This allows compatibility translation to take place on the stack
(md_ioctl is too big) and is more suitable as a public interface within
the kernel than the kern_ioctl interface.
Except for the initialization of the md_req from the md_ioctl
(including detection of kernel md_file pointers) and the updating
of the md_ioctl prior to return, this is a mechanical replacment
of md_ioctl and mdio with md_req and mdr.
Reviewed by: markj, cem, kib (assorted versions)
Obtained from: CheriBSD
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14704
Move locks from outside ioctl to the individual implementations.
This is the first step of changing the implementations to act on a
kernel-internal request struct rather than on struct md_ioctl and to
removing the use of kern_ioctl in mountroot.
Reviewed by: cem, kib, markj (prior version)
Obtained from: CheriBSD
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14700
unconditionally incrementing i in the loop;
Reported by: cem
MFC with: r330880
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14685
It seems default timeout of 100ms is not enough for my 2694L card,
while it was perfectly fine for others, even for full-height 2694.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
The NVME standard has required in section 7.2.6, since at least 1.1,
that a clean shutdown is signalled by deleting the subission and the
completion queues before setting the shutdown bit in CC. The 1.0
standard, apparently, did not and many of the early Intel cards didn't
care. Some newer cards care, at least one whose beta firmware can
scramble the card on an unclean shutdown. Linux has done this for some
time. To make it possible to move forward with an evaluation of this
pre-release card with wonky firmware, delete the queues on the card
when we delete the qpair structures.
Sponsored by: Netflix
We'll need to delete namespaces soon, so go ahead and stop making
these devices eternal. It doesn't help much, and will be getting in
the way soon.
Sponsored by: Netflix
During shutdown mps waits for its SSU requests to complete however when
performing a reboot after handling a panic the scheduler is stopped so
getmicrotime which is used can be non-functional.
Switch to using the same method as shutdown_panic to ensure we actually
complete.
In addition reduce the timeout when RB_NOSYNC is set in howto as we expect
this to fail.
Reviewed by: slm
MFC after: 1 week
Sponsored by: Multiplay
Differential Revision: https://reviews.freebsd.org/D12776
Compare sbavail() with the cached sb_off of already-sent data instead of
always comparing with zero. This will correctly close the connection and
send the FIN if the socket buffer contains some previously-sent data but
no unsent data.
Reported by: Harsh Jain @ Chelsio
Sponsored by: Chelsio Communications
- Remove the one use of is_tls_offload() and the function. AIO special
handling only needs to be disabled when a TOE socket is actively doing
TLS offload on transmit. The TOE socket's mode (which affects receive
operation) doesn't matter, so remove the check for the socket's mode and
only check if a TOE socket has TLS transmit keys configured to determine
if an AIO write request should fall back to the normal socket handling
instead of the TOE fast path.
- Move can_tls_offload() into t4_tls.c. It is not used in critical paths,
so inlining isn't that important. Change return type to bool while here.
Sponsored by: Chelsio Communications
When multiple trims are in the queue, collapse them as much as
possible. At present, this usually results in only a few trims being
collapsed together, but more work on that will make it possible to do
hundreds (up to some configurable max).
Sponsored by: Netflix
The TOE engine in Chelsio T6 adapters supports offloading of TLS
encryption and TCP segmentation for offloaded connections. Sockets
using TLS are required to use a set of custom socket options to upload
RX and TX keys to the NIC and to enable RX processing. Currently
these socket options are implemented as TCP options in the vendor
specific range. A patched OpenSSL library will be made available in a
port / package for use with the TLS TOE support.
TOE sockets can either offload both transmit and reception of TLS
records or just transmit. TLS offload (both RX and TX) is enabled by
setting the dev.t6nex.<x>.tls sysctl to 1 and requires TOE to be
enabled on the relevant interface. Transmit offload can be used on
any "normal" or TLS TOE socket by using the custom socket option to
program a transmit key. This permits most TOE sockets to
transparently offload TLS when applications use a patched SSL library
(e.g. using LD_LIBRARY_PATH to request use of a patched OpenSSL
library). Receive offload can only be used with TOE sockets using the
TLS mode. The dev.t6nex.0.toe.tls_rx_ports sysctl can be set to a
list of TCP port numbers. Any connection with either a local or
remote port number in that list will be created as a TLS socket rather
than a plain TOE socket. Note that although this sysctl accepts an
arbitrary list of port numbers, the sysctl(8) tool is only able to set
sysctl nodes to a single value. A TLS socket will hang without
receiving data if used by an application that is not using a patched
SSL library. Thus, the tls_rx_ports node should be used with care.
For a server mostly concerned with offloading TLS transmit, this node
is not needed as plain TOE sockets will fall back to software crypto
when using an unpatched SSL library.
New per-interface statistics nodes are added giving counts of TLS
packets and payload bytes (payload bytes do not include TLS headers or
authentication tags/MACs) offloaded via the TOE engine, e.g.:
dev.cc.0.stats.rx_tls_octets: 149
dev.cc.0.stats.rx_tls_records: 13
dev.cc.0.stats.tx_tls_octets: 26501823
dev.cc.0.stats.tx_tls_records: 1620
TLS transmit work requests are constructed by a new variant of
t4_push_frames() called t4_push_tls_records() in tom/t4_tls.c.
TLS transmit work requests require a buffer containing IVs. If the
IVs are too large to fit into the work request, a separate buffer is
allocated when constructing a work request. This buffer is associated
with the transmit descriptor and freed when the descriptor is ACKed by
the adapter.
Received TLS frames use two new CPL messages. The first message is a
CPL_TLS_DATA containing the decryped payload of a single TLS record.
The handler places the mbuf containing the received payload on an
mbufq in the TOE pcb. The second message is a CPL_RX_TLS_CMP message
which includes a copy of the TLS header and indicates if there were
any errors. The handler for this message places the TLS header into
the socket buffer followed by the saved mbuf with the payload data.
Both of these handlers are contained in tom/t4_tls.c.
A few routines were exposed from t4_cpl_io.c for use by t4_tls.c
including send_rx_credits(), a new send_rx_modulate(), and
t4_close_conn().
TLS keys for both transmit and receive are stored in onboard memory
in the NIC in the "TLS keys" memory region.
In some cases a TLS socket can hang with pending data available in the
NIC that is not delivered to the host. As a workaround, TLS sockets
are more aggressive about sending CPL_RX_DATA_ACK messages anytime that
any data is read from a TLS socket. In addition, a fallback timer will
periodically send CPL_RX_DATA_ACK messages to the NIC for connections
that are still in the handshake phase. Once the connection has
finished the handshake and programmed RX keys via the socket option,
the timer is stopped.
A new function select_ulp_mode() is used to determine what sub-mode a
given TOE socket should use (plain TOE, DDP, or TLS). The existing
set_tcpddp_ulp_mode() function has been renamed to set_ulp_mode() and
handles initialization of TLS-specific state when necessary in
addition to DDP-specific state.
Since TLS sockets do not receive individual TCP segments but always
receive full TLS records, they can receive more data than is available
in the current window (e.g. if a 16k TLS record is received but the
socket buffer is itself 16k). To cope with this, just drop the window
to 0 when this happens, but track the overage and "eat" the overage as
it is read from the socket buffer not opening the window (or adding
rx_credits) for the overage bytes.
Reviewed by: np (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D14529
- Change t4_ddp_mod_load() to return void instead of always returning
success. This avoids having to pretend to have proper support for
unloading when only part of t4_tom_mod_load() has run.
- If t4_register_uld() fails, don't invoke t4_tom_mod_unload() directly.
The module handling code in the kernel invokes MOD_UNLOAD on a module
whose MOD_LOAD fails with an error already.
Reviewed by: np (part of a larger patch)
MFC after: 1 month
Sponsored by: Chelsio Communications
Always terminate the list with -1 and document the ioctl behavior.
This preserves existing behavior as seen from userspace with the
addition of the unconditional termination which will not be seen by
working consumers of MDIOCLIST.
Because this ioctl can only be performed by root (in default
configurations) and is not used in the base system this bug is not
deemed to warrant either a security advisory or an eratta notice.
Reviewed by: kib
Obtained from: CheriBSD
Discussed with: security-officer (gordon)
MFC after: 3 days
Security: kernel heap buffer overflow
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14685
For _IO() ioctls, addr is a pointer to uap->data which is a caddr_t.
When the caddr_t stores an int, dereferencing addr as an (int *) results
in truncation on little-endian 64-bit systems and corruption (owing to
extracting top bits) on big-endian 64-bit systems. In practice the
value of chan was probably always zero on systems of the latter type as
all such FreeBSD platforms use a register-based calling convention.
Reviewed by: mav
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14673
As noted in the comment, UEFI spec claims the capabilities pointer is
optional, but some implementations will choke and attempt to dereference it
without checking. This specific problem was found on a Lenovo Thinkpad X220
that would panic in efirtc_identify.
On x86 the IA-PC Boot Flags in the FADT can signal whether VGA is
available or not.
Sponsored by: Citrix systems R&D
Reviewed by: marcel
Differential revision: https://reviews.freebsd.org/D14397
The gcc 7 does check for switch statement fall through cases, and if legit,
such complaint can besilenced by /* FALLTHROUGH */ comment. Unfortunately
such comment is quite limited, but will still notify the reader.
This patch is backport from illumos, see
https://www.illumos.org/rb/r/941/
Reviewed by: eadler
Differential Revision: https://reviews.freebsd.org/D14663
For each regulators create an hw.regulator.<regname>. :
uvolt: Current value
always_on: 1 If the reg is always on
boot_on: 1 If the reg is set at boot time
enable_cnt: Number of consumer(s)
enable_delay: Delay before enabling the regulator
ramp_delay: The Ramp delay
max_uamp: The maximum value of the regulator in uAmps
min_uamp: The minimal value of the regulator in uAmps
max_uvolt: The maximum value of the regulator in uVolts
min_uvolt: The minimal value of the regulator in uVolts
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D14578
These parameters may be changed via ifconfig(8); by default,
mgt / mcast rates are lowest possible and ucast rate is not set
(matches previous configuration).
While here, store some variables locally for better readability.
this check on open, but "iscsictl -M", or an iSCSI redirect received by
iscsid(8) could end up with two sessions with the same target name and
portal.
MFC after: 2 weeks
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
There is a difference when parsing a completion entry between Ethernet
and IB ports. When link layer is Ethernet the bits describe the type of
L3 header in the packet. In the case when link layer is Ethernet and VLAN
header is present the value of SL is equal to the 3 UP bits in the VLAN
header. If VLAN header is not present then the SL is undefined and consumer
of the completion should check if IB_WC_WITH_VLAN is set.
While that, this patch also fills the vlan_id field in the completion if
present.
linux commit 12f8fedef2ec94c783f929126b20440a01512c14
MFC after: 1 week
Sponsored by: Mellanox Technologies
mlx5core.
Do not consider the inability to create a firmware dump fatal, but
inform about the situation and allow the driver to attach. The device
might not implement the needed VSC, or we might not know the layout of
the registers map. In either case, only firmware dump functionality is
limited, the network operations should be fine.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
When the mlx5en(4) driver was converted to using BUSDMA(9) the call to
m_defrag() was moved after the part of the TX routine that strips the
header from the mbuf chain. Before it called m_defrag it first trimmed
off the now-empty mbufs from the start of the chain. This has the side
effect of also removing the head of the chain that has M_PKTHDR set.
m_defrag() will not defrag a chain that does not have M_PKTHDR set,
thus it was effectively never defragging the mbuf chains.
As it turns out, trimming the mbufs in this fashion is unnecessary since
the call to bus_dmamap_load_mbuf_sg doesn't map empty mbufs anyway, so
remove it.
Differential Revision: https://reviews.freebsd.org/D12050
Submitted by: mjoras@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Set and report vport MTU rather than physical MTU,
The driver will set both vport and physical port mtu
and will rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Based on Linux upstream commit:
cd255efff9baadd654d6160e52d17ae7c568c9d3
Submitted by: Meny Yossefi <menyy@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Currently the ifnet interface is named mceX, where X is a monotonically
incremented value. If the device is reset due to a fatal error, then the
interface name will change. Using the device unit number will keep the
naming consistent across the reset logic.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add support for PFC and implement reading the per priority statistics
using the sysctl(8) interface. PFC is used together with VLAN priority
and can be enabled and disabled on a per priority basis.
Global pause frames and PFC are incompatible features and surrounding
logic has been added to warn the user about misconfiguration.
Update relevant mlx5core APIs for PFC configuration.
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch accumulates the following Linux commits:
mlx5_health.c
- 78ccb25861d76a8fc5c678d762180e6918834200
mlx5_core: Fix wrong name in struct
- 171bb2c560f45c0427ca3776a4c8f4e26e559400
mlx5_core: Update health syndromes
- 0144a95e2ad53a40c62148f44fb0c1f9d2a0d1e9
mlx5_core: Use accessor functions to read from device memory
- ac6ea6e81a80172612e0c9ef93720f371b198918
mlx5_core: Use private health thread for each device
- fd76ee4da55abb21babfc69310d321b9cb9a32e0
mlx5_core: Fix internal error detection conditions
- 2241007b3d783cbdbaa78c30bdb1994278b6f9b9
mlx5: Clear health sick bit when starting health poll
- 712bfef60912d91033cb25739f7444d5b8d8c59f
mlx5: Fix version printout in case of health issue
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
mlx5_cmd.c
- be87544de8df2b1eb34bcb5e32691287d96f9ec4
mlx5_core: Fix async commands return code
- a31208b1e11df334d443ec8cace7636150bb8ce2
mlx5_core: New init and exit flow for mlx5_core
- 020446e01eebc9dbe7eda038e570ab9c7ab13586
mlx5_core: Prepare cmd interface to system errors handling
- 89d44f0a6c732db23b219be708e2fe1e03ee4842
mlx5_core: Add pci error handlers to mlx5_core driver
- 0d834442cc247c7b3f3bd6019512ae03e96dd99a
mlx5: Fix teardown errors that happen in pci error handler
mlx5_main.c
- 5fc7197d3a256d9c5de3134870304b24892a4908
mlx5: Add pci shutdown callback
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
accomplishes a few things:
- Makes NULL an invalid address in the kernel, which is useful for catching
bugs.
- Lays groundwork for radix-tree translation on POWER9, which requires the
direct map be at high memory.
- Similarly lays groundwork for a direct map on 64-bit Book-E.
The new base address is chosen as the base of the fourth radix quadrant
(the minimum kernel address in this translation mode) and because all
supported CPUs ignore at least the first two bits of addresses in real
mode, allowing direct-map addresses to be used in real-mode handlers.
This is required by Linux and is part of the architecture standard
starting in POWER ISA 3, so can be relied upon.
Reviewed by: jhibbits, Breno Leitao
Differential Revision: D14499
Add support for mapping priority to traffic class via sysctl
Submitted by: Slava Shwartsman <slavash@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Factor out port speed definitions into new port.h header file,
similarly as done in Linux upstream.
- Correct two existing port speed definitions in mlx5en according to
Linux upstream.
MFC after: 1 week
Sponsored by: Mellanox Technologies
Adding an interface might be done outside the device_attach() routine
and will then cause a panic, due to the VNET not being set.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The current implementation does not handle timeout in case of command
with callback request, and this can lead to deadlock if the command
doesn't get firmware response. Add delayed callback timeout work
before posting the command to firmware. In case of real firmware
command completion we will cancel the delayed work. In case of
firmware command timeout the callback timeout handler will be called
and it will simulate firmware completion with timeout error.
linux commit 65ee67084589c1783a74b4a4a5db38d7264ec8b5
MFC after: 1 week
Sponsored by: Mellanox Technologies
Call command completion handler in case of timeout when working in
interrupts mode. Avoid flushing the commands workqueue after acquiring
the semaphores to prevent a potential deadlock.
linux commit commit 9cba4ebcf374c3772f6eb61f2d065294b2451b49
MFC after: 1 week
Sponsored by: Mellanox Technologies
band aid until a better solution to find the correct interrupt controller
can be found.
While here fix one place in the GICv3 ITS driver where the offset wasn't
correctly applied.
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
bus provide it with its needed memory resources.
This allows us to use PCIe on the ThunderX2 and, with a previous version
of the patch, on the SoftIron 3000 with ACPI.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D8767
This was tested by Ben on HP Chromebook 13 G1 with a
Skylake CPU and Sunrise Point-LP I2C controller and by me on
Minnowboard Turbot with Atom E3826 (formerly Bay Trail)
Submitted by: Ben Pye <ben@curlybracket.co.uk>
Reviewed by: gonzo
Obtained from: DragonflyBSD (a4549657 by Imre Vadász)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13654
Creating a UD address handle from user-space or from the kernel-space,
when the link layer is ethernet, requires resolving the remote L3
address into a L2 address. Doing this from the kernel is easy because
the required ARP(IPv4) and ND6(IPv6) address resolving APIs are readily
available. In userspace such an interface does not exist and kernel
help is required.
It should be noted that in an IP-based GID environment, the GID itself
does not contain all the information needed to resolve the destination
IP address. For example information like VLAN ID and SCOPE ID, is not
part of the GID and must be fetched from the GID attributes. Therefore
a source GID should always be referred to as a GID index. Instead of
going through various racy steps to obtain information about the
GID attributes from user-space, this is now all done by the kernel.
This patch optimises the L3 to L2 address resolving using the existing
create address handle uverbs interface, retrieving back the L2 address
as an additional user-space information structure.
This commit combines the following Linux upstream commits:
IB/core: Let create_ah return extended response to user
IB/core: Change ib_resolve_eth_dmac to use it in create AH
IB/mlx5: Make create/destroy_ah available to userspace
IB/mlx5: Use kernel driver to help userspace create ah
IB/mlx5: Report that device has udata response in create_ah
MFC after: 1 week
Sponsored by: Mellanox Technologies
of years since the century, so strip the century out when converting to or
from bcd_clocktime format (the conversion routines will infer century by
pivoting on 70).
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
imcsmb(4) provides smbus(4) support for the SMBus controller functionality
in the integrated Memory Controllers (iMCs) embedded in Intel Sandybridge-
Xeon, Ivybridge-Xeon, Haswell-Xeon, and Broadwell-Xeon CPUs. Each CPU
implements one or more iMCs, depending on the number of cores; each iMC
implements two SMBus controllers (iMC-SMBs).
*** IMPORTANT NOTE ***
Because motherboard firmware or the BMC might try to use the iMC-SMBs for
monitoring DIMM temperatures and/or managing an NVDIMM, the driver might
need to temporarily disable those functions, or take a hardware interlock,
before using the iMC-SMBs. Details on how to do this may vary from board to
board, and the procedure may be proprietary. It is strongly suggested that
anyone wishing to use this driver contact their motherboard vendor, and
modify the driver as described in the manual page and in the driver itself.
(For what it's worth, the driver as-is has been tested on various SuperMicro
motherboards.)
Reviewed by: avg, jhb
MFC after: 1 week
Relnotes: yes
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D14447
Discussed with: avg, ian, jhb
Tested by: allanjude (previous version), Panasas
In the weird case where the user-provided buffer was zero bytes, we could break
out of PCIOCGETCONF and return without initializing error. In this case,
initialize error to zero -- we successfully did nothing, as requested.
Reported by: Coverity
Sponsored by: Dell EMC Isilon
'status' array passed to get_mouse_status() is usually uninitialized by
callers.
Fully populating it with values in get_mouse_status() can fail due to
read_aux_data().
Additionally, nothing in API constrains 'len' to be >= 3. In practice,
every caller passes three, so perhaps that argument should just be removed.
Refactoring is a larger change, though.
Remove use of potentially uninitialized values by:
1. Only printing 3 debug statuses if the passed array was at least
'len' >= 3;
2. Populating 'status' array up to first three elements, if read_aux_data()
failed.
No functional change intended.
Reported by: Coverity
Sponsored by: Dell EMC Isilon
6.0 spec 6.4.3.5 bit 0 is ignored on QWord, DWord, and Word Address Space
Descriptors, but not Extended Address Space Descriptors.
Reviewed by: jhb
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D14516
It calls OF_* functions to check if it needs to implement workarounds.
This may not be the case on arm64 where we support both FDT and ACPI.
Fix this by checking if we are booting on FDT before calling these checks.
Reviewed by: ian
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D14515
Chain frames required to satisfy all 2K of declared I/Os of 128KB each take
more then a megabyte of a physical memory, all of which existing code tries
allocate as physically contiguous. This patch removes that physical
contiguousness requirement, leaving only virtual contiguousness. I was
thinking about other ways of allocation, but the less granular allocation
becomes, the bigger is the overhead and/or complexity, reaching about 100%
overhead if allocate each frame separately.
The patch also bumps the chain frames hard limit from 2K to 16K. It is more
than enough for the case of default REQ_FRAMES and MAXPHYS (the drivers will
allocate less than that automatically), while in case of increased MAXPHYS
it will control maximal memory usage.
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D14420
After the auth key is copied into the ipad[] array, any remaining bytes
are cleared to zero (in case the key is shorter than one block size).
The full block size was used as the length of the zero rather than the
size of the remaining ipad[]. In practice this overflow was harmless as
it could only clear bytes in the following opad[] array which is
initialized with a copy of ipad[] in the next statement.
Sponsored by: Chelsio Communications
The parameters describe how much of the adapter's memory is reserved for
storing TLS keys. The 'meminfo' sysctl now lists this region of adapter
memory as 'TLS keys' if present.
Sponsored by: Chelsio Communications
* If compiled with EXT_RESOURCES look up the "biu" and "ciu" clocks in
the DT
* Don't use custom property "bus-frequency" but the standard one
"clock-frequency"
* Use the DT property max-frequency and fall back to 200Mhz if it don't exists
* Add more mmc caps suported by the controller
* Always ack all interrupts
* Subclassed driver can supply an update_ios so they can handle update
the clocks accordingly
* Take care of the DDR bit in update_ios (no functional change since we
do not support voltage change for now)
* Make use of the FDT bus-width property
libfdt now provides methods to iterate through subnodes and properties in a
convenient fashion.
Replace our ofw_fdt_{peer,child} searches with calls to their corresponding
libfdt methods. Rework ofw_fdt_nextprop to use the
fdt_for_each_property_offset macro, making it even more obvious what it's
doing.
No functional change intended.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D14225
the Server Base System Architecture to be a subset of the pl011 r1p5. As
we don't use the removed features it is safe to just attach to the existing
driver as is.
Sponsored by: DARPA, AFRL
network device pointer might be NULL. Wait for any pending tasks to
complete before calling axge_stop().
MFC after: 1 week
Sponsored by: Mellanox Technologies
No implementation of fpu_kern_enter() can fail, and it was causing needless
error checking boilerplate and confusion. Change the return code to void to
match reality.
(This trivial change took nine days to land because of the commit hook on
sys/dev/random. Please consider removing the hook or otherwise lowering the
bar -- secteam never seems to have free time to review patches.)
Reported by: Lachlan McIlroy <Lachlan.McIlroy AT isilon.com>
Reviewed by: delphij
Approved by: secteam (delphij)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14380
Also correct a typo in the comment for these values, noted by jimharris.
Reviewed by: jimharris
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3715
2. Sysctls to enable/disable driver_state_dump and error_recovery.
3. Sysctl to control the delay between hw/fw reinitialization and
restarting the fastpath.
4. Stop periodic stats retrieval if interface has IFF_DRV_RUNNING flag off.
5. Print contents of PEG_HALT_STATUS1 and PEG_HALT_STATUS2 on heartbeat
failure.
6. Speed up slowpath shutdown during error recovery.
7. link_state update using atomic_store.
8. Added timestamp information on driver state and minidump captures.
9. Added support for Slowpath event logging
10.Added additional failure injection types to simulate failures.
A super-set of the functionality of jedec_ts(4). jedec_dimm(4) reports asset
information (Part Number, Serial Number) encoded in the "Serial Presence
Detect" (SPD) data on JEDEC DDR3 and DDR4 DIMMs. It also calculates and
reports the memory capacity of the DIMM, in megabytes. If the DIMM includes
a "Thermal Sensor On DIMM" (TSOD), the temperature is also reported.
Reviewed by: cem
MFC after: 1 week
Relnotes: yes
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D14392
Discussed with: avg, cem
Tested by: avg, cem (previous version, no semantic changes)
Add chvgpio(4) driver for Intel Z8xxx SoC family. This product
was formerly known as Cherry Trail but Linux and OpenBSD drivers
refer to it as Cherry View. This driver is derived from OpenBSD
one so the name is kept for alignment with another BSD system.
Submitted by: Tom Jones <tj@enoti.me>
Reviewed by: gonzo, wblock(man page)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13086
Remove bitfields from defined structures as they are not portable.
Instead use shift and mask macros in the driver and nvmecontrol application.
NVMe is now working on powerpc64 host.
Submitted by: Michal Stanek <mst@semihalf.com>
Obtained from: Semihalf
Reviewed by: imp, wma
Sponsored by: IBM, QCM Technologies
Differential revision: https://reviews.freebsd.org/D13916
Now that we're queueing BIO_DELETE requests in the CAM I/O scheduler,
it make sense to try to combine as many as possible into a single
request to send down to hardware. Hopefully, lots of larger requests
like this are better than lots of individual transactions.
Note for future: need to limit based on total size of the trim
request. Should also collapse adjacent ranges where possible to
increase the size of the max payload.
Sponsored by: Netflix
Trying to grab locks during cngrab() when entering the debugger is
deadlock prone as all other CPUs are already halted (and thus unable
to release locks) when cngrab() is invoked. One could instead use
try-locks. However, the case that the try-lock fails still has to
be handled. In addition, if the try-lock works it doesn't provide
any greater ordering guarantees than is already provided by entering
and exiting DDB. It is simpler to define a simpler path for the
case that the try-lock would fail and always use that when entering
DDB. Messing with timers, etc. when entering DDB is dubious even if
the try-lock succeeds.
This patch attempts to use the smallest possible set of operations to
grab the vt(4) console when entering DDB without using any locks.
Reviewed by: emaste
Tested by: Matthew Macy
MFC after: 1 week
This consolidates all of the DDP state in one place. Also, the code has
now been fixed to ensure that DDP state is only accessed for DDP
connections. This should not be a functional change but makes it cleaner
and easier to add state for other TOE socket modes in the future.
MFC after: 1 month
Sponsored by: Chelsio Communications
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
VirtIO V1 provides configuration in multiple VENDOR capabilities so this
allows all of the configuration to be discovered.
Reviewed by: jhb
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14325
zero, matching the IEEE 1275 standard. Since these internal error paths
have never, to my knowledge, been taken, behavior is unchanged.
Reported by: gonzo
MFC after: 2 weeks
and index. A private function to do exactly that already existed, so this
renames gpio_pin_get_by_ofw_impl() to gpio_pin_get_by_ofw_propidx() and
provides a declaration for it in a public header.
Previously there were functions to get a pin by property name (assuming
there would only be one pin defined for the name), or by index (asuming
the property has the standard name "gpios"). It turns out there are
devicetree bindings that describe properties with names other than "gpios"
which can describe multiple pins. Hence the need to retrieve the Nth item
from a named property.
rather than relying on a set of canned EARLY_DRIVER_MODULE() statements in
the ofw_iicbus source. This means hw drivers will no longer be required to
use one of a few predefined driver names. They will also now be able to
decide themselves if they want to use DRIVER_MODULE or EARLY_DRIVER_MODULE
and to set which pass to attach on for early modules.
Mainly, this adds extern declarations for the driver and devclass variables.
It also renames ofwiicbus_devclass to ofw_iicbus_devclass to be consistant
with the way we use ofw_ prefixes on this stuff.
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
artificial NOMATCH usb does in lieu of creating a device_t for devices
with no drivers. Also, correct bus to be 'uhub' since where USB
devices attach, even though 'usb' is more logical, we need the
physical bus here.
Submitted by: hps@
Panasas discovered that ioctl(SIOCGLAGGPORT) returns ENOTTY for mxge(4) when
the NIC is not a member of a lagg. This came as a surprise, because the
SIOCGLAGGPORT handler in if_lagg.c only returns ENOENT (if run against the
laggX interface, rather than a physical port) or EINVAL (if run against a
non-member physical port). This behavior was not seen with other drivers,
such as bge(4), igb(4), and cxl(4). When I compared their respective ioctl
handlers, I found that they all called ether_ioctl() for the default (i.e.
unhandled) case; by contrast, mxge(4) only calls ether_ioctl() for two
specific cases, and returns ENOTTY for the default case.
Remove the two cases which explicitly call ether_ioctl(), and let the
default case call it instead. This matches what the vast majority of the NIC
drivers do.
Reviewed by: kmacy
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D14381
BWN_DEBUG_HWCRYPTO debug flag.
The MAC will attempt decryption (and set BWN_RX_MAC_DEC) even if a key has
not been supplied to the hardware; this is expected behavior, and there's
no need to spam users' console with this debugging printf.
compilation under FreeBSD. The mthca driver was temporarily removed as
part of the Linux 4.9 RoCE/infinband upgrade.
Top commit in Linux source tree:
69973b830859bc6529a7a0468ba0d80ee5117826
Sponsored by: Mellanox Technologies