the unused argument and cleaning
up the comments surrounding its declaration helps clarify
its actual role.
sys/amd64/amd64/mp_machdep.c:
sys/amd64/include/cpu.h:
sys/i386/i386/mp_machdep.c:
sys/i386/include/cpu.h:
Implement a generic framework for amd64 and i386 that allows
the implementation of certain CPU management functions to
be selected at runtime. Currently this is only used for
the ipi send function, which we optimize for Xen when running
on a Xen hypervisor, but can easily be expanded to support
more operations.
sys/x86/xen/hvm.c:
Implement Xen PV IPI handlers and operations, replacing native
send IPI.
sys/amd64/include/pcpu.h:
sys/i386/include/pcpu.h:
sys/i386/include/smp.h:
Remove NR_VIRQS and NR_IPIS from FreeBSD headers. NR_VIRQS
is defined already for us in the xen interface files.
NR_IPIS is only needed in one file per Xen platform and is
easily inferred by the IPI vector table that is defined in
those files.
sys/i386/xen/mp_machdep.c:
Restructure to more closely match the HVM implementation by
performing table driven IPI setup.
pmap_is_modified() and pmap_is_referenced(), same as it was done for
pmap_ts_referenced().
Consolidate identical code for pmap_is_modified() and
pmap_is_referenced() into helper pmap_page_test_mappings().
Reviewed by: alc
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
sf_buf_alloc()/sf_buf_free() inlines, to save two calls to an absolutely
empty functions.
Reviewed by: alc, kib, scottl
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
