The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.
This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.
Obtained by: Linux, Atheros
to fetch the current channel busy statistics, rather than duplicating
it here.
This forms the (very crude) basis for doing basic channel surveying.
Sponsored by: Hobnob, Inc.
enabled if required by STA operation.
This quietens a lot of OFDM errors seen in hostap mode, where
there are no beacon RSSI levels to tune the dynamic range of the
baseband.
This may reduce reception range at the fringes, but does increase
stability.
Sponsored by: Hobnob, Inc.
The 5ghz hostap mode (where DFS is being done) requires ANI to be disabled
or the radar detection parameters don't work as advertised (as they're based
on signal strength level, and tweaking ANI affects the signal strangth,
dynamic range and power increase the baseband is looking for in order to
detect it as a "signal".)
Obtained from: Linux, Atheros
Sponsored by: Hobnob, Inc.
* If we fall through from an ANI command (eg because it's out of range,
or it's disabled) then fall through to the next ANI command rather then
being stuck there.
* Fix some off-by-one comparisons, meaning the final level in some parameters
were never tweaked.
Obtained from: Atheros
Sponsored by: Hobnob, Inc.
This forces a full reset of the baseband/radio and seems needed to clear
some issues (with Merlin at least) when the baseband gets confused in a
very noisy environment.
Sponsored by: Hobnob, Inc.
RX clear, RX extension clear.
This is useful for estimating channel business.
The same routines should be written for AR5210->AR5212 where appopriate.
Obtained from: Atheros
some unmerged interrupt status debugging code from my branch.
* Add ah_intrstate[8] which will have the record of the last
call to ath_hal_getintr().
* Wrap the KTR code behind ATH_KTR_INTR_DEBUG.
* Add the HAL interrupt debugging behind AH_INTERRUPT_DEBUGGING.
This is only done for the AR5416 and later NICs but it will be
trivial to add to the earlier NICs if required.
Neither are enabled by default, although to minimise HAL binary
API differences, the ah_intrstate[] array is always compiled into
the ath_hal struct.
* preserve AR_TxIntrReq on every descriptor in an aggregate chain,
not just the first descriptor;
* always blank out the descriptor in ar5416ChainTxDesc() when forming
aggregates - the way I'm using this in the 11n branch is to first
chain aggregates together, then use the other HAL calls to fill in
the details.
* Add the TID field in the TX status descriptor;
* Add in the 11n first/middle/last functions for fiddling
with the descriptors. These are from the Linux and the
reference driver, but I'm not (currently) using them.
* Add further AR_ISR_S5 register definitions.
Obtained from: Linux ath9k, Atheros
interfere with traffic, as the NF load can take quite a while and poking the
AGC every 10uS is just a bit silly.
Instead, just leave the baseband NF calibration where it is and just read it
back next time a longcal interval happens.
The AR5008/AR9001 series NICs have a bug where BB register reads
will occasionally be corrupted. This could cause issues with things
such as ANI, which adjust operational parameters based on the
BB radio register reads. This was introduced in the AR5008 chip
and fixed with the first released AR9002 series NIC (AR9280v2.)
A followup commit will implement the acutal WAR when reading
BB registers. I'm still not sure how I'll implement it - whether
it should be done in the osdep layer, or whether it should just
live in the AR5416 HAL. Either way, they can use this capability
bit to determine whether to implement the WAR or not.
Thankyou to various sources inside Atheros who have helped me track
down what this particular issue is.
Obtained from: Atheros
Pre-11n devices and AR5416 use AR_PHY(263) for current RX RSSI.
AR9130 and later have a fourth calibration register (for doing
ADC calibration) and thus the register has moved to AR_PHY(271).
This isn't currently used by any of the active code; I'm committing
this for completeness and in case any third party code attempts to
use it for legacy reasons.
* The AR_ISR_RAC interrupt processing method has a subtle bug in all
the MAC revisions (including pre-11n NICs) until AR9300v2.
If you're unlucky, the clear phase clears an update to one of the
secondary registers, which includes TX status.
This shows up as a "watchdog timeout" if you're doing very low levels
of TX traffic. If you're doing a lot of non-11n TX traffic, you'll
end up receiving a TX interrupt from some later traffic anyway.
But when TX'ing 11n aggregation session traffic (which -HEAD isn't yet
doing), you may find that you're only able to TX one frame (due to
BAW restrictions) and this may end up hitting this race condition.
The only solution is to not use RAC and instead use AR_ISR and the
AR_ISR_Sx registers. The bit in AR_ISR which represents the secondary
registers are not cleared; only the AR_ISR_Sx bits are. This way
any updates which occur between the read and subsequent write will
stay asserted and (correctly) trigger a subsequent interrupt.
I've tested this on the AR5416, AR9160, AR9280. I will soon test
the AR9285 and AR9287.
* The AR_ISR TX and RX bits (and all others!) are set regardless of
whether the contents of the AR_IMR register. So if RX mitigation is
enabled, RXOK is going to be set in AR_ISR and it would normally set
HAL_INT_RX.
Fix the code to not set HAL_INT_RX when RXOK is set and RX mitigation
is compiled in. That way the RX path isn't prematurely called.
I would see:
* An interrupt would come in (eg a beacon, or TX completion) where
RXOK was set but RXINTM/RXMINT wasn't;
* ath_rx_proc() be called - completing RX frames;
* RXINTM/RXMINT would then fire;
* ath_rx_proc() would then be called again but find no frames in the
queue.
This fixes the RX mitigation behaviour to not overly call ath_rx_proc().
* Start to flesh out more correct timer interrupt handling - it isn't
kite/merlin specific. It's actually based on whether autosleep support
is enabled or not.
This is sourced from my 11n TX branch and has been tested for a few weeks.
Finally, the interrupt handling change should likely be implemented
for AR5210, AR5211 and AR5212.
There are some timing concerns which I've yet to fully map out.
In any case, there's an existing software driven mitigation method
for TX interrupts and when TX'ing 11n frames, the whole frame itself
generates an interrupt rather then the subframes.
Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.
* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed
This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.
rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
reference driver does clear the async interrupts after each service.
I'll tinker with this in a future commit.
Obtained from: Atheros
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
* Fix SLEEP1/SLEEP2 register definitions; the CAB/Beacon timeout
fields have changed in AR5416 and later
* The TIM_PERIOD and DTIM_PERIOD registers are now microsecond fields,
not TU.
Obtained from: Linux ath9k, Atheros reference
Approved by: re (kib, blanket)
or later. Previous hardware had some as TU, some as 1/8th
TU.
* Modify AR_NEXT_DBA and AR_NEXT_SWBA to use a new macro,
ONE_EIGHTH_TU_TO_USEC(), which converts the 1/8th TU
fields to USEC. This is just cosmetic and matches the
Atheros reference driver.
* Fix AR_NEXT_TBTT, which is USEC, not TU.
Submitted by: paradyse@gmail.com
Approved by: re (kib, blanket)
if 5ghz fast clock is enabled in the current operating mode.
It's slightly dirty, but it's part of the reference HAL and used by
the (currently closed-source) radar event code to map radar pulses
back to microsecond durations.
Obtained from: Atheros
Approved by: re (kib, blanket)
* I messed up the order of parameter true/false; oops!
* AR_PHY_RADAR_1 was being written at the wrong place, and was writing
potential garbage to the hardware.
Approved by: re (kib)
* Teach the AR5212/AR5416 ANI code to use the RX filter methods, rather
than calling the RX filter routines directly.
* Make HAL_ANI_PRESENT and HAL_ANI_MODE unconditionally available,
regardless of whether ah_ani_function is masking it.
* (Mostly) fully disable ANI if interference mitigation is disabled.
When disabled, the ANI code doesn't touch any ANI/PHY registers,
leaving them the default value. This is in line with what the
Atheros reference driver does.
* Correctly set the ANI parameters during ANI reset, rather than
when ANI is enabled. In this way, if ANI is disabled or enabled
whilst the NIC is not active (and there's no current channel),
bogus parameters or a NULL pointer deference doesn't occur.
There's still some lingering issues - notably, the MIB events/interrupts
aren't fully disabled, so MIB interrupts still occur. I'll worry about
that later.
Approved by: re (kib)
This in particular fixes radar PHY handling - on the AR5212
NIC, one enables the AR_PHY_ERR_RADAR bit in AR_PHY_ERR;
the AR5416 and later also needs a bit set in AR_RX_FILTER.
A follow-up commit is needed to convert the AR5416 ANI code
to use this particular method, as it's currently using the
AR5212 methods directly.
Obtained from: Atheros
Approved by: re (kib)
the ADC calibrations if the NIC is in 5ghz 11a or 5ghz HT/20 modes.
I've been told that the dual-ADC is only engaged in turbo/40mhz modes.
Since Sowl (AR9160) seems to return valid-looking calibration data
in 5ghz 20MHz modes, I'm only disabling it for Merlin for now.
It may turn out I can disable it for all chipsets and only enable
it for 40MHz modes.
Approved by: re (kib)
It looks like this was mixed up with the AR9285 calibration code.
This code is now more in line with what Linux ath9k and Atheros
reference drivers do.
Obtained from: Atheros
Approved by: re (kib)
tools.
* introduce pe_enabled, which (will) indicate whether the radar
detection stuff is enabled or not. Right now it's incorrectly
set, based on something previously written. I'll sort it out
later.
* Don't set HAL_PHYERR_PARAM_ENABLE in pe_relstep to say whether
radar detection is on.
* Return whether blockradar, fir128 and enmaxrssi is enabled.
* Change some of the phyerr params to be integers rather than
HAL_BOOL so they can be set to the NOPARAM value when the
setup function is called. This is in line with other radar
parameters.
* Add new configuration parameters for fir128, blockradar and
enmaxrssi, rather than defaulting to off, on and on respectively.
Approved by: re (kib)
polluting the AR5416 code with later chipset support.
Note: ar9280InitPLL() supports Merlin (AR9280) and later (AR9285, AR9287.)
Submitted by: ssgriffonuser@gmail.com
Approved by: re (kib)
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)
The global ath_hal_debug now affects all instances of the HAL.
This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.
rather than global variables.
This specifically allows for debugging to be enabled per-NIC, rather
than globally.
Since the ath driver doesn't know about AH_DEBUG, and to keep the ABI
consistent regardless of whether AH_DEBUG is enabled or not, enable the
debug parameter always but only conditionally compile in the debug
methods if needed.
The ALQ support is currently still global pending some brainstorming.
Submitted by: ssgriffonuser@gmail.com
Reviewed by: adrian, bschmidt
For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.
This information was extracted from the Madwifi DFS branch along with
some local additions.
Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)
For further information, please see:
http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection
This includes references to the relevant patents which describe what
is going on.
Obtained from: Madwifi
Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.
The particulars:
* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.
The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.
Obtained from: Linux, Atheros
It isn't linked into the build because it's missing the TX power
and PDADC programming code.
This code is mostly based on the ath9k codebase, compared against
the Atheros codebase as appropriate.
What's implemented:
* probe/attach
* EEPROM board value programming
* RX initial calibration
* radio channel programming
* general MAC / baseband setup
* async fifo setup
* open-loop tx power calibration
What's missing before it can be enabled by default:
* TX power / calibration setting code
* closed-loop tx power calibration routines
* TSF2 handling
* generic timer support from ath9k
Obtained from: Atheros, ath9k
of the ANI statistics and committing some tools which use these.
* Change HAL_ANI_* commands _back_ to be numerical, rather than a
bitmap;
* modify access to the ANI control bitmap to convert a command to
a bitmap;
* Fix the ANI noise immunity fiddling for CCK errors - it wasn't
checking whether noise immunity was disabled or not.
which did AR5212 specific initialisation. This would cause some slight
silliness when enabling/disabling ANI.
Just to be completely correct - and to ensure the phy error mask/RX filter
register isn't incorrectly played with - make the ANI control function a
method, have it set appropriately for AR5212/AR5416, and call that from the
ANI control interface.
This should hopefully make it clearer to developers what is going on
and when TPC is being hacked on, make it obvious why it isn't working for
series 1, 2, 3.
I won't flip on setting TX power for TX series 1, 2, 3 until I've done
some further testing with Kite to ensure it doesn't break anything.
(Before people ask - yes, TPC is only needed for 5ghz regdomains and
yes, Kite is a 2.4ghz only chip, but there are potential use cases
for 2ghz TPC. I just need to sit down and ensure it's supported and
functional.)
control the antenna control bits for the four TX series and the
TPC settings for TX series 1, 2, 3.
The specifics:
* The TPC setting for TX series 0 is handled in ctl0.
* TPC is currently disabled, so the per-packet TX power is
set via the global per-rate TX power register, not per packet.
* The antenna control bits don't matter for AR5416 and later
so they should stay 0 (which they currently do); they may
be set for Kite but as there's no TX diversity supported
at the moment (it requires the NIC to be built with an
external antenna switch, matching how antenna diversity
is done on legacy NICs), so again keep them 0.
This is in preparation for supporting per-rate TPC on the
AR5416 and later. The Kite (and soon to come Kiwi) code
sets ctl8-11 to 0x0, which doesn't have any effect at
the moment. When TPC is enabled it would result in the
second, third and fourth TX series attmpts to be done with
a TX power of 0. This commit doesn't change that; it'll
be followed up with some commits to properly set the TPC
registers appropriately.
Since the returned NF will be -ve, checking for <= 0 is not good
enough. For now, check whether it equals 0 or -1; a future commit
will tidy this mess up and have it return HAL_BOOL instead.
is totally disabled.
The Atheros HAL code does this for Sowl/Howl but not for Owl (AR5416) where
RIFS is disabled by default.
This seems to quieten the occasional baseband hang I've been seeing with
the AR9160 in STA mode under constant heavy traffic load.
Obtained from: Atheros
for the AR9280 based NICs if it's actually enabled.
Some of the OLC code was erroneously called during setup
and calibration. This may have caused some incorrect behaviour.
table which contains the per-rate target TX power.
This code is shared between the v14 eeprom board setup (AR5416, AR9160,
AR9280) and will also be used by the upcoming Kite (AR9287) support.
environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
* Add Howl (ar9130) to the list of chips that have DFS/BB/MAC hangs
* Don't treat unknown BB hangs as fatal; ath9k/Atheros HAL don't
treat it as such.
* Add HAL_DEBUG_DFS to the debug fields in ath_hal/ah_debug.h
The BB hang check simply loops over an observation register checking
for a stuck state engine, but it can happen under high traffic
conditions. Ath9k and the Atheros HAL simply log a debug message and
continue.
Private to FreeBSD:
* Add HAL_DEBUG_HANG to the debug fields
* Change the hang debugging to HAL_DEBUG_HANG rather than HAL_DEBUG_DFS
like in the Atheros HAL.
Obtained from: Atheros
For now, these are equivalent macros. AR_SREV_OWL{X}_OR_LATER
will later change to exclude Howl (AR9130) in line with what
the Atheros HAL does.
This should not functionally change anything.
Obtained from: Atheros
A quick story, which is partially documented in the commit.
The silicon revision in Linux ath9k and the Atheros HAL use an
AR_SREV_REVISION mask of 0x07.
FreeBSD's HAL uses the AR5212 AR_SREV_REVISION mask of 0x0F.
Thus the OWL silicon revisions were coming through as 0xA, 0xB,
0xC, rather than 0x0, 0x1 and 0x2.
My ath9k-sourced AR_SREV_OWL_<X> macros were thus using the wrong
silicon revision values and wouldn't correctly match.
This commit does a few things:
* Change the AR_SREV_OWL_<x> macros to use the AR_SREV_REVISION_OWL_*
values, not AR_XSREV_REVISION_OWL macros;
* Disable AR_XSREV_REVISION_OWL_* values;
* Modify the IS_5416 to properly check the MAC is OWL, rather than
potentially matching on non-OWL revisions (which shouldn't happen
unless there's a silicon revision of higher than 0x9 in a later
chip..)
* Add a couple more macros from the Atheros HAL for compatibility.
The main difference now is that the Atheros HAL defines
AR_SREV_OWL_{20,22}_OR_LATER subtly differently - it fails on all HOWL
silicon. The AR_SREV_5416_*_OR_LATER macros match on the relevant OWL
version -and- all HOWL versions, along with subsequent versions.
A subsequent commit is going to migrate the uses of AR_SREV_OWL_X_OR_LATER
to AR_SREV_5416_X_OR_LATER to match what's going on in the Atheros HAL.
There's only two uses of AR_SREV_OWL_X_OR_LATER which currently don't
apply to FreeBSD but it may do in the future.
Yes, it's all confusing!
Quoting the ath9k commit message:
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Reference: https://patchwork.kernel.org/patch/753862/
Obtained from: Linux ath9k
The checks should function as follows:
* AR_SREV_<silicon> : check macVersion matches that version id
* AR_SREV_<silicon>_<revision> : check macVersion and macRevision match
the version / revision respectively
* AR_SREV_<silicon>_<revision>_OR_LATER: check that
+ if the chip silicon version == macVersion, enforce revision >= macRevision
+ if the chip silicon version > macVersion, allow it.
For example, AR_SREV_MERLIN() only matches AR9280 (any revision),
AR_SREV_MERLIN_10() would only match AR9280 version 1.0, but
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 version >= 2.0 _AND_
any subsequent MAC (So AR9285, AR9287, etc.)
The specific fixes which may impact users:
* if there is Merlin hardware > revision 2.0, it'll now be correctly
matched by AR_SREV_MERLIN_20_OR_LATER() - the older code simply
would match on either Merlin 2.0 or a subsequent MAC (AR9285, AR9287, etc.)
* Kite version 1.1/1.2 should now correctly match. As these macros
are used in the AR9285 reset/attach path, and it's assumed that the
hardware is kite anyway, the behaviour shouldn't change. It'll only
change if these macros are used in other codepaths shared with
older silicon.
Obtained from: Linux ath9k, Atheros
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
Writing the TX power registers is the same between all of these chips
and later NICs (AR9287, AR9271 USB, etc.) so this will reduce code
duplication when those NICs are added to the HAL.
spurious (and fatal) interrupt errors.
One user reported seeing this:
Apr 22 18:04:24 ceres kernel: ar5416GetPendingInterrupts: fatal error,
ISR_RAC 0x0 SYNC_CAUSE 0x2000
SYNC_CAUSE of 0x2000 is AR_INTR_SYNC_LOCAL_TIMEOUT which is a bus timeout;
this shouldn't cause HAL_INT_FATAL to be set.
After checking out ath9k, ath9k_ar9002_hw_get_isr() clears (*masked)
before continuing, regardless of whether any bits in the ISR registers
are set. So if AR_INTR_SYNC_CAUSE is set to something that isn't
treated as fatal, and AR_ISR isn't read or is read and is 0, then
(*masked) wouldn't be cleared. Thus any of the existing bits set
that were passed in would be preserved in the output.
The caller in if_ath - ath_intr() - wasn't setting the masked value
to 0 before calling ath_hal_getisr(), so anything that was present
in that uninitialised variable would be preserved in the case above
of AR_ISR=0, AR_INTR_SYNC_CAUSE != 0; and if the HAL_INT_FATAL bit
was set, a fatal condition would be interpreted and the chip was
reset.
This patch does the following:
* ath_intr() - set masked to 0 before calling ath_hal_getisr();
* ar5416GetPendingInterrupts() - clear (*masked) before processing
continues; so if the interrupt source is AR_INTR_SYNC_CAUSE
and it isn't fatal, the hardware isn't reset via returning
HAL_INT_FATAL.
This doesn't fix any underlying errors which trigger
AR_INTR_SYNC_LOCAL_TIMEOUT - which is a bus timeout of some
sort - so that likely should be further investigated.
It's also marked inactive by the initvals, and enabled after
the baseband/PLL has been configured, but before the RF
registers have been programmed.
The origin and reason for this particular change is currently unknown.
Obtained from: Linux ath9k
Antenna diversity on the >= AR5416 is implemented differently than the
AR5212 and previous chips. So for now, and not to confuse things, just
disable it for now.
upper-level HAL.
Right now the per-chain noise floor values aren't used anywhere in
the upper-level HAL, so the driver currently has no real reference
to compare the per-chain RSSI values to.
This is needed before per-chain RSSI values (for ctl and ext radios)
are can be thrown upstairs to the net80211 code.
From the ath9k source:
==
11N: we can no longer afford to self link the last descriptor.
MAC acknowledges BA status as long as it copies frames to host
buffer (or rx fifo). This can incorrectly acknowledge packets
to a sender if last desc is self-linked.
==
Since this is useful for pre-AR5416 chips that communicate PHY errors
via error frames rather than by on-chip counters, leave the support
in there, but disable it for AR5416 and later.
the AR9285 so I'll leave it off for that.
Ath9k sources indiciate that one of the ANI modes interferes with
RIFS detection, so match ath9k and disable that.
* The existing interrupt mitigation code didn't mitigate anything - the
per-packet TX/RX interrupts are still occuring. It's possible this
worked for the AR5416 but not any later chipsets; I'll investigate and
update as needed.
* Set both the RX and TX threshold registers whilst I'm at it.
This is verified to work on the AR9220 and AR9160. I'm leaving it off
by default in case it's truely broken, but I need to have it enabled
when doing 11n testing or interrupt loads exceed 10,000 interrupts/sec.
At least one AR5416 user has reported measurable throughput drops
with this option. For now, disable it and make it a run-time
twiddle. It won't take affect until the next radio programming
trip though (eg channel scan, channel change.)
so there's no need to enable the RX of invalid frames just to do ANI.
The if_ath code and AR5212 ANI code setup the RX filter bits to enable
receiving OFDM/CCK errors if the device doesn't have the hardware
MIB counters. It isn't initialising it for the AR5416+ because all of
those chips have hardware MIB counters.
This fixes the odd (and performance affecting!) situation where if ani
is enabled (via sysctl dev.ath.X.intmit) then suddenly there's be a very
large volume of phy errors - which is good to track, but not what was
intended. Since each PHY error is a received (0 length) frame, it can
significantly tie up the RX side of things.
This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.
The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.
The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.
Obtained From: Linux ath9k
I found this when trying to figure out why the RX PHY error count
didn't match the OFDM error count ANI was using. It turns out
there was two problems:
* What this commit addresses - using the wrong mask for OFDM errors,
and
* The RX filter is set incorrectly after a channel scan (at least)
even if interference mitigation is enabled by default.
ANI is still disabled by default for the AR5416 and later chips.
bring it in line with the rest of the register initialisation.
I've verified that the 2/5ghz board values written to the
chip match what was previously written.
* add pspoll/uapsd queue setup defaults;
* enable the exponential backoff window rather than the random
backoff window when doing TX contention management.
Give it a good go (32 attempts) and then print out a warning that's
going to occur whether HAL debugging is enabled or not. Then don't
abort the radio setup; just continue merrily along.
This should fix the issue that users were having where scanning would
occasionally fail on the active channel, causing traffic to cease
until the radio scanned again.
not needed.
These calibrations are only applicable if the chip operating mode
engages both interleaved RX ADCs (ie, it's compensating for the
differences in DC gain and DC offset -between- the two ADCs.)
Otherwise the chip reads values of 0x0 for the secondary ADC
(as I guess it's not enabled here) and thus writes potentially
bogus info into the chip.
I've tested this on the AR9160 and AR9280; both behave themselves
in 11g mode with these calibrations disabled.
for fixing them based on the ath9k related TXQ fixes.
I've done this so people can go over the history of the diffs to the original
AR5212 routines (which AR5416 and later chips use) to see what's changed.
This commit really is "fix the OFDM duration calculation to match reality when
running in 802.11g mode."
The AR5212 init vals set AR_MISC_MODE to 0x0 and all the bits that can be set are
set through code.
The AR5416 and later initvals set AR_MISC_MODE to various other values (with
the AR5212 AR_MISC_MODE options cleared), which include AR_PCU_CCK_SIFS_MODE .
This adds 6uS to SIFS on non-CCK frames when transmitting.
This fixes the issue where _DATA_ 802.11g OFDM frames were being TX'ed with
the ACK duration set to 38uS, not 44uS as on the AR5212 (and other devices.)
The AR5212 TX pathway obeys the software-programmed duration field in the packet,
but the 11n TX pathway overrides that with a hardware-calculated duration. This
was getting it wrong because of the above AR_MISC_MODE setting. I've verified
that 11g data OFDM frames are now being TXed with the correct ACK+SIFS duration
programmed in.
Since ath9k does some slightly different bit fiddling when setting up
the TX queues, it may that the TX queue setup/reset functions will need
overriding later on.
The offsets didn't match the assumption that nfarray[] is ordered by the
chainmask bits and programmed via the register order in ar5416_cca_regs[].
This repairs that damage and ensures that chain 1 is programmed correctly.
(And extension channels will now be programmed correctly also.)
This fixes some of the stuck beacons I've been seeing on my AR9160/AR5416
setups - because Chain 1 would be programmed -80 or -85 dBm, which is
higher than the actual noise floor and thus convincing the radio that
indeed it can't ever transmit.
rather than duplicating them for the v14 (ar5416+) and v4k (ar9285) codebases.
Further chipsets (eg the AR9287) have yet another EEPROM format which will use
these routines to calculate things.
to the TX closed-loop power control registers.
* Modify a couple of functions to take the register chain number,
rather than the regChainOffset value. This allows for the
register chain to be logged.
this is incorrect for Kite (AR9285) and any future chipsets that
override the EEPROM related routines.
It meant that a direct call to set the TX power would call the v14 EEPROM
AR5416/AR9280 calibration routines, rather than the v4k EEPROM routines
for the AR9285. It thus read the incorrect values from the EEPROM and
programmed garbage PDADC and TX power values into the hardware.