Allow changing the trampoline ABI with makeoptions, this will allow
us to have a trampoline with a different ABI from the kernel.
Useful in cases where we have to boot a 64 bit kernel from a
bootloader which supports only 32 bit or vice versa.
Approved by: bz(re), jmallett, imp
mask bits to control register and control bits to mask register.
The former causes ICW1_RESET|ICW1_LTIM combination to be written to
control register, which on QEMU results in "level sensitive irq not
supported" error.
Submitted by: Robert Millan <rmh@debian.org>
option to vm_object_page_remove() asserts that the specified range of pages
is not mapped, or more precisely that none of these pages have any managed
mappings. Thus, vm_object_page_remove() need not call pmap_remove_all() on
the pages.
This change not only saves time by eliminating pointless calls to
pmap_remove_all(), but it also eliminates an inconsistency in the use of
pmap_remove_all() versus related functions, like pmap_remove_write(). It
eliminates harmless but pointless calls to pmap_remove_all() that were being
performed on PG_UNMANAGED pages.
Update all of the existing assertions on pmap_remove_all() to reflect this
change.
Reviewed by: kib
signalled when the attribute address for the CF is 0 in the octeon
sysinfo structure. In this mode, the DATA port is 16-bits, but the
other ports are 8-bits, but on a 16-bit bus (so you have to access it
a short at a time, but only believe the lower byte). See the code for
more details on this slightly odd arrangement. I'm still not 100%
happy with the abstractions here on many levels (starting with the
globals for these settings, on down to no bus_space use, etc), but the
driver had these problems before the change.
Also, clean up the code a bit to make this support easier, and the
code a bit easier to read. I tried to follow existing style, but may
have missed a few spots. Add some comments.
Fix probe/attach routine to return a proper error for the simulator.
With this change, my EBH5200 eval board now recognizes the CF well
enough to boot to the login prompt. Before it would say it never
became ready. My CN3010-EVB-HS5 still boots properly. My older
CN3860-based board won't load the 64-bit kernel, either before or
after the change, and I didn't chase that down.
be brought up in the order they are enumerated in the device tree (in
particular, that thread 0 on each core be brought up first). The SLIST
through which we loop to start the CPUs has all of its entries added with
SLIST_INSERT_HEAD(), which means it is in reverse order of enumeration
and so AP startup would always fail in such situations (causing a machine
check or RTAS failure). Fix this by changing the SLIST into an STAILQ,
and inserting new CPUs at the end.
Reviewed by: jhb
Fix arguments passing to _long() version of atomic function for mips.
The native implementation is bogus in that regard and offers the same
problem solved for powerpc as r222198, but mips' guys just wanted a
small and self-contained patch for mips rather than rewriting the
whole support.
Reviewed by: art, imp
Tested by: gonzo
MFC after: 2 weeks
architectures (i386, for example) the virtual memory space may be
constrained enough that 2MB is a large chunk. Use 64K for arches
other than amd64 and ia64, with special handling for sparc64 due to
differing hardware.
Also commit the comment changes to kmem_init_zero_region() that I
missed due to not saving the file. (Darn the unfamiliar development
environment).
Arch maintainers, please feel free to adjust ZERO_REGION_SIZE as you
see fit.
Requested by: alc
MFC after: 1 week
MFC with: r221853
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
of endian-ness issues with the AR724x.
From Luiz:
* Fix the bus space tag used so endian-ness is correctly handled;
* Only do the workaround for the AR7240; AR7241/AR7242 (PB92)
don't require this
From me:
* Add a read flush from openwrt
Submitted by: Luiz Otavio O Souza
This is reported to work on the AR7240 based Ubiquiti Rocket M5
but I haven't tested it on that hardware. I also don't yet have
it fully working on the AR7242 based development board here;
probe/attach functions but the register space resource looks like
the endian-ness is wrong (0x10000000 instead of 0x00001000).o
Further digging will be required.
Submitted by: Luiz Otavio O Souza
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
* enable 11n
* add ath_ahb so the AHB<->ath glue is linked in
* disable descriptor order swapping, it isn't needed here
* disable interrupt mitigation, it isn't supported here
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
levels. TX would hang, RX wouldn't. A bit of digging showed the interface
send queue was full, but IFF_DRV_OACTIVE was clear and the hardware TX
queue was empty.
It turns out that there wasn't a check to drain the interface send
queue once hardware TX had completed, so if the interface send queue
had filled up in the meantime, subsequent packets would be dropped
by the higher layers and if_start (and thus arge_start()) would never
be called.
The fix is simple - call arge_start_locked() in the software interrupt
handler after the hardware TX queue has been handled or a TX underrun
occured. This way the interface send queue gets drained.
This is a MIPS4KC CPU with various embedded peripherals, including
wireless and ethernet support.
This commit includes the platform, UART, ethernet MAC and GPIO support.
The interrupt-driven GPIO code is disabled for now pending GPIO changes
from the submitter.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
offset in the flash.
Some devices (eg the TPLink WR-1043ND) don't have a flash environment
partition which can be queried for the current board settings.
This particular workaround allows for image creators to use a hint
to set the base MAC address. For example:
hint.arge.0.eeprommac=0x1f01fc00
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
just for Redboot.
At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.
Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.
A more "clean" solution will be needed at a later date.
The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.
Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>
configurations and make it opt-in for those who want it. LINT will
still build it.
While it may be a perfect win in some scenarios, it still troubles users
(see PRs) in general cases. In addition we are still allocating resources
even if disabled by sysctl and still leak arp/nd6 entries in case of
interface destruction.
Discussed with: qingli (2010-11-24, just never executed)
Discussed with: juli (OCTEON1)
PR: kern/148018, kern/155604, kern/144917, kern/146792
MFC after: 2 weeks
explicit process at fork trampoline path instead of eventhadler(schedtail)
invocation for each child process.
Remove eventhandler(schedtail) code and change linux ABI to use newly added
sysvec method.
While here replace explicit comparing of module sysentvec structure with the
newly created process sysentvec to detect the linux ABI.
Discussed with: kib
MFC after: 2 Week
- Use vm_paddr_t for pa in pmap_steal_memory()
- Use uintmax_t and %jx to ensure that physical address are printed
correctly in cpu_startup() and pmap_bootstrap()
a number of cores, this allows for a sparse set of CPUs. Implement support
for sparse core masks on Octeon.
XXX jeff@ suggests that all_cpus should include cores that are offline or
running other applications/OSes, so the platform API should be further
extended to allow us to set all_cpus to include all cores that are
physically-present as opposed to only those that are running FreeBSD.
Submitted by: Bhanu Prakash (with modifications)
Reviewed by: jchandra
Glanced at by: kib, jeff, jhb
o) Have mips_wblush just do syncw, not sync on Cavium Octeon.
o) Add support for reading and writing some Octeon-specific registers.
NB: Some of these are not entirely Octeon-specific.
Submitted by: Bhanu Prakash
should_yield(). Use this in various places. Encapsulate the common
case of check-and-yield into a new function maybe_yield().
Change several checks for a magic number of iterations to use
should_yield() instead.
MFC after: 1 week
- Provide trivial implementation of sf_buf_alloc(), sf_buf_free(),
sf_buf_kva() and sf_buf_page() using direct map for n64.
- uio_machdep.c - use macros so that the direct map will be used in
case of n64.
Reviewed by: imp (earlier version)
Obtained from: jmallett (user/jmallett/octeon)
- Remove sys/conf/ldscript.mips.64 and sys/conf/ldscript.mips.n32 and use
ldscript.mips for all ABIs. The default OUTPUT_FORMAT of the toolchain
is correct.
- Remove LDSCRIPT_NAME entires from XLR n32 and n64 conf files.
- Remove TARGET_BIG_ENDIAN from XLR conf files.
- Fix machine entry in XLRN32
sf buf allocation, use wakeup() instead of wakeup_one() to notify sf
buffer waiters about free buffer.
sf_buf_alloc() calls msleep(PCATCH) when SFB_CATCH flag was given,
and for simultaneous wakeup and signal delivery, msleep() returns
EINTR/ERESTART despite the thread was selected for wakeup_one(). As
result, we loose a wakeup, and some other waiter will not be woken up.
Reported and tested by: az
Reviewed by: alc, jhb
MFC after: 1 week
Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
In n32 and n64, add support for physical address above 4GB by having
64 bit page table entries and physical addresses. Major changes are:
- param.h: update PTE sizes, masks and shift values to support 64 bit PTEs.
- param.h: remove DELAY(), mips_btop(same as atop), mips_ptob (same as
ptoa), and reformat.
- param.h: remove casting to unsigned long in trunc_page and round_page
since this will be used on physical addresses.
- _types.h: have 64 bit __vm_paddr_t for n32.
- pte.h: update TLB LO0/1 access macros to support 64 bit PTE
- pte.h: assembly macros for PTE operations.
- proc.h: md_upte is now 64 bit for n32 and n64.
- exception.S and swtch.S: use the new PTE macros for PTE operations.
- cpufunc.h: TLB_LO0/1 registers are 64bit for n32 and n64.
- xlr_machdep.c: Add memory segments above 4GB to phys_avail[] as they are
supported now.
Reviewed by: jmallett (earlier version)
1. Use vm_paddr_t for physical addresses.
There are a few places in the MIPS platform code where vm_offset_t is
used for physical addresses, change these to use vm_paddr_t:
- phys_avail[], physmem_desc[] arrays
- pmap_mapdev(), page_is_managed(), is_cacheable_mem() pmap_map() args
- local variables of various pmap functions
2. Change init_pte_prot() return from int to pt_entry_t, as this can be
64 bit when using 64 bit TLB entries.
3. Update printing of pt_entry_t and of vm_paddr_t to use 'j' format with
uintmax_t. This will be useful later if we plan to use 64bit phsical addr
on 32 bit n32 compilation.
Reviewed by: imp
the ones which run the message ring handler.
Some bits of the interrupt mask are part of the status register which is
saved with the process context, and these bits are initialized from the
cpu on which the process is created. This means that all the processes
should have the same value for these interrupt mask bits, so that the
interrupt mask remains the same regardless of what thread is scheduled
on the cpu.
Submitted by: Sriram Gorti (srgorti at netlogicmicro dot com)
o) Clear/acknowledge receive interrupt at end of thread. This gives the
management interfaces performance on the order of 100Mbps rather than
the previous level of 10Mbps on my MR-730.
o) Add 'octm', a trivial driver for the 10/100 management ports found on some
Octeon systems.
o) Make the Simple Executive's management port helper routines compile on
FreeBSD (namely by not doing math on void pointers.)
o) Add a cvmx_mgmt_port_sendm routine to the Simple Executive to send an mbuf
so there is only one copy in the transmit path, rather than having to first
copy the mbuf to an intermediate buffer and then copy that to the Simple
Executive's transmit ring.
o) Properly work out MII addresses of management ports on the Lanner MR-730.
XXX The MR-730 also needs some patches to the MII read/write routines, but
this is sufficient for now. Media detection will be fixed in the future
when I can spend more time reading the vendor-supplied patches.
quite awful, because e.g. 4 packets will come in and get processed on 4
different cores at the same time, really battling with the TCP stack quite
painfully. For now, just run one task at a time.
This gets performance up in most cases to where it was before the correctness
fixes that got interrupts to run on all cores (except in high-load TCP transmit
cases where all we're handling receive for is ACKs) and in some cases it's
better now. What would be ideal would be to use a more advanced interrupt
mitigation strategy and possibly to use different workqueue groups per port for
multi-port systems, and so on, but this is a fine stopgap.
and pointers don't always have the same size, e.g. the __mips_n32 ABI
(ILP32) has 64 bit registers but 32 bit pointers.
On mips introduce PRIptr to fix the format specifier for (u)intptr_t.
Prefix PRI64 and PRIptr with underscores because macro names starting with
PRI[a-zX] are reserved for future use.
Approved by: kib (mentor)
architecture macros (__mips_n64, __powerpc64__) when 64 bit types (and
corresponding macros) are different from 32 bit. [1]
Correct the type of INT64_MIN, INT64_MAX and UINT64_MAX.
Define (U)INTMAX_C as an alias for (U)INT64_C matching the type definition
for (u)intmax_t. Do this on all architectures for consistency.
Suggested by: bde [1]
Approved by: kib (mentor)
of (unsigned) int __attribute__((__mode__(__DI__))). This aligns better
with macros such as (U)INT64_C, (U)INT64_MAX, etc. which assume (u)int64_t
has type (unsigned) long long.
The mode attribute was used because long long wasn't standardised until
C99. Nowadays compilers should support long long and use of the mode
attribute is discouraged according to GCC Internals documentation.
The type definition has to be marked with __extension__ to support
compilation with "-std=c89 -pedantic".
Discussed with: bde
Approved by: kib (mentor)
On some architectures UCHAR_MAX and USHRT_MAX had type unsigned int.
However, lacking integer suffixes for types smaller than int, their type
should correspond to that of an object of type unsigned char (or short)
when used in an expression with objects of type int. In that case unsigned
char (short) are promoted to int (i.e. signed) so the type of UCHAR_MAX and
USHRT_MAX should also be int.
Where MIN/MAX constants implicitly have the correct type the suffix has
been removed.
While here, correct some comments.
Reviewed by: bde
Approved by: kib (mentor)
It was used mainly to discover and fix some 64-bit portability problems
before 64-bit arches were widely available.
Discussed with: bde
Approved by: kib (mentor)
The macros here for generating coprocessor 0 accessors are named like:
MIPS_RDRW32_COP0
That macro would produce mips_rd_<register>() and mips_wr_<register>()
inlines to access the specified register by name from C. The problem is that
the R and the W were swapped in the macros originally; it was meant to be named
RDWR because it generated mips_rd_* and mips_wr_* functions, but was instead
spelled RDRW, which nobody should be expected to get right by anything other
than copy and paste.
It's too many consonants in a row to keep straight anyway, so just prefer e.g.:
MIPS_RW32_COP0
While here, add a missing #undef.
running an o32 kernel safely, and would have to add interrupt disabling and
reenabling to a bunch of macros in the Simple Executive sources to support it.
The only reason one would run an o32 kernel on Octeon would be to run o32 world,
which is better worked towards by adding o32 binary compatibility to n64 kernels
along with, eventually, supporting multilib systems so o32 binaries can run
alongside n32 and n64 ones.
Discussed with: imp
o) Make the octeon_wdog driver work on multi-CPU systems and to also print more
information on NMI that may aid debugging. Simplify and clean up internal
API and structure.
o) There's no good reason to make the low bits of the ebase the core
number. While per-CPU exception bases would be nice, for now we just
need to make ebase the same on all cores.
not just that it is greater than the minimal kernel virtual address, but also
that it is less than the maximal kernel virtual address. On n64 kernels, the
pcpup comes out of a direct-mapped address that, with an unsigned compare, is
rather greater than the minimal kernel virtual address.
o) Turn the panic if interrupts are disabled in cpu_idle into a KASSERT since on
other architectures it's behind INVARIANTS anyway.
o) Add a check that not all interrupts are masked, too.
o) Add cpu_idleclock() and cpu_activeclock() use to cpu_idle as is done on other
architectures.
2MB of memory in the bootmem allocator for the SDK to use internally at a later
point. It'd be nice if there were some functions we could call before
allocating memory to let various facilities reserve some memory, but for now
this seems sufficient. Previously some unfortunate systems could give up all
(or at least most) of their memory to the kernel from bootmem, and then
allocating command queues for packet output and the like would fail later in
the boot process (which in turn would lead to crashes even later.)
Reported by: kan
- Remove the -shared flag for the trampoline binary, generate an
ELF executable instead of a shared object.
- No need to generate tmphack.S, move the code to sys/mips/mips/inckern.S
- No need generate opt_kernname.h, KERNNAME can be passed with -D
Reviewed by: gonzo, imp
- ds1374u : use multi-byte write.
- at24co2n, max6657: remove mutex, iicbus has the necessary locking.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
1) 32-bit assignment are expected to always be atomic.
2) Release/acquire memory barrier semantics doesn't seem to be needed here.
So a simple assignment can be used.
Remove unused port_set_counter() while here, it also used to mis-use
atomic_set_int().
Reported by: jhb
Pointyhat to: avg
MFC after: 3 weeks
- Major update to xlr_i2c.c: do multi-byte ops correctly, remove unnecessary
code, add mutex to protect bus operations, style(9) fixes.
- Drivers for I2C devices on XLR/XLS engineering boards, ds1374u RTC, max6657
temparature sensor and at24co2n EEPROM.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
- remove unused code in mips/rmi/xlr_pci.c
- remove unused variable in mips/rmi/dev/nlge/if_nlge.c
- fix reference to old function in mips/mips/pmap.c
Reported by: Prabhath Raman (prabhath at netlogicmicro com)
Implement uma_small_alloc() and uma_small_free() for mips that allocates
pages from direct mapped memory. Uses the same mechanism as the page table
page allocator, so that we allocate from KSEG0 in 32 bit, and from XKPHYS
on 64 bit.
Reviewed by: alc, jmallett
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
link state polling or media-specific ones, while avoidiing changing link state
on interfaces that use miibus; this substantially speeds up link time on
interface (re)initialization.
list on exit from the transmit path. The scatter-gather list itself can be
asynchronously DMAed to the transmit hardware, and we could actually lock up
the transmitter if any of a number of races around this were lost.
Instead, let the PKO free the scatter-gather list when it is done with it, and
use the "i" bit in each segment of the packet to avoid having them go into the
FPA.
This fixes an unrecoverable transmit stall under transmit load.
MFC after: 3 days
facilities as well as support for the Octeon 2 family of SoCs.
XXX Note that with our antediluvian assembler, we can't support some Octeon 2
instructions and fall back to using the old ones instead.
o) Remove some options that are configurable on Linux but not FreeBSD.
o) Centralize open/poll/stop routines for XAUI and SGMII and use the common
uninit routine directly rather than providing a wrapper for it. The init
functions for these interfaces are now identical and the common init routine
could merge in setting those function pointers except that some hardware
seems to use no open/poll/stop method?
The current implementation of vm_page_alloc_freelist() does not handle
order > 0 correctly. Remove order parameter to the function and use it
only for order 0 pages.
Submitted by: alc
DPCPU_DEFINE and VNET_DEFINE macros, as these cause problems for various
people working on the affected files. A better long-term solution is
still being considered. This reversal may give some modules empty
set_pcpu or set_vnet sections, but these are harmless.
Changes reverted:
------------------------------------------------------------------------
r215318 | dim | 2010-11-14 21:40:55 +0100 (Sun, 14 Nov 2010) | 4 lines
Instead of unconditionally emitting .globl's for the __start_set_xxx and
__stop_set_xxx symbols, only emit them when the set_vnet or set_pcpu
sections are actually defined.
------------------------------------------------------------------------
r215317 | dim | 2010-11-14 21:38:11 +0100 (Sun, 14 Nov 2010) | 3 lines
Apply the STATIC_VNET_DEFINE and STATIC_DPCPU_DEFINE macros throughout
the tree.
------------------------------------------------------------------------
r215316 | dim | 2010-11-14 21:23:02 +0100 (Sun, 14 Nov 2010) | 2 lines
Add macros to define static instances of VNET_DEFINE and DPCPU_DEFINE.
mipsel' or 'machine mips mipseb' into the config file (with a few 64's
tossed in for good measure). This will let us build the proper
kernels with different worlds as part of make universe.
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
using miibus, since for some devices that use multiple addresses on the bus,
going through miibus may be unclear, and for devices that are not standard
MII PHYs, miibus may throw a fit, necessitating complicated interfaces to
fake the interface that it expects during probe/attach.
o) Make the mv88e61xx SMI interface in octe attach a PHY directly and fix some
mistakes in the code that resulted from trying too hard to present a nice
interface to miibus.
o) Add a PHY driver for the mv88e61xx. If attached (it is optional in kernel
compiles so the default behavior of having a dumb switch is preserved) it
will place the switch in a VLAN-tagging mode such that each physical port
has a VLAN associated with it and interfaces for the VLANs can be created to
address or bridge between them.
XXX It would be nice for this to be part of a single module including the
SMI interface, and for it to fit into a generic switch configuration
framework and for it to use DSA rather than VLANs, but this is a start
and gives some sense of the parameters of such frameworks that are not
currently present in FreeBSD. In lieu of a switch configuration
interface, per-port media status and VLAN settings are in a sysctl tree.
XXX There may be some minor nits remaining in the handling of broadcast,
multicast and unknown destination traffic. It would also be nice to go
through and replace the few remaining magic numbers with macros at some
point in the future.
XXX This has only been tested with the MV88E6161, but it should work with
minimal or no modification on related switches, so support for probing
them was included.
Thanks to Pat Saavedra of TELoIP and Rafal Jaworowski of Semihalf for their
assistance in understanding the switch chipset.
physical address. Adds a dma tag to the XLR/XLS pci bus with the
lowaddr if the CPU happens to be a XLR C rev.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro dot com))
- nlge_ioctl handles IFF_UP and IFF_PROMISC flags
- Translate table code, to enable flow based CPU assignment added
disabled by default (can be enabled by a tunable).
- Changed signature of nlge_port_disable to make it consistent with nlge_port_enable
- Removed TXCSUM and VLAN_HW_TAGGING from i/f capabilities.
Submitted by: Sriram Gorti (srgorti at netlogicmicro dot com)
sysctl and counters for message ring threads (intial version). Update
watermark values, and and decrease the maximum threads to 3 (this will leave
a few CPUs for other processes)
Minor comment fix in nlge.
- Wakeup multiple threads per core using message ring watermark interrupts.
- Update message ring handler registration, use the real device station id
for registering interrupts.
- rge/nlge: update for the new message ring registration code.
- rge/nlge: use 2 message ring stations for incoming packets, this will
allow more messages to be queued.
- nlge: comment fixes, remove unused variable
- style and whitespace fixes
the miibus attached to octe interfaces.
o) Add an SMI/MDIO interface to the MV88E61XX and use it for the switch PHY on
the Lanner MR-320. An actual driver for the switch PHY will come later.
Note that for now it intercepts and fakes MII_BMSR reads to prevent the
miibus from talking to anything but the switch itself.
bus interface does that's special here now is to use a 64-bit register size.
In theory, uart(4) ought to support a regsz as well as regshft and support
64-bit registers directly.
Also use the UART class's range rather than a hand-coded 1024 for the address
range.
o) Give a virtual address for I/O ports on n64.
o) On the Portwell CAM-0100, return the right IRQ for the on-board SATA.
o) Except on bridges, only set PORTEN and MEMEN on devices that have I/O or
memory BARs respectively.
o) Disable PORTEN and MEMEN while reprogramming BARs.
o) On the Lanner MR-955, set the Tx DMA power register for the on-board Promise
SATA controller.
- XLS B0 and later revision chips have PCIe link 2 & 3 mapped to different
PIC interrupts. Update pic.h, board.h and xlr_pci.c to reflect this.
- remove debug prints in xlr_pci.c
- add more processor IDs to board.h, add function xlr_is_xls_b0()
- some style(9) and whitespace fixes
these could be made dependent on either of the octusb or octe options, but
making them standard fixes a number of option combinations that were previously
broken.
driver to try to switch interrupt handlers at setup. It's not a very
good implementation of bus_teardown_intr, though.
o) Set cache line size and latency timers for PCI devices per Linux.
o) Reset and configure the bus from scratch rather than expecting U-Boot to
do it for us. Values and configuration from Linux, U-Boot and comments
in the Cavium Simple Executive sources.
o) Do a resource assignment and bus numbering pass in the absence of a PCI
BIOS or firmware that will do it for us.
XXX This has to be the third or fourth instance of this in FreeBSD and
it would be nice to have it become part of the PCI bus driver itself,
like it is on Linux.
o) Fix interrupt mapping for and adjust bus configuration for the Lanner
MR-955, based on information provided by Lanner.
- 64 bit fixes for ifnlge.c
- Use m_nextpkt to save mbuf vaddr on 64 bit, we cannot store the
64 bit vaddr in the 40bit freeback field.
- remove unused code and unnecessary variables.
- use xlr_io_mmio macro instead of adding io base address
- rewrite GPIO related code to fixup nlge using xlr_write_reg and DELAY
- support for engg boards major num 11 and 12
- add xlr_paddr_lw() to load 32bit value from physical address, fix
inline assembly
- style fixes
- Process some tx done messages in the transmit path, to ensure that
the XLR NA tx done FIFO does not overflow.
- Add a message ring handler API to process atmost a given number of
messages from a specified bucket mask. This will be used to process
the tx done messages
- Add a callout to restart transmit in the case transmit gets blocked.
- Update enable_msgring_int() and disable_msgring_int(), remove unused
args and make static.
Obtained from: Sriram Gorti (srgorti at netlogicmicro dot com)
- Compile fixes for 9.0, the previous version of this driver was
for FreeBSD 6.
- Add virtual address field in OperationDescriptor_t, we cannot use
MIPS_PHYS_TO_KSEG0 on physical address.
- Fixes for new message ring API
- Remove unused sys/mips/rmi/dev/sec/stats.h
- Whitespace fixes
- Move RMI MIPS extension to atomic increment word (LDADDWU) to common
header file sys/mips/rmi/rmi_mips_exts.h
- Fix xlr_ldaddwu() for 64 bit, it is a 32 bit operation, use
unsigned int* instead of unsigned long* argument
- Provide dummy xlr_enable_kx/xlr_restore_kx for n32 and n64.
- Provide xlr_paddr_ld() instead of xlr_paddr_lw(), so that the
descriptor formats are same for 32 and 64 bit
- update nlge and rge for the changes
These changes are also needed by the security driver which will be
added later.
Do not explicitly enable interrupts in smp_init_secondary() because it
renders any spinlock protected code after that point to run with
interrupts enabled. This is because the processor is executing in the
context of idlethread whose 'md_spinlock_count' is already set to 1.
Instead just let sched_throw() re-enable interrupts when it releases
the spinlock.
The original powerpc commit log for r212559 is available here:
http://svn.freebsd.org/viewvc/base?view=revision&revision=212559
- Remove sync from msgrng_send, sync needs to be called just once before
sending.
- Fix retry logic - don't reload registers when retrying in message_send,
also fix check for send pending fail.
- remove unused message_send_block_fast()
- merge message_receive_fast() to message_receive
- style(9) fixes, and comments
- rge and nlge updated for the sys/mips/rmi/msgring.h changes
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
- Provide 64 bit implementations for some macros. On n64 and n32,
don't split 64 bit values.
- No need for 32 bit ops for control registers.
- Fix few bugs (write control reg, write_c0_register64).
- Re-write EIRR/EIMR/CPUID operations using read_c0_registerXX, no
need of inline assembly.
- rename control reg access functions to avoid phnx, update callers.
- stlye/whitespace fixes.
- Updates for the message ring clean up in r212321.
- Instead of dropping Tx packet on credit fail, retry send until it
succeeds.
- Fix freeing mbufs in case of P2P descriptors:
We cannot free the mbuf when the P2P descriptor freeback is received. The
mbuf may be still in use by the GMAC, since the P2P freeback indicates that
it read the P2D descriptors in the P2P message.
Now we free just the P2P descriptor when the P2P freeback message is
received. Another freeback P2D message has been added to the end of
the packet descriptors, the mbuf will be freed only when we received
this.
The P2P descriptor issue was reported by srgorti at netlogicmicro dot com.
Fix message ring send path:
- define msgrng_access_enable() which disables local interrupts
and enables message ring access. Also define msgrng_restore() which
restores interrupts
- remove all other msgrng enable/disable macros, no need of critical_enter
and other locking here.
- message_send() fixup: re-read status until pending bit clears
- message_send_retry() fixup: retry only few times with interrupts disabled
- Fix up message_send/message_send_retry callers - call
msgrng_access_enable() and msgrng_restore() correctly so that interrupts
are not disabled for long.
- removed unused and obsolete code from sys/mips/rmi/msgring.h
- some style fixes - more later
rge.c (XLR GMAC driver):
- updated for the message ring changes
- remove unused message_send_block()
- retry on credit failure, this is not a permanent failure when credits
are configured correctly. Add panic if credits are not available to
send for a long time.
Fix interrupt routing so that the irq returned is correct for XLR and
XLS. This also updates the MSI hack we had earlier - we still don't
really support MSI, but we support some drivers that use MSI, by providing
support for allocating one MSI per pci link - this MSI is directly
mapped to the link IRQ.
- set cache_coherent_dma flag in cpuinfo for XLR, this will make sure that
BUS_DMA_COHERENT flag is handled correctly in busdma_machdep.c
- iodi.c, call device_get_name() just once
- clear RMI specific EIRR while intializing CPUs
- remove debug print in intr_machdep.c
unused files.
- remove clock.c and clock.h, these are not used after the new timer
code was added.
- remove duplicated include files, fix header file ordering, remove
some unneeded includes.
- rename mips/rmi/shared_structs.h which contains the RMI boot loader
interface to mips/rmi/rmi_boot_info.h. Remove unused files
mips/rmi/shared_structs_func.h and sys/mips/rmi/shared_structs_offsets.h
- merge mips/rmi/xlrconfig.h and mips/rmi/rmi_mips_exts.h, and remove
duplicated functions.
- nlge - minor change to remove unneeded argument.
- Add FreeBSD svn keyword for headers
PMAP_DIAGNOSTIC was eliminated from amd64/i386, and, in fact, the
non-MIPS parts of the kernel, several years ago. Any of the interesting
checks were turned into KASSERT()s. Basically, the motivation was that
lots of people run with INVARIANTS but no one runs with DIAGNOSTIC.
panic strings needn't and shouldn't have a terminating newline.
Finally, there is one functional change. The sched_pin() in
pmap_remove_pages() is an artifact of the way we temporarily map page
table pages on i386. (The mappings are processor private. We don't do
a system-wide shootdown.) It isn't needed by MIPS.
Tested by: jchandra
Submitted by: alc
and XAUI 10G interfaces in addition RGMII/SGMII 1G interfaces. This driver
is work in progress.
board.c and board.h expanded to include more info.
Only one of rge and nlge can be enabled at a time, rge will be deprecated
when nlge stabilizes.
Submitted by: Sriram Gorti <srgorti at netlogicmicro com>
SMP.
We used to route all PIC based interrupts to cpu 0, and used the per-CPU
interrupt mask to enable/disable interrupts. But the interrupt threads can
run on any cpu on SMP, and the interrupt thread will re-enable the interrupts
on the CPU it runs on when it is done, and not on cpu0 where the PIC will
still send interrupts to.
The fix is move the disable/enable for PIC based interrupts to PIC, we will
ack on PIC only when the interrupt thread is done, and we do not use the
per-CPU interrupt mask.
The changes also introduce a way for subsystems to add a function that
will be called to clear the interrupt on the subsystem. Currently This is
used by the PCI/PCIe for doing additional work during the interrupt
handling.
- Use timer 7 in XLR PIC as a 32 counter
- provide pic_init_timer(), pic_set_timer(), pic_timer_count32() and
pic_timer_count() PIC timer operations.
- register this timer as platform_timecounter on rmi platform.
- style(9) fixes to mips/rmi platform files
- update pic.h to add pic_setup_intr() and use pic_setup_intr() for setting
up interrupts which are routed thru PIC.
- remove rmi_spin_mutex_safe and haslock, and make sure that the functions
are called only after mutexes are available.
- move PIC code to xlr_machdep.c
- move fast message ring code completely to on_chip.c
- move memory initialization to a new function xlr_mem_init()
- style fixes
* Add a function to write to the relevant PLL register
* Break out the PLL configuration for the AR71XX into the CPU ops,
lifted from if_arge.c.
* Add the AR91XX PLL configuration ops, using the AR91XX register
definitions.