Allow egress traffic to be mirrored to VSIs in promiscuous mode, as latest
firmware supports that from API version 1.5.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The hardware doesn't layout the Geneve VNI (Virtual Network
Identifier) quite the same as the VxLAN VNI, so it needs to
adjust it before sending through the Admin Queue commands as the
workaround.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch trims the source code, with limiting pieces of code for
PF or VF driver only, code style fixes, and annotation
rewording.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch refactors the NVM update command processing, with adding
a new element of nvm_wait_opcode in struct i40e_hw to indicate
the opcode it waits on, and putting the wait event check into
a function. In addition, that element needs to be initialized
or updated properly.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch centralizes all NVM update status info into a single
structure, by moving nvm_release_on_done from struct
i40e_adminq_info to struct i40e_hw, for better management.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Host Memory Cache(HMC) admin queue APIs were removed from the latest
datasheet, and hence remove its implementation.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
SR-IOV mode is currently set when dealing with VF devices. PF devices must
be taken into account as well if they have active VFs.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
A hardware capability check is missing before enabling RX VLAN stripping
during queue setup.
Also, while dev_conf.rxmode.hw_vlan_strip is currently a single bit that
can be stored in priv->hw_vlan_strip directly, it should be interpreted as
a boolean value for safety.
Fixes: f3db948918 ("mlx5: support Rx VLAN stripping")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
There is no guarantee that the new MTU is effective after writing its value
to sysfs. Retrieve it to be sure.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Memory regions are always local with raw Ethernet queues, drop the remote
property as it adds extra processing on the hardware side.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
If configuration fails due to lack of resources, be more specific
about which resources are lacking - work queues, read queues or
completion queues. Return -EINVAL instead of -1 if more queeues
are requested than are available.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
If device configuration failed due to a lack of resources, such as
if more queues are requested than are available, the queue release
functions are called with NULL pointers which were being dereferenced.
Skip releasing queues if they are NULL pointers.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
Following the discussions from:
http://dpdk.org/ml/archives/dev/2015-July/021721.htmlhttp://dpdk.org/ml/archives/dev/2016-April/038143.html
The value of these flags is 0, making them useless. Today, no example
application checks them on Rx, and only few drivers sets them and
silently give wrong packets to the application, which should not happen.
This patch removes the unused flags from rte_mbuf and their use in the
drivers. The i40e and fm10k are kept as they are today and should be
fixed to drop bad packets. The enic driver is managed by its maintainer
in another patch.
Fixes: c22265f6 ("mbuf: add new packet flags for i40e")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch modifies bond_mode_alb_enable function.
When mempool allocation fails errno code is returned
instead of rte_panic. This allow to decide on application level
if it should quit or retry for mempool allocation.
Signed-off-by: Michal Jastrzebski <michalx.k.jastrzebski@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Ensure that the port field is set in mbufs received from the null PMD.
Signed-off-by: Sean Harte <sean.harte@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Since _BSD_SOURCE was deprecated in favor of _DEFAULT_SOURCE in Glibc 2.19
and entirely removed in 2.20, various BSD ioctl macros are not exposed
anymore when _XOPEN_SOURCE is defined, and linux/if.h now conflicts with
net/if.h.
Add _DEFAULT_SOURCE and keep _BSD_SOURCE for compatibility with older
versions.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Testpmd application will crash in fclose() upon quit after running
the below command.
"sudo gdb --args ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf0 -n 4
--vdev 'eth_pcap0,tx_iface=enp1s0f1,rx_pcap=/tmp/test.pcap' --
--port-topology=chained -i"
The reason is, pcap vdev creation with tx stream type as "iface"
as in above command doesn't need member "dumpers" of
"struct tx_pcaps", hence will not have memory allocated for it.
It contains a garbage values, as local object of struct tx_pcaps
is not initialized to 0 inside rte_pmd_pcap_dev_init().
So calling pcap_dump_close() on dumper as part of eth_dev_stop()
is causing segfault in fclose().
Fix is to initialize local object of struct tx_pcaps to 0.
Also initialize local object of struct rx_pcaps to 0.
So during eth_dev_stop(), pcap_dump_close() will not be called if dumper
is NULL.
Fixes: 4c173302c3 ("pcap: add new driver")
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Private/conflicting ol_flags where used to enable UDP/TCP Tx
offloads. Use the common flags in PKT_TX_L4_MASK to support them.
When updating flags, also do some minor code rearranging for
slightly better performane.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
The offload flags variable (ol_flags) in rte_mbuf structure is 64-bits,
so local copy of it must be 64-bits too. Moreover bit comparison between
16-bits variable and 64-bits value make no sense. This breaks Tx vlan
IP and L4 offloads.
Coverity issue: 13218
Fixes: fefed3d1e6 ("enic: new driver")
Suggested-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Signed-off-by: John Daley <johndale@cisco.com>
Acked-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Add an ASSERT macro for the enic driver which is enabled when the log
level is >= RTE_LOG_DEBUG. Assert that number of mbufs to return to
the pool in the Tx function is never greater than the max allowed.
Signed-off-by: John Daley <johndale@cisco.com>
Reduce host CPU overhead of Tx packet processing:
* Use local variables inside per-packet loop instead of fields in structs.
* Factor book keeping and conditionals out of the per-packet loop where
possible.
* Post buffers to the nic at a maximum of every 64 packets
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Mbufs were returned to the pool one at a time. Use rte_mempool_put_bulk
instead. There were multiple function calls for each buffer returned.
Refactor this code into just 2 functions.
Signed-off-by: John Daley <johndale@cisco.com>
The NIC can either DMA a separate completion message for each completed
send or periodically just DMA the index of the last completed send.
Switch to the latter method which improves cache locality and performance.
Signed-off-by: John Daley <johndale@cisco.com>
The list of mbufs held by the driver on Tx was allocated in chunks
(a hold-over from the enic kernel mode driver). The structure used
next pointers across chunks which led to cache misses.
Allocate the array used to hold mbufs in flight on Tx with
rte_zmalloc_socket(). Remove unnecessary fields from the structure
and use head and tail pointers instead of next pointers.
Signed-off-by: John Daley <johndale@cisco.com>
Functions existed which were never called. Removed them. Also
rename the 'pmd' from the name of the Tx function to improve clarity.
Signed-off-by: John Daley <johndale@cisco.com>
The Tx functions were in enic_ethdev.c and enic_main.c - files in which
they did not logically belong. To make things consistent with most
other drivers, we therefore extract them and place them with the equivalent
Rx functions into a file called enic_rxtx.c.
Signed-off-by: John Daley <johndale@cisco.com>
Truncated packets occur on enic if an mbuf is not big enough to
receive it or there aren't enough mbufs if rx scatter is in use.
They show up as error packets but unlike other error packets (like
packets bad FCS) there are no nic drop counts incremented for them.
Truncated packets are calculated by subtracting hardware errors from
software errors. Note: this causes transient inaccuracies in the
ipackets count. Also, the length of truncated packets are counted
in ibytes even though truncated packets are dropped which can make
ibytes be slightly higher than it should be.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
Following the discussions from:
http://dpdk.org/ml/archives/dev/2015-July/021721.htmlhttp://dpdk.org/ml/archives/dev/2016-April/038143.html
Remove the unused flag from enic driver. Also, the enic driver is
now modified to drop bad packets instead of using a non-existent
flag to try and identify them as bad.
Fixes: 947d860c82 ("enic: improve Rx performance")
Fixes: 5776c30293 ("enic: fix error packets handling")
Fixes: 50765c820e ("enic: remove packet error conditional")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: John Daley <johndale@cisco.com>
rx_no_bufs is a hardware counter of packets dropped on the
interface due to no host buffers and should be used to update
r_stats->imissed counter instead of rx_nombuf.
Include rx_drop in ierrors. rx_drop is incremented if packets
arrive when the receive queue is disabled.
Add a structure and functions for initializing and clearing
software counters. Add count of Rx mbuf allocation failures
(rx_nombuf) as the first counter.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
GCC_VERSION is empty in case of clang:
/bin/sh: line 0: test: -ge: unary operator expected
It is the same issue as http://dpdk.org/dev/patchwork/patch/5994/
Fixes: 366113dbfb ("e1000: suppress misleading indentation warning")
Signed-off-by: Hiroyuki Mikita <h.mikita89@gmail.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Suspicious implicit sign extension: pf->fdir.match_counter_index
with type unsigned short (16 bits, unsigned) is promoted in
"pf->fdir.match_counter_index << 20" to type int (32 bits, signed),
then sign-extended to type unsigned long (64 bits, unsigned).
If "pf->fdir.match_counter_index << 20" is greater than 0x7FFFFFFF,
the upper bits of the result will all be 1.
To fix the issue explicitly cast pf->fdir.match_counter_index to uint32_t.
Coverity issue: 13315
Fixes: 05999aab4c ("i40e: add or delete flow director")
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
This patch enables configuring MTU for i40e.
Since changing MTU needs to reconfigure queue, the port must be
stopped before configuring MTU.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
When setting up the flexible paylaod selection rules, the value
NONUSE_FLX_PIT_DEST_OFF (== 63) is meant to disable the rule.
However, since the MK_FLX_PIT macro always added on an additional
offset of I40E_FLX_OFFSET_IN_FIELD_VECTOR (== 50) to the value passed
the functionality to disable the rule was broken.
This patch fixes this by checking for the disable value and not adding
the offset in that case.
Fixes: d8b90c4eab ("i40e: take flow director flexible payload configuration")
Reported-by: Michael Habibi <mikehabibi@gmail.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Previously, there was a known issue "On Intel® 40G Ethernet
Controller stopping the port does not really down the port link."
There were two reasons why the port was always kept up.
1. Old firmware versions had issues when "Set PHY config command"
was used on 40G NICs.
2. The kernel i40e driver didn't call "Set PHY config command" when
ifconfig up/down was used, it assumes the link is always up. But
in DPDK, ports are forced down when an applications quits. So if
the port is then switched to being controlled by kernel the driver,
the port can not be brought up through "ifconfig <ethx> up".
This patch fixes this issue by adding in "Set PHY config command"
into our driver. This is now possible because with newer firmware
there is no longer a problem using this command.
With this fix, after DPDK quit, if the port is switched to being used
by the kernel driver, "ethtool -s <ethx> autoneg on" can be used to
turn on the auto negotiation, and then port can be brought up through
"ifconfig <ethx> up".
NOTE: requires kernel i40e driver version >= 1.4.X
Fixes: 2f1e228174 ("i40e: skip link control as firmware workaround")
Fixes: 16c979f9ad ("i40e: disable setting of PHY configuration")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Change the Tx routine to ring the doorbell once per burst
and not on every Tx packet. This driver-level optimization
is necessary to achieve line rates for larger frame
sizes (1k or more).
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
- Process Tx completions based on configured Tx free threshold and
determine how much TX BDs are required before invoking bnx2x_tx_encap()
- Change bnx2x_tx_encap() to void function as it can now never fail
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Under certain scenarios, management firmware (MFW) periodically polls
the driver for LAN statistics. This patch implements the osal hook to
fill in the stats.
Fixes: ec94dbc573 ("qede: add base driver")
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Program the PCIe completion timeout to 4 sec to give enough time
to allow completions to be received successfully in some older systems.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
To be consistent with the naming for ARM NEON implementation,
ixgbe_rxtx_vec.c is renamed to ixgbe_rxtx_vec_sse.c.
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
