vm_mtx does not recurse and is required for most low level
vm operations.
faults can not be taken without holding Giant.
Memory subsystems can now call the base page allocators safely.
Almost all atomic ops were removed as they are covered under the
vm mutex.
Alpha and ia64 now need to catch up to i386's trap handlers.
FFS and NFS have been tested, other filesystems will need minor
changes (grabbing the vm lock when twiddling page properties).
Reviewed (partially) by: jake, jhb
of the pcic class of devices. Go ahead and move it to the "usual"
place. I say "usual" in quotes since it isn't exactly right (not in
dev/blah), but it is closer than before.
much more often that expected and negatively impact performance when
running at 100mbps. I need to figure out if there's a better way to
handle this, but for now this shouldn't hurt anything.
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
The constant I was using was correct, but I mislabeled it as 256K when
it should have been 512K. This doesn't actually change the code, but
it clarifies things somewhat.
Submitted by: Chuck Cranor <chuck@research.att.com>
parts. This is based on the newcard code that turns it off :-). We
can now reboot after NEWCARD or Windows and have OLDCARD work. Add
support for the RL5C466 while I'm at it.
Treat TI1031 the same as the CLPD6832. It doesn't work yet, but sucks
less than it did before.
Also add a few #defines for other changes in the pipe.
1. Pick up MII/PHY support for Livengood copper part (10/100/1000) from
Parag Patel. It was a fairly complete but not quite platform independent
job.
2. Finish silly offset differences that LIVENGOOD vs. WISEMAN registers
have (so the !)$*!)$*!$ fiber LIVENGOOD now works too).
3. Ansify the source.
So- we now suppor tthe PRO1000F and PRO1000T adapters.
1. The offsets for some registers change in LIVENGOOD. Gratuitously.
2. Define LIVENGOOD and LIVENGOOD_CU part numbers. Add some more
specific LIVENGOOD defaults.
3. Add definitions for PHY support for the copper LIVENGOOD part
(10/100/1000).
interface on this chip is compatable with the PIIX4. The catch is that
this interferes with isab0 which wants to attach to the same PCI node.
It seems to work, but we only tested it on systems with no ISA cards.
in vr_init(). The VIA Rhine chip happens to be able to automatically
read its station address from the EEPROM automatically when reset,
so you don't need to program the filter if you want to keep using the
factory default address, but if you want to change it with "ifconfig vr0
ether xx:xx:xx:xx:xx:xx" then we need to manually set it in the init
routine.
in VMware reports 0x00000000 in the PCI subsystem ID register, but
0x10001000 when you read the mirror registers in I/O space. This causes
pcn_probe() to think it's found a card in 32-bit mode, and performing
a 32-bit I/O access makes on a 16-bit port makes VMware go boom. Special
case the 0x10001000 value until somebody at VMware grows a clue.
Finally discovered by: Andrew Gallatin
- Use pci_get_powerstate()/pci_set_powerstate() in all the other drivers
that need them so we don't have to fiddle with the PCI power management
registers directly.
- Use pci_enable_busmaster()/pci_enable_io() to turn on busmastering and
PIO/memory mapped accesses.
- Add support to the RealTek driver for the D-Link DFE-530TX+ which has
a RealTek 8139 with its own PCI ID. (Submitted by Jason Wright)
- Have the SiS 900/National DP83815 driver be sure to disable PME
mode in sis_reset(). This apparently fixes a problem on some
motherboards where the DP83815 chip fails to receive packets.
(Submitted by Chuck McCrobie <mccrobie@cablespeed.com>)
case there is nothing to do. This happens normally when the card shares
the interrupt line with other devices.
This code saves a couple of microseconds per interrupt even on a
fast CPU. You normally would not care, except under heavy tinygram
traffic where you can have some 50-100.000 interrupts per second...
On passing, correct a spelling error.
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
chipset. The MAC address is stored in the APC CMOS RAM and we have to
commit trememdous evil in order to read it. The code to do this is only
activated on the i386 platform. Thanks to Cameron Grant for providing
access to a test box for me to tinker with.
This will fix the problem where the sis driver ends up with a station
address of 00:00:00:00:00:00 on boards that use the 630E chipset.
an override as a loader settable variable (fxp_iomap). fxp_iomap is
a bitmap of fxp units that should be configured to use PCI I/O space
in stead of PCI Memory space.
Reviewed by: Kees Jan Koster <dutchman@tccn.cs.kun.nl>, dg@freebsd.org
MFC'ed i due time. I can't test it under current right now because
netgraph seems to do unethical things with mutexes.
musycc:
Add status per channel.
Reduce printf chattyness
Keep error counters line if_mn does.
Increase descriptor count.
if_mn:
Support experimental unframed E1 lines.
These two drivers should share more code relating to framed channelized
TDM media in general (T1/E1/E3/T3, Sonet). Anyone interested email me.
if_vr: handle the case where vr_encap() returns failure: bust out of the
packet sending loop instead of panicking. Also add some missing
newlines to some printf()s.
if_dc: The miibus_read and miibus_write methods keep swapping in and
out of MII mode by fiddling with CSR6 for cards with MII PHYs.
This is a hack to support the original Macronix 98713 card which
has built-in NWAY that uses an MII-like management interface
even though it uses serial transceivers. Conditionalize this
so that we only do this on 98713 chips, since it does bad things
to genuine tulip chips (and maybe other clones).
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
This is because calls with M_WAIT (now M_TRYWAIT) may not wait
forever when nothing is available for allocation, and may end up
returning NULL. Hopefully we now communicate more of the right thing
to developers and make it very clear that it's necessary to check whether
calls with M_(TRY)WAIT also resulted in a failed allocation.
M_TRYWAIT basically means "try harder, block if necessary, but don't
necessarily wait forever." The time spent blocking is tunable with
the kern.ipc.mbuf_wait sysctl.
M_WAIT is now deprecated but still defined for the next little while.
* Fix a typo in a comment in mbuf.h
* Fix some code that was actually passing the mbuf subsystem's M_WAIT to
malloc(). Made it pass M_WAITOK instead. If we were ever to redefine the
value of the M_WAIT flag, this could have became a big problem.
claimed that their Intel NIC is comatose after a warm boot from Windoze.
This is most likely due to the card getting put in the D3 state. This
should bring it back to life.
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.
I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
- Break out the /dev/pci driver into a separate file.
- Kill the COMPAT_OLDPCI support.
- Make the EISA bridge attach a bit more like the old code; explicitly
check for the existence of eisa0/isa0 and only attach if they don't
already exist. Only make one bus_generic_attach() pass over the
bridge, once both busses are attached. Note that the stupid Intel
bridge's class is entirely unpredictable.
- Add prototypes and re-layout the core PCI modules in line with
current coding standards (not a major whitespace change, just moving
the module data to the top of the file).
- Remove redundant type-2 bridge support from the core PCI code; the
PCI-CardBus code does this itself internally. Remove the now
entirely redundant header-class-specific support, as well as the
secondary and subordinate bus number fields. These are bridge
attributes now.
- Add support for PCI Extended Capabilities.
- Add support for PCI Power Management. The interface currently
allows a driver to query and set the power state of a device.
- Add helper functions to allow drivers to enable/disable busmastering
and the decoding of I/O and memory ranges.
- Use PCI_SLOTMAX and PCI_FUNCMAX rather than magic numbers in some
places.
- Make the PCI-PCI bridge code a little more paranoid about valid
I/O and memory decodes.
- Add some more PCI register definitions for the command and status
registers. Correct another bogus definition for type-1 bridges.
This clears out my outstanding netgraph changes.
There is a netgraph change of design in the offing and this is to some
extent a superset of soem of the new functionality and some of the old
functionality that may be removed.
This code works as before, but allows some new features that I want to
work with and evaluate. It is the basis for a version of netgraph
with integral locking for SMP use.
This is running on my test machine with no new problems :-)
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
place the LOCKing macros within the areas within if_wxvar.h that
is set aside for them. Put any platform specific data also in those
areas.
For ease of maintenance purposes, merge in the OpenBSD version codebase here.
on. So stop failing the attach if the IRQ is unassigned. With this
patch, I can now boot with PNP-OS YES in my BIOS no differently than
PNP-OS NO (which is a good thing since Windows hangs with PNP-OS NO).
Obtained from: msmith
like the args to the config space accessors these functions replaced.
This reduces the likelyhood of overflow when the args are used in
macros on the alpha. This prevents memory management faults when
probing the pci bus on sables, multias and nonames.
Approved by: dfr
Tested by: Bernd Walter <ticso@cicely8.cicely.de>
the interface to use callout_* instead of timeout(). Also add an
IS_MPSAFE #define (currently off) which will mark the driver as mpsafe
to the upper layers.
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
(identified by the IO map being 256 bytes long instead of 128)
This chip works very unreliably on my Lanner embedded PC with the rl driver.
Lots of watchdog timeouts or poor performance.
Forcing the media type to 10 Meg (ifconfig rl0 media 10baseT/UTP) is a good
workaround.
This looks very similar to the problem reported in PR kern/18790
It is interesting to note that the linux driver has lots of special
case code for this chip.
is already in 32-bit mode, we need to be able to detect this and still
read the chip ID code. Detecting 32-bit mode is actually a little
tricky, since we want to avoid turning it on accidentally. The easiest
way to do it is to just try and read the PCI subsystem ID from the
bus control registers using 16-bit accesses and compare that with the
value read from PCI config space. If they match, then we know we're in
16-bit mode, otherwise we assume 32-bit mode.
16-bit mode. Technically, pcn_probe() is destructive because once the
chip goes into 32-bit mode, the only way to get it out again is a
hardware reset. And once the device is in 32-bit mode, the lnc driver
won't be able to talk to it. So if pcn_probe() is called before the
lnc probe routine, and pcn_probe() rejects the chip as one it doesn't
support, the lnc driver will be SOL.
I don't like this. I think it's a design flaw that you can't switch
the chip out of 32-bit mode once it's selected. The only 'right'
solution is for the pcn driver to support all of the PCI devices
in 32-bit mode, however I don't have samples of all the PCnet series
cards for testing.
pollution in <sys/mutex.h>. This was half fixed in rev.1.3 of
midwayreg.h. The pollution exposed the bug that this driver was using
toy versions of the bus space macros under FreeBSD. Disabling the
toy versions made this driver compile but dependent on the pollution.
There was still a toy version of bus_space_read_1() in unreachable code.
and nobroadcast bits in the mode register and call it both from
pcn_init() and pcn_ioctl(). Sometimes we need to force the state
of the nobroadcast bit after switching out of promisc mode.
them. If we leave garbage in them, the dc_apply_fixup() routine may
try to follow bogus pointers when applying the reset fixup.
Noticed by: Andrew Gallatin
- Add DRIVER_MODULE() declaration to make this driver a
child of cardbus
- Handle different width EEPROMs
The CIS parser still barfs when scanning this card, but it seems to
probe/attach correctly anyway. I can't do a traffic test just yet
since I don't have a proper crossover cable handy.
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
command register is too aggressive. Revert to the previous behaviour, but
leave the new behaviour available as an undocumented option. It's not
clear what the Right, Right Thing is to do here, but the more conservative
approach is safer.
a RealTek 8139 cardbus device. Unfortunately it doesn't quite work yet
because the CIS parser barfs on it.
Submitted by msmith, with some small tweaks by me.
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
the PCI latency timer value to 0x80. Davicom's Linux driver does this,
and it drastically reduces the number of TX underruns in my tests. (Note:
this is done only for the Davicom chips. I'm not sure it's a good idea to
do it for all of them.)
Again, still waiting on confirmation before merging to stable.
DM9100/DM9102 chips. Do not set DC_TX_ONE. The DC_TX_USE_TX_INTR flag
causes dc_encap() to set the 'interrupt on TX completion' bit only
once every 64 packets. This is an attempt to reduce the number
of interrupts generated by the chip. You're supposed to get a 'no more
TX buffers left' interrupt once you hit the last packet whether you
ask for one or not, however it seems the Davicom chip doesn't generate
this interrupt, or at least it doesn't generate it under the same
circumstances. The result is that if you transmit n packets, where
n is less than 64, and then wait 5 seconds, you'll get a watchdog
timeout whether you want one or not. The DC_TX_INTR_ALWAYS causes
dc_encap() to request an interrupt for every frame.
I'm still waiting on confirmation from a couple of users to see if this
fixes their problems with the Davicom DM9102 before I merge this into
-stable, but this fixed the problem for me in my own testing so I'm
willing to make the change to -current right away.
Have if_ti stop "hiding" the softc pointer in the buffer region. Rather,
use the available void * passed to the free routine and pass the softc
pointer through there.
To note: in MEXTADD(), TI_JUMBO_FRAMELEN should probably be TI_JLEN. I left it
unchanged, because this way I'm sure to not damage anything in this respect...
This commit adds support for Xircom X3201 based cardbus cards.
Support for the TDK 78Q2120 MII is also added.
IBM Etherjet, Intel and Xircom cards uses these chips.
Note that as a result of this commit, some Intel/DEC 21143 based cardbus
cards will also attach, but not get link. That is being looked at.
rather than all the flags. This prevents setting being read from ROM,
which is a problem. If this breaks anything, it will only break the
3C556B cards minipci cards, which mainly exist at rpi as far as rpi
has been able to tell.
Submitted by: Louis Gerbarg <gerbal@rpi.edu>
#ifdef away the offending code until somebody with more newbus fu than
me can figure out where to put a default function that returns 255
without touching each alpha chipset driver..
takes care of all the 10/100 and gigE PCI drivers that I've done.
Next will be the wireless drivers, then the USB ones. I may pick up
some stragglers along the way. I'm sort of playing this by ear: if
anyone spots any places where I've screwed up horribly, please let me
know.
of the Am79c973 with "AlertIT Technology," whatever that is. Also mention
support for the PCnet/FAST III cards in the documentation. The
PCnet/FAST III chips have integrated 10/100 PHYs.
adapters. This is necessary in order to make this driver work with
the built-in ethernet on the alpha Miata machines. These systems
have a 21143-PC chip on-board and optional daughtercards with either
a 10/100 MII transceiver or a 10baseT/10base2 transceiver. In both
cases, you need to twiddle the GPIO bits on the controller in order
to turn the transceivers on, and you have to read the media info
from the SROM in order to find out what bits to twiddle.
Add lockdestroy() and appropriate invocations, which corresponds to
lockinit() and must be called to clean up after a lockmgr lock is no
longer needed.
this just involves adding the chip ID to the supported list: the PCnet/PRO
is compatible with the PCnet/FAST+ and friends and should "just work"
with this driver.
Also try to handle mbuf allocation failures in the receive handler
more gracefully.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
a result of mii_phy_probe()) and use that rather than hardcoding a
constant. The hardcoded way was too specific to the particular card
I had and caused PHY probing to fail on at least one laptop with a
built-in AMD chip.
Reported by: rjk@grauel.com (Richard J Kuhns)
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
is enabling as all entries are still called with Giant being held.
Maintaining compatability with NetBSD makes what should be very simple
kinda ugly.
Reviewed by: Jason Evans
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
on the NEC VersaPro NoteBook PC. This 21143 implementation has no LEDs,
and flipping the LED control bits somehow stops it from establishing
a link. We check the subsystem ID and don't flip the LED control
bits for the NEC NIC.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
bus/slot/function numbers. The old PCI code used other markers or
something, but without it here under the new pci code it is very hard to
tell which device is which (this only affects bootverbose mode).
In the nexus case, there are no ivars for children of nexus devices,
and we were passing data in from before the device existed, hence ivars
are convenient as the softc doesn't really exist yet.
However, for pci->pci bridges, the pcib occupies a pci device itself,
which *does* already have ivars. However, softc is available and stable
at this point since we've been identified and are locating the bus during
attach. So, use softc for this version of pcib devices for storing the
physical bus number in.
the link and activity LED control bits in CSR15 in order for the
controller to drive the LEDs correctly. This was largely done for the
ZNYX multiport cards, but should also work with the DEC DE500-BA
and other non-MII cards.
enable bit hasn't been set in the command register, set the bit and
honour the register. It seems that quite a few lazy BIOS writers
aren't bothering to do this, which upsets the existing code and causes
us to miss out on properly-configured devices.
pcib_set_bus() cannot be used on the new child because it is
meant to be used on the *pci* device (it looks at the parent internally)
not the pcib being added. Bite the bullet and use ivars for the bus
number to avoid any doubts about whether the softc is consistant between
probe and attach. This should not break the Alpha code.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
laptops. I've checked that this still works with the other cards and
it works with the 3c556 that I have access to, but I want to check that
it works with the 556B mentioned in PR #20878 before I close out the PR
and merge to -stable.
- Modify the driver to poll the link state and positively set the
MAC to full or half duplex as needed. Previously, it was possible
for the MAC to remain in half duplex even though the PHY had negotiated
full duplex with its link partner, which would result in bursty
performance.
- Program some of the NatSemi's registers as specified by the datasheet.
The manual says these are necessary for "optimum perofrmance," though
a couple of them are marked as reserved in the register map. *shrug*
- Select the TX DMA burst size correctly for 10 and 100mbps modes.
Previously I was using 64 bytes in both modes, which worked in
100mbps mode, but resulting in spotty performance in 10mbps.
32 bytes works much better; without this change, the natsemi
chip yields piss poor performance at 10mbps.
With these fixes, the NatSemi chip finally performs to my satisfaction.
I should be merging the support for this controller into -stable shortly.
Phew.
that should be better.
The old code counted references to mbuf clusters by using the offset
of the cluster from the start of memory allocated for mbufs and
clusters as an index into an array of chars, which did the reference
counting. If the external storage was not a cluster then reference
counting had to be done by the code using that external storage.
NetBSD's system of linked lists of mbufs was cosidered, but Alfred
felt it would have locking issues when the kernel was made more
SMP friendly.
The system implimented uses a pool of unions to track external
storage. The union contains an int for counting the references and
a pointer for forming a free list. The reference counts are
incremented and decremented atomically and so should be SMP friendly.
This system can track reference counts for any sort of external
storage.
Access to the reference counting stuff is now through macros defined
in mbuf.h, so it should be easier to make changes to the system in
the future.
The possibility of storing the reference count in one of the
referencing mbufs was considered, but was rejected 'cos it would
often leave extra mbufs allocated. Storing the reference count in
the cluster was also considered, but because the external storage
may not be a cluster this isn't an option.
The size of the pool of reference counters is available in the
stats provided by "netstat -m".
PR: 19866
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: alfred (glanced at by others on -net)
understand exactly what it is about SMPng that tickles this bug. What I
do know is that the foo_init() routine in most drivers is often called
twice when an interface is brought up. One time is due to the ifconfig(8)
command calling the SIOCSIFFLAGS ioctl to set the IFF_UP flag, and another
is probably due to the kernel calling ifp->if_init at some point. In any
case, the SMPng changes seem to affect the timing of these two events in
such a way that there is a significant delay before any packets are sent
onto the wire after the interface is first brought up. This manifested
itself locally as an SMPng test machine which failed to obtain an address
via DHCP when booting up.
It looks like the second call to fxp_init() is happening faster now than
it did before, and I think it catches the chip while it's in the process
of dealing with the configuration command from the first call. Whatever
the case, a FXP_CSR_SCB_CNA interrupt event is now generated shortly after
the second fxp_init() call. (This interrupt is apparently never generated
by a non-SMPng kernel, so nobody noticed.)
There are two problems with this: first, fxp_intr() does not handle the
FXP_CSR_SCB_CNA interrupt event (it never tests for it or does anything
to deal with it), and second, the meaning of FXP_CSR_SCB_CNA is not
documented in the driver. (Apparently it means "command unit not active.")
Bad coder. No biscuit.
The fix is to have the FXP_CSR_SCB_CNA interrupt handled just like the
FXP_SCB_STATACK_CXTNO interrupt. This prevents the state machine for
the configuration/RX filter programming stuff from getting wedged for
several seconds and preventing packet transmission.
Noticed by: jhb
if you kldload this driver, all the subordinate devices are probed/attached
as expected. But this is not the case when the driver is statically compiled
into the kernel. Since I do most of my testing with modules, I failed to
notice this. I'm not sure if it's intended behavior or not. I think it may
be, but it seems a little counter-intuitive.
with LEDs on some cards being stomped on when clearing the "jabber disable"
bit. Using DC_SETBIT() has an unwanted side effect of setting a write enable
bit in the watchdog timer register which we really want to be cleared when
we do a write.
This is in fact an Intel Orion chipset (82454KX/GX) which has been used
in HP NetServer's LS4 range.
HP Probably relabeled the DID. That's the only explanation I can find
plausible to this `mystery'.
the 12.4.11 firmware with a few changes to the link handling code merged
in from the 12.4.13 release. I'm doing this because the 12.4.13 firmware
doesn't seem to handle 10/100 link settings properly on 1000baseT cards.
Note that the revision codes still identify the firmware as 12.4.13
because both ti_fw2.h and ti_fw.h have to have the same revision values,
and I wanted to keep the 12.4.13 firmware for Tigon 1 cards.
It's nice to have firmware source.
cards. This basically involves switching to the 12.4.13 firmware, plus
a couple of minor tweaks to the driver.
Also changed the jumbo buffer allocation scheme just a little to avoid
'failed to allocate jumbo buffer' conditions in certain cases.
lock up under moderate to heavy load.
The status & command fields share a 32-bit longword. The programming
API of the eepro apparently requires that you update the command field
of a transmit slot that you've already given to the card. This means
the card could be updating the status field of the same longword at
the same time. Since alphas can only operate on 32-bit chunks of
memory, both the status & command fields are loaded from memory &
operated on in registers when the following line of C is executed:
sc->cbl_last->cb_command &= ~FXP_CB_COMMAND_S;
The race is caused by the card DMA'ing up the status at just the wrong
time -- after it has been loaded into a register & before it has been
written back. The old value of the status is written back, clobbering
the status the card just DMA'ed up. The fact that the card has sent
this frame is missed & the transmit engine appears to hang.
Luckily, as numerous people on the freebsd-alpha list pointed out, the
load-locked/store-conditional instructions used by the atomic
functions work with respect changes in memory due to I/O devices. We
now use them to safely update the command field.
Tested by: Bernd Walter <ticso@mail.cicely.de>
3.3volt PCI/cardbus chipsets similar to the 98715 (and they have
512-bit hash tables). Also update the man page to mention the 98727/98732
and the SOHOware SFA110A Rev B4 card with the 98715AEC-C chip.
which differ slightly from the Macronix MX98715AEC chip on the sample
adapter that I have in that the multicast hash table is only 128 bits
wide instead of 512. New adapters are popping up with this chip, and
due to improper handling of the smaller hash table, broadcast packets
were not being received correctly.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
associated patch to XFree86 allows the X server to work with this chipset
on FreeBSD. Additional work will include porting the Linux 3D driver.
Submitted by: Ruslan Ermilov <ru@FreeBSD.org>
controller chip. This chip is currently being used on the NetGear
FA312-TX adapter, which I guess is a replacement for the FA310-TX
(PNIC-based).
I added support for this chip by modifying the sis driver since
the SiS 900 and the NS DP83815 have almost the same programming
interface (the RX filter programming and PHY access methods are
different, but the general configuration, DMA scheme and register
layout are identical).
I would have had this done a lot sooner, but getting the damn MAC
address out of the EEPROM proved to be more complicated than expected.
the message to indicate that it could also be a disconnected cable, and
return okay from wx_hw_intialize *anyway*. This allows us to contineu to
set the station address and when we do get link up, we're ready to roll.
Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.
21143 chips, I accidentally removed the DC_MII_REDUCED_POLL flag
for all 21143 cards. This caused problems with timer-instigated
TCP retransmits, which happened to occur at the same time as an
MII poll tick on MII-based cards (e.g. D-Link DFE-570TX). Fixed this,
plus made some other cleanups. The autoneg fixes for the non-MII
cards still work. Also tested the PNIC II now that I have one again.
after autoneg so we make sure to set the link state and duplex mode
correctly.
- Make sure to set the 'ignore pause frames' bit on the XMAC.
- Small linewrap fix.
workalike chips (Macronix 98713A/98715 and PNIC II). Timing is somewhat
critical: you need to bring the link as soon as possible after NWAY
is done, and the old one second polling interval was too long. Now
we poll every 10th of a second until NWAY completes (at which point
we return to the 1 second interval again to keep an eye on the link
state).
I tested all the other cards I had on hand to make sure I didn't bust
any of them and they seem to work (including the MII-based 21143 card).
This should fix some autoneg problems with DE500-BA cards and the
built-in 10/100 ethernet on some alpha systems.
(Now before anyone asks why I never noticed this before, the old code
worked just find with the Intel swich I used for testing back in NY.
Apparently not all switches are as picky about the timing.)
"options COMPAT_OLDPCI". This option already existed, but now also tidies
up the declarations in #include <pci/pci*.h>. It is amazing how much stuff
was using the old pre-FreeBSD 3.x names and going silently undetected.
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
for transmit to the adapter, not when we receive a transmit interrupt
indicating that they were sent. This fix now allows tcpdump to produce
sane results by recording the timestamp at the point where the mbuf was
actually transmitted.
the case where we receive a packet that wraps from the end of the
RX buffer back to the start. This fixes an unaligned access trap on
the alpha with NFS.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
- Break out the support for the XMAC II's PHY into an miibus driver.
- Reorganize the probe/attach stuff using newbus. Each XMAC is now
attached to the parent GEnesis controller using newbus. This is
necessary since each XMAC must also have an attached miibus, and
the miibus read/write register routines need to be able to get
at the softc struct for each XMAC, not the one for the parent
controller. This allows me to get rid of the grotty code I added
for selecting the unit numbers for the ifnet interfaces: the unit
numbers are now derived from the newbus-assigned unit numbers,
which should track with the ifnet interface numbers. I think.
At the very least, there should never be any collisions.
- Add support for the SK-9821 and SK-9822 1000baseTX adapters. Special
thanks to SysKonnect for loaning me two adapters for testing.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
This don't hurt anything.
PCI/CardBus Bridge -> PCI-CardBus Bridge
Submitted by: Takeshi Shibagaki <sibagaki@lsi.melco.co.jp>
Obtained from: bsd-nomads ML in Japan
- Only call m_pullup() when necessary.
- Check return value from rl_encap() in rl_start() to avoid panic when
we run out of mbufs. (Fixes PR kern/17582)
PR: kern/17582
address size that is different than the standard 6bits. This fixes
support for the Compaq NC3121 card, certain newer Intel Pro/100+
cards, and should also fix integrated NICs on SuperMicro and Compaq
motherboards.
The auto-sizing algorithm was taken from NetBSD (thanks!), which I
think got it from Linux originally.
Thanks also to Andrew Sparrow <spadger@best.com> and Joe Moore
<jomor@ahpcns.com> for supplying me with unworking Compaq and Intel
cards to develop and test the fixes with.
cardbus bridge init routine for all cardbuses. This routine attempts
to compensate for BIOSes that do not setup the cardbus bridge into
legacy mode. Since this is becoming more common, and cardbus pci
cards have appeared on the market, this makes sense.
Do some TI113x specific initialization. This came in as part of the
patch. Report TI1[1234]XX specific config registers protected by
bootverbose.
Minor code cleanup while I'm here. I've also removed the unused code
present in the original patches, and cleaned it up slightly in places
as well.
The original patches supported more than one card, but these patches
support just one. We should likely revisit this in the future.
This makes the Compaq card that Walnut Creek CD purchased for me work
in my bouncer box.
This is a MFC candidate. However, I'd like to get some airtime on
these patches on as many laptops as possible before doing the MFC. It
does change things somewhat. In theory, apart from the minor TI
tweaks, this shouldn't change anything if the bridge is in legacy mode
already.
Submitted by: sanpei@sanpei.org (MIHIRA Yoshiro)
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
