Changes:
- add new message sqs_alloc in mailbox
- add a queue container to hold secondary qsets.
- add nicvf_mbox_request_sqs
- handle new mailbox messages for secondary queue set support
- register secondary queue sets for further reuse
- register the number secondary queue sets in MSG_QS_CFG
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This interface (nicvf_bsvf) will be used for secondary queue set support.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The symbols PKT_TX_TCP_CKSUM and PKT_TX_UDP_CKSUM are not bits on a
bitmask. Set l3_offset always for TX offloads, not just for PKT_TX_IP_CKSUM
being true.
Fixes: 1c421f18e0 ("net/thunderx: add single and multi-segment Tx")
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Decode the checksum flags from the Rx descriptor, setting
the appropriate bit in the mbuf ol_flags field when the flag
indicates a bad checksum.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Signed-off-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The ptype is decoded from the Rx descriptor and stored
in the packet type field in the mbuf using the same function
in the non-vector driver.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Signed-off-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
SR-IOV virtual functions cannot rely on promiscuous mode for the reception
of VLAN tagged frames. Program the VLAN filter for each slave when a
VLAN is configured for the bonding master.
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
It's possible for the bonding driver to mistakenly reject an interface
based in it's, as yet, unnegotiated link speed and duplex. Always allow
the interface to be added to the bonding interface but require link
properties validation to succeed before slave is activated.
Fixes: 2efb58cbab ("bond: new link bonding library")
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Add the ability to reset the virtio device in the configure callback
if the features flag changed since previous reset. This will be possible
with the introduction of offload support in next commits.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Move the configuration of control queue in the configure callback.
This is needed by next commit, which introduces the reinitialization
of the device in the configure callback to change the feature flags.
Therefore, the control queue will have to be restarted at the same
place.
As virtio_dev_cq_queue_setup() is called from a place where
config->max_virtqueue_pairs is not available, we need to store this in
the private structure. It replaces max_rx_queues and max_tx_queues which
have the same value. The log showing the value of max_rx_queues and
max_tx_queues is also removed since config->max_virtqueue_pairs is
already displayed above.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Move all code related to device initialization in a new function
virtio_init_device().
This commit brings no functional change, it prepares the next commits
that will add the offload support. For that, it will be needed to
reinitialize the device from ethdev->configure(), using this new
function.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add an option, dequeue-zero-copy, to enable this feature in vhost-pmd.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Negotiate VIRTIO_F_IOMMU_PLATFORM to have IOMMU support.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add modern device id and rename VIRTIO_PCI_DEVICEID_MIN to
VIRTIO_PCI_LEGACY_DEVICEID_NET. While at it, remove unused macros too.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The driver name has been lost with the eal rework.
Restore it.
Fixes: c830cb2954 ("drivers: use PCI registration macro")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Virtio interfaces do not currently allow the user to specify a particular
Maximum Transmission Unit (MTU). Consequently, the MTU of Virtio interfaces
is typically set to the Ethernet default value of 1500.
This is problematic in the case of cloud deployments, in which a specific
(and potentially non-standard) MTU needs to be set by a DHCP server, which
needs to be honored by all interfaces across the traffic path.To acheive
this Virtio interfaces should support setting of MTU.
In case when GRE/VXLAN tunneling is used for internal communication, there
will be an overhead added by the infrastructure in the packet over and
above the ETHER MTU of 1518. So to take care of this overhead in these
cases the DHCP server corrects the L3 MTU to 1454. But since virtio
interfaces was not having the MTU set functionality that MTU sent by the
DHCP server was ignored and the instance will still send packets with 1500
MTU which after encapsulation will become more than 1518 and eventually
gets dropped in the infrastructure.
By adding an additional 'set_mtu' function to the Virtio driver, we can
honor the MTU sent by the DHCP server. The dhcp server/controller can
then leverage this 'set_mtu' functionality to resolve the above
mentioned issue of packets getting dropped due to incorrect size.
Signed-off-by: Souvik Dey <sodey@sonusnet.com>
Reviewed-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
To enable Tx side offload on tunneling packet, driver should set
correct tunneling parameters: (1) EIPT, External IP header type;
(2) EIPLEN, External IP; (3) L4TUNT; (4) L4TUNLEN. This parsing
behavior is based on (ol_flag & PKT_TX_TUNNEL_MASK). And when
it's a tunneling packet, MACLEN defines the outer L2 header.
Also, we define TSO on each kind of tunneling type as a capabilities.
Now only i40e declares to support them.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Inline with PCI probe and remove, VDEV probe and remove hooks provide
a uniform naming.
PCI probe represents scan and driver initialization. For VDEV, it will
represent argument parsing and initialization.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different auto generated
file.
Structures updated:
hwrm_stat_ctx_alloc_input, hwrm_stat_ctx_alloc_output,
hwrm_stat_ctx_free_input, hwrm_stat_ctx_free_output,
hwrm_stat_ctx_clr_stats_input, hwrm_stat_ctx_clr_stats_output,
hwrm_exec_fwd_resp_input, hwrm_exec_fwd_resp_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use packet filtering related structures as per the
1.5.1 version of the HWRM API. Most of the changes in the patch are
white spaces and rearrangement of the lines - a onetime change owing to
the usage of a different auto generated file.
Structures being updated:
hwrm_cfa_l2_filter_cfg_input, hwrm_cfa_l2_filter_cfg_output,
hwrm_cfa_l2_set_rx_mask_input, hwrm_cfa_l2_set_rx_mask_output,
hwrm_cfa_l2_filter_alloc_input, hwrm_cfa_l2_filter_alloc_output,
hwrm_cfa_l2_filter_free_input, hwrm_cfa_l2_filter_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use HWRM ring related structures as per the 1.5.1
version of the HWRM API. Most of the changes in the patch are white
spaces and rearrangement of the lines - a onetime change owing to the
usage of a different auto generated file.
Structures being updated:
hwrm_ring_alloc_input, hwrm_ring_alloc_output, hwrm_ring_free_input,
hwrm_ring_free_output, hwrm_ring_grp_alloc_input,
hwrm_ring_grp_alloc_output, hwrm_ring_grp_free_input,
hwrm_ring_grp_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use VNIC related structures as per the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures being updated:
hwrm_vnic_alloc_input, hwrm_vnic_alloc_output, hwrm_vnic_free_input,
hwrm_vnic_free_output, hwrm_vnic_cfg_input, hwrm_vnic_cfg_output,
hwrm_vnic_rss_cfg_input, hwrm_vnic_rss_cfg_output,
hwrm_vnic_rss_cos_lb_ctx_alloc_input,
hwrm_vnic_rss_cos_lb_ctx_alloc_output,
hwrm_vnic_rss_cos_lb_ctx_free_input,
hwrm_vnic_rss_cos_lb_ctx_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures updated:
hwrm_func_qcfg_input, hwrm_func_qcfg_output, hwrm_func_drv_rgtr_input,
hwrm_func_drv_rgtr_output, hwrm_func_drv_unrgtr_input,
hwrm_func_drv_unrgtr_output, hwrm_queue_qportcfg_input,
hwrm_queue_qportcfg_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures being updated in this patch:
input, output, hwrm_ver_get_input, hwrm_ver_get_output,
hwrm_func_reset_input, hwrm_func_reset_output, hwrm_func_qcaps_input,
hwrm_func_qcaps_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use structures as per the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - hopefully a onetime change owing to the usage of a different
auto generated file.
Structures updated:
cmpl_base, tx_cmpl, rx_pkt_cmpl, rx_pkt_cmpl_hi, hwrm_fwd_req_cmpl,
hwrm_async_event_cmpl
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - hopefully a onetime change owing to the usage of a different
auto generated file.
Structures updated in this patch:
tx_bd_short, tx_bd_long, tx_bd_long_hi, rx_prod_pkt_bd
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in this patch and the following patches are
white spaces and rearrangement of the lines - hopefully a onetime change
owing to the usage of a different auto generated file.
Other than that, the following fields have been renamed:
1) rx_err_pkts and tx_err_pkts are now rx_discard_pkts and tx_discard_pkts
in struct ctx_hw_stats64
2) the perm_mac_addr field in the response of bnxt_hwrm_func_qcaps has
changed to mac_addr.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support to the bnxt PMD to load on a PCI VF.
1) VF cannot change parameters like - speed, autoneg and pause
2) If the VF MAC address shows up as all 0's it has to be provisioned
by the PF in the hypervisor.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
More PCI Device IDs for Cumulus, Cumulus+ and Whitney, Whitney+ SKUs.
The NPAR model supported by firmware has been altered. It now allocates a
unique Device ID for each NPAR partition for each device. In addition,
ASIC's that are capable of supporting dual media have a unique DID
depending whether they are configured in copper or fiber mode.
This patch adds the necessary DIDs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Adding code to enable support for NIC Partitioning or NPAR 1.0
As a part of NPAR, we don't allow port settings like speed or flow
control to be changed.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds support for the Broadcom StrataGX® BCM5871X
series of Communications Processors.
These ARM based processors target a broad range of networking
applications including virtual CPE (vCPE) and NFV appliances,
10G service routers and gateways, control plane processing for
Ethernet switches, and network attached storage (NAS).
Other than adding the PCI Id for supporting the device,
the patch also adds a memory barrier before the Tx doorbell
and Completing ring doorbell is written to. Since ARM has a
weakly ordered memory model this enforces a strict ordering
of the descriptor writes before the doorbell writes happen.
Signed-off-by: John Carney <john.carney@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The ixgbe base driver was updated to version
cid-10g-shared-code.2016.04.12.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Change the parameter bypass_vlvf to vlvf_bypass for consistency
with ixgbe_common.c.
Clean up some whitespace and misalignment.
Change variable type of secrxreg from int to u32 as it's used
to store register value.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
By exiting early we could skip the PHY configuration and as such
the driver may not configure the PHY correctly for SFP+.
This patch removes the logic which would previously skip the PHY
configuration in the case where we are already at the requested
speed in ixgbe_setup_mac_link_multispeed_fiber().
Fixes: f3430431ab ("ixgbe/base: add SFP+ dual-speed support")
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Support for flow control auto negotiation is defeatured from X550em_a
fiber when connected to speeds lower than 10Gbps. This patch cleans up
the code path which is mostly dead to begin with.
- add device IDs check in ixgbe_device_supports_autoneg_fc().
- ixgbe_fc_autoneg_fiber_x550em_a() is now used only to pass the user
settings to ixgbe_fc_enable_generic().
- make sure that start_hw does not fail when setup_fc is not implemented.
- small fix in the debug message when ixgbe_device_supports_autoneg_fc()
returns false.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Correct link flow for X550em_a backplane with ALEF.
Report the correct link capabilities:
SKUs configured for 2.5G only support 2.5G.
non-10G SKUs can only support 2.5 or 1G.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently, not all shadow RAM accesses are being done under the
protection of a semaphore, which could result in corruption.
Refactor the code so that it is possible to hold the semaphore
around ixgbe_host_interface_command by introducing an unlocked form.
This patch also eliminates the function ixgbe_read_ee_hostif_data_X550
in favor of the function ixgbe_read_ee_hostif_X550.
The new arrangement is able to get both the management interface semaphore
and the EEPROM semaphore at the same time instead of separately.
Fixes: af75078fec ("first public release")
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds negotiate_api_version and set_rlpml into mac_ops. With the
introduction of Hyper-V functionality, we can have separate functions to
accommodate different implementations without have one break the other.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds X550em_a FW ALEF support. ALEF is the new unified FW.
The driver uses the KRM_PMD_RX_FLEX_PORT/FLX_MASK_ST20 registers to
configure the lane mode.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch moves PHY ops pointers initialization to
ixgbe_init_phy_ops_X550em and PHY identifying/initializing
to ixgbe_identify_phy_x550em.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch changes the value of IXGBE_LINK_SPEED_10_FULL from 4 to 2,
as 4 is reserved to 100Mbit Half Duplex in E1000 shared code.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Make sure ixgbe_device_supports_autoneg_fc() returns true for the device
IDs of X550EM_A_1G_T and X550EM_A_1G_T_L.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch reduces the SWFW semaphore/PHY Token retry delay.
ixgbe_release_swfw_sync_X540: Reduce 5 ms delay after releasing
semaphore to 2 ms. HW team indicated 1 ms delay would be sufficient
for FW access.
ixgbe_acquire_swfw_sync_X540: Remove 5 ms delay after acquiring
semaphore.
ixgbe_acquire_swfw_sync_X550a: Remove 5 ms delay since there are
two 2 ms delays in the semaphore release flow.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
ixgbevf_write_msg_read_ack() is now performing mailbox write and read,
so this patch use this function to commonize mailbox write and read.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds missing FDIRSCTPM mask setting for tunneled packets.
It should be set the same way as FDIRTCPM and FDIRUDPM so that SCTP
packets can be filtered correctly.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch avoids the situation where we initialize an adapter but have not
yet set up phy.autoneg_advertised speeds. In that case we could end
up with having no autoneg speeds enabled and therefore get no link until we
reset the link and set the autoneg speeds correctly.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes the X550em_a specific check link function and uses
ixgbe_check_mac_link_generic instead. It is not necessary to
check both the MAC link register and external PHY registers when
checking the link.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Do parameter check to prevent exceptional value being written into
register.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
X550em_a adds GENEVE support by using the upper 16 bits of VXLANCTRL
to store the UDP port (VXLANCTRL.GENEVE_UDP_PORT).
This patch adds definitions that can be used to manipulate the ports
depending on which protocol is being configured.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Create flow control (FC) setup and enable functions to configure PHY
registers. These registers advertise FC settings according to the user
requested mode. On link establishment, these settings are negotiated
with the link partner to agree on the settings to use: RX and TX enabled,
TX only enabled, or FC disabled and RX enabled (which also enables TX).
Remove the part of code that performs FC auto-negotiation (AN) in
ixgbe_setup_m88 and put it in a new function to maintain consistency
with other FC AN implementations so far. Add function pointers to the
setup-fc and enable-fc functions so that they get called during init
to perform FC AN.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When HW starts, first read the NVM to see if the crosstalk fix should
be used on the given HW and cache that information in the HW structure.
When we check_link we first see if 1) NVM requests this fix 2) if
we are an SFP+ device 3) see if a module is not in the SFP+ cage.
If all the above are true then don't bother checking the link, just
say it is down.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Previously we checked return buffer for
(IXGBE_VF_SET_MACVLAN | IXGBE_VT_MSGTYPE_NACK), but this would not
work if index is not 0 and as a result NACK will not be detected.
Fixes: af75078fec ("first public release")
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch makes sure that we access IOSF registers through the
host interface command (HIC) for the majority of X550em devices.
All devices with NVM are capable of using the HIC.
For consistency all instances where the ixgbe_write_phy_reg_mdi is called
directly are converted to function pointer calls.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch will pave the way for the new VF unicast promiscuous
mode support.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Propagate return value when trying to set the maximum packet length. A
PF driver could return a NACK for this request, and the VF driver will
need to know this.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Some function comments are obviously wrong, this patch rewords them.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Fixes: 0790adeb56 ("ixgbe/base: support X550em_a device")
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Provide a DMA coalescing configuration for 10Mb link speed.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The error exit should at least try to set the page register to 0
since other code will assume that state.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds a separate function for enabling Flow Control (FC)
auto-negotiation on X550em_a:
- rename ixgbe_fc_autoneg_x550a() to ixgbe_fc_autoneg_backplane_x550em_a().
- create ixgbe_fc_autoneg_fiber_x550em_a() specifically for fiber.
- add definitions for KRM_PCS_KX_AN_LP register and related bits.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds a separate function for setting up Flow Control (FC)
on X550em_a fiber:
- rename ixgbe_setup_fc_x550a() to ixgbe_setup_fc_backplane_x550em_a().
- create ixgbe_setup_fc_fiber_x550em_a() to configure FC for fiber.
- add definitions for KRM_AN_CNTL_4 and KRM_PCS_KX_AN along with related
definitions.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add new definitions to support VF unicast promiscuous mode which
will be implemented in a later patch.
Besides, rename definitions of subdevice IDs on SFP LOM to make it
easier to distinguish.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Fully initialize X550em_a 1G PHYs; move the PHY definitions from
ixgbe_x550.h to ixgbe_phy.h, where they really belong; define
register numbers in decimal because that is how they are in the spec.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Move the PHY probe code into a separate function so that it can be
reused. A subsequent patch will use it for configurations that
provide the PHY address explicitly.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch introduces new init_ops functions for X550EM_a and X550EM_x.
This makes it easier to assign function pointers with specific
dependencies (like media type) for each MAC.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds update_xcast_mode callback in mac ops, and moves
ixgbevf_update_xcast_mode function into base code.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch uses the shared Management Data Input/output (MDIO)
functions ixgbe_read_phy_reg_x550a and ixgbe_write_phy_reg_x550a
for X550em_a 10G PHY which supports flow control auto-negotiation.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The x550a related firmware reverses the endianness of the PHY data read
and written via host interface command, so make corresponding changes
to that.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes X550em SFP iXFI setup for the drivers since there
is no released hardware production with SFP iXFI.
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The vfta_delta value rather than the pointer should be checked.
Fixes: b978f7b38c ("net/ixgbe/base: simplify VLAN management")
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Using device ID to check PHY capability is not extensible.
Now we are using PHY type to detect PHY capability.
All link speeds supported by the device are encoded into PHY type,
and PHY type value can be read by admin queue "get_phy_capability"
command at initialization stage.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Re-initialize Rq's when MTU is changed. This allows for more
efficient use of mbufs when moving from an MTU that is greater
than the mbuf size to one that is less. Also move to using Rx
scatter mode when moving from an MTU less than the mbuf size
to one that is greater.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
The function vnic_dev_free_desc_ring() didn't actually free memory. Fix
this by first changing vnic_dev_alloc_desc_ring() to use the common
allocation function, then in vnic_dev_free_desc_ring call the common
free function.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Move link check code to a new function so that it can be reused
by the interrupt handler.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
enic_disable() wasn't calling rte_intr_disable() or
rte_intr_callback_unregister(). stopping/starting a port would
result in the same interrupt callback being registered multiple
times, which would then cause it to be called multiple times on
every interrupt.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
And add read memory barrier to avoid status inconsistency
between two Rx descriptors readings.
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Add Fibre Channel Over Ethernet (FCoE) in PHY capabilities.
Add data structure for FCoE statistics collection.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Add extended PHY types to get PHY abilities for 25G, then put
PHY types for 25G into the proper field when the PHY capabilities
are queried.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Previously, PTYPE filed in the RX descriptors is not set properly
for QinQ packets. The wrong PTYPE is generated because outer Tag did
not have ORT/PIT configured, so fix this issue by configuring ORT/PIT.
This patch also changes bitmask of outer VLAN tag in L2 header
to support RSS and flow director for QinQ.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 4072d503aa ("i40e: fix VLAN bitmasks for input set")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
When using VMDQ+RSS, the queue ids used by the application are not
contiguous (see i40e_pf_config_rss). Most of the driver already handled
this, but there were a few cases where it assumed all configured queues
had been setup.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 6b45371283 ("i40e: free queue memory when closing")
Fixes: 8e109464c0 ("i40e: allow vector Rx and Tx usage")
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
In SR-IOV configuration, queues 0 - nb_rx_queues belong to VF0,
which means that with the current implementation when a reset mbox
message comes from any VF, it affects the settings of VF0.
Fix this by using PF queue index to update the correct queue.
Fixes: dbb0b8737f ("ixgbe: add vlan offload support")
Signed-off-by: Alex Zelezniak <alexz@att.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Starting rxtx before flow director config will cause driver not to
receive packets from NIC.
Signed-off-by: Wang Wei <lnykww@gmail.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In FW default settings, Ethertype 0x88A8 is treated as S-TAG,
and packets with S-TAG should be received in Port Virtualizer mode.
However, Port Virtualizer mode is not initialized in DPDK, so X710 will
drop packets with Ethertype 0x88A8.
This patch fixes this issue by turning off S-TAG identification.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The bad L4 checksum flag was set on IP packets which were not
also TCP or UDP packets. This includes ICMP, IGMP and OSPF packets.
L4 ptypes were being treated as bits instead of values within the
L4 mask causing the code to check L4 checksum in the completion
queue and incorrectly set the L4 bad checksum flag.
Fixes: 947d860c82 ("enic: improve Rx performance")
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
When testpmd quits with two ports, the second port's MAC address
remains in the MAC table of switch manager.
There needs to be some time for HW to quiesce when closing a port,
otherwise a subsequent port close won't be handled correctly.
This patch adds a delay after turning off a logic port, just as
the kernel driver does.
Fixes: 8b5c9ec20b ("fm10k: support VMDQ in MAC/VLAN filter")
Reported-by: Xueqin Lin <xueqin.lin@intel.com>
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The enic DMAs link status information to the host and this requires a
little setup. This setup was being done as a result of calling
rte_eth_dev_start(). But applications expect to be able to check link
status before calling rte_eth_dev_start().
This patch moves the link status setup to enic_init() which is called
at device probe time so that link status can be checked anytime.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
If rte_pktmbuf_alloc() fails on any segment that is not the initial
segment, previously allocated mbufs are not freed.
Fixes: 6db141c91e ("pcap: support jumbo frames")
Signed-off-by: Dror Birkman <dror.birkman@lightcyber.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tx function was handling a double loop to send segmented packets, it can be
done in a single one.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
PMD uses only power of two number of Work Queue Elements (aka WQE), storing
the number of elements in log2 helps to reduce the size of the container to
store it.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Blue Flame (aka BF) is a buffer allocated with a power of two value, its
size is returned by Verbs in log2.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
PMD uses only power of two number of Completion Queue Elements (aka CQE),
storing the number of elements in log2 helps to reduce the size of the
container to store it.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
PMD uses only power of two number of descriptors, storing the number of
elements in log2 helps to reduce the size of the container to store it.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Rework Work Queue Element (aka WQE) structures to fit PMD needs.
A WQE is an aggregation of 16 bytes elements known as "data segments"
(aka dseg).
The only common part is the first two elements i.e. the control one to
define the job type, and the Ethernet segment which embed offload requests
with other information, after that, it can have:
- a raw data packet,
- a data pointer to the packet itself,
- both.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
With an app using hotplug feature, when a device is unplugged without
unregistering makes the interrupt handling unstable.
Fixes: 6c53f87b34 ("nfp: add link status interrupt")
Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
81xx NIC subsystem differs in new PCI subsystem_device_id and
NICVF_CAP_CQE_RX2 capability.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Certain thunderx SoC pass has additional optional word
in Rx descriptor to hold tunneling extension info.
Based on this capability, the location where packet pointer
address stored in Rx descriptor will vary.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
thunderx pmd driver needs to support multiple SoC
variants in ThunderX family.
Remove generic pass references from driver as each SoC
can have same pass number.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
With recent gcc versions, e.g. gcc 6.1, compilation of mlx drivers with
debug enabled produces lots of errors complaining that "pedantic" is
not a warning level that can be ignored.
error: ‘-pedantic’ is not an option that controls warnings [-Werror=pragmas]
#pragma GCC diagnostic ignored "-pedantic"
^~~~~~~~~~~
These errors can be removed by changing the "-pedantic" to "-Wpedantic".
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Fixes: 771fa900b7 ("mlx5: introduce new driver for Mellanox ConnectX-4 adapters")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Missing pcap assignment may cause pcap file/interface to be opened
again, and previous one not closed.
Fixes: 1e38a7c669 ("pcap: fix storage of name and type in queues")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
simplify function rte_eth_from_pcaps_common by using interim variables.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Both fields are fields of same type of struct, one's size can't be bigger
than others.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Remove hardcoded single interface values, make it more obvious.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reorder functions to be able to remove function declarations in .c file.
Function definitions not modified.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Remove duplicated check by reorganizing the code, no functional change.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Don't carry kvlist argument into sub function and used it, use kvlist
argument in upper level of call stack.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Instead of defining numa_node variable upper level of call stack and
carry into sub function, set it where needs to be used.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
rte_eth_from_pcaps and rte_eth_from_pcaps_n_dumpers functions are very
close, updated rte_eth_from_pcaps function and reused.
No functional update.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Number of queues is defined by devargs, a check added to be sure this
number is not bigger than configured max number of queue.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
struct rx_pcaps and tx_pcaps used to point parsed devargs, but it is not
clear with current names.
Merged both into single struct and modified struct name and field names.
Functionality not changed, only struct names.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
pcap PMD is using ring PMD configuration parameters to set max number of
queues. This creates an unnecessary dependency and confusion.
Stop using configuration parameter to set max number of queues and
convert this variable into a macro within source code, to simplify
configuration file.
Default value of macro is same as ring parameter's default.
pcap pmd doesn't need to be configured in a detail to set rx and tx max
queue numbers separately, so using same macro for both queues.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Fixes: 0f6b7c7f7a ("igb: use DD bit to count RX available descriptors")
Signed-off-by: Ali Volkan Atli <volkan.atli@argela.com.tr>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
To improve performance the NIC expects for large packets to have a pointer
to a cache aligned address, old inline code could break this assumption
which hurts performance.
Fixes: 2a66cf3789 ("net/mlx5: support inline send")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Vasily Philipov <vasilyf@mellanox.com>
Rework logic of wqe_write() and wqe_write_vlan() which are pretty similar
to keep a single one.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This function was supposed to be inlined, but was not because several
functions calls it. This function should always be inline avoid
external function calls and to optimize code in data-path.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Packet rejection was routed to a polled queue. This patch route them to a
dummy queue which is not polled.
Fixes: 76f5c99e68 ("mlx5: support flow director")
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This is done to prepare support for drop queues, which are not related to
existing Rx queues and need to be managed separately.
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
memmove was moving bytes as the number of elements next to i, while it
should move the number of elements multiplied by the size of each element.
Fixes: e9086978 ("mlx5: support VLAN filtering")
Signed-off-by: Raslan Darawsheh <rdarawsheh@asaltech.com>
This capability is implemented but not reported.
Fixes: f3db948918 ("mlx5: support Rx VLAN stripping")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The return value in DPDK is negative errno on failure.
Since internal functions in mlx driver return positive
values need to negate this value when it returned to
dpdk layer.
Fixes: 76f5c99 ("mlx5: support flow director")
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
The user is allowed to call ->rx_pkt_burst() even without free
mbufs in the pool. In this scenario we'll fail allocating a rep mbuf
on the first iteration (where pkt is still NULL). This would cause us
to deref a NULL pkt (reset refcount and free).
Fix this by checking the pkt before freeing it.
Fixes: a1bdb71a32 ("net/mlx5: fix crash in Rx")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
To make the PCTYPE in x722 compatible with original PCTYPE in
flow director (FD) filters, the PCTYPE in the FD programming
descriptor needs to be translated into a different PCTYPE using
GLQF_FD_PCTYPE table.
Translation needs to be done before the FD filter is programmed.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This change enables device LRO if requested.
The current implementation of jumbo frame Rx can be used for LRO
directly without changes.
Note that since jumbo frame uses both ring0 and ring1, it cannot
be enabled in UPT (VMDirectPath) mode.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
When adding a DPDK port to ovs-vswitchd with DPDK, the vmxnet3 device
fails to activate due to mismatched magic number. This failure causes
following operations to run: start the port, stop the port,
reconfigure and re-start the port.
During reconfigure, if there is an existing memzone, driver will reuse
it. But reconfigure may request different number of Tx/Rx queues.
This results in a memzone with wrong size and potential invalid memory
access.
To fix this, free the memzone if found and reserve a new one.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Reviewed-by: Guolin Yang <gyang@vmware.com>
Reviewed-by: Daniele Di Proietto <ddiproietto@vmware.com>
Tested-by: Daniele Di Proietto <ddiproietto@vmware.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
For the vector PMD, release all mbufs from the Rx queue if no packets
are received after device start.
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
For the vector PMD, release all mbufs from the Rx queue if no packets
are received after device start.
Fixes: 11b220c649 ("ixgbe: fix release queue mbufs")
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This feature adds vhost pmd extended statistics from per port perspective
in order to meet the requirements of the applications such as OVS etc.
RX/TX xstats count the bytes without CRC. This is different from physical
NIC stats with CRC.
The statistics counters are based on RFC 2819 and RFC 2863 as follows:
rx/tx_good_packets
rx/tx_total_bytes
rx/tx_missed_pkts
rx/tx_broadcast_packets
rx/tx_multicast_packets
rx/tx_unicast_packets
rx/tx_undersize_errors
rx/tx_size_64_packets
rx/tx_size_65_to_127_packets;
rx/tx_size_128_to_255_packets;
rx/tx_size_256_to_511_packets;
rx/tx_size_512_to_1023_packets;
rx/tx_size_1024_to_1522_packets;
rx/tx_1523_to_max_packets;
rx/tx_errors
rx_fragmented_errors
rx_jabber_errors
rx_unknown_protos_packets;
No API is changed or added.
rte_eth_xstats_get_names() to retrieve what kinds of vhost xstats are
supported,
rte_eth_xstats_get() to retrieve vhost extended statistics,
rte_eth_xstats_reset() to reset vhost extended statistics.
The usage of vhost pmd xstats is the same as virtio pmd xstats.
for example, when test-pmd application is running in interactive mode
vhost pmd xstats will support the two following commands:
show port xstats all | port_id will show vhost xstats
clear port xstats all | port_id will reset vhost xstats
net/virtio pmd xstats(the function virtio_update_packet_stats) is used
as reference when implementing the feature.
Tested-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The patch moves all stats counters to a new defined struct vhost_stats
as follows, in order to manage all stats counters in a unified way and
simplify the subsequent function implementation(vhost_dev_xstats_reset).
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
In some cases when using the vHost PMD, certain vHost library functions
may still need to be accessed. One such example is the
rte_vhost_get_queue_num function which returns the number of virtqueues
reported by the guest - information which is not exposed by the PMD.
This commit introduces a new rte_eth_vhost function that returns the
'vid' associated with a given port id. This allows the PMD user to call
vHost library functions which require the 'vid' value.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Added neon based Rx vector implementation.
Selection of the new handler based neon availability at runtime.
Updated the release notes and MAINTAINERS file.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Jianbo Liu <jianbo.liu@linaro.org>
Introduced cpuflag based run-time detection to select the
SSE based simple Rx handler
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Split out SSE instruction based virtio simple Rx
implementation to a separate file
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Removed unnecessary compile time dependency on "use_simple_rxtx".
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Interestingly, clang and gcc has different prototype for _mm_prefetch().
For gcc, we have
_mm_prefetch (const void *__P, enum _mm_hint __I)
While for clang, it's
#define _mm_prefetch(a, sel) (__builtin_prefetch((void *)(a), 0, (sel)))
That's how the following error comes with clang:
error: cast from 'const void *' to 'void *' drops const qualifier
[-Werror,-Wcast-qual]
_mm_prefetch((const void *)rused, _MM_HINT_T0);
/usr/lib/llvm-3.8/bin/../lib/clang/3.8.0/include/xmmintrin.h:684:58:
note: expanded from macro '_mm_prefetch'
#define _mm_prefetch(a, sel) (__builtin_prefetch((void *)(a),
0, (sel)))
What's weird is that the build was actaully Okay before. I met it while
apply Jerin's vector support for ARM patch set: he just move this piece
of code to another file, nothing else changed.
This patch fix the issue when Jerin's patchset is applied. Thus, I think
it's still needed.
Similarly, make the same change to other _mm_prefetch users, just in case
this weird issue shows up again somehow later.
Fixes: fc3d66212f ("virtio: add vector Rx")
Fixes: c95584dc2b ("ixgbe: new vectorized functions for Rx/Tx")
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Fixes: 7092be8437 ("fm10k: add vector Rx")
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Currently, when virtio_user device fails to be started (e.g., vhost
unix socket does not exit), the init function does not return struct
rte_eth_dev (and some other structs) back to ether layer. And what's
more, it does not report the error to upper layer.
The fix is to free those structs and report error when failing to
start virtio_user devices.
Fixes: ce2eabdd43 ("net/virtio-user: add virtual device")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When virtio_user is used with VPP's native vhost user, it cannot
send/receive any packets.
The root cause is that vpp-vhost-user translates the message
VHOST_USER_SET_FEATURES as puting this device into init state,
aka, zero all related structures. However, previous code
puts this message at last in the whole initialization process,
which leads to all previous information are zeroed.
To fix this issue, we rearrange the sequence of those messages.
- step 0, send VHOST_USER_SET_VRING_CALL so that vhost allocates
virtqueue structures;
- step 1, send VHOST_USER_SET_FEATURES to confirm the features;
- step 2, send VHOST_USER_SET_MEM_TABLE to share mem regions;
- step 3, send VHOST_USER_SET_VRING_NUM, VHOST_USER_SET_VRING_BASE,
VHOST_USER_SET_VRING_ADDR, VHOST_USER_SET_VRING_KICK for each
queue;
- ...
Fixes: 37a7eb2ae8 ("net/virtio-user: add device emulation layer")
Reported-by: Zhihong Wang <zhihong.wang@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When virtio_user is used with OVS-DPDK (with mq disabled), it cannot
receive any packets. This is because no queue is enabled at all when
mq is disabled.
To fix it, we should consistently make sure the 1st queue is enabled,
which is also the behaviour QEMU takes.
Fixes: 37a7eb2ae8 ("net/virtio-user: add device emulation layer")
Reported-by: Ning Li <lining18@jd.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
We have a stats named "size_1024_1517_packets", while the code
actually counts the range "[1024, 1518]", which is obviously wrong.
The code is as follows in the function virtio_update_packet_stats.
else if (s < 1519)
stats->size_bins[6]++;
We could either fix it by correcting the "if" check in the code,
or fix it by just renaming the stats to conform to the code. The
latter solution is taken because that's what the RFC2819 suggests.
Fixes: 76d4c652e0 ("virtio: add extended stats")
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Virtio indirect descriptors are supported by the data-path
but the feature bit is never set during feature negociation.
This patch simply adds VIRTIO_RING_F_INDIRECT_DESC back to
the supported features bit mask, hence enabling the use of
indirect descriptors when the feature is negociated with the
device.
Signed-off-by: Pierre Pfister <ppfister@cisco.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Now that rte_device is available, drivers can start using its members
(numa, name) as well as link themselves into another rte_device list.
As of now no one is using this list, but can be used for moving over all
devices (pdev/vdev/Xdev) and perform bulk actions (like cleanup).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Reword commit log for extra rte_device list]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Remove the 'name' member from rte_pci_driver and move to generic
rte_driver.
Most of the PMD drivers were initially using DRIVER_REGISTER_PCI(<name>..)
as well as assigning a name to eth_driver.pci_drv.name member.
In this patch, only the original DRIVER_REGISTER_PCI(<name>..) name has
been populated into the rte_driver.name member - assignments through
eth_driver has been removed.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Rebase and expand changes to newly added files]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
There is no need to have a custom memory resource representation for
each infrastructure (PCI, ...) as it would always have the same members.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
- All devices register themselfs by calling a kind of DRIVER_REGISTER_XXX.
The PMD_REGISTER_DRIVER is not used anymore.
- PMD_VDEV type is also not being used - can be removed from all VDEVs.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
All PMD_VDEV drivers can now use rte_vdev_driver instead of the
rte_driver (which is embedded in the rte_vdev_driver).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Now that hotplug has been moved to eal, there is no reason to keep the
device type in this layer.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Simplify crypto and ethdev pci drivers init by using newly introduced
init macros and helpers.
Those drivers then don't need to register as "rte_driver"s anymore.
Exceptions:
- virtio and mlx* use RTE_INIT directly as they have custom initialization
steps.
- VDEV devices are not modified - they continue to use PMD_REGISTER_DRIVER.
Update documentation for replacing an example referring to
PMD_REGISTER_DRIVER.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Pure coding style, but it might make it easier later if we want to move
fields in rte_cryptodev_driver and eth_driver structures.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Probe and Remove are more appropriate names for PCI init and uninint
operations. This is a cosmetic change.
Only MLX* uses the PCI direct registration, bypassing PMD_* macro.
The callbacks for this too have been updated.
VDEV are left out. For them, init/uninit are more appropriate.
Suggested-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
As discussed in the past release, driver names are modified
to be more consistent, and the future driver should follow
this new convention.
Driver names consist of:
"driver category"_"driver folder name"_"optional extra name".
For example:
- Crypto null driver -> "crypto_null"
- Network IXGBE VF driver -> "net_ixgbe_vf"
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
PCI device ids moved from common header into igb driver itself.
KNI starts using pci_device_id from kni/ethtool/igb driver, this is only
for KNI ethtool support, KNI data path is not affected.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
PCI device ids moved from common header into ixgbe driver itself.
KNI starts using pci_device_id from kni/ethtool/ixgbe driver, this is
only for KNI ethtool support, KNI data path is not affected.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
The driver is incorrectly setting the RSS field in the last mbuf in
the packet chain instead of the first. Moreover, the last mbuf might
have already been freed if it only contained the Ethernet CRC.
Also, fix the call to i40e_rxd_build_fdir to store the fdir flags in
the first mbuf of the chain instead of the last.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 5a21d9715f ("i40e: report flow director matching")
Signed-off-by: Dumitru Ceara <dumitru.ceara@gmail.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
VSI structure needs to be removed from TAILQ list when releasing.
But for the child VSI it will be removed again after the structure
is freed. It will cause core dump when the DPDK i40e using as PF
host driver.
This patch fixes it to only remove child VSI from TAILQ before
send adminq command to remove it from hardware.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 440499cf53 ("net/i40e: support floating VEB")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
i40e driver was removing elements when iterating tailq lists
with TAILQ_FOREACH macro, which is not safe.
It is especially visible since the memory is zeroed on free
(commit ea0bddbd14).
Instead, TAILQ_FOREACH_SAFE macro is used when removing/freeing
these elements.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 440499cf53 ("net/i40e: support floating VEB")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The commit cb6696d220 ("drivers: update registration macro usage")
changes the name from virtio-user to virtio_user, because hyphen
cannot be used in a C symbol name. However, this commit does not
update the strings in docs and source code, which could lead to
failure to start this device as per the docs.
This patch updates related strings in the docs and source code.
Fixes: cb6696d220 ("drivers: update registration macro usage")
Reported-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Sometimes app just wants to update the RSS hash function and no RSS key
update is needed, but fm10k pmd will return EINVAL for this case.
If the rss_key is NULL, we don't need to check the rss_key_len.
Fixes: 57033cdf8f ("fm10k: add PF RSS")
Reported-by: Xueqin Lin <xueqin.lin@intel.com>
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
Rx loop inside _recv_raw_pkts_vec() ignores nb_pkts argument and always
tries to receive RTE_I40E_VPMD_RX_BURST (32) packets. This is a violation
of rte_eth_rx_burst() API and can lead to memory corruption (out-of-bounds
writes to struct rte_mbuf **rx_pkts) if nb_pkts is less than 32.
Fix this by actually using nb_pkts inside the loop.
Fixes: 9ed94e5bb0 ("i40e: add vector Rx")
Signed-off-by: Sergey Dyasly <s.dyasly@samsung.com>
Acked-by: Ilya Maximets <i.maximets@samsung.com>
Acked-by: Adam Bynes <adambynes@outlook.com>
The configure function enicpmd_dev_configure() was not paying attention
to the rxmode VLAN strip bit. Set the VLAN strip mode according to the bit.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: David Harton <dharton@cisco.com>
Tested-by: David Harton <dharton@cisco.com>
Initialize the mbuf data offset to RTE_PKTMBUF_HEADROOM as the
enic takes ownership of them. If allocated mbufs had some offset
other than RTE_PKTMBUF_HEADROOM, the application would read mbuf
data starting at the wrong place and misinterpret the packet.
Fixes: 856d7ba7ed ("net/enic: support scattered Rx")
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
drivers/net/ena/base/ena_com.c(346):
error #3656: variable "dev_node" may be used before its value is set
ENA_MEM_ALLOC_COHERENT_NODE(ena_dev->dmadev,
^
drivers/net/ena/base/ena_com.c(399):
error #3656: variable "prev_node" may be used before its value is set
ENA_MEM_ALLOC_COHERENT_NODE(ena_dev->dmadev,
^
Fixes: 3d3edc265f ("net/ena: make coherent memory allocation NUMA-aware")
Reported-by: Eoin Breen <eoin.breen@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Jan Medala <jan@semihalf.com>
The rxq/txq for the queue_release callback could be NULL, say when
rte_eth_dev_configure() fails that the queue is not setup at all.
Do a simple NULL check would fix the crash issue.
Fixes: 01ad44fd37 ("net/virtio: split Rx/Tx queue")
Reported-by: Olivier Matz <olivier.matz@6wind.com>
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The support of virtio-user changed the way the mbuf dma address is
retrieved, using a physical address in case of virtio-pci and a virtual
address in case of virtio-user.
This change introduced some possible memory corruption in packets,
replacing:
m->buf_physaddr + RTE_PKTMBUF_HEADROOM
by:
m->buf_physaddr + m->data_off (through a macro)
This patch fixes this issue, restoring the original behavior.
By the way, it also rework the macros, adding a "VIRTIO_" prefix and
API comments.
Fixes: f24f8f9fee ("net/virtio: allow virtual address to fill vring descriptors")
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When enic's interrupt handler is called indicating an error, it scans
through the receive queues (RQs) on the adapter looking for errors.
But since the inclusion of rx scatter, some of the RQs may not be in
use, and you shouldn't check them for errors.
Fixes: 856d7ba7ed ("net/enic: support scattered Rx")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
The calculation of truncated packets didn't take into account packet
errors due to the adapter not having buffers, causing both the
ipackets, and imissed counts to be wrong if such errors occurred. In
order to properly calculate the number of packets truncated, we need
to subtract the count of errors due to no buffers.
Fixes: c44d9f01ad ("net/enic: count truncated packets")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
The exported device start and stop functions where not setting the queue
states to RTE_ETH_QUEUE_STATE_STARTED and RTE_ETH_QUEUE_STATE_STOPPED.
After starting the device, the RTE queue stop function would not call
the enic queue stop function since queue was already marked as stopped.
Put queue state updates in the lower level queue start/stop functions
which are called by both device and queue start/stop functions.
Fixes: fefed3d1e6 ("enic: new driver")
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
The check that all Tx and Rx queues were set up was not
adequate when reconfiguring with a different number of
queues. Only the number of completion queues (CQs) was
being used to make the determination, but the CQ array
is shared between the underlying Rx and Tx queues.
Check that the internal Rx, Tx and CQs are all set up
before completing port configuration.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
One instance of a filter add failure was not incrementing the
the fail counter.
Fixes: 4c2c7bf41f ("net/enic: fix negative array index write")
Signed-off-by: John Daley <johndale@cisco.com>
In the burst Tx cleanup function, the reference count in mbufs
returned to the pool should to be decremented before they are
returned. Decrementing is not done by rte_mempool_put_bulk()
so it must be done separately using __rte_pktmbuf_prefree_seg().
Also when returning unsent buffers when the device is stopped
use rte_mbuf_free_seg() instead of rte_mempool_put() so that
reference counts are properly decremented.
Fixes: 36935afbc5 ("net/enic: refactor Tx mbuf recycling")
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
Signed-off-by: John Daley <johndale@cisco.com>
The enic PMD code has diverged from code that was once
shared with the enic kernel mode driver for performance
reasons. It is confusing and misleading to print the
internal version number. Remove it.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: John Daley <johndale@cisco.com>
RHEL 7.1's GCC for POWER8 reports the following error in one rte_memcpy()
macro call by mlx5:
error: array subscript is above array bounds [-Werror=array-bounds]
It appears to be a GCC bug which can be worked around by making parentheses
more explicit.
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
In multi-queue + FTAG use case, we need to turn tx_ftag_en on for all
the Tx queues.
Fixes: 7958b1310d ("fm10k: enable FTAG based forwarding")
Reported-by: Ricky Li <ricky.li@intel.com>
Signed-off-by: Xiao Wang <xiao.w.wang@intel.com>
This reverts commit 4761f57d58.
Introducing VLAN table by adding VLAN adminq command will cause NIC's
throughput drop obviously. It's a hardware issue.
With this revert, VLAN filtering can only work when promiscuous mode
is disabled.
Reverts: 4761f57d58 ("net/i40e: fix VLAN filtering in promiscuous mode")
Reported-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by : Jing Chen <jing.d.chen@intel.com>
The error is reported using test build script:
$ scripts/test-build.sh x86_64-native-linuxapp-gcc
...
drivers/net/virtio/virtio_user_ethdev.c:345:2: error:
this ‘if’ clause does not guard... [-Werror=misleading-indentation]
if (rte_kvargs_count(kvlist, VIRTIO_USER_ARG_PATH) == 1)
^~
Fixes: 404bd6bfe3 ("net/virtio-user: fix return value not checked")
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Moved defines since the driver had no such information.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reused defines from the driver and moved broadcom vendor id macro.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Moved cisco vendor id since the driver had no such information.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Moved vmware device ids macro since the driver had no such information.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reused defines from the driver.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reused defines from the driver and added a Intel vendor id macro for use by
igb later.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
igb/igbvf is left as is, waiting for kni/ethtool cleanup.
Signed-off-by: David Marchand <david.marchand@6wind.com>
The older versions of rte_eth_bond_8023ad_conf_get and
rte_eth_bond_8023ad_setup were available in the old way since 2.0 - at
least according to the map file.
But versioning in the code was set to 16.04.
That breaks compatibility checks for 2.0 on that library.
For example with the dpdk abi checker:
http://people.canonical.com/~paelzer/compat_report.html
To fix, version the old symbols on the 2.0 version as they were
initially added to the map file.
See http://people.canonical.com/~paelzer/compat_report.html
Fixes: dc40f17a ("net/bonding: allow external state machine in mode 4")
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
This is for target i686-native-linuxapp-gcc and gcc6,
Compilation error is:
In file included from
include/rte_mempool.h:77:0, from
drivers/net/virtio/virtio_rxtx_simple.c:
In function `virtio_xmit_pkts_simple':
include/rte_memcpy.h:551:2: error:
array subscript is above array bounds
rte_mov16((uint8_t *)dst + 1 * 16, (const uint8_t *)src + 1 * 16);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Call stack is as following:
virtio_xmit_pkts_simple
virtio_xmit_cleanup
rte_mempool_put_bulk
rte_mempool_generic_put
__mempool_generic_put
rte_memcpy
The array used as source buffer in virtio_xmit_cleanup (free) is a
pointer array with 32 elements, in 32bit this makes 128 bytes.
in rte_memcpy() implementation, there a code piece as following:
if (size > 256) {
rte_move128(...);
rte_move128(...); <--- [1]
....
}
The compiler traces the array all through the call stack and knows the
size of array is 128 and generates a warning on above [1] which tries to
access beyond byte 128.
But unfortunately it ignores the "(size > 256)" check.
Giving a hint to compiler that variable "size" is related to the size of
the source buffer fixes compiler warning.
Fixes: 863bfb4744 ("mempool: optimize copy in cache")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Fixes a bug where rte_eth_vhost_get_queue_event would not return enabled
queues after a guest application restart.
Fixes: ee584e9710 ("vhost: add driver on top of the library")
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
There is a logic bug in this code, that could lead to null pointer
dereference when cvq is NULL. Fix this problem by changing logic
&& to logic ||.
>> CID 127480: Null pointer dereferences (FORWARD_NULL)
>> Dereferencing null pointer "cvq".
if (!cvq && !cvq->vq) {
...
}
Coverity issue: 127480
Fixes: 01ad44fd37 ("net/virtio: split Rx/Tx queue")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When use strcpy() to copy string with length exceeding the last
parameter of strcpy(), it may lead to the destination string
unterminated.
We replaced strncpy with snprintf to make sure it's NULL terminated.
Coverity issue: 127476
Fixes: ce2eabdd43 ("net/virtio-user: add virtual device")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The return value by rte_kvargs_parse is not free(d), which leads
to memory leak.
Coverity issue: 127482
Fixes: ce2eabdd43 ("net/virtio-user: add virtual device")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When parsing /proc/self/maps to get hugepage information, the string
was being copied with strcpy(), which could, theoretically but in fact
not possiblly, overflow the destination buffer. Anyway, to avoid the
false alarm, we replaced strncpy with snprintf for safely copying the
strings.
Coverity issue: 127484
Fixes: 6a84c37e39 ("net/virtio-user: add vhost-user adapter layer")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
When return values of function calls are not checked, Coverity will
report errors like:
if (rte_kvargs_count(kvlist, VIRTIO_USER_ARG_PATH) == 1)
>>> CID 127477: (CHECKED_RETURN)
>>> Calling "rte_kvargs_process" without checking return value
(as is done elsewhere 25 out of 30 times).
rte_kvargs_process(kvlist, VIRTIO_USER_ARG_PATH,
&get_string_arg, &path);
Coverity issue: 127477, 127478
Fixes: ce2eabdd43 ("net/virtio-user: add virtual device")
Fixes: 6a84c37e39 ("net/virtio-user: add vhost-user adapter layer")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
On some older systems, such as SUSE 11, the compiling error shows
as:
.../dpdk/drivers/net/virtio/virtio_user/virtio_user_dev.c:67:22:
error: ‘O_CLOEXEC’ undeclared (first use in this function)
The fix is to use EFD_CLOEXEC, which is defined in sys/eventfd.h,
instead of O_CLOEXEC which needs _GNU_SOURCE defined on some old
systems.
Fixes: 37a7eb2ae8 ("net/virtio-user: add device emulation layer")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Avoid submitting doorbell when:
* no packets have been submitted to TX
* no free resources have been submitted while RX
Sending doorbell without actual work to be performed by device
violates ENA specification and can lead to unpredictable behavior.
Fixes: 1173fca25a ("ena: add polling-mode driver")
Signed-off-by: Alexander Matushevsky <matua@amazon.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
enic_set_mac_address() meant to remove the old MAC address before
setting the new one, but accidentally tried removing the new MAC
address before setting the new MAC address.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
enic_disable() removed the MAC address when a port was shut down but
enic_enable() didn't add the MAC address back when the port was
started again. Move where we set the MAC address for the adapter from
enic_setup_finish() to a enic_enable() so that port restarting works
properly.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
This patch adds support for extended statistics for BNX2X PMD.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds support for extended statistics for QEDE PMD.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fixed issue could occur when Mbuf starvation happens in a middle of
reception of a segmented packet. In such a situation, the PMD has to
release all segments of that packet. The end condition was wrong
causing it to free an Mbuf still handled by the NIC.
Fixes: 9964b965ad ("net/mlx5: re-add Rx scatter support")
Reported-by: Yongseok Koh <yskoh@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
In mlx5 rx function, the packet_type and ol_flags mbuf fields are not
properly initialized when no rx offload feature is enabled (checksum, l2
tun checksum, vlan_strip, crc). Thus, these fields can have a value
different of 0 depending on their value when the mbuf was freed.
This can result in an incorrect application behavior if invalid
ol_flags/ptype are set, or memory corruptions if IND_ATTACHED_MBUF is
set in ol_flags.
Fixes: 081f7eae24 ("mlx5: process offload flags only when requested")
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The enic PMD was using the same variables in the enic structure to
track two different things. Initially rq_count, wq_count, cq_count,
and intr_count were set to the values obtained from the VIC adapters
as the maximum resources allocated on the VIC, then in
enic_set_vnic_res(), they were set to the counts of resources actually
used, discarding the initial values. The checks in enic_set_vnic_res()
were technically incorrect if it is called more than once on a port,
which happens when using bonding, but were harmless in practice as the
checks couldn't fail on the second call.
The enic rx-scatter patch misunderstood the subtleties of
enic_set_vnic_res(), and naively added a multiply by two to the
rq_count check. This resulted in the rq_count check failing when
enic_set_vnic_res() was called a second time, ie when using bonding.
This patch adds new variables to the enic structure to track the
maximum resources the VIC is configured to provide so that the
information isn't later lost and calls to enic_set_vnic_res() do
the expected thing.
Fixes: 856d7ba7ed ("net/enic: support scattered Rx")
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
When calling i40e_flowtype_to_pctype in i40e_get_hash_filter_global_config
and i40e_set_hash_filter_global_config, function i40e_flowtype_to_pctype
will be possibly make an out-of-bounds access, because size of the array
is 15. So check the flow type is valid before calling
i40e_flowtype_to_pctype.
In the process fix other occurances of the same problem
Coverity issue: 37793, 37794
Fixes: 782c8c92f1 ("i40e: add hash configuration")
Fixes: f2b2e2354b ("i40e: split function for hash and flow director input")
Fixes: 98f0557076 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Null-checking vsi suggests that it may be null, but it
has been dereferenced before null-checking. So move the
check to before the assignment statement using the pointer.
Coverity issue: 119265, 119266
Fixes: d0a349409b ("i40e: support AQ based RSS config")
Fixes: 647d1eaf75 ("i40evf: support AQ based RSS config")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The condition, "(pf->flags | I40E_FLAG_VMDQ)" will always be true,
regardless of the value of the flags operand, because I40E_FLAG_VMDQ
is 4ULL - meaning at least one bit will always be set in the result.
That will cause log error when VMDq is disabled.
Since the original intent behind the condition is to check if VMDq
is enabled, fix the code by changing "|" to "&".
Coverity issue: 13219, 13221
Fixes: 4805ed59e9 ("i40e: enhance mac address operations")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Currently we are wrongly setting HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST
flag in bnxt_hwrm_cfa_l2_set_rx_mask() which is preventing promiscuous
and multicast promiscuous settings from working correctly.
This patch fixes it.
Fixes: 244bc98b0d ("net/bnxt: set L2 Rx mask")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Memory zones should be freed using the proper memzone_free function not
rte_free which is for malloc calls.
After allocating memzone it's required to zeroize memory in it, so do so
before storing the handle for later freeing.
Fixes: 9ba7981ec9 ("ena: add communication layer for DPDK")
Signed-off-by: Alexander Matushevsky <matua@amazon.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
While allocating (coherent) memory, get information about calling node Id
and pass that as parameter when reserving a memzone.
Signed-off-by: Alexander Matushevsky <matua@amazon.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
Depending on HW revision readless communcation between host and device
may be unavailable. In that case prevent PMD from setting up readless
communication mechanism.
"readless" refers to ability to read ENA registers without actually
issuing read request from host (x86). Instead, host programs 2 registers
on the device that triggers a DMA from device to host and reports a
register value. However, this functionality is not going to be available
in all types of devices. The decision if this mode is supported or not,
is taken from revision_id in pci configuration space.
Signed-off-by: Alexander Matushevsky <matua@amazon.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
Increase maintenance and debug potentiality with dedicated areas of memory
where additional information can be stored by the ENA device.
Signed-off-by: Alexander Matushevsky <matua@amazon.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
