following primary purposes:
1. Remove the dependency of linsysfs and linprocfs modules from linux.ko,
which will be architecture specific on amd64.
2. Incorporate into linux_common.ko general code for platforms on which
we'll support two Linuxulator modules (for both instruction set - 32 & 64 bit).
3. Move malloc(9) declaration to linux_common.ko, to enable getting memory
usage statistics properly.
Currently linux_common.ko incorporates a code from linux_mib.c and linux_util.c
and linprocfs, linsysfs and linux kernel modules depend on linux_common.ko.
Temporarily remove dtrace garbage from linux_mib.c and linux_util.c
Differential Revision: https://reviews.freebsd.org/D1072
In collaboration with: Vassilis Laganakos.
Reviewed by: trasz
exposes functions from kernel with proper DWARF CFI information so that
it becomes easier to unwind through them.
Using vdso is a mandatory for a thread cancelation && cleanup
on a modern glibc.
Differential Revision: https://reviews.freebsd.org/D1060
remains. Xen is planning to phase out support for PV upstream since it
is harder to maintain and has more overhead. Modern x86 CPUs include
virtualization extensions that support HVM guests instead of PV guests.
In addition, the PV code was i386 only and not as well maintained recently
as the HVM code.
- Remove the i386-only NATIVE option that was used to disable certain
components for PV kernels. These components are now standard as they
are on amd64.
- Remove !XENHVM bits from PV drivers.
- Remove various shims required for XEN (e.g. PT_UPDATES_FLUSH, LOAD_CR3,
etc.)
- Remove duplicate copy of <xen/features.h>.
- Remove unused, i386-only xenstored.h.
Differential Revision: https://reviews.freebsd.org/D2362
Reviewed by: royger
Tested by: royger (i386/amd64 HVM domU and amd64 PVH dom0)
Relnotes: yes
sys/amd64/amd64/mp_machdep.c, to the new common x86 source
sys/x86/x86/mp_x86.c.
Proposed and reviewed by: jhb
Review: https://reviews.freebsd.org/D2347
Sponsored by: The FreeBSD Foundation
sys/i386/i386/machdep.c to new file sys/x86/x86/cpu_machdep.c. Most
of the code is related to the idle handling.
Discussed with: pluknet
Sponsored by: The FreeBSD Foundation
translation. In particular, despite IO-APICs only take 8bit apic id,
IR translation structures accept 32bit APIC Id, which allows x2APIC
mode to function properly. Extend msi_cpu of struct msi_intrsrc and
io_cpu of ioapic_intsrc to full int from one byte.
KPI of IR is isolated into the x86/iommu/iommu_intrmap.h, to avoid
bringing all dmar headers into interrupt code. The non-PCI(e) devices
which generate message interrupts on FSB require special handling. The
HPET FSB interrupts are remapped, while DMAR interrupts are not.
For each msi and ioapic interrupt source, the iommu cookie is added,
which is in fact index of the IRE (interrupt remap entry) in the IR
table. Cookie is made at the source allocation time, and then used at
the map time to fill both IRE and device registers. The MSI
address/data registers and IO-APIC redirection registers are
programmed with the special values which are recognized by IR and used
to restore the IRE index, to find proper delivery mode and target.
Map all MSI interrupts in the block when msi_map() is called.
Since an interrupt source setup and dismantle code are done in the
non-sleepable context, flushing interrupt entries cache in the IR
hardware, which is done async and ideally waits for the interrupt,
requires busy-wait for queue to drain. The dmar_qi_wait_for_seq() is
modified to take a boolean argument requesting busy-wait for the
written sequence number instead of waiting for interrupt.
Some interrupts are configured before IR is initialized, e.g. ACPI
SCI. Add intr_reprogram() function to reprogram all already
configured interrupts, and call it immediately before an IR unit is
enabled. There is still a small window after the IO-APIC redirection
entry is reprogrammed with cookie but before the unit is enabled, but
to fix this properly, IR must be started much earlier.
Add workarounds for 5500 and X58 northbridges, some revisions of which
have severe flaws in handling IR. Use the same identification methods
as employed by Linux.
Review: https://reviews.freebsd.org/D1892
Reviewed by: neel
Discussed with: jhb
Tested by: glebius, pho (previous versions)
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
KVM clock shares the same data structures between the guest and the host
as Xen so it makes sense to just have a single copy of this code.
Differential Revision: https://reviews.freebsd.org/D1429
Reviewed by: royger (eariler version)
MFC after: 1 month
for counter mode), and AES-GCM. Both of these modes have been added to
the aesni module.
Included is a set of tests to validate that the software and aesni
module calculate the correct values. These use the NIST KAT test
vectors. To run the test, you will need to install a soon to be
committed port, nist-kat that will install the vectors. Using a port
is necessary as the test vectors are around 25MB.
All the man pages were updated. I have added a new man page, crypto.7,
which includes a description of how to use each mode. All the new modes
and some other AES modes are present. It would be good for someone
else to go through and document the other modes.
A new ioctl was added to support AEAD modes which AES-GCM is one of them.
Without this ioctl, it is not possible to test AEAD modes from userland.
Add a timing safe bcmp for use to compare MACs. Previously we were using
bcmp which could leak timing info and result in the ability to forge
messages.
Add a minor optimization to the aesni module so that single segment
mbufs don't get copied and instead are updated in place. The aesni
module needs to be updated to support blocked IO so segmented mbufs
don't have to be copied.
We require that the IV be specified for all calls for both GCM and ICM.
This is to ensure proper use of these functions.
Obtained from: p4: //depot/projects/opencrypto
Relnotes: yes
Sponsored by: FreeBSD Foundation
Sponsored by: NetGate
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
875. This intersects with the agp_i810.c, which supports all Intels
from i810 to Core i5/7. Both agp_intel.c and agp_i810.c are compiled
into kernel when device agp is specified in config, and agp_i810
attach seems to be selected by chance due to linking order.
Strip support for 810 and later from agp_intel.c. Since 440-class
chipsets do not support any long-mode capable CPUs, remove agp_intel.c
from amd64 kernel file list. Note that agp_intel.c is not compiled
into agp.ko on amd64 already.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
This patch adds support for MSI interrupts when running on Xen. Apart
from adding the Xen related code needed in order to register MSI
interrupts this patch also makes the msi_init function a hook in
init_ops, so different MSI implementations can have different
initialization functions.
Sponsored by: Citrix Systems R&D
xen/interface/physdev.h:
- Add the MAP_PIRQ_TYPE_MULTI_MSI to map multi-vector MSI to the Xen
public interface.
x86/include/init.h:
- Add a hook for setting custom msi_init methods.
amd64/amd64/machdep.c:
i386/i386/machdep.c:
- Set the default msi_init hook to point to the native MSI
initialization method.
x86/xen/pv.c:
- Set the Xen MSI init hook when running as a Xen guest.
x86/x86/local_apic.c:
- Call the msi_init hook instead of directly calling msi_init.
xen/xen_intr.h:
x86/xen/xen_intr.c:
- Introduce support for registering/releasing MSI interrupts with
Xen.
- The MSI interrupts will use the same PIC as the IO APIC interrupts.
xen/xen_msi.h:
x86/xen/xen_msi.c:
- Introduce a Xen MSI implementation.
x86/xen/xen_nexus.c:
- Overwrite the default MSI hooks in the Xen Nexus to use the Xen MSI
implementation.
x86/xen/xen_pci.c:
- Introduce a Xen specific PCI bus that inherits from the ACPI PCI
bus and overwrites the native MSI methods.
- This is needed because when running under Xen the MSI messages used
to configure MSI interrupts on PCI devices are written by Xen
itself.
dev/acpica/acpi_pci.c:
- Lower the quality of the ACPI PCI bus so the newly introduced Xen
PCI bus can take over when needed.
conf/files.i386:
conf/files.amd64:
- Add the newly created files to the build process.
For now restrict it to amd64. Other architectures might be
re-added later once tested.
Remove the drivers from the global NOTES and files files and move
them to the amd64 specifics.
Remove the drivers from the i386 modules build and only leave the
amd64 version.
Rather than depending on "inet" depend on "pci" and make sure that
ixl(4) and ixlv(4) can be compiled independently [2]. This also
allows the drivers to build properly on IPv4-only or IPv6-only
kernels.
PR: 193824 [2]
Reviewed by: eric.joyner intel.com
MFC after: 3 days
References:
[1] http://lists.freebsd.org/pipermail/svn-src-all/2014-August/090470.html
for amd64/linux32. Fix the entirely bogus (untested) version from
r161310 for i386/linux using the same shared code in compat/linux.
It is unclear to me if we could support more clock mappings but
the current set allows me to successfully run commercial
32bit linux software under linuxolator on amd64.
Reviewed by: jhb
Differential Revision: D784
MFC after: 3 days
Sponsored by: DARPA, AFRL
many thanks for their continued support of FreeBSD.
While I'm there, also implement a new build knob, WITHOUT_HYPERV to
disable building and installing of the HyperV utilities when necessary.
The HyperV utilities are only built for i386 and amd64 targets.
This is a stable/10 candidate for inclusion with 10.1-RELEASE.
Submitted by: Wei Hu <weh microsoft com>
MFC after: 1 week
Introduce a Xen specific nexus that is going to be used by Xen PV/PVH
guests.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/xen_nexus.c:
- Introduce a Nexus to use on Xen PV(H) guests, this prevents PV(H)
guests from using the legacy Nexus.
conf/files.amd64:
conf/files.i386:
- Add the xen nexus to the build.
Create a dummy bus so top level Xen devices can attach to it (instead
of attaching directly to the nexus). This allows to have all the Xen
related devices grouped under a single bus.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/xenpv.c:
- Attach the xenpv bus when running as a Xen guest.
- Attach the ISA bus if needed, in order to attach syscons.
conf/files.amd6:
conf/files.i386:
- Include the xenpv.c file in the build of i386/amd64 kernels using
XENHVM.
dev/xen/console/console.c:
dev/xen/timer/timer.c:
xen/xenstore/xenstore.c:
- Attach to the xenpv bus instead of the Nexus.
dev/xen/xenpci/xenpci.c:
- Xen specific devices on PVHVM guests are no longer attached to the
xenpci device, they are instead attached to the xenpv bus, remove
the now unused methods.
Create the necessary hooks in order to provide a Xen PV APIC
implementation that can be used on PVH. Most of the lapic ops
shouldn't be called on Xen, since we trap those operations at a higher
layer.
Sponsored by: Citrix Systems R&D
Approved by: gibbs
x86/xen/hvm.c:
x86/xen/xen_apic.c:
- Move IPI related code to xen_apic.c
x86/xen/xen_apic.c:
- Introduce Xen PV APIC implementation, most of the functions of the
lapic interface should never be called when running as PV(H) guest,
so make sure FreeBSD panics when trying to use one of those.
- Define the Xen APIC implementation in xen_apic_ops.
xen/xen_pv.h:
- Extern declaration of the xen_apic struct.
x86/xen/pv.c:
- Use xen_apic_ops as apic_ops when running as PVH guest.
conf/files.amd64:
conf/files.i386:
- Include the xen_apic.c file in the build of i386/amd64 kernels
using XENHVM.
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
execution to a emumation program via parsing of ELF header information.
With this kernel module and userland tool, poudriere is able to build
ports packages via the QEMU userland tools (or another emulator program)
in a different architecture chroot, e.g. TARGET=mips TARGET_ARCH=mips
I'm not connecting this to GENERIC for obvious reasons, but this should
allow the kernel module to be built by default and enable the building
of the userland tool (which automatically loads the kernel module).
Submitted by: sson@
Reviewed by: jhb@
On PVH there's no ACPI, so the CPU enumeration must be implemented
using Xen hypercalls.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
x86/xen/pvcpu_enum.c:
- Enumerate avaiable vCPUs on PVH by using the VCPUOP_is_up
hypercall.
- Set vcpu_id for PVH guests.
conf/files.amd64:
- Include the PV CPU enumerator in the XENHVM build.
When running as a PVH guest, there's no emulated i8254, so we need to
use the Xen PV timer as the early source for DELAY. This change allows
for different implementations of the early DELAY function and
implements a Xen variant for it.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
dev/xen/timer/timer.c:
dev/xen/timer/timer.h:
- Implement Xen early delay functions using the PV timer and declare
them.
x86/include/init.h:
- Add hooks for early clock source initialization and early delay
functions.
i386/i386/machdep.c:
pc98/pc98/machdep.c:
amd64/amd64/machdep.c:
- Set early delay hooks to use the i8254 on bare metal.
- Use clock_init (that will in turn make use of init_ops) to
initialize the early clock source.
amd64/include/clock.h:
i386/include/clock.h:
- Declare i8254_delay and clock_init.
i386/xen/clock.c:
- Rename DELAY to i8254_delay.
x86/isa/clock.c:
- Introduce clock_init that will take care of initializing the early
clock by making use of the init_ops hooks.
- Move non ISA related delay functions to the newly introduced delay
file.
x86/x86/delay.c:
- Add moved delay related functions.
- Implement generic DELAY function that will use the init_ops hooks.
x86/xen/pv.c:
- Set PVH hooks for the early delay related functions in init_ops.
conf/files.amd64:
conf/files.i386:
conf/files.pc98:
- Add delay.c to the kernel build.
Add the PV/PVH entry point and the low level functions for PVH
early initialization.
Approved by: gibbs
Sponsored by: Citrix Systems R&D
amd64/amd64/genassym.c:
- Add __FreeBSD_version define to assym.s so it can be used for the
Xen notes.
amd64/amd64/locore.S:
- Make bootstack global so it can be used from Xen kernel entry
point.
amd64/amd64/xen-locore.S:
- Add Xen notes to the kernel.
- Add the Xen PV entry point, that is going to call hammer_time_xen.
amd64/include/asmacros.h:
- Add ELFNOTE macros.
i386/xen/xen_machdep.c:
- Define HYPERVISOR_start_info for the XEN i386 PV port, which is
going to be used in some shared code between PV and PVH.
x86/xen/hvm.c:
- Define HYPERVISOR_start_info for the PVH port.
x86/xen/pv.c:
- Introduce hammer_time_xen which is going to perform early setup for
Xen PVH:
- Setup shared Xen variables start_info, shared_info and
xen_store.
- Set guest type.
- Create initial page tables as FreeBSD expects to find them.
- Call into native init function (hammer_time).
xen/xen-os.h:
- Declare HYPERVISOR_start_info.
conf/files.amd64:
- Add amd64/amd64/locore.S and x86/xen/pv.c to the list of files.
Right now, the semaphore write is scheduled after each batch, which is
not optimal and must be tuned.
Discussed with: alc
Tested by: pho
MFC after: 1 month
1.3 of Intelб╝ Virtualization Technology for Directed I/O Architecture
Specification. The Extended Context and PASIDs from the rev. 2.2 are
not supported, but I am not aware of any released hardware which
implements them. Code does not use queued invalidation, see comments
for the reason, and does not provide interrupt remapping services.
Code implements the management of the guest address space per domain
and allows to establish and tear down arbitrary mappings, but not
partial unmapping. The superpages are created as needed, but not
promoted. Faults are recorded, fault records could be obtained
programmatically, and printed on the console.
Implement the busdma(9) using DMARs. This busdma backend avoids
bouncing and provides security against misbehaving hardware and driver
bad programming, preventing leaks and corruption of the memory by wild
DMA accesses.
By default, the implementation is compiled into amd64 GENERIC kernel
but disabled; to enable, set hw.dmar.enable=1 loader tunable. Code is
written to work on i386, but testing there was low priority, and
driver is not enabled in GENERIC. Even with the DMAR turned on,
individual devices could be directed to use the bounce busdma with the
hw.busdma.pci<domain>:<bus>:<device>:<function>.bounce=1 tunable. If
DMARs are capable of the pass-through translations, it is used,
otherwise, an identity-mapping page table is constructed.
The driver was tested on Xeon 5400/5500 chipset legacy machine,
Haswell desktop and E5 SandyBridge dual-socket boxes, with ahci(4),
ata(4), bce(4), ehci(4), mfi(4), uhci(4), xhci(4) devices. It also
works with em(4) and igb(4), but there some fixes are needed for
drivers, which are not committed yet. Intel GPUs do not work with
DMAR (yet).
Many thanks to John Baldwin, who explained me the newbus integration;
Peter Holm, who did all testing and helped me to discover and
understand several incredible bugs; and to Jim Harris for the access
to the EDS and BWG and for listening when I have to explain my
findings to somebody.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
busdma implementations to coexist. Copy busdma_machdep.c to
busdma_bounce.c, which is still a single implementation of the busdma
interface on x86 for now. The busdma_machdep.c only contains common
and dispatch code.
Tested by: pho (as part of the larger patch)
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
Looking pretty good; this mostly works now. New code includes:
* Read cached entropy at startup, both from files and from loader(8) preloaded entropy. Failures are soft, but announced. Untested.
* Use EVENTHANDLER to do above just before we go multiuser. Untested.
Contains:
* Refactor the hardware RNG CPU instruction sources to feed into
the software mixer. This is unfinished. The actual harvesting needs
to be sorted out. Modified by me (see below).
* Remove 'frac' parameter from random_harvest(). This was never
used and adds extra code for no good reason.
* Remove device write entropy harvesting. This provided a weak
attack vector, was not very good at bootstrapping the device. To
follow will be a replacement explicit reseed knob.
* Separate out all the RANDOM_PURE sources into separate harvest
entities. This adds some secuity in the case where more than one
is present.
* Review all the code and fix anything obviously messy or inconsistent.
Address som review concerns while I'm here, like rename the pseudo-rng
to 'dummy'.
Submitted by: Arthur Mesh <arthurmesh@gmail.com> (the first item)
to implement epoll subset of functionality. The kqueue user data are 32bit
on i386 which is not enough for epoll user data so this patch overrides
kqueue fileops to maintain enough space in struct file.
Initial patch developed by me in 2007 and then extended and finished
by Yuri Victorovich.
Approved by: re (delphij)
Sponsored by: Google Summer of Code
Submitted by: Yuri Victorovich <yuri at rawbw dot com>
Tested by: Yuri Victorovich <yuri at rawbw dot com>
performance... Use SSE2 instructions for calculating the XTS tweek
factor... Let the compiler do more work and handle register allocation
by using intrinsics, now only the key schedule is in assembly...
Replace .byte hard coded instructions w/ the proper instructions now
that both clang and gcc support them...
On my machine, pulling the code to userland I saw performance go from
~150MB/sec to 2GB/sec in XTS mode. GELI on GNOP saw a more modest
increase of about 3x due to other system overhead (geom and
opencrypto)...
These changes allow almost full disk io rate w/ geli...
Reviewed by: -current, -security
Thanks to: Mike Hamburg for the XTS tweek algorithm
Re-structure Xen HVM support so that:
- Xen is detected and hypercalls can be performed very
early in system startup.
- Xen interrupt services are implemented using FreeBSD's native
interrupt delivery infrastructure.
- the Xen interrupt service implementation is shared between PV
and HVM guests.
- Xen interrupt handlers can optionally use a filter handler
in order to avoid the overhead of dispatch to an interrupt
thread.
- interrupt load can be distributed among all available CPUs.
- the overhead of accessing the emulated local and I/O apics
on HVM is removed for event channel port events.
- a similar optimization can eventually, and fairly easily,
be used to optimize MSI.
Early Xen detection, HVM refactoring, PVHVM interrupt infrastructure,
and misc Xen cleanups:
Sponsored by: Spectra Logic Corporation
Unification of PV & HVM interrupt infrastructure, bug fixes,
and misc Xen cleanups:
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
sys/x86/x86/local_apic.c:
sys/amd64/include/apicvar.h:
sys/i386/include/apicvar.h:
sys/amd64/amd64/apic_vector.S:
sys/i386/i386/apic_vector.s:
sys/amd64/amd64/machdep.c:
sys/i386/i386/machdep.c:
sys/i386/xen/exception.s:
sys/x86/include/segments.h:
Reserve IDT vector 0x93 for the Xen event channel upcall
interrupt handler. On Hypervisors that support the direct
vector callback feature, we can request that this vector be
called directly by an injected HVM interrupt event, instead
of a simulated PCI interrupt on the Xen platform PCI device.
This avoids all of the overhead of dealing with the emulated
I/O APIC and local APIC. It also means that the Hypervisor
can inject these events on any CPU, allowing upcalls for
different ports to be handled in parallel.
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
Map Xen per-vcpu area during AP startup.
sys/amd64/include/intr_machdep.h:
sys/i386/include/intr_machdep.h:
Increase the FreeBSD IRQ vector table to include space
for event channel interrupt sources.
sys/amd64/include/pcpu.h:
sys/i386/include/pcpu.h:
Remove Xen HVM per-cpu variable data. These fields are now
allocated via the dynamic per-cpu scheme. See xen_intr.c
for details.
sys/amd64/include/xen/hypercall.h:
sys/dev/xen/blkback/blkback.c:
sys/i386/include/xen/xenvar.h:
sys/i386/xen/clock.c:
sys/i386/xen/xen_machdep.c:
sys/xen/gnttab.c:
Prefer FreeBSD primatives to Linux ones in Xen support code.
sys/amd64/include/xen/xen-os.h:
sys/i386/include/xen/xen-os.h:
sys/xen/xen-os.h:
sys/dev/xen/balloon/balloon.c:
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/console/xencons_ring.c:
sys/dev/xen/control/control.c:
sys/dev/xen/netback/netback.c:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/xenpci/xenpci.c:
sys/i386/i386/machdep.c:
sys/i386/include/pmap.h:
sys/i386/include/xen/xenfunc.h:
sys/i386/isa/npx.c:
sys/i386/xen/clock.c:
sys/i386/xen/mp_machdep.c:
sys/i386/xen/mptable.c:
sys/i386/xen/xen_clock_util.c:
sys/i386/xen/xen_machdep.c:
sys/i386/xen/xen_rtc.c:
sys/xen/evtchn/evtchn_dev.c:
sys/xen/features.c:
sys/xen/gnttab.c:
sys/xen/gnttab.h:
sys/xen/hvm.h:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_if.m:
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenstore/xenstore.c:
sys/xen/xenstore/xenstore_dev.c:
sys/xen/xenstore/xenstorevar.h:
Pull common Xen OS support functions/settings into xen/xen-os.h.
sys/amd64/include/xen/xen-os.h:
sys/i386/include/xen/xen-os.h:
sys/xen/xen-os.h:
Remove constants, macros, and functions unused in FreeBSD's Xen
support.
sys/xen/xen-os.h:
sys/i386/xen/xen_machdep.c:
sys/x86/xen/hvm.c:
Introduce new functions xen_domain(), xen_pv_domain(), and
xen_hvm_domain(). These are used in favor of #ifdefs so that
FreeBSD can dynamically detect and adapt to the presence of
a hypervisor. The goal is to have an HVM optimized GENERIC,
but more is necessary before this is possible.
sys/amd64/amd64/machdep.c:
sys/dev/xen/xenpci/xenpcivar.h:
sys/dev/xen/xenpci/xenpci.c:
sys/x86/xen/hvm.c:
sys/sys/kernel.h:
Refactor magic ioport, Hypercall table and Hypervisor shared
information page setup, and move it to a dedicated HVM support
module.
HVM mode initialization is now triggered during the
SI_SUB_HYPERVISOR phase of system startup. This currently
occurs just after the kernel VM is fully setup which is
just enough infrastructure to allow the hypercall table
and shared info page to be properly mapped.
sys/xen/hvm.h:
sys/x86/xen/hvm.c:
Add definitions and a method for configuring Hypervisor event
delievery via a direct vector callback.
sys/amd64/include/xen/xen-os.h:
sys/x86/xen/hvm.c:
sys/conf/files:
sys/conf/files.amd64:
sys/conf/files.i386:
Adjust kernel build to reflect the refactoring of early
Xen startup code and Xen interrupt services.
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
sys/dev/xen/control/control.c:
sys/dev/xen/evtchn/evtchn_dev.c:
sys/dev/xen/netback/netback.c:
sys/dev/xen/netfront/netfront.c:
sys/xen/xenstore/xenstore.c:
sys/xen/evtchn/evtchn_dev.c:
sys/dev/xen/console/console.c:
sys/dev/xen/console/xencons_ring.c
Adjust drivers to use new xen_intr_*() API.
sys/dev/xen/blkback/blkback.c:
Since blkback defers all event handling to a taskqueue,
convert this task queue to a "fast" taskqueue, and schedule
it via an interrupt filter. This avoids an unnecessary
ithread context switch.
sys/xen/xenstore/xenstore.c:
The xenstore driver is MPSAFE. Indicate as much when
registering its interrupt handler.
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbusvar.h:
Remove unused event channel APIs.
sys/xen/evtchn.h:
Remove all kernel Xen interrupt service API definitions
from this file. It is now only used for structure and
ioctl definitions related to the event channel userland
device driver.
Update the definitions in this file to match those from
NetBSD. Implementing this interface will be necessary for
Dom0 support.
sys/xen/evtchn/evtchnvar.h:
Add a header file for implemenation internal APIs related
to managing event channels event delivery. This is used
to allow, for example, the event channel userland device
driver to access low-level routines that typical kernel
consumers of event channel services should never access.
sys/xen/interface/event_channel.h:
sys/xen/xen_intr.h:
Standardize on the evtchn_port_t type for referring to
an event channel port id. In order to prevent low-level
event channel APIs from leaking to kernel consumers who
should not have access to this data, the type is defined
twice: Once in the Xen provided event_channel.h, and again
in xen/xen_intr.h. The double declaration is protected by
__XEN_EVTCHN_PORT_DEFINED__ to ensure it is never declared
twice within a given compilation unit.
sys/xen/xen_intr.h:
sys/xen/evtchn/evtchn.c:
sys/x86/xen/xen_intr.c:
sys/dev/xen/xenpci/evtchn.c:
sys/dev/xen/xenpci/xenpcivar.h:
New implementation of Xen interrupt services. This is
similar in many respects to the i386 PV implementation with
the exception that events for bound to event channel ports
(i.e. not IPI, virtual IRQ, or physical IRQ) are further
optimized to avoid mask/unmask operations that aren't
necessary for these edge triggered events.
Stubs exist for supporting physical IRQ binding, but will
need additional work before this implementation can be
fully shared between PV and HVM.
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
sys/i386/xen/mp_machdep.c
sys/x86/xen/hvm.c:
Add support for placing vcpu_info into an arbritary memory
page instead of using HYPERVISOR_shared_info->vcpu_info.
This allows the creation of domains with more than 32 vcpus.
sys/i386/i386/machdep.c:
sys/i386/xen/clock.c:
sys/i386/xen/xen_machdep.c:
sys/i386/xen/exception.s:
Add support for new event channle implementation.
- change the SI_SUB_RUN_SCHEDULER sysinits in hv_utilc and
hv_netvsc_drv_freebsd.c to SI_SUB_KTHREAD_IDLE, since the
former is no longer in FreeBSD.
The use of these SYSINITs can probably be removed.
As part of this commit, add an nvme_strvis() function which borrows
heavily from cam_strvis(). This will allow stripping of
leading/trailing whitespace and also handle unprintable characters
in model/serial numbers. This function goes into a new nvme_util.c
file which is used by both the driver and nvmecontrol.
Sponsored by: Intel
Reviewed by: carl
MFC after: 3 days
- Reconnect with some minor modifications, in particular now selsocket()
internals are adapted to use sbintime units after recent'ish calloutng
switch.
1. Common headers for fdt.h and ofw_machdep.h under x86/include
with indirections under i386/include and amd64/include.
2. New modinfo for loader provided FDT blob.
3. Common x86_init_fdt() called from hammer_time() on amd64 and
init386() on i386.
4. Split-off FDT specific low-level console functions from FDT
bus methods for the uart(4) driver. The low-level console
logic has been moved to uart_cpu_fdt.c and is used for arm,
mips & powerpc only. The FDT bus methods are shared across
all architectures.
5. Add dev/fdt/fdt_x86.c to hold the fdt_fixup_table[] and the
fdt_pic_table[] arrays. Both are empty right now.
FDT addresses are I/O ports on x86. Since the core FDT code does
not handle different address spaces, adding support for both I/O
ports and memory addresses requires some thought and discussion.
It may be better to use a compile-time option that controls this.
Obtained from: Juniper Networks, Inc.
QLogic 8300 Series Adapters
Submitted by: David C Somayajulu (davidcs@freebsd.org) QLogic Corporation
Approved by: George Neville-Neil (gnn@freebsd.org)
The NTB allows you to connect two systems with this device using a PCI-e
link. The driver is made of two modules:
- ntb_hw which is a basic hardware abstraction layer for the device.
- if_ntb which implements the ntb network device and the communication
protocol.
The driver is limited at the moment to CPU memcpy instead of using DMA, and
only Back-to-Back mode is supported. Also the network device isn't full
featured yet. These changes will be coming soon. The DMA change will also
bring in the ioat driver from the project branch it is on now.
This is an initial port of the GPL/BSD Linux driver contributed by Jon Mason
from Intel. Any bugs are my contributions.
Sponsored by: Intel
Reviewed by: jimharris, joel (man page only)
Approved by: jimharris (mentor)
will prevent the kernel from linking if the device driver are included
without the virtio module. Remove pci and scbus for the same reason.
Also explain the relationship and necessity of the virtio and virtio_pci
modules. Currently in FreeBSD, we only support VirtIO PCI, but it could
be replaced with a different interface (like MMIO) and the device
(network, block, etc) will still function.
Requested by: luigi
Approved by: grehan (mentor)
MFC after: 3 days
generating binary diffs.
- Constify a few strings used in the driver.
- Style changes to make the driver compile with default clang settings.
Approved by: HighPoint Technologies
MFC after: 3 days
GIANT from VFS. In addition, disconnect also netsmb, which is a base
requirement for SMBFS.
In the while SMBFS regular users can use FUSE interface and smbnetfs
port to work with their SMBFS partitions.
Also, there are ongoing efforts by vendor to support in-kernel smbfs,
so there are good chances that it will get relinked once properly locked.
This is not targeted for MFC.
generator, found on IvyBridge and supposedly later CPUs, accessible
with RDRAND instruction.
From the Intel whitepapers and articles about Bull Mountain, it seems
that we do not need to perform post-processing of RDRAND results, like
AES-encryption of the data with random IV and keys, which was done for
Padlock. Intel claims that sanitization is performed in hardware.
Make both Padlock and Bull Mountain random generators support code
covered by kernel config options, for the benefit of people who prefer
minimal kernels. Also add the tunables to disable hardware generator
even if detected.
Reviewed by: markm, secteam (simon)
Tested by: bapt, Michael Moll <kvedulv@kvedulv.de>
MFC after: 3 weeks
- Remove cpuset stopped_cpus which is no longer used.
- Add a short comment for cpuset suspended_cpus clearing.
- Fix the un-ordered x86/acpica/acpi_wakeup.c in conf/files.amd64 and i386.
Pointed-out by: attilio@
suspend/resume procedures are minimized among them.
common:
- Add global cpuset suspended_cpus to indicate APs are suspended/resumed.
- Remove acpi_waketag and acpi_wakemap from acpivar.h (no longer used).
- Add some variables in acpi_wakecode.S in order to minimize the difference
among amd64 and i386.
- Disable load_cr3() because now CR3 is restored in resumectx().
amd64:
- Add suspend/resume related members (such as MSR) in PCB.
- Modify savectx() for above new PCB members.
- Merge acpi_switch.S into cpu_switch.S as resumectx().
i386:
- Merge(and remove) suspendctx() into savectx() in order to match with
amd64 code.
Reviewed by: attilio@, acpi@
identical now that the bus spaces are unified under sys/x86.
Replace them with a single uart_cpu_x86.c.
o delete uart_cpu_i386.c
o move uart_cpu_amd64.c to uart_cpu_x86.c
o update files.amd64 and files.i386 accordingly.
The 'make depend' rules have to use custom -I paths for the special compat
includes for the opensolaris/zfs headers.
This option will pull in the couple of files that are shared with dtrace,
but they appear to correctly use the MODULE_VERSION/MODULE_DEPEND rules
so loader should do the right thing, as should kldload.
Reviewed by: pjd (glanced at)
amd64, if 'device isa' is present quiesce the 8259A's during boot and
resume from suspend.
While here, be more selective on amd64 about which kernel configurations
need elcr.c.
MFC after: 2 weeks
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
64bit and 32bit ABIs. As a side-effect, it enables AVX on capable
CPUs.
In particular:
- Query the CPU support for XSAVE, list of the supported extensions
and the required size of FPU save area. The hw.use_xsave tunable is
provided for disabling XSAVE, and hw.xsave_mask may be used to
select the enabled extensions.
- Remove the FPU save area from PCB and dynamically allocate the
(run-time sized) user save area on the top of the kernel stack,
right above the PCB. Reorganize the thread0 PCB initialization to
postpone it after BSP is queried for save area size.
- The dumppcb, stoppcbs and susppcbs now do not carry the FPU state as
well. FPU state is only useful for suspend, where it is saved in
dynamically allocated suspfpusave area.
- Use XSAVE and XRSTOR to save/restore FPU state, if supported and
enabled.
- Define new mcontext_t flag _MC_HASFPXSTATE, indicating that
mcontext_t has a valid pointer to out-of-struct extended FPU
state. Signal handlers are supplied with stack-allocated fpu
state. The sigreturn(2) and setcontext(2) syscall honour the flag,
allowing the signal handlers to inspect and manipilate extended
state in the interrupted context.
- The getcontext(2) never returns extended state, since there is no
place in the fixed-sized mcontext_t to place variable-sized save
area. And, since mcontext_t is embedded into ucontext_t, makes it
impossible to fix in a reasonable way. Instead of extending
getcontext(2) syscall, provide a sysarch(2) facility to query
extended FPU state.
- Add ptrace(2) support for getting and setting extended state; while
there, implement missed PT_I386_{GET,SET}XMMREGS for 32bit binaries.
- Change fpu_kern KPI to not expose struct fpu_kern_ctx layout to
consumers, making it opaque. Internally, struct fpu_kern_ctx now
contains a space for the extended state. Convert in-kernel consumers
of fpu_kern KPI both on i386 and amd64.
First version of the support for AVX was submitted by Tim Bird
<tim.bird am sony com> on behalf of Sony. This version was written
from scratch.
Tested by: pho (previous version), Yamagi Burmeister <lists yamagi org>
MFC after: 1 month
back after I fix the breakages on some of our more exotic platforms.
While here, add the driver to the amd64 NOTES, so it can be picked up in LINT
builds.
This branch is now considered frozen: future bhyve development will take
place in a branch off -CURRENT.
sys/dev/bvm/bvm_console.c
sys/dev/bvm/bvm_dbg.c
- simple console driver/gdb debug port used for bringup. supported
by user-space bhyve executable
sys/conf/options.amd64
sys/amd64/amd64/minidump_machdep.c
- allow NKPT to be set in the kernel config file
sys/amd64/conf/GENERIC
- mptable config options; bhyve user-space executable creates an mptable
with number of CPUs, and optional vendor extension
- add bvm console/debug
- set NKPT to 512 to allow loading of large RAM disks from the loader
- include kdb/gdb
sys/amd64/amd64/local_apic.c
sys/amd64/amd64/apic_vector.S
sys/amd64/include/specialreg.h
- if x2apic mode available, use MSRs to access the local APIC, otherwise
fall back to 'classic' MMIO mode
sys/amd64/amd64/mp_machdep.c
- support AP spinup on CPU models that don't have real-mode support by
overwriting the real-mode page with a message that supplies the bhyve
user-space executable with enough information to start the AP directly
in 64-bit mode.
sys/amd64/amd64/vm_machdep.c
- insert pause statements into cpu shutdown busy-wait loops
sys/dev/blackhole/blackhole.c
sys/modules/blackhole/Makefile
- boot-time loadable module that claims all PCI bus/slot/funcs specified
in an env var that are to be used for PCI passthrough
sys/amd64/amd64/intr_machdep.c
- allow round-robin assignment of device interrupts to CPUs to be disabled
from the loader
sys/amd64/include/bus.h
- convert string ins/outs instructions to loops of individual in/out since
bhyve doesn't support these yet
sys/kern/subr_bus.c
- if the device was no created with a fixed devclass, then remove it's
association with the devclass it was associated with during probe.
Otherwise, new drivers do not get a chance to probe/attach since the
device will stay married to the first driver that it probed successfully
but failed to attach.
Sponsored by: NetApp, Inc.
While in_pseudo() etc. is often used in offloading feature support,
in_cksum() is mostly used to fix some broken hardware.
Keeping both around for the moment allows us to compile NIC drivers
even in an IPv6 only environment without the need to mangle them
with #ifdef INETs in a way they are not prepared for. This will
leave some dead code paths that will not be exercised for IPv6.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 3 days
Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
provide PCI devices for various hardware such as memory controllers, etc.
These PCI buses are not enumerated via ACPI however. Add qpi(4) psuedo
bus and Host-PCI bridge drivers to enumerate these buses. Currently the
driver uses the CPU ID to determine the bridges' presence.
In collaboration with: Joseph Golio @ Isilon Systems
MFC after: 2 weeks
The aeskeys_{amd64,i386}.S content was mostly obtained from OpenBSD,
no objections to the license from core.
Hardware provided by: Sentex Communications
Tested by: fabient, pho (previous versions)
MFC after: 1 month
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
- Support for uncore counting events: one fixed PMC with the uncore
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
Provide groundwork for 32-bit binary compatibility on non-x86 platforms,
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
This MFC is required for MFCs of later changes to the freebsd32
compatibility from HEAD.
Requested by: kib
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
Reviewed by: kib, jhb
framebuffer driver, etc. work on FreeBSD/amd64.
A significant amount of improvements were done by jkim@ during the recent
months to make vesa(4) work better, over the initial code import. This
work is based on OpenBSD's x86emu implementation and contributed by
paradox <ddkprog yahoo com> and swell.k at gmail com.
Hopefully I have stolen all their work to 8-STABLE :)
All bugs in this commit are mine, as usual.
shared and generalized between our current amd64, i386 and pc98.
This is just an initial step that should lead to a more complete effort.
For the moment, a very simple porting of cpufreq modules, BIOS calls and
the whole MD specific ISA bus part is added to the sub-tree but ideally
a lot of code might be added and more shared support should grow.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, kib, jhb, imp
Discussed on: arch
MFC: 3 weeks
lindev(4) [1] is supposed to be a collection of linux-specific pseudo
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
I initially committed libteken to sys/dev/syscons/teken, but now that
I'm working on a console driver myself, I noticed this was not a good
decision. Move it to sys/teken to make it easier for other drivers to
use a terminal emulator.
Also list teken.c in sys/conf/files, instead of listing it in all the
files.arch files separately.
* Driver for ACPI HP extra functionations, which required
ACPI WMI driver.
Submitted by: Michael <freebsdusb at bindone.de>
Approved by: re
MFC after: 2 weeks
- For CPUs that only support MCE (the machine check exception) but not MCA
(i.e. Pentium), all this does is print out the value of the machine check
registers and then panic when a machine check exception occurs.
- For CPUs that support MCA (the machine check architecture), the support is
a bit more involved.
- First, there is limited support for decoding the CPU-independent MCA
error codes in the kernel, and the kernel uses this to output a short
description of any machine check events that occur.
- When a machine check exception occurs, all of the MCx banks on the
current CPU are scanned and any events are reported to the console
before panic'ing.
- To catch events for correctable errors, a periodic timer kicks off a
task which scans the MCx banks on all CPUs. The frequency of these
checks is controlled via the "hw.mca.interval" sysctl.
- Userland can request an immediate scan of the MCx banks by writing
a non-zero value to "hw.mca.force_scan".
- If any correctable events are encountered, the appropriate details
are stored in a 'struct mca_record' (defined in <machine/mca.h>).
The "hw.mca.count" is a count of such records and each record may
be queried via the "hw.mca.records" tree by specifying the record
index (0 .. count - 1) as the next name in the MIB similar to using
PIDs with the kern.proc.* sysctls. The idea is to export machine
check events to userland for more detailed processing.
- The periodic timer and hw.mca sysctls are only present if the CPU
supports MCA.
Discussed with: emaste (briefly)
MFC after: 1 month
the kernel on amd64. Fill and read segment registers for mcontext and
signals. Handle traps caused by restoration of the
invalidated selectors.
Implement user-mode creation and manipulation of the process-specific
LDT descriptors for amd64, see sysarch(2).
Implement support for TSS i/o port access permission bitmap for amd64.
Context-switch LDT and TSS. Do not save and restore segment registers on
the context switch, that is handled by kernel enter/leave trampolines
now. Remove segment restore code from the signal trampolines for
freebsd/amd64, freebsd/ia32 and linux/i386 for the same reason.
Implement amd64-specific compat shims for sysarch.
Linuxolator (temporary ?) switched to use gsbase for thread_area pointer.
TODO:
Currently, gdb is not adapted to show segment registers from struct reg.
Also, no machine-depended ptrace command is added to set segment
registers for debugged process.
In collaboration with: pho
Discussed with: peter
Reviewed by: jhb
Linuxolator tested by: dchagin
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
This code is heavily inspired by Takanori Watanabe's experimental SMP patch
for i386 and large portion was shamelessly cut and pasted from Peter Wemm's
AP boot code.
When copying big structures, LLVM generates calls to memmove(), because
it may not be able to figure out whether structures overlap. This caused
linker errors to occur. memmove() is now implemented using bcopy().
Ideally it would be the other way around, but that can be solved in the
future. On ARM we don't do add anything, because it already has
memmove().
Discussed on: arch@
Reviewed by: rdivacky
Some time ago I started working on a library called libteken, which is
terminal emulator. It does not buffer any screen contents, but only
keeps terminal state, such as cursor position, attributes, etc. It
should implement all escape sequences that are implemented by the
cons25 terminal emulator, but also a fair amount of sequences that are
present in VT100 and xterm.
A lot of random notes, which could be of interest to users/developers:
- Even though I'm leaving the terminal type set to `cons25', users can
do experiments with placing `xterm-color' in /etc/ttys. Because we
only implement a subset of features of xterm, this may cause
artifacts. We should consider extending libteken, because in my
opinion xterm is the way to go. Some missing features:
- Keypad application mode (DECKPAM)
- Character sets (SCS)
- libteken is filled with a fair amount of assertions, but unfortunately
we cannot go into the debugger anymore if we fail them. I've done
development of this library almost entirely in userspace. In
sys/dev/syscons/teken there are two applications that can be helpful
when debugging the code:
- teken_demo: a terminal emulator that can be started from a regular
xterm that emulates a terminal using libteken. This application can
be very useful to debug any rendering issues.
- teken_stress: a stress testing application that emulates random
terminal output. libteken has literally survived multiple terabytes
of random input.
- libteken also includes support for UTF-8, but unfortunately our input
layer and font renderer don't support this. If users want to
experiment with UTF-8 support, they can enable `TEKEN_UTF8' in
teken.h. If you recompile your kernel or the teken_demo application,
you can hold some nice experiments.
- I've left PC98 the way it is right now. The PC98 platform has a custom
syscons renderer, which supports some form of localised input. Maybe
we should port PC98 to libteken by the time syscons supports UTF-8?
- I've removed the `dumb' terminal emulator. It has been broken for
years. It hasn't survived the `struct proc' -> `struct thread'
conversion.
- To prevent confusion among people that want to hack on libteken:
unlike syscons, the state machines that parse the escape sequences are
machine generated. This means that if you want to add new escape
sequences, you have to add an entry to the `sequences' file. This will
cause new entries to be added to `teken_state.h'.
- Any rendering artifacts that didn't occur prior to this commit are by
accident. They should be reported to me, so I can fix them.
Discussed on: current@, hackers@
Discussed with: philip (at 25C3)
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
and Core Duo), models 0xF (Core2), model 0x17 (Core2Extreme) and
model 0x1C (Atom).
In these CPUs, the actual numbers, kinds and widths of PMCs present
need to queried at run time. Support for specific "architectural"
events also needs to be queried at run time.
Model 0xE CPUs support programmable PMCs, subsequent CPUs
additionally support "fixed-function" counters.
- Use event names that are close to vendor documentation, taking in
account that:
- events with identical semantics on two or more CPUs in this family
can have differing names in vendor documentation,
- identical vendor event names may map to differing events across
CPUs,
- each type of CPU supports a different subset of measurable
events.
Fixed-function and programmable counters both use the same vendor
names for events. The use of a class name prefix ("iaf-" or
"iap-" respectively) permits these to be distinguished.
- In libpmc, refactor pmc_name_of_event() into a public interface
and an internal helper function, for use by log handling code.
- Minor code tweaks: staticize a global, freshen a few comments.
Tested by: gnn
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
features of CPUs like reading/writing machine-specific registers,
retrieving cpuid data, and updating microcode.
- Add cpucontrol(8) utility, that provides userland access to
the features of cpuctl(4).
- Add subsequent manpages.
The cpuctl(4) device operates as follows. The pseudo-device node cpuctlX
is created for each cpu present in the systems. The pseudo-device minor
number corresponds to the cpu number in the system. The cpuctl(4) pseudo-
device allows a number of ioctl to be preformed, namely RDMSR/WRMSR/CPUID
and UPDATE. The first pair alows the caller to read/write machine-specific
registers from the correspondent CPU. cpuid data could be retrieved using
the CPUID call, and microcode updates are applied via UPDATE.
The permissions are inforced based on the pseudo-device file permissions.
RDMSR/CPUID will be allowed when the caller has read access to the device
node, while WRMSR/UPDATE will be granted only when the node is opened
for writing. There're also a number of priv(9) checks.
The cpucontrol(8) utility is intened to provide userland access to
the cpuctl(4) device features. The utility also allows one to apply
cpu microcode updates.
Currently only Intel and AMD cpus are supported and were tested.
Approved by: kib
Reviewed by: rpaulo, cokane, Peter Jeremy
MFC after: 1 month
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
This includes:
o mtree (for legal/intel_wpi)
o manpage for i386/amd64 archs
o module for i386/amd64 archs
o NOTES for i386/amd64 archs
Approved by: mlaier (comentor)
refactored it to be a generic device.
Instead of being part of the standard kernel, there is now a 'nvram' device
for i386/amd64. It is in DEFAULTS like io and mem, and can be turned off
with 'nodevice nvram'. This matches the previous behavior when it was
first committed.
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
making the relevant files standard. This avoids duplication and
makes it easier to override/disable unwanted schemes. Since ARM
doesn't have a DEFAULTS configuration file, leave the source
files for the BSD and MBR partitioning schemes in files.arm for
now.
Implement all futex atomic operations in assembler to not depend on the
fuword() that does not allow to distinguish between -1 and failure return.
Correctly return 0 from atomic operations on success.
In collaboration with: rdivacky
Tested by: Scot Hetzel <swhetzel gmail com>, Milos Vyletel <mvyletel mzm cz>
Sponsored by: Google SoC 2007
aches as a read-only file. In a number of cases this has led to
compiles failing- usually due to some strange NFS drift which thinks
that the opt_ah.h in the compile directory is out of date wrt the
source it is copied from. When the copy is executed again, it fails
because the target is read-only. Oops. Modify the compile hooks
avoid this.
Discussed with a while back with: Sam Leffler
- Add a new apic_alloc_vectors() method to the local APIC support code
to allocate N contiguous IDT vectors (aligned on a M >= N boundary).
This function is used to allocate IDT vectors for a group of MSI
messages.
- Add MSI and MSI-X PICs. The PIC code here provides methods to manage
edge-triggered MSI messages as x86 interrupt sources. In addition to
the PIC methods, msi.c also includes methods to allocate and release
MSI and MSI-X messages. For x86, we allow for up to 128 different
MSI IRQs starting at IRQ 256 (IRQs 0-15 are reserved for ISA IRQs,
16-254 for APIC PCI IRQs, and IRQ 255 is reserved).
- Add pcib_(alloc|release)_msi[x]() methods to the MD x86 PCI bridge
drivers to bubble the request up to the nexus driver.
- Add pcib_(alloc|release)_msi[x]() methods to the x86 nexus drivers that
ask the MSI PIC code to allocate resources and IDT vectors.
MFC after: 2 months
dynamic nature (if no native aio code is available, the linux part
returns ENOSYS because of missing requisites) should be solved differently
than it is.
All this will be done in P4.
Not included in this commit is a backout of the changes to the native aio
code (removing static in some places). Those changes (and some more) will
also be needed when the reworked linux aio stuff will reenter the tree.
Requested by: rwatson
Discussed with: rwatson
Implement the linux_io_* syscalls (AIO). They are only enabled if the native
AIO code is available (either compiled in to the kernel or as a module) at
the time the functions are used. If the AIO stuff is not available there
will be a ENOSYS.
From the submitter:
---snip---
DESIGN NOTES:
1. Linux permits a process to own multiple AIO queues (distinguished by
"context"), but FreeBSD creates only one single AIO queue per process.
My code maintains a request queue (STAILQ of queue(3)) per "context",
and throws all AIO requests of all contexts owned by a process into
the single FreeBSD per-process AIO queue.
When the process calls io_destroy(2), io_getevents(2), io_submit(2) and
io_cancel(2), my code can pick out requests owned by the specified context
from the single FreeBSD per-process AIO queue according to the per-context
request queues maintained by my code.
2. The request queue maintained by my code stores contrast information between
Linux IO control blocks (struct linux_iocb) and FreeBSD IO control blocks
(struct aiocb). FreeBSD IO control block actually exists in userland memory
space, required by FreeBSD native aio_XXXXXX(2).
3. It is quite troubling that the function io_getevents() of libaio-0.3.105
needs to use Linux-specific "struct aio_ring", which is a partial mirror
of context in user space. I would rather take the address of context in
kernel as the context ID, but the io_getevents() of libaio forces me to
take the address of the "ring" in user space as the context ID.
To my surprise, one comment line in the file "io_getevents.c" of
libaio-0.3.105 reads:
Ben will hate me for this
REFERENCE:
1. Linux kernel source code: http://www.kernel.org/pub/linux/kernel/v2.6/
(include/linux/aio_abi.h, fs/aio.c)
2. Linux manual pages: http://www.kernel.org/pub/linux/docs/manpages/
(io_setup(2), io_destroy(2), io_getevents(2), io_submit(2), io_cancel(2))
3. Linux Scalability Effort: http://lse.sourceforge.net/io/aio.html
The design notes: http://lse.sourceforge.net/io/aionotes.txt
4. The package libaio, both source and binary:
http://rpmfind.net/linux/rpm2html/search.php?query=libaio
Simple transparent interface to Linux AIO system calls.
5. Libaio-oracle: http://oss.oracle.com/projects/libaio-oracle/
POSIX AIO implementation based on Linux AIO system calls (depending on
libaio).
---snip---
Submitted by: Li, Xiao <intron@intron.ac>
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
- TLS - complete
- pid/tid mangling - complete
- thread area - complete
- futexes - complete with issues
- clone() extension - complete with some possible minor issues
- mq*/timer*/clock* stuff - complete but untested and the mq* stuff is
disabled when not build as part of the kernel with native FreeBSD mq*
support (module support for this will come later)
Tested with:
- linux-firefox - works, tested
- linux-opera - works, tested
- linux-realplay - doesnt work, issue with futexes
- linux-skype - doesnt work, issue with futexes
- linux-rt2-demo - works, tested
- linux-acroread - doesnt work, unknown reason (coredump) and sometimes
issue with futexes
- various unix utilities in linux-base-gentoo3 and linux-base-fc4:
everything tried worked
On amd64 not everything is supported like on i386, the catchup is planned for
later when the remaining bugs in the new functions are fixed.
To test this new stuff, you have to run
sysctl compat.linux.osrelease=2.6.16
to switch back use
sysctl compat.linux.osrelease=2.4.2
Don't switch while running a linux program, strange things may or may not
happen.
Sponsored by: Google SoC 2006
Submitted by: rdivacky
Some suggestions/help by: jhb, kib, manu@NetBSD.org, netchild
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
- Linux ioctl support, with the other Linux changes MegaCli
will run if you mount linprocfs & linsysfs then set
sysctl compat.linux.osrelease=2.6.12 or similar. This works
on i386. It should work on amd64 but not well tested yet.
StoreLib may or may not work. Remember to kldload mfi_linux.
- Add in AEN (Async Event Notification) support so we can
get messages from the firmware when something happens.
Not all messages are in defined in event detail. Use
event_log to try to figure out what happened.
- Try to implement something like SIGIO for StoreLib. Since
mrmonitor doesn't work right I can't fully test it. StoreLib
works best with the rh9 base. In theory mrmonitor isn't
needed due to native driver support of AEN :-)
Now we can configure and monitor the RAID better.
Submitted by: IronPort Systems.
the linux module, since it is not cross-platform
- move linprocfs from "files" and "options" to architecture specific files,
since it only makes sense to build this for those architectures, where we
also have a linuxolator
- disable the build of the linuxolator on our tier-2 architecture "Alpha":
* we don't have a linux_base port which supports Alpha and at the
same time is not outdated/obsoleted upstream/in a good condition/
currently working
* the upcomming new default linux base port is based upon Fedora
Core 3 (security support via http://www.fedoralegacy.org), which
isn't available for Alpha (like the current default linux base
port which is based upon Red Hat 8)
* nobody answered my request for testing it ~1 month ago on
current@ and alpha@ (it doesn't surprises me, see above)
* a SoC student wouldn't have to waste time on something which
nobody is willing to test
This does not remove the alpha specific MD files of the linuxolator yet.
Discussed on: arch (mostly silence)
Spiritual support by: scottl
end for isa(4).
o Add a seperate bus frontend for acpi(4) and allow ISA DMA for
it when ISA is configured in the kernel. This allows acpi(4)
attachments in non-ISA configurations, as is possible for ia64.
o Add a seperate bus frontend for pci(4) and detect known single
port parallel cards.
o Merge PC98 specific changes under pc98/cbus into the MI driver.
The changes are minor enough for conditional compilation and
in this form invites better abstraction.
o Have ppc(4) usabled on all platforms, now that ISA specifics
are untangled enough.
via the debug.minidump sysctl and tunable.
Traditional dumps store all physical memory. This was once a good thing
when machines had a maximum of 64M of ram and 1GB of kvm. These days,
machines often have many gigabytes of ram and a smaller amount of kvm.
libkvm+kgdb don't have a way to access physical ram that is not mapped
into kvm at the time of the crash dump, so the extra ram being dumped
is mostly wasted.
Minidumps invert the process. Instead of dumping physical memory in
in order to guarantee that all of kvm's backing is dumped, minidumps
instead dump only memory that is actively mapped into kvm.
amd64 has a direct map region that things like UMA use. Obviously we
cannot dump all of the direct map region because that is effectively
an old style all-physical-memory dump. Instead, introduce a bitmap
and two helper routines (dump_add_page(pa) and dump_drop_page(pa)) that
allow certain critical direct map pages to be included in the dump.
uma_machdep.c's allocator is the intended consumer.
Dumps are a custom format. At the very beginning of the file is a header,
then a copy of the message buffer, then the bitmap of pages present in
the dump, then the final level of the kvm page table trees (2MB mappings
are expanded into a 4K page mappings), then the sparse physical pages
according to the bitmap. libkvm can now conveniently access the kvm
page table entries.
Booting my test 8GB machine, forcing it into ddb and forcing a dump
leads to a 48MB minidump. While this is a best case, I expect minidumps
to be in the 100MB-500MB range. Obviously, never larger than physical
memory of course.
minidumps are on by default. It would want be necessary to turn them off
if it was necessary to debug corrupt kernel page table management as that
would mess up minidumps as well.
Both minidumps and regular dumps are supported on the same machine.
enabled by default in NETSMB and smbfs.ko.
With the most of modern SMB providers requiring encryption by
default, there is little sense left in keeping the crypto part
of NETSMB optional at the build time.
This will also return smbfs.ko to its former properties users
are rather accustomed to.
Discussed with: freebsd-stable, re (scottl)
Not objected by: bp, tjr (silence)
MFC after: 5 days
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add in the Linux IOCTL shim and create the megadev0 device so
Linux LSI MegaRaid tools can run on FreeBSD until Linux emulation.
Add glue to build the modules but don't tie it into the build
yet until I test it from the CVS repo. via the mirror on an
amd64 machine.
Tie this into the Linux32 emulation on amd64 so the tools can
run on amd64 kernel.
Cleaned up by: ps (amr_linux.c)
