The flow perf application uses the srtcm_rfc2697 as meter profile
while doing the meter testing.
This patch adds new configuration parameter '--packet-mode' to
generate the meter flows with packet cir instead of byte cir.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Change meter-cir option to meter-profile to cover user input for CIR,
CBS & EBS values.
The usage is as below:
--meter-profile=N1,N2,N3 default value is 1250000 156250 0.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Add option "policy-mtr" to indicate if meter creation will include policy
or not. Meter creation will keep unchanged without it.
With "policy-mtr", the policy is introduced. API create_meter_policy
is to create a policy. API create_meter_rule will use it to create
a meter. The value of it is used to specify meter policy actions.
Signed-off-by: Haifei Luo <haifeil@nvidia.com>
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Add support for Address Sanitizer (ASan) for PPC/POWER architecture.
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
The l3fwd example should use the reserved IPv4/v6 reserved address
ranges defined in RFC5735, RFC5180 and RFC863 discard protocol for
the port number in the exact match mode of L3 forwarding.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Increase the number of routes from 8 to 16 that are statically added for
lpm and em mode as most of the SoCs support more than 8 interfaces.
The number of routes added is equal to the number of ethernet devices
ports enabled through port mask.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Remove the szedata2 device driver as the platform is no longer
supported.
Signed-off-by: Martin Spinler <spinler@cesnet.cz>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The ConnectX NIC series hardware provides only 63-bit
wide timestamps. The imposed limitations description
added to documentation.
At the moment there are no affected applications known
or bug reports neither, this is just the declaration
of limitation.
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch defines ASAN_SHADOW_OFFSET for arm64 according to the ASan
documentation. This offset should cover all arm64 VMAs supported by
ASan.
Signed-off-by: Volodymyr Fialko <vfialko@marvell.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Ruifeng Wang <ruifeng.wang@arm.com>
The DPAA DMA driver is an implementation of the dmadev APIs,
that provide means to initiate a DMA transaction from CPU.
The initiated DMA is performed without CPU being involved
in the actual DMA transaction. This is achieved via using
the QDMA controller of DPAA SoC.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Increase default value for config parameter RTE_LIBRTE_IP_FRAG_MAX_FRAG
from 4 to 8. This parameter controls maximum number of fragments per
packet in ip reassembly table. Increasing this value from 4 to 8 will
allow users to cover common case with jumbo packet size of 9KB and
fragments with default frame size (1500B).
As RTE_LIBRTE_IP_FRAG_MAX_FRAG is used in definition of public
structure (struct rte_ip_frag_death_row), this is an ABI change.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
These actions map to MAE action DECR_IP_TTL. It affects
the outermost header in the current processing state of
the packet, which might have been decapsulated by prior
action DECAP. It also updates IPv4 checksum accordingly.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Andy Moreton <amoreton@xilinx.com>
In heterogeneous computing system, processing is not only in the CPU.
Some tasks can be delegated to devices working in parallel.
When mixing network activity with task processing there may be the need
to put in communication the CPU with the device in order to synchronize
operations.
An example could be a receive-and-process application
where CPU is responsible for receiving packets in multiple mbufs
and the GPU is responsible for processing the content of those packets.
The purpose of this list is to provide a buffer in CPU memory visible
from the GPU that can be treated as a circular buffer
to let the CPU provide fondamental info of received packets to the GPU.
A possible use-case is described below.
CPU:
- Trigger some task on the GPU
- in a loop:
- receive a number of packets
- provide packets info to the GPU
GPU:
- Do some pre-processing
- Wait to receive a new set of packet to be processed
Layout of a communication list would be:
-------
| 0 | => pkt_list
| status |
| #pkts |
-------
| 1 | => pkt_list
| status |
| #pkts |
-------
| 2 | => pkt_list
| status |
| #pkts |
-------
| .... | => pkt_list
-------
Signed-off-by: Elena Agostini <eagostini@nvidia.com>
In heterogeneous computing system, processing is not only in the CPU.
Some tasks can be delegated to devices working in parallel.
When mixing network activity with task processing there may be the need
to put in communication the CPU with the device in order to synchronize
operations.
The purpose of this flag is to allow the CPU and the GPU to
exchange ACKs. A possible use-case is described below.
CPU:
- Trigger some task on the GPU
- Prepare some data
- Signal to the GPU the data is ready updating the communication flag
GPU:
- Do some pre-processing
- Wait for more data from the CPU polling on the communication flag
- Consume the data prepared by the CPU
Signed-off-by: Elena Agostini <eagostini@nvidia.com>
Add a function for the application to ensure the coherency
of the writes executed by another device into the GPU memory.
Signed-off-by: Elena Agostini <eagostini@nvidia.com>
In heterogeneous computing system, processing is not only in the CPU.
Some tasks can be delegated to devices working in parallel.
Such workload distribution can be achieved by sharing some memory.
As a first step, the features are focused on memory management.
A function allows to allocate memory inside the device,
or in the main (CPU) memory while making it visible for the device.
This memory may be used to save packets or for synchronization data.
The next step should focus on GPU processing task control.
Signed-off-by: Elena Agostini <eagostini@nvidia.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The computing device may operate in some isolated contexts.
Memory and processing are isolated in a silo represented by
a child device.
The context is provided as an opaque by the caller of
rte_gpu_add_child().
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
In heterogeneous computing system, processing is not only in the CPU.
Some tasks can be delegated to devices working in parallel.
The new library gpudev is for dealing with GPGPU computing devices
from a DPDK application running on the CPU.
The infrastructure is prepared to welcome drivers in drivers/gpu/.
Signed-off-by: Elena Agostini <eagostini@nvidia.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Added support to create flows with priority attribute set
randomly between 0 and a user supplied maximum value. This
is useful to measure performance on NICs which may have to
rearrange flows to honor flow priority.
Removed the lower limit of 100000 flows per batch.
Signed-off-by: Satheesh Paul <psatheesh@marvell.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
This patch add dmadev instances create during the PCI probe, and
destroy them during the PCI remove. Internal structures and HW
definitions was also included.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Add the basic device probe and remove functions and initial
documentation for new hisilicon DMA drivers.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
The delay drop is the common feature managed on per device basis
and the kernel driver is responsible one for the initialization and
rearming.
By default, the timeout value is set to activate the delay drop when
the driver is loaded.
A private flag "dropless_rq" is used to control the rearming. Only
when it is on, the rearming will be handled once received a timeout
event. Or else, the delay drop will be deactivated after the first
timeout occurs and all the Rx queues won't have this feature.
The PMD is trying to query this flag and warn the application when
some queues are created with delay drop but the flag is off.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
For the Ethernet RQs, if there all receiving descriptors are
exhausted, the packets being received will be dropped. This behavior
prevents slow or malicious software entities at the host from
affecting the network. While for hairpin cases, even if there is no
software involved during the packet forwarding from Rx to Tx side,
some hiccup in the hardware or back pressure from Tx side may still
cause the descriptors to be exhausted. In certain scenarios it may be
preferred to configure the device to avoid such packet drops,
assuming the posting of descriptors will resume shortly.
To support this, a new devarg "delay_drop" is introduced. By default,
the delay drop is enabled for hairpin Rx queues and disabled for
standard Rx queues. This value is used as a bit mask:
- bit 0: enablement of standard Rx queue
- bit 1: enablement of hairpin Rx queue
And this attribute will be applied to all Rx queues of a device.
The "rq_delay_drop" capability in the HCA_CAP is checked before
creating any queue. If the hardware capabilities do not support
this delay drop, all the Rx queues will still be created without
this attribute, and the devarg setting will be ignored even if it
is specified explicitly. A warning log is used to notify the
application when this occurs.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Set the 'present' parameter to 0 by default. It is configured by hardware,
users can set it to 1 for manual configuration.
Fixes: f611dada1a ("net/txgbe: update link setup process of backplane NICs")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
This patch introduces shared RxQ. All shared Rx queues with same group
and queue ID share the same rxq_ctrl. Rxq_ctrl and rxq_data are shared,
all queues from different member port share same WQ and CQ, essentially
one Rx WQ, mbufs are filled into this singleton WQ.
Shared rxq_data is set into device Rx queues of all member ports as
RxQ object, used for receiving packets. Polling queue of any member
ports returns packets of any member, mbuf->port is used to identify
source port.
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Implement set/get_sram_policy which support both Rx/Tx
direction truflow type the specific SRAM bank.
Signed-off-by: Jay Ding <jay.ding@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Farah Smith <farah.smith@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The accumulation of flow counters is not determined by the application
device arguments anymore. Instead it is now dictated by the platform
capabilities whether to do software based accumulation or not.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This change allows adding IP header matches for GRE flows that
does not specify outer IP header in the flow match pattern.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Enabled wildcard match support for IPv4 ingress flows.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Added support for socket redirect feature capability so applications
can enable or disable this feature. This patch contains the template
changes.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update driver to read the multi root capability and ignore
PCI address check while creating ulp session when multi root
capability is enabled in the hardware. DPDK HSI version updated
from 1.10.2.44 to 1.10.2.68.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
* Added support for NAT action for destination IP and port
combination for Thor devices.
* Consolidated the encapsulation and NAT entries for scaling flows
with NAT actions.
Signed-off-by: Kishore Padmanabha <kishore.padmanabha@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Shahaji Bhosle <sbhosle@broadcom.com>
Reviewed-by: Mike Baucom <michael.baucom@broadcom.com>
Reviewed-by: Randy Schacher <stuart.schacher@broadcom.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for unicast and broadcast MAC filter configuration.
Signed-off-by: Vijay Kumar Srivastava <vsrivast@xilinx.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Add new vDPA PMD to support vDPA operations of Xilinx devices.
This patch implements probe and remove functions.
Signed-off-by: Vijay Kumar Srivastava <vsrivast@xilinx.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Set the RTE_EVENT_DEV_CAP_REQUIRES_MAINT flag, and perform DSW
background tasks on rte_event_maintain() calls.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Tested-by: Richard Eklycke <richard.eklycke@ericsson.com>
Tested-by: Liron Himi <lironh@marvell.com>
This patch adds new api ``rte_event_eth_rx_adapter_queue_stats_get`` to
retrieve queue stats. The queue stats are in the format
``struct rte_event_eth_rx_adapter_queue_stats``.
For resetting the queue stats,
``rte_event_eth_rx_adapter_queue_stats_reset`` api is added.
The adapter stats_get and stats_reset apis are also updated to
handle queue level event buffer use case.
Signed-off-by: Naga Harish K S V <s.v.naga.harish.k@intel.com>
Acked-by: Jay Jayatheerthan <jay.jayatheerthan@intel.com>
Added table to the crypto device drivers documentation
stating the support of each PMD on Linux, FreeBSD and Windows.
Signed-off-by: Tal Shnaiderman <talshn@nvidia.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
