- The Tx power (diff) values should be signed
- Fix an off by one error when reading Tx power (diff) values
Reviewed by: avos, adrian
Differential Revision: https://reviews.freebsd.org/D8571
Because link state change events aren't enabled until the end of init(),
the initial link up event could be missed. Check the current media status
immediately after enabling the default completion ring interrupt.
Approved by: sbruno
MFC after: 12 days
Sponsored by: Broadcom Limited
This makes the file name and the variable naming in the file consistent.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
We'd better add this dependency explicitly, though usually the pci
driver is built into the kernel by default.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
This fixes an error handling detail in iwm_nvm_read_chunk(), where an
error response from the firmware for an NVM read shouldn't be fatal if
the offset was non-zero.
Approved by: adrian (mentor)
Obtained from: DragonFlyBSD git 250a1c33fca1725121fe499f9cebc90267d209f9
Differential Revision: https://reviews.freebsd.org/D8542
Do not assume that all uart drivers use uart_softc structure as is.
Some do a sensible thing and do declare their uart class and driver
properly and arrive into uart_bus_attach with suitably sized softc.
Submitted by: kan
Sponsored by: DARPA, AFRL
The gpiobus driver is attached explicitly and generally should be
at the same pass as its parent. Making it use BUS_PAS_BUS ensures
that it attaches immediately after parent adds it (assuming the
parent itself attached at BUS_PAS_BUS and above).
Submitted by: kan
Sponsored by: DARPA, AFRL
This is Infineon ADM6996FC/M/MX driver code on etherswitch framework.
Support PORT and DOT1Q VLAN.
This code suppose ADM6996FC SDC/SDIO connect to SOC network interface
MDC/MDIO.
This code tested on Netgear WGR614Cv7.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: adrian, mizhka
Approved by: adrian(mentor)
Differential Revision: https://reviews.freebsd.org/D8495
The feature enables us to pass through physical PCIe devices to FreeBSD VM
running on Hyper-V (Windows Server 2016) to get near-native performance with
low CPU utilization.
The patch implements a PCI bridge driver to support the feature:
1) The pcib driver talks to the host to discover device(s) and presents
the device(s) to FreeBSD's pci driver via PCI configuration space (note:
to access the configuration space, we don't use the standard I/O port
0xCF8/CFC method; instead, we use an MMIO-based method supplied by Hyper-V,
which is very similar to the 0xCF8/CFC method).
2) The pcib driver allocates resources for the device(s) and initialize
the related BARs, when the device driver's attach method is invoked;
3) The pcib driver talks to the host to create MSI/MSI-X interrupt
remapping between the guest and the host;
4) The pcib driver supports device hot add/remove.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8332
The new methods will be used by the coming pcib driver.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8409
vcpu_id is host's representation of guest CPU.
We get the mapping between vcpu_id and FreeBSD kernel's cpu id when VMBus
driver is loaded. Later, when a driver, like the coming pcib driver, talks
to the host and needs to refer to a guest CPU, the driver must use the
vcpu_id.
Reviewed by: jhb, sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8410
Drop the tracking down to the pmap layer, with optimizations to only track
necessary pages. This should give a (slight) performance improvement, as well
as a stability improvement, as the tracking is already mostly handled by the
pmap layer.
Summary:
This implements part of the gpio-poweroff and gpio-restart device tree
bindings. Optional properties are not handled currently. It also currently
only supports level-triggered reset.
Reviewed By: gonzo
Differential Revision: https://reviews.freebsd.org/D8521
If MII1 interface is disabled, then enable phy4/mac4.
Submitted by: Hiroki Mori <yamori813@yahoo.co.jp>
Reviewed by: mizhka, adrian
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6832
This commit is part of D6920 review. One of macro had wrong prefix:
BMCA => BCMA
Reviewed by: landonf, adrian (mentor)
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6920
To enable event sourcing from kbdmux(4) kern.evdev.rcpt_mask value
should have bit 1 set (this is default)
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8437
VSS stands for "Volume Shadow Copy Service". Unlike virtual machine
snapshot, it only takes snapshot for the virtual disks, so both
filesystem and applications have to aware of it, and cooperate the
whole VSS process.
This driver exposes two device files to the userland:
/dev/hv_fsvss_dev
Normally userland programs should _not_ mess with this device file.
It is currently used by the hv_vss_daemon(8), which freezes and
thaws the filesystem. NOTE: currently only UFS is supported, if
the system mounts _any_ other filesystems, the hv_vss_daemon(8)
will veto the VSS process.
If hv_vss_daemon(8) was disabled, then this device file must be
opened, and proper ioctls must be issued to keep the VSS working.
/dev/hv_appvss_dev
Userland application can opened this device file to receive the
VSS freeze notification, hold the VSS for a while (mainly to flush
application data to filesystem), release the VSS process, and
receive the VSS thaw notification i.e. applications can run again.
The VSS will still work, even if this device file is not opened.
However, only filesystem consistency is promised, if this device
file is not opened or is not operated properly.
hv_vss_daemon(8) is started by devd(8) by default. It can be disabled
by editting /etc/devd/hyperv.conf.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reviewed by: kib, mckusick
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8224
Do not overwrite the contents of the WUC register, add E1000_WUC_PME_EN
to the register contents, leaving the default contents intact.
PR: 208343
Submitted by: Kaho Toshikazu <kaho@elam.kais.kyoto-u.ac.jp>
Reviewed by: jeffrey piper <jeffrey.e.pieper@intel.com>
Approved by: erj@
MFC after: 2 weeks
Linux has a slightly different device tree definition for DPAA than originally
done in the FreeBSD driver. This changes the driver to be mostly compatible
with the Linux device tree definitions. Currently the differences are:
bman-portals: compatible = "fsl,bman-portals" (Linux is "simple-bus")
qman-portals: compatible = "fsl,qman-portals" (Linux is "simple-bus")
fman: compatible = "fsl,fman" (Linux is "simple-bus")
The Linux device tree doesn't specify anything for rgmii in the mdio. This
change still requires the device tree to specify the phy-handle, and doesn't yet
support tbi.
before calling ieee80211_ifattach() so the taskqueue hasn't been
initialized. Don't try to drain it, we'll panic.
Looks like this issue was introduced in r303326.
Reviewed by: avos, sbruno, adrian
Differential Revision: https://reviews.freebsd.org/D8499
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
- Attach only to WMI devices that provide supported GUIDs. HP Spectre x360
has two WMI devices, only one of which provides the GUIDs.
- Pass proper device to ACPI_WMI_REMOVE_EVENT_HANDLER() on detach.
- Improve error WMI handling separating status and data paths. This allows
to hide sysctls not supported by specific hardware/BIOS.
- Improve CMI block parser to make it work on HP Spectre x360 laptop.
- In verbose mode log all unknown events to help futher improvements.
In the case where a hardware error is detected during
ioat_process_events, hardware may advance (by one descriptor, probably)
and a subsequent ioat_process_events may race the intended ioat_reset_hw
followup. In that case, the second process_events would observe a
completion update that does not match the software "last_seen" status,
and attempt to successfully complete already-failed descriptors.
Guard against this race with the resetting_cleanup flag.
Reviewed by: bdrewery, markj
Sponsored by: Dell EMC Isilon
Newer CPUs (SkyLakes) have updates of 100K size, which is bigger than
current limit 32K. Increase it to 4M but leave the check around to
prevent kernel memory allocator abuse. Some time ago, the memory for
update was allocated by contigmalloc(9), and it was reasonable to be
conservative as much as possible. Since all uses of contigmalloc(9)
appear to be either misunderstanding or too cautious, and were
removed, provide more slack than strictly neccessary.
Submitted by: Oliver Pinter
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D8486
The constant was set to the correct value in r308242.
While there, fix iicsmb_bread() to not use a value of an out parameter
'count'.
MFC after: 3 weeks
X-MFC after: r308242
The hardware does not implement SMBus Process Call command, so remove
ifdef-ed out code from intsmb_pcall. The code used exactly the same
start sequence as for Write Word command.
intsmb_bread code used to access an in value of the count parameter,
but that parameter is supposed to be an out only parameter.
For example, smb(4) does not initialize it before calling smbus_bread.
MFC after: 3 weeks
Previously, those ioctls were defined as 'in' only, so rdata.byte and
rdata.word were never updated in the userland. The read data went only
to rbuf if it was provided. Thus, consumers were forced to always use it.
Now the ioctls are marked as in-out.
Compatibility handlers are provided for old ioctls.
PR: 213481
Reported by: Lewis Donzis <lew@perftech.com>
MFC after: 2 weeks
Relnotes: maybe
Differential Revision: https://reviews.freebsd.org/D8430
I see the fllowing panic on AMD when exiting pmcstat:
panic: [pmc,1473] pp_pmcval outside of expected range cpu=2 ri=17
pp_pmcval=fffffffffa529f5b pm_reloadcount=10000
It seems that at least on AMD a performance counter keeps counting after
overflowing. When pmcstat exits it sets counters that it used to
PMC_STATE_DELETED and waits until their use count goes to zero.
amd_intr() wouldn't reload a counter in that state and, thus, a counter
would be allowed to overflow. That means that the counter's value would
be allowed to go outside the expected range.
MFC after: 2 weeks
The expected deviation should not be more than 1Hz per second. The USB
v2.0 specification also mandates this requirement. Refer to chapter
5.12.4.2 about feedback.
PR: 208791
MFC after: 3 days
address, but the associated PF is giving the VF an all zeros MAC address
when one is not administratively assigned. The driver should check for
this case and generate a random address, similar to how the linux igbvf
driver does.
Submitted by: skoumjian@juniper.net (Scott Koumjian)
MFH: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8399
- Split driver in two parts: FDT and non-FDT
- Instead of reattach gpioled nodes to GPIO bus use
gpio_pin_get_by_ofw_idx and add ofwbus and simplebus as parrent buses
Reviewed by: loos
Differential Revision: https://reviews.freebsd.org/D8233
The firmware/hardware does not generate additional completion
events unless we post new buffers. Use a timer to try to post
more buffers in case we are temporarily out of mbufs. Else
the receive schedule completely stops.
Sponsored by: Mellanox Technologies
MFC after: 1 week
NOTE: some multi-vap configurations (e.g., STA+IBSS) are not stable;
that will be fixed later.
Tested with:
- RTL8188CE, STA + AP mode;
- RTL8188CE, IBSS mode;
- RTL8188CUS, IBSS mode;
- RTL8188EU, IBSS mode.
Relnotes: yes
rtwn_usb: drain USB transfers during device shutdown; this fixes possible
panic with 'options IEEE80211_SUPPORT_SUPERG' during device detach.
Tested with RTL8188CE, STA mode.
Do not try to clear stale Tx descriptor entries when there are some
running vaps; just free node references - rtwn_pci_tx_done() will free
mbufs without creating holes in the Tx descriptor space.
Also, reset only 2 first entries in the beacon ring - other will not be
used anyway.
Tested with RTL8188CE, STA + STA mode.
- Correctly refresh Rx filter when AP (IBSS) vap is created after STA vap.
- Block any RCR updates during TSF correction (IBSS mode).
- Set CBSSID* bits during vap creation, not when it was started / stopped.
- Cache current state to prevent unnecessary register reads.
Tested with RTL8188CE, STA + AP mode.
adapter to work around bugs in TSO handling at this speed.
em_init_locked is called during first boot of the adapter and will
see that link_speed is unitialized, effectively turning off tso for
all cards at all speeds, which I believe was *not* the intent.
Move the handling of TSO deactivation to the link handler where we can
more effectively make the decision about what to do. In addition,
completely purge the TSO capabilities instead of disabling just CSUM_TSO.
Thanks to jhb for explanation of the hw capabilites api.
Thanks to royger and cognet for testing the 100Mbit failure case to
ensure that their adapters do indeed still work.
MFC after: 1 week
Sponsored by: Limelight Networks
Bay Trail has three banks of GPIOs exposed to userland as /dev/gpiocN,
where N is 1, 2, and 3. Pins in each bank are pre-named to match names
on boards schematics: GPIO_S0_SCnn, GPIO_S0_NCnn, and GPIO_S5_nn.
Controller supports edge-triggered and level-triggered interrupts but
current version of the driver does not have interrupts support
This is a long time coming. The general pieces have been floating around
in a local repo since circa 2012 when I dropped the net80211 support
into the tree.
This allows the per-chain RSSI and NF to show up in 'ifconfig wlanX list sta'.
I haven't yet implemented the EVM hookups so that'll show up; that'll come
later.
Thanks to Susie Hellings <susie@susie.id.au> who did the original work
on this a looong time ago for a company we both worked at.
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
To enable event sourcing from atkbd kern.evdev.rcpt_mask value
should have bit 3 set.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8381
The device doesn't accurately update the CHANCMP address with the device state
when the device is suspended or halted. So, read the CHANSTS register to check
for those states.
We still need to read the CHANCMP address for the last completed descriptor.
Sponsored by: Dell EMC Isilon
that are apparently misconfigured by the manufacturer and cause the mapping
logic to fail. The fallback allows drive numbers to be assigned based on the
PHY number that they're attached to. Add sysctls and tunables to overrid
this new behavior, but they should be considered only necessary for debugging.
Reviewed by: imp, smh
Obtained from: Netflix
MFC after: 3 days
Sponsored by: D8403
While I'm here, move message status codes to hv_utilreg.h, since they
will be used by the upcoming VSS stuffs.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8391
With guest trackpoint present trackpoint probing switched synaptics
device to absolute mode with different protocol instead of keeping it
in relative mode.
PR: 213757
Submitted by: Vladimir Kondratyev <wulf@cicgroup.ru>
MFC after: 1 week
Summary:
i.MX5 and PowerPC use a very similar eSDHC controller, which is also
similar to the uSDHC controller used by i.MX6. The imx_sdhci driver works
almost completely with PowerPC, with some minor tweaks.
There is one caveat with this: reset currently does not work on PowerPC, so has
been #ifdef'd out until this can be tracked down and fixed. If resets are done
the controller will timeout all data transactions. Without a reset, it appears
to work just fine.
This is part 3, following up r308186 and r308187.
Test Plan:
This has been tested on a PowerPC QorIQ P1022 board. It has not been
tested on i.MX, but no regressions are expected.
Reviewed By: imp
Differential Revision: https://reviews.freebsd.org/D8407
Some controllers (namely Freescale's eSDHC, tested) will continue to assert
the card removed or card insert interrupts even after being handled. To work
around this, disable watching the interrupt that just occurred until the
opposite interrupt is triggered.
Linux has a similar change in its driver to address the same problem.
* Starting a scan from wpa_supplicant or via ifconfig while associated,
should no longer cause firmware panics or abort early.
Tested:
* AC7260, STA mode
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8412
* SYNC_RESP_STRUCT and SYNC_RESP_PTR originate from the OpenBSD version of
iwm, and they weren't serving any real purpose in the FreeBSD port.
* We just do a single bus_dmamap_sync for syncing the complete received frame,
instead of explicitly bus_dmamap_sync-ing subranges of the frame like in
the OpenBSD iwm code.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7939
This allows us to make strong assertions about descriptor address
validity. Additionally, future generations of the ioat(4) hardware will
require contiguous descriptors.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
This paves the way for a contiguous descriptor array.
A contiguous descriptor array has the benefit that we can make strong
assertions about whether an address is a valid descriptor or not. The
other benefit is that future generations of I/OAT hardware will require
a contiguous descriptor array anyway. The downside is that after system
boot, big chunks of contiguous memory is much harder to find. So
dynamic scaling after boot is basically impossible.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
And put them under HN_IFSTART_SUPPORT, which is by default on until
we whack the if_start related bits from base system.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8392
Upstream the BUF_TRACKING and FULL_BUF_TRACKING buffer debugging code.
This can be handy in tracking down what code touched hung bios and bufs
last. The full history is especially useful, but adds enough bloat that
it shouldn't be enabled in release builds.
Function names (or arbitrary string constants) are tracked in a
fixed-size ring in bufs. Bios gain a pointer to the upper buf for
tracking. SCSI CCBs gain a pointer to the upper bio for tracking.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8366
A grant-table user-space device will allow user-space applications to map
and share grants (Xen way to share memory) among Xen domains. This grant
table user-space device has been tested with the QEMU Qdisk Xen backed.
Submitted by: jaggi
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D7293
- Move the SYSINIT to DRIVER/SECOND, i.e. after the vm_guest becomes
determistic.
- Minor style changes.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8370
Mainly because the host side only set TCPCS and IPCS even for
UDP datagrams.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8369
And use large default temporary channel packer buffer; we really
don't want it to be expanded at run time.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8367
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
It is possible that wrmsr in amd_stop_pmc() causes an overflow in a counter
that it disables. In that case a non-maskable interrupt is generated. The
interrupt handler code was written in such a way that it would re-enable the
counter. That would lead to an unexpected interrupt later on.
This problem was easy to reproduce with
$ pmcstat -T -P instructions -t $pid
if the target process is sufficiently busy and there are context switches from
time to time. There would be a lot of interrupts to "race" with amd_stop_pmc()
called during the context switches. The problem affected only AMD processors.
While there, trace whether amd_intr() claimed an interrupt.
Reviewed by: jhb
MFC after: 2 weeks
The CHANSTS register is a split 64-bit register on CBDMA units before
hardware v3.3. If a torn read happens during ioat_process_events(),
software cannot know when to stop completing descriptors correctly.
So, just use the device-pushed main memory channel status instead.
Remove the ioat_get_active() seatbelt as well. It does nothing if the
completion address is valid.
Sponsored by: Dell EMC Isilon
There are 4 independent knobs in T5+ chips to include or exclude PAUSE
frames from the "total frames" and "multicast frames" counters in either
direction. This change lets the driver deal with any combination of
these settings.
but never released. Since no real hardware was released with this ID,
just drop it from the aacraid driver. This paves the path for future
drivers for hardware that actually has this ID.
Submitted by: Scott Benesh from Microsemi.
Differential Revision: https://reviews.freebsd.org/D8377
MFC After: 3 days
we have to refresh it ... always. This fixes problems reported in NetMap
with em(4) devices after conversion to extended descriptor format in
svn r293331.
Submitted by: luigi@
Reported by: franco@opnsense.org
MFC after: 2 days
- use PCI_VENDOR and PCI_DEVICE ids from a publicly allocated range
(thanks to RedHat)
- export memory pool information through PCI registers
- improve mechanism for configuring passthrough on different hypervisors
Code is from Vincenzo Maffione as a follow up to his GSOC work.
This paves way for more chimney sending buffer reorganization.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8343
