The AltiVec header file is defining "vector", except in C++ build.
The keyword "vector" may conflict easily.
As a rule, it is better to use the alternative keyword "__vector",
so we will be able to #undef vector after including AltiVec header.
Later it may become possible to #undef vector in rte_altivec.h
with a compatibility breakage.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: David Christensen <drc@linux.vnet.ibm.com>
The lpm_process_event_pkt() can either process a packet using an
architecture specific (defined for X86/SSE, ARM/Neon and PPC64/Altivec)
path or a scalar one. The choice is however done using an ifdef
pre-processor macro. Because of that the scalar version was apparently
not widely exercised/compiled.
Due to some copy/paste errors, the scalar logic in
lpm_process_event_pkt() retained a "continue" statement where it should
utilize rfc1812_process() and return the port/BAD_PORT.
Fixes: 99fc91d180 ("examples/l3fwd: add event lpm main loop")
Signed-off-by: Stanislaw Kardach <kda@semihalf.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Quiesce event ports used by the workers core on exit to free up
any outstanding resources.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Event ports are configured to implicitly release the scheduler contexts
currently held in the next call to rte_event_dequeue_burst().
A worker core might still hold a scheduling context during exit as the
next call to rte_event_dequeue_burst() is never made.
This might lead to deadlock based on the worker exit timing and when
there are very less number of flows.
Add a cleanup function to release any scheduling contexts held by the
worker by using RTE_EVENT_OP_RELEASE.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Event ports are configured to implicitly release the scheduler contexts
currently held in the next call to rte_event_dequeue_burst().
A worker core might still hold a scheduling context during exit, as the
next call to rte_event_dequeue_burst() is never made.
This might lead to deadlock based on the worker exit timing and when
there are very less number of flows.
Add clean up function to release any scheduling contexts held by the
worker by using RTE_EVENT_OP_RELEASE.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Event ports are configured to implicitly release the scheduler contexts
currently held in the next call to rte_event_dequeue_burst().
A worker core might still hold a scheduling context during exit, as the
next call to rte_event_dequeue_burst() is never made.
This might lead to deadlock based on the worker exit timing and when
there are very less number of flows.
Add clean up function to release any scheduling contexts held by the
worker by using RTE_EVENT_OP_RELEASE.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Event ports are configured to implicitly release the scheduler contexts
currently held in the next call to rte_event_dequeue_burst().
A worker core might still hold a scheduling context during exit, as the
next call to rte_event_dequeue_burst() is never made.
This might lead to deadlock based on the worker exit timing and when
there are very less number of flows.
Add clean up function to release any scheduling contexts held by the
worker by using RTE_EVENT_OP_RELEASE.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Move message handler description and callbacks into a single array and
remove unneeded VHOST_USER_MAX and VHOST_SLAVE_MAX enums.
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
In async data path, call rte_vhost_async_get_inflight_thread_unsafe()
API to directly return the number of in-flight packets instead of
maintaining a local variable.
Signed-off-by: Xuan Ding <xuan.ding@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
TIMER_MILLISECOND is defined as the number of cpu cycles per millisecond,
current definition is correct for cores with frequency of 2GHZ, for cores
with different frequency, it caused different periods between refresh,
(i.e. the definition is about 14ms on ARM cores).
The devarg that stated the period between stats print was not used,
instead, it was always defaulted to 10 seconds (on 2GHZ core).
Use DPDK API to get CPU frequency, to define TIMER_MILLISECOND.
Use the refresh period devarg instead of defaulting to 10s always.
Fixes: 387259bd6c ("examples/l2fwd-crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Raja Zidane <rzidane@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
The conditional rte_spinlock_trylock() was used as if it is an
unconditional lock operation in a number of places.
Fixes: cc7e8ae84f ("examples/bond: add example application for link bonding mode 6")
Cc: stable@dpdk.org
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
This patch fixes the stack buffer overflow error reported
from AddressSanitizer.
Function send_packetsx4() tries to access out of bound data
from rte_mbuf and fill it into TX buffer even in the case
where no pending packets (len = 0).
Performance impact:- No
ASAN error report:-
==819==ERROR: AddressSanitizer: stack-buffer-overflow on address
0xffffe2c0dcf0 at pc 0x0000005e791c bp 0xffffe2c0d7e0 sp 0xffffe2c0d800
READ of size 8 at 0xffffe2c0dcf0 thread T0
#0 0x5e7918 in send_packetsx4 ../examples/l3fwd/l3fwd_common.h:251
#1 0x5e7918 in send_packets_multi ../examples/l3fwd/l3fwd_neon.h:226
Fixes: 96ff445371 ("examples/l3fwd: reorganise and optimize LPM code path")
Cc: stable@dpdk.org
Signed-off-by: Rahul Bhansali <rbhansali@marvell.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add CR character at print link state information.
Fixes: db4e81351f ("examples: use new link status print format")
Cc: stable@dpdk.org
Signed-off-by: Tianli Lai <laitianli@tom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The default values of rx mq_mode and rx offloads for port
will cause symmetric_mp startup failure if the port do not
support rss or csum. This patch makes the app to reconfigure
the NIC without them. Only quit the app if the second
reconfiguration fails.
Signed-off-by: Wenwu Ma <wenwux.ma@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Wei Ling <weix.ling@intel.com>
Distributor application creates one Tx queue per core. However
the transmit is done only from a single core. Hence creating
one Tx queue is enough.
Fixes: 07db4a9750 ("examples/distributor: new sample app")
Cc: stable@dpdk.org
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Make Rx and Tx queue sizes configurable from the command line.
This helps DTS write better test cases.
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Kathleen Capella <kathleen.capella@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
nb_rxd and nb_txd are used in polling mode and event mode of
operation. nb_rxd and nb_txd are already global in polling mode
but are not visible to event mode code. Make them visible to all
parts of the application.
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Kathleen Capella <kathleen.capella@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Yingya Han < yingyax.han@intel.com>
Add support to define ipv4 and ipv6 forwarding tables
from reading from a config file for EM with a format
similar to l3fwd-acl one.
Users can now use the default hardcoded route tables
or optionally config files for 'l3fwd_em'. Default
config files have been provided for use with EM.
Related l3fwd docs have been updated to reflect these
changes.
Signed-off-by: Sean Morrissey <sean.morrissey@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add support to define ipv4 and ipv6 forwarding tables
from reading from a config file for LPM and FIB,
with format similar to l3fwd-acl one.
Users can now use the default hardcoded route tables
or optionally config files. Default config files have
been provided for use with LPM and FIB.
Signed-off-by: Sean Morrissey <sean.morrissey@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Tested-by: Yingya Han <yingyax.han@intel.com>
dpdk-vhost will fail to launch with a 40G i40e port because
there are not enough mbufs. This patch adds a new option
--total-num-mbufs, through which the user can set larger
mbuf pool to avoid this problem.
Fixes: 4796ad63ba ("examples/vhost: import userspace vhost application")
Cc: stable@dpdk.org
Signed-off-by: Wenwu Ma <wenwux.ma@intel.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
The dma-type parameter was not supported when dmadev was
integrated in vhost, but the help info still exists. This
patch deletes it.
Fixes: 53d3f4778c ("vhost: integrate dmadev in asynchronous data-path")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Coverity flags an issue with 32-bit value. If max ethports value is
configured with a value larger than 32 there will be an issue.
Coverity issue: 375863 Unintentional integer overflow
Fixes: 387259bd6c ("examples/l2fwd-crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Brian Dooley <brian.dooley@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Add support to enable per port packet pool and also override
vector pool size from command line args. This is useful
on some HW to tune performance based on usecase.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Fix packet processing to skip after mbuf is freed instead of
touching and Tx'ing it.
Also free vector event buffer in event worker when after processing
there is no pkt to be enqueued to Tx adapter.
Fixes: 86738ebe1e ("examples/ipsec-secgw: support event vector")
Cc: stable@dpdk.org
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Update error prints in data path to RTE_LOG_DP().
Error prints in fast path are not good for performance
as they slow down the application when few bad packets are
received.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Usage of unprotected port mask without any configured SA inbound, will
cause use of uninitialized SA context, so disallow such configuration.
Signed-off-by: Volodymyr Fialko <vfialko@marvell.com>
Acked-by: Anoob Joseph <anoobj@marvell.com>
Masking of core mask was incorrect. Instead of using 1U for shifting, it
should be using 1LU as the result is assigned to uint64.
CID 375859: Potentially overflowing expression "1U << app_main_core" with
type "unsigned int" (32 bits, unsigned) is evaluated using 32-bit
arithmetic, and then used in a context that expects an expression of
type "uint64_t" (64 bits, unsigned).
Coverity issue: 375859
Fixes: de3cfa2c98 ("sched: initial import")
Cc: stable@dpdk.org
Signed-off-by: Megha Ajmera <megha.ajmera@intel.com>
Acked-by: Morten Brørup <mb@smartsharesystems.com>
Removed RTE_SCHED_SUBPORT_TC_OV from rte_config.h.
Best effort traffic class oversubscription is always enabled.
Signed-off-by: Megha Ajmera <megha.ajmera@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Add support for the show CLI command to print table entries to a file
instead of standard output.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Harshad Narayane <harshad.suresh.narayane@intel.com>
An additional output port is now implicitly created for every pipeline
to serve as the packet drop port. Up to now, the drop port had to be
explicitly created for each pipeline.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Yogesh Jangra <yogesh.jangra@intel.com>
Move the table type registration for the well known table types from
the application to the pipeline library.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Yogesh Jangra <yogesh.jangra@intel.com>
Move the port type registration for the well known port types from the
application to the pipeline library.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Yogesh Jangra <yogesh.jangra@intel.com>
RTE_MBUF_F_TX_OUTER_IP_CKSUM should not be set for IPv6 packets.
Fixes: a7f32947a3 ("examples/ipsec-secgw: support TCP TSO")
Cc: stable@dpdk.org
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Since dmadev is introduced in 21.11, to avoid the overhead of vhost DMA
abstraction layer and simplify application logics, this patch integrates
dmadev in asynchronous data path.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Signed-off-by: Sunil Pai G <sunil.pai.g@intel.com>
Tested-by: Yvonne Yang <yvonnex.yang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Functions like free, rte_free, and rte_mempool_free
already handle NULL pointer so the checks here are not necessary.
Remove redundant NULL pointer checks before free functions
found by nullfree.cocci
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
While dequeuing the packets from the event device, burst size
is provided in the API. This was not getting properly
configured in the application. This patch correctly configures
the burst size.
Fixes: aaf58cb85b ("examples/l3fwd: add event port and queue setup")
Cc: stable@dpdk.org
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
Using RTE_MBUF_F_TX_TCP_SEG requires L4 length to be set.
Fixes: a7f32947a3 ("examples/ipsec-secgw: support TCP TSO")
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
The size of delay request message sent out by the DPDK
ptpclient application was observed to have extra length
than expected. Due to this, bad messages were observed
on the master side and delay response was not received.
This patch fixes this bug.
Fixes: ab129e9065 ("examples/ptpclient: add minimal PTP client")
Cc: stable@dpdk.org
Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
Acked-by: Nipun Gupta <nipun.gupta@nxp.com>
Wakeup happens quite often (several hundred times a second) in
l3fwd-power example app in PMD power management mode, so this
message is appearing too often to be useful.
This patch reverts that info message addition.
Fixes: 931e3a9945 ("examples/l3fwd-power: add wakeup log")
Signed-off-by: David Hunt <david.hunt@intel.com>
Tested-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Reshma Pattan <reshma.pattan@intel.com>
Multiple drivers are defining macros for VLAN header length, to remove
the redundancy defining macro in the ether header.
And updated drivers to use the new macro.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Jiawen Wu <jiawenwu@trustnetic.com>
Currently, ethtool directly ends the process after 'quit' cmd. In this
case, software resources are not released and hardware resources of the
device are not uninstalled.
This patch adds closing port operation to release resources.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In DPDK, 'rte_socket_id' means the running socket while
'rte_eth_dev_socket_id' is the device socket.
For better performance, memory which queue setup used and device
should be in the same socket.
This patch make sure it calls rte_eth_dev_socket_id API to get device
socket_id when setting ringparam.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
When the example starts in mergeable mode with an i40e port,
it fails to launch because the examples use default mtu MAX_MTU
to configure ethdev. The root cause is some devices have Ethernet
frame overhead and then MAX_MTU will be larger than device's max
mtu, so the ethdev configure will fail.
This patch checks the device's max MTU before setting the ethdev
configuration. If the device has a max MTU, use that value to
configure.
Fixes: 1bb4a528c4 ("ethdev: fix max Rx packet length")
Reported-by: Xingguang He <xingguang.he@intel.com>
Signed-off-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch adds a log in main telemetry loop to show the thread has
woken up and begun to send and receive packets.
Signed-off-by: Miao Li <miao.li@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
Update public macros to have RTE_IP_FRAG_ prefix.
Update DPDK components to use new names.
Keep obsolete macro for compatibility reasons.
Renamed experimental function ``rte_frag_table_del_expired_entries``to
``rte_ip_frag_table_del_expired_entries`` to comply with other public
API naming convention.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The 'IPv4' in the comment is to mark the code snippet, while it made
some confusion. Then removing 'IPv4' description will be clearer.
Fixes: 9a212dc06c ("doc: use code snippets in sample app guides")
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
MP servers distributes Rx packets between clients according to
round-robin scheme.
Current implementation always started packets distribution from
the first client. That procedure resulted in uniform distribution
in cases when Rx packets number was around clients number
multiplication. However, if RX burst repeatedly returned single
packet, round-robin scheme would not work because all packets
were assigned to the first client only.
The patch does not restart packets distribution from
the first client.
Packets distribution always continues to the next client.
Fixes: af75078fec ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Currently, EAL init cannot be interrupted with SIGINT because the
signal handler is already overridden by the time EAL init happens.
Fix it by moving signal handler installation to after EAL
initialization, to allow SIGNIT to interrupt EAL initialization.
Fixes: d7937e2e3d ("power: initial import")
Fixes: 613ce6691c ("examples/l3fwd-power: implement proper shutdown")
Cc: stable@dpdk.org
Signed-off-by: Harneet Singh <harneet.singh@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Reported by clang 13.
This patch removes the hits variable from the cpu_load_collector function
within the performance thread example app as it is an unused but set
variable.
Bugzilla ID: 881
Fixes: d48415e1fe ("examples/performance-thread: add l3fwd-thread app")
Cc: stable@dpdk.org
Reported-by: Liang Longfeng <longfengx.liang@intel.com>
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
The l3fwd example should use the reserved IPv4/v6 reserved address
ranges defined in RFC5735, RFC5180 and RFC863 discard protocol for
the port number in the exact match mode of L3 forwarding.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Since the number of Ethernet ports have gone up, print the device name
(which for PCI devices is the BDF triplet), along with the routes.
This is also helpful for cases where allow listing order is not honored.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Increase the number of routes from 8 to 16 that are statically added for
lpm and em mode as most of the SoCs support more than 8 interfaces.
The number of routes added is equal to the number of ethernet devices
ports enabled through port mask.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Trying to disable the vhost library, meson will complain it can't build
the vhost* and vdpa examples when passing -Dexamples=all.
-Dexamples=all skips examples if the example itself announces it can't
be built (for external dependencies, internal dependencies and other
reasons).
Since examples/meson.build will evaluate the internal dependencies
in any case, let's move the check there and resolve the issue for
optional internal libraries.
Fixes: 0bf5832222 ("lib: allow disabling optional libraries")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Add 1MB data-unit length to the capability's bitmap.
Handle 1MB data-unit length in the mlx5 session create operation,
and expose its capability in the mlx5 capabilities.
Signed-off-by: Raja Zidane <rzidane@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Adds event vector support to inline protocol offload mode.
By default vector support is disabled, it can be enabled by
using the option --event-vector.
Additional options to configure vector size and vector timeout are
also implemented and can be used by specifying --vector-size and
--vector-tmo.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Applications should not quietly ignore an ethdev reset event.
Register an event handler for ethdev reset callback
RTE_ETH_EVENT_INTR_RESET that prints a message and
quits the application.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
New option added to the SA configuration arguments that
allows setting an arbitrary start value for ESN.
For example in the SA below ESN will be enabled and first egress
IPsec packet will have the ESN value 10000:
sa out 15 cipher_algo null auth_algo null mode ipv4-tunnel \
src 172.16.1.5 dst 172.16.2.5 \
esn 10000
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Add telemetry support to the IPsec GW sample app and add
support for per SA telemetry when using IPsec library.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Enable UDP encapsulation for both transport and tunnel modes for the
inline crypto offload path.
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Rework create inline session function as to update the session
configuration parameters before create session is called.
Also updated the rss key array size to prevent buffers overflows
with PMDs that copy more than 40 bytes.
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
When STATS_INTERVAL is set to a non-zero value the
core_statistics array will be defined in multiple
compilation units and this can trigger a linker error
on particular environments. In order to fix this the
core_statistics definition was moved out of the header file.
Fixes: 1329602b6c ("examples/ipsec-secgw: add per-core packet statistics")
Cc: stable@dpdk.org
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Add support to allow user to specific MSS for TCP TSO offload on a per SA
basis. MSS configuration in the context of IPsec is only supported for
outbound SA's in the context of an inline IPsec Crypto offload.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
This patch fixes the missing device start for fips validation
sample app.
Bugzilla ID: 842
Fixes: 261bbff75e ("examples: use separate crypto session mempools")
Cc: stable@dpdk.org
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
As previously announced, this patch renames struct
vhost_device_ops to struct rte_vhost_device_ops.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Now that IO vectors iterator have been simplified, the
rte_vhost_async_desc struct only contains a pointer on
the iterator array stored in the async metadata.
This patch removes it, and pass directly the iterators
array pointer to the transfer_data callback. Doing that,
we avoid declaring the descriptor array in the stack, and
also avoid the cost of filling it.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Jiayu Hu <jiayu.hu@intel.com>
Offset and count fields are unused and so can be removed.
The offset field was actually in the Vhost example, but
in a way that does not make sense.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Jiayu Hu <jiayu.hu@intel.com>
This patch introduces rte_vhost_iovec struct that contains
both source and destination addresses since we always have
a 1:1 mapping between source and destination. While using
the standard iovec struct might have seemed better, having
to duplicate IO vectors and its iterators is memory
inefficient and make the implementation more complex.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Jiayu Hu <jiayu.hu@intel.com>
In l3fwd-power, there is default port configuration which requires
RSS and IPv4/UDP/TCP checksum. Once device does not support these,
the l3fwd-power will exit and report an error.
This patch updates the port configuration based on device capabilities
after getting the device information to support devices like virtio
and vhost.
Signed-off-by: Miao Li <miao.li@intel.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
Adding the PIE support for IP Pipeline
Signed-off-by: Wojciech Liguzinski <wojciechx.liguzinski@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
patch add support enable PIE or RED by
parsing config file.
Signed-off-by: Wojciech Liguzinski <wojciechx.liguzinski@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
Implement PIE based congestion management based on rfc8033.
The Proportional Integral Controller Enhanced (PIE) algorithm works
by proactively dropping packets randomly.
PIE is implemented as more advanced queue management is required to
address the bufferbloat problem and provide desirable quality of
service to users.
Tests for PIE code added to test application.
Added PIE related information to documentation.
Signed-off-by: Wojciech Liguzinski <wojciechx.liguzinski@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
This patch adds a new parameter to the FIB configuration to specify
the size of the extension for internal RIB structure.
Signed-off-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Tested-by: Conor Walsh <conor.walsh@intel.com>
Code changes to avoid the following build error:
"strncpy specified bound XX equals destination size".
Signed-off-by: Xueqin Lin <xueqin.lin@intel.com>
Signed-off-by: Zhihong Peng <zhihongx.peng@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Since the APIs have been updated from rawdev to dmadev, the application
should also be renamed to match. This patch also includes the documentation
updates for the renaming.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Existing functions, structures, defines etc need to be updated to reflect
the change to using the dmadev APIs.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
The dmadev library abstraction allows applications to use the same APIs for
all DMA device drivers in DPDK. This patch updates the ioatfwd application
to make use of the new dmadev APIs, in turn making it a generic application
which can be used with any of the DMA device drivers.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Enable dumping device info via the signal handler. With this change, when a
SIGUSR1 is issued, the application will print a dump of all devices being
used by the application.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Add a command line option to control the interval between stats prints.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Add command line option for setting the max frame size.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Add a commandline options to control the HW copy batch size in the
application.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
Few changes in ioat sample behaviour:
- Always do SW copy for packet metadata (mbuf fields)
- Always use same lcore for both DMA requests enqueue and dequeue
Main reasons for that:
a) it is safer, as idxd PMD doesn't support MT safe enqueue/dequeue (yet).
b) sort of more apples to apples comparison with sw copy.
c) from my testing things are faster that way.
Documentation updates to reflect these changes are also included.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Conor Walsh <conor.walsh@intel.com>
The default behaviour of l2fwd is to exit if we are unable to turn
promiscuous mode on. On some aws instances turning promiscuous mode
on is not permitted. In such cases there should be a way to run the
application without promiscuous mode.
This patch allows user to turn promiscuous mode on via command line
parameter. l3fwd has a similar option available.
Signed-off-by: Sarosh Arif <sarosh.arif@emumba.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
FINISHED state seems to be used to indicate that the worker's update
of the 'state' is not visible to other threads. There seems to be no
requirement to have such a state.
Since the FINISHED state is removed, the API rte_eal_wait_lcore
is updated to always return the status of the last function that
ran in the worker core.
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Ola Liljedahl <ola.liljedahl@arm.com>
Reviewed-by: Feifei Wang <feifei.wang2@arm.com>
Add support for configurable number of loops through the input PCAP
file for the source port. Added an additional parameter to source
port CLI command.
Signed-off-by: Yogesh Jangra <yogesh.jangra@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Fix the mbuf offload flags namespace by adding an RTE_ prefix to the
name. The old flags remain usable, but a deprecation warning is issued
at compilation.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
The flags PKT_TX_VLAN_PKT and PKT_TX_QINQ_PKT are
marked as deprecated since commit 380a7aab1a ("mbuf: rename deprecated
VLAN flags") (2017). But they were not using the RTE_DEPRECATED
macro, because it did not exist at this time. Add it, and replace
usage of these flags.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to have 'rte_eth' prefix.
All internal components switched to using new names.
Syntax fixed on lines that this patch touches.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Chenbo Xia <chenbo.xia@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
When a vdev is removed in destroy_device function,
the corresponding vhost TX buffer will also be freed,
but the vhost TX buffer may still be used in the
drain_vhost function, which will cause an error of
heap-use-after-free. Therefore, before accessing
vhost TX buffer, we need to check whether the vdev
has been removed, if so, let's skip this vdev.
Fixes: a68ba8e0a6 ("examples/vhost: refactor vhost data path")
Cc: stable@dpdk.org
Signed-off-by: Wenwu Ma <wenwux.ma@intel.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
This commit adds the per-port hints added to the eventdev API, indicating
which eventdev ports will be used for producing, forwarding, or consuming
events from the system.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Added changes to receive packets as event vector. By default this is
disabled and can be enabled using the option --event-vector. Vector
size and timeout to form the vector can be configured using options
--event-vector-size and --event-vector-tmo.
Example:
dpdk-l2fwd-event -l 0-3 -n 4 -- -p 0x03 --mode=eventdev \
--eventq-sched=ordered --event-vector --event-vector-size 16
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Added changes to receive packets as event vector. By default this is
disabled and can be enabled using the option --event-vector. Vector
size and timeout to form the vector can be configured using options
--event-vector-size and --event-vector-tmo.
Example:
dpdk-l3fwd -l 0-3 -n 4 -- -p 0x03 --mode=eventdev \
--eventq-sched=ordered --event-vector --event-vector-size 16
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Removing 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag.
Instead of drivers announce this capability, application can deduct the
capability by checking reported 'dev_info.max_mtu' or
'dev_info.max_rx_pktlen'.
And instead of application setting this flag explicitly to enable jumbo
frames, this can be deduced by driver by comparing requested 'mtu' to
'RTE_ETHER_MTU'.
Removing this additional configuration for simplification.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Michal Krawczyk <mk@semihalf.com>
There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
As described in [1] and as announced in [2], The field ``dataunit_len``
of the ``struct rte_crypto_cipher_xform`` moved to the end of the
structure and extended to ``uint32_t``.
In this way, sizes bigger than 64K bytes can be supported for data-unit
lengths.
[1] commit d014dddb2d ("cryptodev: support multiple cipher
data-units")
[2] commit 9a5c09211b ("doc: announce extension of crypto data-unit
length")
Signed-off-by: Matan Azrad <matan@nvidia.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
In inline protocol inbound SA's, plain IPv4 and IPv6 packets are
delivered to application unlike inline crypto or lookaside.
Hence fix the application to not drop them when working in
single SA mode.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Remove the unnecessary header file rte_atomic.h
included in example module.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Signed-off-by: Dharmik Thakkar <dharmik.thakkar@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic32_test_and_set to compiler CAS atomic
operation for display_stats sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic32_cmpset to compiler atomic CAS
operation for channel status sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic usages to compiler atomic built-ins
for stats_read_pending sync in l2fwd_jobstats module.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic usages to compiler atomic built-ins
for thread sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic usages to compiler atomic builit-ins
for kni_stop and kni_pause sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic32_test_and_set usage to compiler atomic
CAS operation for display_stats sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Convert rte_atomic usages to compiler atomic built-ins
for global_exit_flag sync.
Signed-off-by: Joyce Kong <joyce.kong@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Use mbuf packet type for traffic identification as
packet is parsed already by HW before and HW/PMD updates
necessary info in mbuf packet type of the found protocols.
This change is specifically for event mode.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
The env.digest memory was freed, but the pointer was not set to NULL
afterwards. This caused an "Invalid Memory" error, as the pointer tries
to free twice.
Fixes: 952e10cdad ("examples/fips_validation: support scatter gather list")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Fan Zhang <roy.fan.zhang@intel.com>
The val.val pointer is allocated memory, however this memory is then
freed in get_writeback_data() without being used beforehand.
The pointer is then allocated memory again before use,
so the very first allocation is removed as it was unnecessary.
Fixes: f4797bae00 ("examples/fips_validation: support plain SHA")
Cc: stable@dpdk.org
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Fan Zhang <roy.fan.zhang@intel.com>
Definition of `rte_ether_addr` structure used a workaround allowing DPDK
and Windows SDK headers to be used in the same file, because Windows SDK
defines `s_addr` as a macro. Rename `s_addr` to `src_addr` and `d_addr`
to `dst_addr` to avoid the conflict and remove the workaround.
Deprecation notice:
https://mails.dpdk.org/archives/dev/2021-July/215270.html
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
This patch adds dev_close() step to release network adapter resources
when kni free.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Soft expiry is not a mandatory IPsec feature. It is verified separately
with IPsec unit tests. So configuration of the same is not required.
Also, soft expiry tracking can cause perf degradation with some PMDs.
Since a separate UT is available and the same setting in ipsec-secgw is
not verifying the functionality, remove the same by clearing life
configuration.
Signed-off-by: Anoob Joseph <anoobj@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Add SA lifetime configuration to register soft and hard expiry limits.
Expiry can be in units of number of packets or bytes. Crypto op
status is also updated to include new field, aux_flags, which can be
used to indicate cases such as soft expiry in case of lookaside
protocol operations.
In case of soft expiry, the packets are successfully IPsec processed but
the soft expiry would indicate that SA needs to be reconfigured. For
inline protocol capable ethdev, this would result in an eth event while
for lookaside protocol capable cryptodev, this can be communicated via
`rte_crypto_op.aux_flags` field.
In case of hard expiry, the packets will not be IPsec processed and
would result in error.
Signed-off-by: Anoob Joseph <anoobj@marvell.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Documentation specifies that flow port & queue is provided as,
<...> port 0 queue 0
But code is expecting the same as,
<...> port 0 0
Fix the above to match documentation.
Fixes: 8e693616fc ("examples/ipsec-secgw: enable flow based distribution")
Cc: stable@dpdk.org
Signed-off-by: Anoob Joseph <anoobj@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Update mbuf.l2_len with L2 header size for outbound
inline processing.
This patch also fixes a bug in arg parsing.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
The arguments of actions that are learned are now specified as part of
the learn instruction as opposed to being statically specified as part
of the learner table configuration.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Copy threshold has been introduced in async vhost data
path to select the appropriate copy engine to do copies
for higher efficiency.
However, it may cause packets ordering issues and also
introduces performance unpredictability.
Therefore, this patch removes copy threshold support in
async vhost data path.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
The example has various profiles to run services on specified
number of lcores. Due to incorrect boundary condition, service
can be dispatched to a core that does not exist. This puts main
core into endless wait.
Max available number of service cores is all detected lcores
excluding main core.
Fixes: 7f6ee6aee7 ("examples/service_cores: check cores before run")
Cc: stable@dpdk.org
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Added macros to simplify print of MAC address.
The six bytes of a MAC address are extracted in
a macro here, to improve code readablity.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added macro to print six bytes of MAC address.
The MAC addresses will be printed in upper case
hexadecimal format.
In case there is a specific check for lower case
MAC address, the user may need to make a change in
such test case after this patch.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Some of the cryptodev APIs are not allowed to be used
by application directly. Hence removing the usage of
1. queue_pair_release: it is not required, as configure
of queue pair release the previous queue pairs and the
dev is not directly exposed to application, hence cannot
use its ops from app.
2. rte_cryptodev_stop: it can be used directly without
checking if the device is started or not.
3. rte_cryptodev_pmd_destroy: application should use
rte_cryptodev_close instead.
Signed-off-by: Akhil Goyal <gakhil@marvell.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The API rte_cryptodev_pmd_is_valid_dev, can be used
by the application as well as PMD to check whether
the device is valid or not. Hence, _pmd is removed
from the API.
The applications and drivers which use this API are
also updated.
Signed-off-by: Akhil Goyal <gakhil@marvell.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
In clang 12.0.1 version, the use of pthread_yield() is deprecated,
use sched_yield() instead.
log:
examples/performance-thread/pthread_shim/main.c:75:9: warning:
'pthread_yield' is deprecated: pthread_yield is deprecated,
use sched_yield instead [-Wdeprecated-declarations]
Bugzilla ID: 745
Fixes: 433ba6228f ("examples/performance-thread: add pthread_shim app")
Cc: stable@dpdk.org
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Tested-by: Ali Alnubani <alialnu@nvidia.com>
Currently the sample app user guides use hard coded code snippets,
this patch changes these to use literalinclude which will dynamically
update the snippets as changes are made to the code.
This was introduced in commit 413c75c33c ("doc: show how to include
code in guides"). Comments within the sample apps were updated to
accommodate this as part of this patch. This will help to ensure that
the code within the sample app user guides is up to date and not out
of sync with the actual code.
Signed-off-by: Conor Fogarty <conor.fogarty@intel.com>
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
The support for multiple data-units includes the next:
- Add a new command-line argument to provide the data-unit length.
- Set the length in the cipher xform.
- Validate device capabilities for this feature.
- Pad the AES-XTS operation length to be aligned to the defined data-unit.
Signed-off-by: Matan Azrad <matan@nvidia.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Set the Rx multi-queue mode to NONE when configuring a port that is
associated with hardware that only supports a single Rx queue.
Signed-off-by: Chaoyong He <chaoyong.he@corigine.com>
Signed-off-by: Heinrich Kuhn <heinrich.kuhn@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
When the guest memory is hotplugged, the vhost application which
enables DMA acceleration must stop DMA transfers before the vhost
re-maps the guest memory.
To accomplish that, we need to do these changes in the vhost sample:
1. add inflight packets count.
2. add vring_state_changed() callback.
3. add inflight packets clear process in destroy_device() and
vring_state_changed().
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
The async vhost callback ops should return negative value when there
are something wrong in the callback, so the return type should be
changed into int32_t. The issue in vhost example is also fixed.
Fixes: cd6760da10 ("vhost: introduce async enqueue for split ring")
Fixes: 819a716858 ("vhost: fix async callback return type")
Fixes: 6b3c81db8b ("vhost: simplify async copy completion")
Fixes: abec60e711 ("examples/vhost: support vhost async data path")
Fixes: 6e9a9d2a02 ("examples/vhost: fix ioat dependency")
Fixes: 873e8dad6f ("vhost: support packed ring in async datapath")
Cc: stable@dpdk.org
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch reworks the async configuration structure to improve code
readability. In addition, add preserved padding fields on the structure
for future usage.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Fix the incorrect array out of bounds check within the function
pipeline_selector_group_member_read().
Coverity issue: 371911
Fixes: 598fe0dd0d ("examples/pipeline: support selector table")
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch fixes the following build failures seen on Ubuntu 16.04
with gcc 5.4.0 because of uninitialized variables:
...
examples/pipeline/cli.c:1559:11: error: 'weight_val' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:1545:13: error: 'member_id_val' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:1538:12: error: 'group_id_val' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2189:2: error: 'idx1' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2179:43: error: 'idx0' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2265:2: error: 'idx1' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2248:43: error: 'idx0' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2358:2: error: 'idx1' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
...
examples/pipeline/cli.c:2325:43: error: 'idx0' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
Fixes: 598fe0dd0d ("examples/pipeline: support selector table")
Signed-off-by: Ali Alnubani <alialnu@nvidia.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
The PMD Power Management scheme currently has 3 modes,
scale, monitor and pause. However, it would be nice to
have a baseline mode for easy comparison of power savings
with and without these modes.
This patch adds a 'baseline' mode were the PMD power
management is not enabled. Use --pmd-mgmt=baseline.
Signed-off-by: David Hunt <david.hunt@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Add example for FIB with VRF and ECMP support.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Churchill Khangar <churchill.khangar@intel.com>
For more flexibility, the single monolithic table update command is
split into table entry add, table entry delete, table default entry
add, pipeline commit and pipeline abort.
Signed-off-by: Churchill Khangar <churchill.khangar@intel.com>
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Currently, l3fwd-power enforces the limitation of having one queue per
lcore. This is no longer necessary, so remove the limitation.
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Tested-by: David Hunt <david.hunt@intel.com>
This patch aligns the l3fwd EM code with the changes made to LPM in
commit 74fb854a3d ("examples/l3fwd: remove useless reloads in LPM
main loop").
This change ensures the compiler knows that the lcore config variables
are constant values and the compiler will then optimize the code
accordingly.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
This patch aligns the l3fwd FIB code with the changes made to LPM in
commit 74fb854a3d ("examples/l3fwd: remove useless reloads in LPM
main loop").
This change ensures the compiler knows that the lcore config variables
are constant values and the compiler will then optimize the code
accordingly.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
The "mac-updating" option can be removed since the associated mac_updating
variable is set to 1 by default.
Signed-off-by: Chenglian Sun <sunchenglian@loongson.cn>
Reviewed-by: David Marchand <david.marchand@redhat.com>
For l2fwd, --no-mac-updating and --mac-updating are treated as invalid
arguments. Rework long options parsing to let --no-mac-updating and
--mac-updating options work well.
Fixes: fa19eb20d2 ("examples/l2fwd: add forwarding port mapping option")
Cc: stable@dpdk.org
Signed-off-by: Chenglian Sun <sunchenglian@loongson.cn>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Number of rx queue and number of rx port in lcore config are constants
during the period of l3 forward application running. But compiler has
no this information.
Copied values from lcore config to local variables and used the local
variables for iteration. Compiler can see that the local variables are
not changed, so qconf reloads at each iteration can be eliminated.
The change showed 1.8% performance uplift in single core, single port,
single queue test on N1SDP platform with MLX5 NIC.
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Both L2 and L3 headers will be used in forward processing. And these
two headers are in the same cache line. It has the same effect for
prefetching with L2 header address and prefetching with L3 header
address.
Changed to use L2 header address for prefetching. The change showed
no measurable performance improvement, but it definitely removed
unnecessary instructions for address calculation.
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Fix assignment errors of ep_hgh_edpi in function parse_ep_config.
Fixes: a137d012a0 ("examples/l3fwd-power: support traffic pattern aware control")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Reshma Pattan <reshma.pattan@gmail.com>
Acked-by: David Hunt <david.hunt@intel.com>
According to the comments and logging, the author just hope user to use
the core and device which are in the same numa node for optimal
performance. If not, A warning gives out.
This patch fixes the check for a device on the node 0.
Fixes: 7107e471a6 ("examples/skeleton: very simple code for packet forwarding")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
According to the comments and logging, the author just hope user to use
the core and device which are in the same numa node for optimal
performance. If not, A warning gives out.
This patch fixes the check for a device on the node 0.
Fixes: f6baccbc2b ("examples/l2fwd-cat: add sample application for PQoS CAT and CDP")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
According to the comments and logging, the author just hope user to use
the core and device which are in the same numa node for optimal
performance. If not, A warning gives out.
For example in flow_classify:
./build/flow_classify -a 0000:7d:00.1 -l 93
Here:
0000:7d:00.1 is on numa node 0.
core 93 is on numa node 3.
The two are not in same numa node, but no warning gives out in old codes
when device is on node 0.
This patch includes the node 0 in the check.
Fixes: bab16ddaf2 ("examples/flow_classify: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Tested-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This fixes -Wformat warning with clang 10.0.0 on Windows.
Fixes: f8244c6399 ("ethdev: increase port id range")
Cc: stable@dpdk.org
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Timer sample example assumes that the frequency of the timer is about
2Ghz to control the period of calling rte_timer_manage(). But this
assumption is easy to fail. For example. the frequency of tsc on ARM64
is much less than 2Ghz.
This patch uses the frequency of the current timer to calculate the
correct time interval to ensure consistent result on all platforms.
In addition, the rte_rdtsc() is replaced with the more recommended
rte_get_timer_cycles function in this patch.
Fixes: af75078fec ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Recent patch to support UDP encapsulation introduced problem with
handling inbound IPv6 packets with header extensions.
This patch aims to fix the issue.
Bugzilla ID: 695
Fixes: 9a1cc8f1ed ("examples/ipsec-secgw: support UDP encapsulation")
Reported-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
VM channel number should not be validated against the
host vm_power_manager coremask core indexes, as VM
cores need not to be same as host cores.
So remove this check, to allow all the vm channels
to be added successfully.
Fixes: b49c677a0d ("examples/vm_power: respect core mask")
Cc: stable@dpdk.org
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Reviewed-by: David Hunt <david.hunt@intel.com>
Move pkg-config override to beginning in the Makefile to allow
use PKGCONF variable to detect the libdpdk availability.
Fixes: fda34680eb ("examples: remove legacy sections of makefiles")
Cc: stable@dpdk.org
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The vhost library currently configures Tx offloading (PKT_TX_*) on any
packet received from a guest virtio device which asks for some offloading.
This is problematic, as Tx offloading is something that the application
must ask for: the application needs to configure devices
to support every used offloads (ip, tcp checksumming, tso..), and the
various l2/l3/l4 lengths must be set following any processing that
happened in the application itself.
On the other hand, the received packets are not marked wrt current
packet l3/l4 checksumming info.
Copy virtio rx processing to fix those offload flags with some
differences:
- accept VIRTIO_NET_HDR_GSO_ECN and VIRTIO_NET_HDR_GSO_UDP,
- ignore anything but the VIRTIO_NET_HDR_F_NEEDS_CSUM flag (to comply with
the virtio spec),
Some applications might rely on the current behavior, so it is left
untouched by default.
A new RTE_VHOST_USER_NET_COMPLIANT_OL_FLAGS flag is added to enable the
new behavior.
The vhost example has been updated for the new behavior: TSO is applied to
any packet marked LRO.
Fixes: 859b480d5a ("vhost: add guest offload setting")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
We use ioat ring space for determining if ioat callbacks can enqueue a
packet to ioat device. But there is one slot can't be used in ioat
ring due to the ioat driver design, so we need to reduce one slot in
ioat ring to prevent ring size mismatch in ioat callbacks.
Fixes: 2aa47e94bf ("examples/vhost: add ioat ring space count and check")
Cc: stable@dpdk.org
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Add improved error handling to rte_ioat_completed_ops(). This patch adds
new parameters to the function to enable the user to track the completion
status of each individual operation in a batch. With this addition, the
function can help the user to determine firstly, how many operations may
have failed or been skipped and then secondly, which specific operations
did not complete successfully.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Running "./devtools/check-meson.py --fix" on the DPDK repo fixes a
number of issues with whitespace and formatting of files:
* indentation of lists
* missing trailing commas on final list element
* multiple list entries per line when list is not all single-line
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The commit a8f8b672d5 ("examples/l3fwd: skip Tx queue drain on first iteration")
implemented a change to the EM and LPM lookup methods to
prevent the Tx queue drain running in the first iteration of their
packet processing loops.
This patch applies the same change into the new FIB lookup method.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
The new_mtu was assigned twice, the first assignment could be removed.
Fixes: bda68ab9d1 ("examples/ethtool: add user-space ethtool sample application")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
According to the programming guide, the rte_eal_init should be used pairs
with rte_eal_cleanup.
This patch add rte_eal_cleanup to examples to encourage new users of
DPDK to use it.
Fixes: aec9c13c52 ("eal: add function to release internal resources")
Fixes: 3d0fad56b7 ("examples/fips_validation: add crypto FIPS application")
Fixes: c8e6ceeceb ("examples/ioat: add new sample app for ioat driver")
Fixes: 4ff457986f ("examples/l2fwd-event: add default poll mode routines")
Fixes: 08bd1a1744 ("examples/l3fwd-graph: add graph-based l3fwd skeleton")
Fixes: c5eebf85ba ("examples/ntb: add example for NTB")
Fixes: b77f660028 ("examples/pipeline: add new example application")
Fixes: edbed86d1c ("examples/vdpa: introduce a new sample for vDPA")
Fixes: c19beb3f38 ("examples/vhost_blk: introduce vhost storage sample")
Fixes: f5188211c7 ("examples/vhost_crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
This patch supports set ctrl worker thread name which is helpful for
debugging.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports set helloworld thread name which is helpful for
debugging.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
As with the lib and drivers directories, we can use "continue" keyword to
reduce the indentation level of the majority of the foreach block. At the
same time, we can also replace tab indentation with spaces.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Each table entry is made up of match fields and action data, with the
latter made up of the action ID and the action arguments. The approach
of having the user specify explicitly the endianness of the action
arguments is difficult to be picked up by P4 compilers, as the P4
compiler is generally unaware about this aspect.
This commit introduces the auto-detection of the endianness of the
action arguments by examining the endianness of the their destination:
network byte order (NBO) when they get copied to headers and host byte
order (HBO) when they get copied to packet meta-data or mailboxes.
The endianness specification of each action argument as part of the
rule specification, e.g. H(...) and N(...) is removed from the rule
file and auto-detected based on their destination. The DMA instruction
scope is made internal, so mov instructions need to be used. The
pattern of transferring complete headers from table entry action args
to headers is detected, and the associated set of mov instructions
plus header validate is internally detected and replaced with the
internal-only DMA instruction to preserve performance.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
This patch implements the Forwarding Information Base (FIB) library
in l3fwd using the function calls and infrastructure introduced in
the previous patch.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
The purpose of this commit is to add the necessary function calls
and supporting infrastructure to allow the Forwarding Information Base
(FIB) library to be integrated into the l3fwd sample app.
Instead of adding an individual flag for FIB, a new flag '--lookup' has
been added that allows the user to select their desired lookup method.
The flags '-E' and '-L' have been retained for backwards compatibility.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
To prevent code duplication from the addition of lookup methods
the routes specified in lpm should be moved to a common header.
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Any IP within the 2001:200::/48 subnet will match all the routes given
instead of 1 individual route and the application cannot
differentiate between them.
The change in this patch allows the ports to be individually matched using
smaller /64 ranges for each port. These smaller subnet ranges are still
within the 2001:200::/48 subnet range set aside for benchmarking
in RFC5180.
l3fwd will now use 2001:200:0:{0-7}::/64 where 0-7 is the port ID for IPv6.
Fixes: 37afe381bd ("examples/l3fwd: use reserved IP addresses")
Cc: stable@dpdk.org
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Initialize prev_tsc to cur_tsc. This avoids running the TX queue drain
in the first iteration of the packet processing loop.
Signed-off-by: Kathleen Capella <kathleen.capella@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
This patch deletes the comments which are wrong and unnecessary.
Fixes: ab129e9065 ("examples/ptpclient: add minimal PTP client")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add support for table statistics for the SWX pipeline. For each table,
we maintain a counter for lookup hit packets, one for lookup miss
packets and one packet counter for each table action.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Signed-off-by: Yogesh Jangra <yogesh.jangra@intel.com>
Enabled the TX instruction to accept an immediate value for the output
port argument. The drop instruction is simply an alias to the TX
instruction for the last output port of the pipeline.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
In the example application the key can be provided by the user or
generated randomly by the example application.
Then a validation is done in order to check if the key size is
supported in the algorithm capabilities.
A new feature flag is added in crypto PMDs to allow wrapped keys,
hence, to allow wrapped keys, app should remove the validation of
key size in the application and rely on a PMD key size validation.
The validation is removed in case the key is provided by user and
the RTE_CRYPTODEV_FF_CIPHER_WRAPPED_KEY feature flag is set, and
kept in case the key should be generated by the application or
RTE_CRYPTODEV_FF_CIPHER_WRAPPED_KEY is not set.
Signed-off-by: Shiri Kuzin <shirik@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Adding lookaside IPsec UDP encapsulation support
for NAT traversal.
Application has to add udp-encap option to sa config file
to enable UDP encapsulation on the SA.
Signed-off-by: Tejasree Kondoj <ktejasree@marvell.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
There were some padding left when a packet gets decrypted. This
patch removes those padding.
This patch also removes the padding left after verifying auth of
the packet.
Fixes: e2cdfbd07c ("examples/l2fwd-crypto: fix port id type")
Cc: stable@dpdk.org
Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
The devices which are masked by cryptodev mask should not be initialized
and skipped while traversing the device list.
Fixes: 6ae3fb9df6 ("examples/l2fwd-crypto: fix session mempool size")
Cc: stable@dpdk.org
Signed-off-by: Apeksha Gupta <apeksha.gupta@nxp.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
L2fwd-crypto is passing 24b private data size while packet
pool creation. This patch aligns that private data size
to cache line size for better performance results.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Acked-by: Akhil Goyal <gakhil@marvell.com>
Users of <rte_ip.h> relied on it to provide IP-related defines,
like IPPROTO_* constants, but still had to include POSIX headers
for inet_pton() and other standard IP-related facilities.
Extend <rte_ip.h> so that it is a single header to gain access
to IP-related facilities on any OS. Use it to replace POSIX includes
in components enabled on Windows. Move missing constants from Windows
networking shim to OS shim header and include it where needed.
Remove Windows networking shim that is no longer needed.
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Ranjit Menon <ranjit.menon@intel.com>
In current design, legacy parser rte_devargs_parse() saved scratch
buffer to devargs.args while new parser rte_devargs_layers_parse() saved
to devargs.data. Code using devargs had to know the difference and
cleaned up memory accordingly - error prone.
This patch unifies scratch buffer to data field, introduces
rte_devargs_reset() function to wrap the memory clean up logic.
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Reviewed-by: Gaetan Rivet <grive@u256.net>
Short option "s" was passed to getopt_long function, while there was
no condition on this option.
Fixes: f5188211c7 ("examples/vhost_crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Ibtisam Tariq <ibtisam.tariq@emumba.com>
Acked-by: Fan Zhang <roy.fan.zhang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch fixes unchecked return value for rte_vhost_get_mem_table(),
which is reported by coverity.
Coverity issue: 364233
Fixes: ca059fa5e2 ("examples/vhost: demonstrate the new generic APIs")
Cc: stable@dpdk.org
Signed-off-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Avoid calling rte_vhost_get_vhost_ring_inflight() and
rte_vhost_get_vring_base_from_inflight() when
VHOST_USER_PROTOCOL_F_INFLIGHT_SHMFD is not set.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Meter arrays are stateful objects that are updated by the data plane
and configured & monitored by the control plane. The meters implement
the RFC 2698 Two Rate Three Color Marker (trTCM) algorithm.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
