This way the state changes from sleep->awake before the registers are poked
and from awake->sleep after the registers are poked.
This way spurious warnings aren't printed by my (to be committed)
debugging code.
Tested:
* AR5416, STA
private per-chip HAL.
This allows the ah_osdep.[ch] code to check whether the power state is
valid for doing chip programming.
It should be a no-op for normal driver work but it does require a
clean kernel/module rebuild, as the size of HAL structures have changed.
Now, this doesn't track whether the hardware is ACTUALLY awake,
as NETWORK_SLEEP wakes the chip up for a short period when traffic
is received. This doesn't actually set the power mode to AWAKE, so
we have to be careful about how we touch things.
But it's enough to start down the path of implementing station mode
chipset power savings, as a large part of the silliness is making
sure the chip is awake during periodic calibration / ANI and
random places where transmit may be occuring. I'd rather not a repeat
of debugging power save on ath9k, where races with calibration
and transmit path stuff took a couple years to shake out.
Tested:
* AR5416, STA mode
The AR5212 series of MACs implement the same channel counters as the
later 11n chips - except, of course, the 11n specific counter (extension
channel busy.)
This allows users of these NICs to use 'athsurvey' to see how busy their
current channel is.
Tested:
* AR5212, AR2413 NICs, STA mode
Approved by: re@ (gleb)
The reference HAL pushes a config group parameter to the driver layer
to inform it which particular chip behaviour to implement.
This particular value tags it as an AR9285.
The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
* Call the bluetooth setup function during the reset path, so the bluetooth
settings are actually initialised.
* Call the AR9285 diversity functions during bluetooth setup; so the AR9285
diversity and antenna configuration registers are correctly programmed
* Misc debugging info.
Tested:
* AR9285+AR3011 bluetooth combo; this code itself doesn't enable bluetooth
coexistence but it's part of what I'm currently using.
Now that I understand what's going on - and the RX antenna array maps
to what the receive LNA configuration actually is - I feel comfortable
in enabling this.
If people do have issues with this, there's enough debugging now available
that we have a chance to diagnose it without writing it up as 'weird
crap.'
Tested:
* AR9285 STA w/ diversity combining enabled in EEPROM
TODO:
* (More) testing in hostap mode
and controlling this form of antenna diversity) - print out the AR9285
antenna diversity configuration at attach time.
This will help track down and diagose if/when people have connectivity
issues on cards (eg if they connect a single antenna to LNA1, yet the
card has RX configured to only occur on LNA2.)
Tested:
* AR9285 w/ antenna diversity enabled in EEPROM;
* AR9285 w/ antenna diversity disabled in EEPROM; mapping only to a
single antenna (LNA1.)
for the RX path.
This is different to the div comb HAL flag, that says it actually
can use this for RX diversity (the "slow" diversity path implemented
but disabled in the AR9285 HAL code.)
Tested:
* AR9285, STA operation
The main problem here is that fast and driver RX diversity isn't actually
configured; I need to figure out why that is. That said, this makes
the single-antenna connected AR9285 and AR2427 (AR9285 w/ no 11n) work
correctly.
PR: kern/179269
The QCA9565 is a 1x1 2.4GHz 11n chip with integrated on-chip bluetooth.
The AR9300 HAL already has support for this chip; it just wasn't
included in the probe/attach path.
Tested:
* This commit brought to you over a QCA9565 wifi connection from
FreeBSD.
* .. ie, basic STA, pings, no iperf or antenna diversity checking just yet.
* Add ah_ratesArray[] to the ar5416 HAL state - this stores the maximum
values permissable per rate.
* Since different chip EEPROM formats store this value in a different place,
store the HT40 power detector increment value in the ar5416 HAL state.
* Modify the target power setup code to store the maximum values in the
ar5416 HAL state rather than using a local variable.
* Add ar5416RateToRateTable() - to convert a hardware rate code to the
ratesArray enum / index.
* Add ar5416GetTxRatePower() - which goes through the gymnastics required
to correctly calculate the target TX power:
+ Add the power detector increment for ht40;
+ Take the power offset into account for AR9280 and later;
+ Offset the TX power correctly when doing open-loop TX power control;
+ Enforce the per-rate maximum value allowable.
Note - setting a TPC value of 0x0 in the TX descriptor on (at least)
the AR9160 resulted in the TX power being very high indeed. This didn't
happen on the AR9220. I'm guessing it's a chip bug that was fixed at
some point. So for now, just assume the AR5416/AR5418 and AR9130 are
also suspect and clamp the minimum value here at 1.
Tested:
* AR5416, AR9160, AR9220 hostap, verified using (2GHz) spectrum analyser
* Looked at target TX power in TX descriptor (using athalq) as well as TX
power on the spectrum analyser.
TODO:
* The TX descriptor code sets the target TX power to 0 for AR9285 chips.
I'm not yet sure why. Disable this for TPC and ensure that the TPC
TX power is set.
* AR9280, AR9285, AR9227, AR9287 testing!
* 5GHz testing!
Quirks:
* The per-packet TPC code is only exercised when the tpc sysctl is set
to 1. (dev.ath.X.tpc=1.) This needs to be done before you bring the
interface up.
* When TPC is enabled, setting the TX power doesn't end up with a call
through to the HAL to update the maximum TX power. So ensure that
you set the TPC sysctl before you bring the interface up and configure
a lower TX power or the hardware will be clamped by the lower TX
power (at least until the next channel change.)
Thanks to Qualcomm Atheros for all the hardware, and Sam Leffler for use
of his spectrum analyser to verify the TX channel power.
is configured for higher rates (lower than max) but higher TX power
is configured for the lower rates, above the configured cap, to improve
long distance behaviour.
* Add the rest of the missing GPIO output mux types;
* Add in a new debug category;
* And a new MCI btcoex configuration option in ath_hal.ah_config
Obtained from: Qualcomm Atheros
to stuck beacons.
* Set the cabq readytime (ie, how long to burst for) to 50% of the total
beacon interval time
* fix the cabq adjustment calculation based on how the beacon offset is
calculated (the SWBA/DBA time offset.)
This is all still a bit magic voodoo but it does seem to have further
quietened issues with missed/stuck beacons under my local testing.
In any case, it better matches what the reference HAL implements.
Obtained from: Qualcomm Atheros
The HAL already included the STBC fields; it just needed to be exposed
to the driver and net80211 stack.
This should allow single-stream STBC TX and RX to be negotiated; however
the driver and rate control code currently don't do anything with it.
* Remove ar5416UpdateChainmasks();
* Remove the TX chainmask override code from the ar5416 TX descriptor
setup routines;
* Write a driver method to calculate the current chainmask based on the
operating mode and update the driver state;
* Call the HAL chainmask method before calling ath_hal_reset();
* Use the currently configured chainmask in the TX descriptors rather than
the hardware TX chainmasks.
Tested:
* AR5416, STA/AP mode - legacy and 11n modes
Right now the only way to set the chainmask is to set the hardware
configured chainmask through capabilities. This is fine for forcing
the chainmask to be something other than what the hardware is capable
of (eg to reduce TX/RX to one connected antenna) but it does change what
the HAL hardware chainmask configuration is.
For operational mode changes, it (may?) make sense to separately control
the TX/RX chainmask.
Right now it's done as part of ar5416_reset.c - ar5416UpdateChainMasks()
calculates which TX/RX chainmasks to enable based on the operating mode.
(1 for legacy and whatever is supported for 11n operation.) But doing
this in the HAL is suboptimal - the driver needs to know the currently
configured chainmask in order to correctly enable things for each
TX descriptor. This is currently done by overriding the chainmask
config in the ar5416 TX routines but this has to disappear - the AR9300
HAL support requires the driver to dynamically set the TX chainmask based
on the TX power and TX rate in order to meet mini-PCIe slot power
requirements.
So:
* Introduce a new HAL method to set the operational chainmask variables;
* Introduce null methods for the previous generation chipsets;
* Add new driver state to record the current chainmask separate from
the hardware configured chainmask.
Part #2 of this will involve disabling ar5416UpdateChainMasks() and moving
it into the driver; as well as properly programming the TX chainmask
based on the currently configured HAL chainmask.
Tested:
* AR5416, STA mode - both legacy (11a/11bg) and 11n rates - verified
that AR_SELFGEN_MASK (the chainmask used for self-generated frames like
ACKs and RTSes) is correct, as well as the TX descriptor contents is
correct.
an incorrectly calculated RTS duration value when transmitting aggregates.
These earlier 802.11n NICs incorrectly used the ACK duration time when
calculating what to put in the RTS of an aggregate frame. Instead it
should have used the block-ack time. The result is that other stations
may not reserve enough time and start transmitting _over_ the top of
the in-progress blockack field. Tsk.
This workaround is to popuate the burst duration field with the delta
between the ACK duration the hardware is using and the required duration
for the block-ack. The result is that the RTS field should now contain
the correct duration for the subsequent block-ack.
This doesn't apply for AR9280 and later NICs.
Obtained from: Qualcomm Atheros
Specifically - never jack the TX FIFO threshold up to the absolute
maximum; always leave enough space for two DMA transactions to
appear.
This is a paranoia from the Linux ath9k driver. It can't hurt.
Obtained from: Linux ath9k
This has reduced the number of TX delimiter and data underruns when
doing large UDP transfers (>100mbit).
This stops any HAL_INT_TXURN interrupts from occuring, which is a good
sign!
Obtained from: Qualcomm Atheros
This includes the HAL routines to setup, enable/activate/disable spectral
scan and configure the relevant registers.
This still requires driver interaction to enable spectral scan reporting.
Specifically:
* call ah_spectralConfigure() to configure and enable spectral scan;
* .. there's currently no way to disable spectral scan... that will have
to follow.
* call ah_spectralStart() to force start a spectral report;
* call ah_spectralStop() to force stop an active spectral report.
The spectral scan results appear as PHY errors (type 0x5 on the AR9280,
same as radar) but with the spectral scan bit set (0x10 in the last byte
of the frame) identifying it as a spectral report rather than a radar
FFT report.
Caveats:
* It's likely quite difficult to run spectral _and_ radar at the same
time. Enabling spectral scan disables the radar thresholds but
leaves radar enabled. Thus, the driver (for now) needs to ensure
that only one or the other is enabled.
* .. it needs testing on HT40 mode.
Tested:
* AR9280 in STA mode, HT/20 only
TODO:
* Test on AR9285, AR9287;
* Test in both HT20 and HT40 modes;
* .. all the driver glue.
Obtained from: Qualcomm Atheros
* Finish adding the HAL capability to announce whether a NIC supports
spectral scan or not;
* Add spectral scan methods to the HAL structure;
* Add HAL_SPECTRAL_PARAM for configuration of the spectral scan logic.
The capability ID and HAL_SPECTRAL_PARAM struct are from Qualcomm
Atheros.
enforcing the TXOP and TBTT limits:
* Frames which will overlap with TBTT will not TX;
* Frames which will exceed TXOP will be filtered.
This is not enabled by default; it's intended to be enabled by the
TDMA code on 802.11n capable chipsets.
what the maximum legal values are.
The current beacon timer configuration from TDMA wraps things at
HAL_BEACON_PERIOD-1 TU. For the 11a chips this is fine, but for
the 11n chips it's not enough resolution. Since the 11a chips have a
limit on what's "valid", just enforce this so when I do write larger
values in, they get suitably wrapped before programming.
Tested:
* AR5413, TDMA slave
Todo:
* Run it for a (lot) longer on a clear channel, ensure that no strange
slippages occur.
* Re-validate this on STA configurations, just to be sure.
After chatting with the MAC team, the TSF writes (at least on the 11n
MACs, I don't know about pre-11n MACs) are done as 64 bit writes that
can take some time. So, doing a 32 bit TSF write is definitely not
supported. Leave a comment here which explains that.
Whilst here, add a comment which outlines that after a reset or TSF
write, the TSF write may take a while (up to 50uS) to update.
A write or reset shouldn't be done whilst the previous one is in
flight. Also (and this isn't currently done) a read shouldn't
occur until the SLEEP32_TSF_WRITE_STAT is clear. Right now we're
not doing that, mostly because we haven't been doing lots of TSF
resets/writes until recently.
encryption types.
The AR5210 only has four WEP key slots, in contrast to what the
later MACs have (ie, the keycache.) So there's no way to store a "clear"
key.
Even if the driver is taught to not allocate CLR key entries for
the AR5210, the hardware will actually attempt to decode the encrypted
frames with the (likely all 0!) WEP keys.
So for now, disable the hardware encryption entirely and just so it
all in software. That allows both WEP -and- WPA to actually work.
If someone wishes to try and make hardware WEP _but_ software WPA work,
they'll have to create a HAL capability to enable/disable hardware
encryption based on the current STA/Hostap mode. However, making
multi-vap work with one WEP and one WPA VAP will require hardware
encryption to be disabled anyway.
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
* introduce a new HAL API method to pull out the TX status descriptor
contents.
* Add num_delims to the 11n first aggr method. This isn't used by the
driver at the moment so it won't affect anything.
* Add some more ANI spur immunity levels.
* For AR5111 radios attached to an AR5212, limit the 5GHz channels
that are available. A later revision of the AR5111 supports the 4.9GHz
PSB channels but right now there's no check in place for the radio
revision.
If someone wants PSB support on AR5212+AR5111 radios then please let
me know and I'll add the relevant version check.
Obtained from: Qualcomm Atheros
the internet as "AR9380 and later which didn't get its PCI ID written
in at power-on", so it's hardly an unknown constant.
Obtained from: Qualcomm Atheros
AR5416 and AR9280, but leave it disabled by default.
TL;DR: don't enable this code at all unless you go through the process
of getting the NIC re-certified. This is purely to be used as a
reference and NOT a certified solution by any stretch of the imagination.
The background:
The AR5112 RF synth right up to the AR5133 RF synth (used on the AR5416,
derivative is used for the AR9130/AR9160) only implement down to 2.5MHz
channel spacing in 5GHz. Ie, the RF synth is programmed in steps of 2.5MHz
(or 5, 10, 20MHz.) So they can't represent the quarter rate channels
in the 4.9GHz PSB (which end in xxx2MHz and xxx7MHz). They support
fractional spacing in 2GHz (1MHz spacing) (or things wouldn't work,
right?)
So instead of doing this, the RF synth programming for the AR5112 and
later code will round to the nearest available frequency.
If all NICs were RF5112 or later, they'll inter-operate fine - they all
program the same. (And for reference, only the latest revision of the
RF5111 NICs do it, but the driver doesn't yet implement the programming.)
However:
* The AR5416 programming didn't at all implement the fractional synth
work around as above;
* The AR9280 programming actually programmed the accurate centre frequency
and thus wouldn't inter-operate with the legacy NICs.
So this patch:
* Implements the 4.9GHz PSB fractional synth workaround, exactly as the
RF5112 and later code does;
* Adds a very dirty workaround from me to calculate the same channel
centre "fudge" to the AR9280 code when operating on fractional frequencies
in 5GHz.
HOWEVER however:
It is disabled by default. Since the HAL didn't implement this feature,
it's highly unlikely that the AR5416 and AR928x has been tested in these
centre frequencies. There's a lot of regulatory compliance testing required
before a NIC can have this enabled - checking for centre frequency,
for drift, for synth spurs, for distortion and spectral mask compliance.
There's likely a lot of other things that need testing so please don't
treat this as an exhaustive, authoritative list. There's a perfectly good
process out there to get a NIC certified by your regulatory domain, please
go and engage someone to do that for you and pay the relevant fees.
If a company wishes to grab this work and certify existing 802.11n NICs
for work in these bands then please be my guest. The AR9280 works fine
on the correct fractional synth channels (49x2 and 49x7Mhz) so you don't
need to get certification for that. But the 500KHz offset hack may have
the above issues (spur, distortion, accuracy, etc) so you will need to
get the NIC recertified.
Please note that it's also CARD dependent. Just because the RF synth
will behave correctly doesn't at all mean that the card design will also
behave correctly. So no, I won't enable this by default if someone
verifies a specific AR5416/AR9280 NIC works. Please don't ask.
Tested:
I used the following NICs to do basic interoperability testing at
half and quarter rates. However, I only did very minimal spectrum
analyser testing (mostly "am I about to blow things up" testing;
not "certification ready" testing):
* AR5212 + AR5112 synth
* AR5413 + AR5413 synth
* AR5416 + AR5113 synth
* AR9280
This doesn't specifically fix the issue(s) i'm seeing in this 2GHz
environment (where setting/increasing spur immunity causes OFDM restart
errors to skyrocket through the roof; but leaving it at 0 would leave
the environment cleaner..)
Pointy-hat-to: me, for committing this broken code in the first place.
I'm not sure where in the deep, distant past I found the AR_PHY_MODE
registers for half/quarter rate mode, but unfortunately that doesn't
seem to work "right" for non-AR9280 chips.
Specifically:
* don't touch AR_PHY_MODE
* set the PLL bits when configuring half/quarter rate
I've verified this on the AR9280 (5ghz fast clock) and the AR5416.
The AR9280 works in both half/quarter rate; the AR5416 unfortunately
only currently works at half rate. It fails to calibrate on quarter rate.
No, this isn't HT/5 and HT/10 support. This is the 11a half/quarter
rate support primarily used by the 4.9GHz and GSM band regulatory
domains.
This is definitely a work in progress.
TODO:
* everything in the last commit;
* lots more interoperability testing with the AR5212 half/quarter rate
support for the relevant chips;
* Do some interop testing on half/quarter rate support between _all_
the 11n chips - AR5416, AR9160, AR9280 (and AR9285/AR9287 when 2GHz
half/quarter rate support is coded up.)
used when running the chips in half/quarter rate.
This sets up some default parameters which are then overridden by the
driver (which manually configures things like slot timing at interface
start time.)
Although this is a copy-and-modify from the AR5212 HAL, I did peek
at the reference HAL and the ath9k driver to see what they did.
Ath9k in particular doesn't hard-code this - instead, their version
of ar5416InitUserSettings() does all of the relevant math.
TODO:
* do the math, not hard code things!
* fix the mac clock calculation for the AR9287; since it runs the
MAC clock at a higher rate, requiring all the duration calculations
to change;
* Do a whole lot more validation for half/quarter rates.
Obtained from: Qualcomm Atheros, Linux ath9k
Some of the math is a little wrong thanks to clocks in 11a mode running
at 44MHz when in fast clock mode (rather than 40MHz, which the chips
before AR9280 ran 11a in). That'll have to be addressed in a future commit.
This fixes the incorrect slot (and likely ACK/RTS timeout) values
which I see when enabling half/quarter rate support on the AR9280.
The resulting math matches the expected calculated default values.
Fix the strong signal diversity capability setting - I had totally
messed up the indentation.
Set the default values to match what's in the .ini for now, rather than
what values I had previously gleaned from places. This seems to work
quite well for the early AR5212 NICs I have. Of course, later NICs
have different PHYs and the radar configuration is very card/board
dependent..
Tested:
* ath1: AR5212 mac 5.3 RF5111 phy 4.1
ath1: 2GHz radio: 0x0023; 5GHz radio: 0x0017
This detects 1, 5, 25, 50, 75, 100uS pulses reliably (with no interference.)
However, 10uS pulses don't detect reliably. That may be around the
transition between short and long pulses so some further tuning may
improve things.
up on (at least) the AR5413.
The 30 second summary - if a CRC error frame comes in during PHY error
processing, that CRC bit will be set for all subsequent frames until
a non-CRC error frame is processed.
So to allow for accurate PHY error processing (Radar, and ANI on the AR5212
HAL chips) just tag the frame as being both CRC and PHY - let the driver
decide what to do with it.
PR: kern/169362
some HAL definitions rather than local definitions.
The original source (ath9k) pulled this stuff from the QCA driver and
removed the HAL_* prefix. I'm just restoring the correct order of things.
Obtained from: Qualcomm Atheros
This is a re-implementation based on the reference carrier code
for the AR5413.
Tested:
* Pulse detection for AR5212 and AR5413, to ensure the
correct behaviour for both chips
PR: kern/170904
Obtained from: Qualcomm Atheros
The comparison assumes maxFirstepLevel is a count, rather than a maximum
value. The array is 3 entries in size however 'maxFirstepLevel' is 2.
This bug also exists in the AR5212 HAL.
