The point of r345008 was to reset the Command Reference Number (CRN)
in some situations where a device stayed in the topology, but had
changed somehow.
This can include moving from a switch connection to a direct
connection or vice versa, or a device that temporarily goes away
and comes back. (e.g. moving to a different switch port)
There were a couple of bugs in that change:
- We were reporting that a device had not changed whenever the
Establish Image Pair bit was not set. That is not quite correct.
Instead, if the Establish Image Pair bit stays the same (set or
not), the device hasn't changed in that way.
- We weren't setting PRLI Word0 in the port database when a new
device arrived, so comparisons with the old value for the
Establish Image Pair bit weren't really possible. So, make sure
PRLI Word0 is set in the port database for new devices.
- We were resetting the CRN whenever the Establish Image Pair bit
was set for a device, even when the device had stayed the same
and the value of the bit hadn't changed. Now, only reset the
CRN for devices that have changed, not devices that sayed the
same.
The result of all of this was that if we had a single FC device on
an FC port and it went away and came back, we would wind up
correctly resetting the CRN.
But, if we had multiple devices connected via a switch, and there
was any change in one or more of those devices, all of the devices
that stayed the same would also have their CRN values reset.
The result, from a user standpoint, is that the tape drives, etc.
would all start to time out commands and the initiator would send
aborts.
sys/dev/isp/isp.c:
In isp_pdb_add_update(), look at whether the Establish
Image Pair bit has changed as part of the check to
determine whether a device is still the same. This was
causing erroneous change notifications. Also, when
creating a new port database entry, initialize the
PRLI Word 0 values.
sys/dev/isp/isp_freebsd.c:
In isp_async(), in the changed/stayed case, instead of
looking at the Establish Image Pair bit to determine
whether to reset the CRN, look at the command value.
(Changed vs. Stayed.) Only reset the CRN for devices
that have changed.
Sponsored by: Spectra Logic
MFC after: 3 days
It is possible for the kernel mapping to be created with superpage by
directly installing pde using pmap_enter_2mpage() without filling the
corresponding page table page. This can happen e.g. if the range is
already backed by reservation and vm_fault_soft_fast() conditions are
satisfied, which was observed on the pipe_map.
In this case, demotion must fill the page obtained from the pmap
radix, same as if the page is newly allocated. Use PG_PROMOTED bit as
an indicator that the page is valid, instead of the wire count of the
page table page.
Since the PG_PROMOTED bit is set on pde when we leave TLB entries for
4k pages around, which in particular means that the ptes were filled,
it provides more correct indicator. Note that pmap_protect_pde()
clears PG_PROMOTED, which handles the case when protection was changed
on the superpage without adjusting ptes.
Reported by: pho
In collaboration with: alc
Tested by: alc, pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20380
It doesn't make sense to limit to -j12 anymore, build scalability
is better than it used to be. Fold the hint into the description
of the universe target.
Reviewed by: imp
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D20342
Allow support of other VCSes. Note that two other nanobsd files already
had a similar case, excluding .git and .hg in addition to CVS and .svn.
Sponsored by: The FreeBSD Foundation
since r286195.
Do not forget results of route lookup and initialize rt and ifp pointers.
PR: 238098
Submitted by: Masse Nicolas <nicolas.masse at stormshield eu>
MFC after: 1 week
command to simplify firewall reloading.
The `missing` option suppresses EEXIST error code, but does check that
existing table has the same parameters as new one. The `or-flush` option
implies `missing` option and additionally does flush for table if it
is already exist.
Submitted by: lev
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18339
That made, for example, gpioc -l output quite hard to read and parse.
Also, fix formatting of a nearby statement with too long lines.
MFC after: 2 weeks
For older versions of zlib, dummy was a workaround for compilers that do not
handle opaque type definition well; on FreeBSD, it's representing a value
that is not really useful for monitoring purposes, and the field would be gone
in newer zlib versions.
PR: 229763
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
Differential Revision: https://reviews.freebsd.org/D20222
Fixed by r348215, bectl ujail first attempts the trivial fetch of a jid by
passing the first argument to 'ujail' to jail_getid(3) in case a jid/name
have been passed in instead of a BE name. For numerically named BEs, this
was doing the wrong thing: instead of failing to locate the jid specified
and falling back to mountpath search, jail_getid(3) would return the input
as-is.
While here, I've fixed bectl_jail_cleanup which still used a hard-coded pool
name that was overlooked w.r.t. other work that was in-flight around the
same time.
MFC after: 3 days
Currently, if jail_getid(3) is passed in a numeric string, it assumes that
this is a jid string and passes it back converted to an int without checking
that it's a valid/existing jid. This breaks consumers that might use
jail_getid(3) to see if it can trivially grab a jid from a name if that name
happens to be numeric but not actually the name/jid of the jail. Instead of
returning -1 for the jail not existing, it'll return the int version of the
input and the consumer will not fallback to trying other methods.
Pass the numeric input to jail_get(2) as the jid for validation, rather than
the name. This works well- the kernel enforces that jid=name if name is
numeric, so doing the safe thing and checking numeric input as a jid will
still DTRT based on the description of jail_getid.
Reported by: Wes Maag
Reviewed by: jamie, Wes Maag
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D20388
- Add a write_mem counterpart to read_mem to handle writes to MMIO.
- Add support for the GDB 'M' packet to write bytes to the guest's
memory. For MMIO writes, attempt to batch writes up into words.
This is imprecise, but if you write a single 2 or 4-byte aligned
word, it should be treated as a single MMIO write operation.
- While here, tidy up the parsing of the 'm' command used for reading
memory to match 'M'.
Reviewed by: markj, Scott Phillips <d.scott.phillips@intel.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20307
- Triple DES has been formally deprecated in Kerberos (RFC 8429)
and is soon to be deprecated in IPsec (RFC 8221).
- Blowfish is deprecated. FreeBSD doesn't support its successor
(Twofish).
- MD5 is generally considered a weak digest that has known attacks.
geli refuses to create new volumes using these algorithms via 'geli
init'. It also warns when attaching to existing volumes or creating
temporary volumes via 'geli onetime' . The plan is to fully remove
support for these algorithms in FreeBSD 13.
Note that none of these algorithms have ever been the default
algorithm used by geli(8). Users would have had to explicitly select
these algorithms when creating volumes in the past.
Reviewed by: cem, delphij
MFC after: 3 days
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20344
All of these algorithms are either explicitly marked MUST NOT, or they
are implicitly MUST NOTs by virtue of not being included in IETF's
list of protocols at all despite having assignments from IANA.
Specifically, this adds warnings for the following ciphers:
- des-cbc
- blowfish-cbc
- cast128-cbc
- des-deriv
- des-32iv
- camellia-cbc
Warnings for the following authentication algorithms are also added:
- hmac-md5
- keyed-md5
- keyed-sha1
- hmac-ripemd160
Reviewed by: cem, gnn
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20340
Pull the responsibility for zeroing events, which is general to any
conceivable implementation of a random device algorithm, out of the
algorithm-specific Fortuna code and into the callers. Most callers
indirect through random_fortuna_process_event(), so add the logic there.
Most callers already explicitly bzeroed the events they provided, so the
logic in Fortuna was mostly redundant.
Add one missing bzero in randomdev_accumulate(). Also, remove a redundant
bzero in the same function -- randomdev_hash_finish() is obliged to bzero
the hash state.
Reviewed by: delphij
Approved by: secteam(delphij)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20318
Add Chacha20 mode to Encrypted Kernel Crash Dumps.
Chacha20 does not require messages to be multiples of block size, so it is
valid to use the cipher on non-block-sized messages without the explicit
padding AES-CBC would require. Therefore, allow use with simultaneous dump
compression. (Continue to disallow use of AES-CBC EKCD with compression.)
dumpon(8) gains a -C cipher flag to select between chacha and aes-cbc.
It defaults to chacha if no -C option is provided. The man page documents this
behavior.
Relnotes: sure
Sponsored by: Dell EMC Isilon
This takes the SPCR code currently in uart_cpu_arm64.c, moves it into
a new uart_cpu_acpi.c (with some associated refactoring), and uses it
from both arm64 and x86.
An SPCR serial port address AccessWidth field value of 0 ("reserved")
is now treated as 1 ("byte access") in order to work around a buggy
SPCR table on Amazon EC2 i3.metal instances.
Reviewed by: manu, Greg V
MFC after: 3 days
Sponsored by: https://www.patreon.com/cperciva
Differential Revision: https://reviews.freebsd.org/D20357
This adds some new commands to loader :
- pnpmatch
This takes a pnpinfo string as argument and tries to find a kernel module
associated with it. -v and -d option are available and are the same as in
devmatch (v is verbose, d dumps the hints).
- pnpload
This takes a pnpinfo string as argument and tries to load a kernel module
associated with it.
- pnpautoload
This will attempt to load every kernel module for each buses. Each buses are
probed, the probe function will generate pnpinfo string and load kernel module
associated with it if it exists.
Only simplebus for FDT system is implemented for now.
Since we need the dtb and overlays to be applied before searching the tree
fdt_devmatch_next will load and apply the dtb + overlays.
All the pnp parsing code comes from devmatch and is the same at 99%.
Reviewed by: imp, kevans
Differential Revision: https://reviews.freebsd.org/D19498
Use the .PATH mechanism instead so keep installing them from lib/libc/gen
While here revert 347961 and 347893 which are no longer needed
Discussed with: manu
Tested by: manu
ok manu@
Some clocks used the NM type but this clock is for the ones with the
formula "clk = clkin / n / m" and not "clk = clkin * n / m"
Use the new frac clock for them.
Add a clock driver for clock that can either be used in integer mode
with one N factor and one M divider or in fractional mode where the
output frequency is chosen between two predifined output.
newvers.sh has supported a variable setting only mode, use that in
preference to grep to future proof this script from changes there.
Differential Revision: https://reviews.freebsd.org/D19849
Rather than the tedious and error-prone grep of sys/conf/newvers.sh,
use the new -v arg to dig out the data that's desired.
Differential Revision: https://reviews.freebsd.org/D19849
Add -v to print TYPE REVISION BRANCH RELEASE VERSION RELDATE variables
Add -V var to print var's value
Both of these in ${var}="${val}" format suitable for
eval $(sh newvers.sh -v)
in shell scripts / makefiles.
Add -c to print the copyright / license comment text only.
Document these, and remove soon-to-be obsolete comment.
Minor code motion as well bunded here to put functions after
VARS_ONLY and command line argument parsing.
Differential Revision: https://reviews.freebsd.org/D19849
Due to how the linker.hints file is laid out, we'll associate the pnp
info with the wrong module if the module declaration comes after the
pnp info. Until that limiation is removed, we need to have this
ordering. Ideally, we'd also enforce the ordering somehow, but I've
come up with no way to do that yet...
Pnpinfo is bus-specific and requires the bus name. The FDTCOMPAT_PNP_INFO()
macro makes it easier to define new FDT-based pnpinfo for busses other than
simplebus.
Differential Revision: https://reviews.freebsd.org/D20382
See usage for the command line structure. Man page will come shortly.
Reviewed by: jilles, tmunro
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20258
Many i2c slave drivers are in modules that can be unloaded. If they detach
while IO is in progress the bus would be hung forever. Conversely,
lower-layer drivers (iicbus and the hardware driver) also live in modules
and other kinds of bad things happen if they get detached while IO is in
progress. Because device_busy() propagates up to parents, marking the slave
device busy while it owns the bus solves both kinds of problems that come
with detaching i2c devices while IO is in progress.
