along with functions, SYSCTLs and tunables that are not used with
ATA_CAM in #ifndef ATA_CAM, similar to the existing #ifdef'ed ATA_CAM
code for the other way around. This makes it easier to understand
which parts of ata(4) actually are used in the new world order and
to later on remove the !ATA_CAM bits. It also makes it obvious that
there is something fishy with the C-bus front-end as well as in the
ATP850 support, as these used ATA_LOCKING which is defunct in the
ATA_CAM case. When fixing the former, ATA_LOCKING probably needs to
be brought back in some form or other.
Reviewed by: mav
MFC after: 1 week
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.
PR: kern/165271
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
to known AHCI-capable chips (AMD/NVIDIA), configured for legacy emulation.
Enabled by default to get additional performance and functionality of AHCI
when it can't be enabled by BIOS. Can be disabled to honor BIOS settings if
needed for some reason.
MFC after: 1 month
by rman_get_virtual(9) to access device registers sparc64 currently cares
about.
Ideally ata(4) should just be converted to access these using bus_space(9)
read/write functions instead as there's really no reason to do it the
former way. However, this part of ata-siliconimage.c should go away in
favor of siis(4) sooner or later anyway and I don't have the hardware to
actually test the SX4 bits of ata-promise.c.
Also ideally the other architectures should also properly handle the
BUS_SPACE_MAP_LINEAR flag of bus_space_map(9) so this code wouldn't need
to be #ifdef'ed.
Mac with this chipset does not initialize AHCI mode unless it is started
from EFI loader. However, legacy ATA mode works.
Submitted by: jkim@ (original version)
Approved by: re (kib)
MFC after: 1 week
accessing SATA registers. Unserialized access under heavy load caused
wrong speed reporting and potentially could cause device loss.
- To free memory and other resources (including above), allocated
during chipinit() method call on attach, add new chipdeinit() method,
called during driver detach.
Submitted by: Andrew Boyer <aboyer@averesystems.com> (initial version)
Approved by: re (kib)
MFC after: 1 week
should respond with all zeroes to any access to slave registers. Test with
PATA devices confirmed such behavior. Unluckily, Intel SATA controllers in
legacy emulation mode behave differently, not making any difference between
ATA and ATAPI devices. It causes false positive slave device detection and,
as result, command timeouts.
To workaround this problem, mask result of legacy-emulated soft-reset with
the device presence information received from the SATA-specific registers.
This improves hard-reset and hot-plug on these ports.
- Device with ID 0x29218086 is a 2-port variant of ICH9 in legacy mode.
Skip probing for nonexistent slave devices there.
- SMBus Controller
- SATA Controller
- HD Audio Controller
- Watchdog Controller
Thanks to Seth Heasley (seth.heasley@intel.com) for providing us code.
MFC after 3 days
via AHCI-like memory resource at BAR(5). Use it if BIOS was so kind to
allocate memory for that BAR. This allows hot-plug support and connection
speed reporting.
MFC after: 2 weeks
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
K2 SATA controllers. The chip's status register must be read first, and
as a long, for other registers to be correctly updated after a command, and
this includes the command sequence in device detection as well as the
previously handled case after interrupts. While here, clean up some
previous hacks related to this controller.
Reported by: many
Reviewed by: mav
MFC after: 3 weeks
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
corruption bug where if an ATA command is issued before DMA is started,
data will become available to the controller before it knows what to do
with it. This results in either data corruption or a controller crash.
This patch remedies the problem by adopting the workaround employed
by Linux and Darwin: starting the DMA engine prior to sending the ATA
command.
Observer on: Xserve G5
Reviewed by: mav
MFC after: 1 week
fix. On Apple OpenPICs, the low/high bit of the interrupt sense is only
respected for interrupt 0. We currently erroneously program all OpenPIC
interrupts level high instead of level low by default, which only matters
for some G5 systems where the SATA controllers use IRQ 0.
This change is a quick fix that will be reverted once the effect of
changing the default interrupt sense on embedded systems is known.
MFC after: 3 days
