adapter to work around bugs in TSO handling at this speed.
em_init_locked is called during first boot of the adapter and will
see that link_speed is unitialized, effectively turning off tso for
all cards at all speeds, which I believe was *not* the intent.
Move the handling of TSO deactivation to the link handler where we can
more effectively make the decision about what to do. In addition,
completely purge the TSO capabilities instead of disabling just CSUM_TSO.
Thanks to jhb for explanation of the hw capabilites api.
Thanks to royger and cognet for testing the 100Mbit failure case to
ensure that their adapters do indeed still work.
MFC after: 1 week
Sponsored by: Limelight Networks
is not going to recover until the system is reset. Treat it as a special
case and don't allow it to fall through to quasi-success.
Reviewed by: ken, imp
Obtained from: Netflix
MFC after: 3 days
the components are reset). Therefore retries are pointless. This is very
visible in SATL systems, for example an LSI SAS controller and a SATA HDD/SSD.
Reviewed by: ken
Obtained from: Netflix
MFC after: 3 days
Bay Trail has three banks of GPIOs exposed to userland as /dev/gpiocN,
where N is 1, 2, and 3. Pins in each bank are pre-named to match names
on boards schematics: GPIO_S0_SCnn, GPIO_S0_NCnn, and GPIO_S5_nn.
Controller supports edge-triggered and level-triggered interrupts but
current version of the driver does not have interrupts support
Requests which cannot be satisfied by allocators at boot time often
have unrealizable parameters. Waiting for the pagedaemon' start would
hang the boot if done in the thread0 context and just never succeed if
executed from another thread. In fact, for very early stages, sleep
attempt panics with obscure diagnostic about the scheduler state, and
explicit panic in vm_wait() makes the investigation much shorter by
cut off the examination of the thread and scheduler.
Theoretically, some subsystem might grab a resource to exhaustion, and
free it later in the boot process. If this unlikely scenario does
appear for real, the way to diagnose the trouble can be revisited.
Reported by: emaste
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8421
The audio controller in the H3 is more or less the same as A10/A20 except
some registers are shuffled around. The mixer interface, however, is
completely different between SoCs. Separate a10_mixer_class and
h3_mixer_class implementations are now made available. This will also make
adding support for other SoCs easier in the future.
Reviewed by: andrew, ganbold
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8425
they shouldn't be.
I used this during driver bring-up to find that the Linux driver holds a
whole lot of locks whilst doing their equivalent of busdma operations.
If this works out well, it should be added to the other architecture busdma
implementations to aid in similar debugging.
Tested:
* bounce buffer and dmar busdma, Lenovo X230 laptop, all the internal
hardware
* ath(4) too
Discussed with: jhb
This is a long time coming. The general pieces have been floating around
in a local repo since circa 2012 when I dropped the net80211 support
into the tree.
This allows the per-chain RSSI and NF to show up in 'ifconfig wlanX list sta'.
I haven't yet implemented the EVM hookups so that'll show up; that'll come
later.
Thanks to Susie Hellings <susie@susie.id.au> who did the original work
on this a looong time ago for a company we both worked at.
be accessed by root. It uses unsigned ints instead of size_t
to preserve the ABI.
PR: 207627
Submitted by: ryan@ryanday.net (with slight tweaks)
MFC after: 1 month
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
To enable event sourcing from atkbd kern.evdev.rcpt_mask value
should have bit 3 set.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8381
The device doesn't accurately update the CHANCMP address with the device state
when the device is suspended or halted. So, read the CHANSTS register to check
for those states.
We still need to read the CHANCMP address for the last completed descriptor.
Sponsored by: Dell EMC Isilon
we never try to sleep while the thread is on a sleepqueue.
Reviewed by: jhb
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D8422
that are apparently misconfigured by the manufacturer and cause the mapping
logic to fail. The fallback allows drive numbers to be assigned based on the
PHY number that they're attached to. Add sysctls and tunables to overrid
this new behavior, but they should be considered only necessary for debugging.
Reviewed by: imp, smh
Obtained from: Netflix
MFC after: 3 days
Sponsored by: D8403
* Rename ARM_HAVE_MP_EXTENSIONS to ARM_USE_MP_EXTENSIONS and extend it to
handle more cases, including when SMP is not enabled.
* Check ARM_USE_MP_EXTENSIONS when building for ARMv7+, even if no SMP.
* Use ARM_USE_MP_EXTENSIONS in pmap-v6.c to detect when to set PRRR_NS1.
With this we should be able to boot on all ARMv7+ Cortex-A cores with
32-bit support.
Reviewed by: mmel, imp (earlier version)
Relnotes: yes
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8335
If dotdot lookup does not escape from the file descriptor passed as
the lookup root, we can allow the component traversal. Track the
directories traversed, and check the result of dotdot lookup against
the recorded list of the directory vnodes.
Dotdot lookups are enabled by sysctl vfs.lookup_cap_dotdot, currently
disabled by default until more verification of the approach is done.
Disallow non-local filesystems for dotdot, since remote server might
conspire with the local process to allow it to escape the namespace.
This might be too cautious, provide the knob
vfs.lookup_cap_dotdot_nonlocal to override as well.
Idea by: rwatson
Discussed with: emaste, jonathan, rwatson
Reviewed by: mjg (previous version)
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 week
Differential revision: https://reviews.freebsd.org/D8110
process of being unmounted. Previously it would skip them, even if the
unmount eventually failed eg due to the filesystem being busy.
This behaviour broke autounmountd(8) - if you tried to manually unmount
a mounted filesystem, using 'automount -u', and the autounmountd attempted
to refresh the filesystem list in that very moment, it would conclude that
the filesystem got unmounted and not try to unmount it afterwards.
Reviewed by: kib@
Tested by: pho@
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8030
While I'm here, move message status codes to hv_utilreg.h, since they
will be used by the upcoming VSS stuffs.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8391
lsdev should display detailed information about net devices only with -v
switch. This will make EFI and BIOS version of the loader to have the
same behavior.
Reviewed by: bapt, imp
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D8415
With guest trackpoint present trackpoint probing switched synaptics
device to absolute mode with different protocol instead of keeping it
in relative mode.
PR: 213757
Submitted by: Vladimir Kondratyev <wulf@cicgroup.ru>
MFC after: 1 week
Summary:
i.MX5 and PowerPC use a very similar eSDHC controller, which is also
similar to the uSDHC controller used by i.MX6. The imx_sdhci driver works
almost completely with PowerPC, with some minor tweaks.
There is one caveat with this: reset currently does not work on PowerPC, so has
been #ifdef'd out until this can be tracked down and fixed. If resets are done
the controller will timeout all data transactions. Without a reset, it appears
to work just fine.
This is part 3, following up r308186 and r308187.
Test Plan:
This has been tested on a PowerPC QorIQ P1022 board. It has not been
tested on i.MX, but no regressions are expected.
Reviewed By: imp
Differential Revision: https://reviews.freebsd.org/D8407
Some controllers (namely Freescale's eSDHC, tested) will continue to assert
the card removed or card insert interrupts even after being handled. To work
around this, disable watching the interrupt that just occurred until the
opposite interrupt is triggered.
Linux has a similar change in its driver to address the same problem.
* Starting a scan from wpa_supplicant or via ifconfig while associated,
should no longer cause firmware panics or abort early.
Tested:
* AC7260, STA mode
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8412
* SYNC_RESP_STRUCT and SYNC_RESP_PTR originate from the OpenBSD version of
iwm, and they weren't serving any real purpose in the FreeBSD port.
* We just do a single bus_dmamap_sync for syncing the complete received frame,
instead of explicitly bus_dmamap_sync-ing subranges of the frame like in
the OpenBSD iwm code.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7939
This allows us to make strong assertions about descriptor address
validity. Additionally, future generations of the ioat(4) hardware will
require contiguous descriptors.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
This paves the way for a contiguous descriptor array.
A contiguous descriptor array has the benefit that we can make strong
assertions about whether an address is a valid descriptor or not. The
other benefit is that future generations of I/OAT hardware will require
a contiguous descriptor array anyway. The downside is that after system
boot, big chunks of contiguous memory is much harder to find. So
dynamic scaling after boot is basically impossible.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
for dummynet, use the correct argument for that, remove the false coment
about the presence of struct ifnet.
Fixes the input match of dummynet l2 rules.
Obtained from: pfSense
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (Netgate)
in-progress count and the vnode. Prior to r188331, we always acquired
the vnode lock before incrementing the object's paging-in-progress count.
Now, we increment it before attempting to acquire the vnode lock with
LK_NOWAIT, but we never sleep acquiring the vnode lock while we have the
count incremented.
Reviewed by: kib
MFC after: 3 days
Before this an earlier writes to a ZVOL opened without FSYNC could get to
ZIL after later writes to the same ZVOL opened with FSYNC. Fix this by
replicating functionality of ZPL (zv_sync_cnt equivalent to z_sync_cnt),
marking all log records sync if anybody opened the ZVOL with FSYNC.
MFC after: 2 weeks
And put them under HN_IFSTART_SUPPORT, which is by default on until
we whack the if_start related bits from base system.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8392
Upstream the BUF_TRACKING and FULL_BUF_TRACKING buffer debugging code.
This can be handy in tracking down what code touched hung bios and bufs
last. The full history is especially useful, but adds enough bloat that
it shouldn't be enabled in release builds.
Function names (or arbitrary string constants) are tracked in a
fixed-size ring in bufs. Bios gain a pointer to the upper buf for
tracking. SCSI CCBs gain a pointer to the upper bio for tracking.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8366
Previously these were only declared under #ifdef SMP in <machine/smp.h>.
However, these variables are defind in pmap.c unconditionally, and efirt.c
references them unconditionally. This fixes non-SMP kernel builds.
Discussed with: kib
MFC after: 1 week
A grant-table user-space device will allow user-space applications to map
and share grants (Xen way to share memory) among Xen domains. This grant
table user-space device has been tested with the QEMU Qdisk Xen backed.
Submitted by: jaggi
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D7293
Add a reference count to xenisrc. This is required for implementation of
unmap-notifications in the grant table userspace device (gntdev). We need to
hold a reference to the event channel port, in case the user deallocates the
port before we send the notification.
Submitted by: jaggi
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D7429
first EFI device if we can't find the one from which the image was loaded.
Reviewed by: allanjude,imp,jhb
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6780
- Move the SYSINIT to DRIVER/SECOND, i.e. after the vm_guest becomes
determistic.
- Minor style changes.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8370
Mainly because the host side only set TCPCS and IPCS even for
UDP datagrams.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8369
And use large default temporary channel packer buffer; we really
don't want it to be expanded at run time.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8367
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
It is possible that wrmsr in amd_stop_pmc() causes an overflow in a counter
that it disables. In that case a non-maskable interrupt is generated. The
interrupt handler code was written in such a way that it would re-enable the
counter. That would lead to an unexpected interrupt later on.
This problem was easy to reproduce with
$ pmcstat -T -P instructions -t $pid
if the target process is sufficiently busy and there are context switches from
time to time. There would be a lot of interrupts to "race" with amd_stop_pmc()
called during the context switches. The problem affected only AMD processors.
While there, trace whether amd_intr() claimed an interrupt.
Reviewed by: jhb
MFC after: 2 weeks
Convert vm_fault_hold()'s Boolean variables that are only used
internally to "bool". Add a comment describing why the one
remaining "boolean_t" was not converted.
Reviewed by: kib
MFC after: 8 days
(gpt)zfsboot will read one-time boot directives from a special ZFS pool
area. The area was previously described as "Boot Block Header", but
currently it is know as Pad2, marked as reserved and is zeroed out on
pool creation. The new code interprets data in this area, if any, using
the same format as boot.config. The area is immediately wiped out.
Failure to parse the directives results in a reboot right after the
cleanup. Otherwise the boot sequence proceeds as usual.
zfsbootcfg writes zfsboot arguments specified on its command line to the
Pad2 area of a disk identified by vfs.zfs.boot.primary_pool and
vfs.zfs.boot.primary_vdev kenv variables that are set by loader during
boot. Please see the manual page for more.
Thanks to all who reviewed, contributed and made suggestions! There are
many potential improvements to the feature, please see the review for
details.
Reviewed by: wblock (docs)
Discussed with: jhb, tsoome
MFC after: 3 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D7612
not a bitfield. For the intended usage - being passed either MNT_WAIT,
or MNT_NOWAIT - this shouldn't introduce any changes in behaviour.
Reviewed by: jhb@
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8373
The CHANSTS register is a split 64-bit register on CBDMA units before
hardware v3.3. If a torn read happens during ioat_process_events(),
software cannot know when to stop completing descriptors correctly.
So, just use the device-pushed main memory channel status instead.
Remove the ioat_get_active() seatbelt as well. It does nothing if the
completion address is valid.
Sponsored by: Dell EMC Isilon
There are 4 independent knobs in T5+ chips to include or exclude PAUSE
frames from the "total frames" and "multicast frames" counters in either
direction. This change lets the driver deal with any combination of
these settings.
but never released. Since no real hardware was released with this ID,
just drop it from the aacraid driver. This paves the path for future
drivers for hardware that actually has this ID.
Submitted by: Scott Benesh from Microsemi.
Differential Revision: https://reviews.freebsd.org/D8377
MFC After: 3 days
data structure sizes when mounting and reloading UFS/FFS
filesystems by using a u_long rather than an int for the size.
Reported by: Mariusz Zaborski <oshogbo@>
MFC after: 1 week
It allows to avoid extra GEOM providers flapping without significant need.
Since GEOM got resize support, we don't need to reopen provider to get new
size. If provider was orphaned and no longer valid, ZFS should already
know that, and in such case reopen should be done in full as expected.
MFC after: 2 weeks
In case of vdev detach, causing top level mirror vdev destruction, leaf
vdev changes its GUID to one of the destroyed mirror, that creates race
condition when GUID in vdev label may not match one in the pool config.
This change replicates logic nuance of vdev_validate() by adding special
exception, matching the vdev GUID against the top level vdev GUID.
Since this exception is not completely reliable (may give false positives
if we fail to erase label on detached vdev), use it only as last resort.
Quick way to reproduce this scenario now is detach vdev from a pool with
enabled autoextend. During vdev detach autoextend logic tries to reopen
remaining vdev, that always fails now since in-memory configuration is
already updated, while on-disk labels are not yet.
MFC after: 2 weeks
Just using vm_paddr_t value with all bits set.
That should work as long as the type is unsigned.
While there, fix a couple of whitespace issues nearby.
MFC after: 1 week
X-MFC with: r307903
we have to refresh it ... always. This fixes problems reported in NetMap
with em(4) devices after conversion to extended descriptor format in
svn r293331.
Submitted by: luigi@
Reported by: franco@opnsense.org
MFC after: 2 days
The userspace case was already handled by pmap_allocpte(). For kernel
VA, page table page must exist, and demote cannot fail, so we need to
just call pmap_demote_pde(). Also note that due to the machine AS
layout, promotions in the KVA on i386 are highly unlikely, so this
change is mostly for completeness.
Reviewed by: alc, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8323
which also use buffer cache.
Most important addition to the code is the handling of filesystems
where the block size is less than the machine page size, which might
require reading several buffers to validate single page.
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
volume limits. In particular:
- Assert that usemap_alloc() and usemap_free() cluster number argument
is valid.
- In chainlength(), return 0 if cluster start is after the max cluster.
- In chainlength(), cut the calculated cluster chain length at the max
cluster.
- For true paranoia, after the pm_inusemap is calculated in
fillinusemap(), reset all bits in the array for clusters after the
max cluster, as in-use.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Use the same logic to calculate the nominal CPU frequency from the P-state
MSRs on family 0x12, 0x15, and 0x16 CPUs as is used for family 0x10.
Family 0x14 was included in the original patch in the PR but I left that
out as the BIOS writer's guide for family 0x14 CPUs show a different layout
for the relevant MSR and include a different formulate for calculating the
frequency.
While here, simplify a few expressions and print out the family of
unsupported CPUs in hex rather than decimal.
PR: 212020
Submitted by: Anthony Jenkins <Scoobi_doo@yahoo.com>
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D7587
Reject attempts to read from or memory map offsets in /dev/mem that are
beyond the maximum-supported physical address of the current CPU.
Reviewed by: kib
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D7408
- use PCI_VENDOR and PCI_DEVICE ids from a publicly allocated range
(thanks to RedHat)
- export memory pool information through PCI registers
- improve mechanism for configuring passthrough on different hypervisors
Code is from Vincenzo Maffione as a follow up to his GSOC work.
illumos/illumos-gate@260af64db7260af64db7https://www.illumos.org/issues/3746
From the original change log:
It was possible for a reference to be added even with the lock held, and
for references added just after a lock release to be lost.
This bug was also independently found and reported in wesunsolve.net
issues 6985013 6995524.
In zrl_add(), always use an atomic operation to update the refcount.
The mutex in the ZRL only guarantees that wakeups occur for waiters on the
lock. It offers no protection against concurrent updates of the refcount.
The only refcount transition that is safe to perform without an atomic
operation is from ZRL_LOCKED back to 0, since this can only be performed
by the thread which has the ZRL locked.
Authored by: Will Andrews <will@freebsd.org>
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Reviewed by: Pavel Zakharov <pavel.zakha@gmail.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Reviewed by: Justin T. Gibbs <gibbs@scsiguy.com>
Approved by: Matt Ahrens <mahrens@delphix.com>
Author: Youzhong Yang <yyang@mathworks.com>
PR: 204037
MFC after: 1 week
This paves way for more chimney sending buffer reorganization.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8343
directory create and delete operations. If it ever finds a directory
with a link count less than 2, it panics. Thus, an rm -rf that
encounters a directory with a link count below 2 causes a kernel
panic. The proposed fix is to return the error EINVAL rather than
panicing. The effect is that the requested operation is not done,
but the system continues to run. At a more convenient later time,
the filesystem can be unmounted and cleaned (with fsck or journal
run). Once cleaned, the operation can be rerun to successful
completion.
This fix takes that approach. The panic message has been converted
into a uprintf(9) to provide the user with the inode number and
filesystem mount point of the offending directory and EINVAL is
returned for the operation.
The long (three year) delay in fixing this problem occurred because
the bug was misclassified when originally assigned and only this week
was found during a sweep of old unresolved bug reports.
PR: 180894
Reviewed by: kib
MFC after: 2 weeks
EFER_NXE is set in the EFER MSR by initializecpu() and must be set on all
CPUs in the system. When PG_NX support was added to PAE on i386, the
block to enable EFER_NXE was placed in a section of initializecpu() that
only runs if 'cpu == CPU_686'. During early boot, locore does an
initial pass to set cpu that sets it to CPU_686 on all CPUs later than
a Pentium. Later, printcpuinfo() adjusts the 'cpu' variable on
PII and later CPUs to one of CPU_PII, CPU_PIII, or CPU_P4. However,
printcpuinfo() is called after initializecpu() on the BSP, so the BSP
would enable EFER_NXE and pg_nx. The APs execute initializecpu() much
later after printcpuinfo() has run. The end result on a modern CPU was
that cpu was set to CPU_PIII when the APs invoked initializecpu(), so
they did not enable EFER_NXE. As a result, the APs would fault when
trying to access any pages marked with PG_NX set.
When booting a 2 CPU PAE kernel in bhyve this manifested as a hang before
single user mode. The attempt to execute /bin/init tried to copy out
the exec strings (argv, etc.) to a non-executable mapping while running
on the AP. The instruction kept faulting due to invalid bits in the PTE
in an infinite loop.
Fix this by moving the code to enable EFER_NXE out of the switch statement
on 'cpu' and always doing it if 'amd_feature' supports AMDID_NX.
MFC after: 2 weeks
Add missing fields ('sr' and 'mc_tls') to 'struct sigcontext'.
The kernel doesn't use 'struct sigcontext' but instead uses 'ucontext_t'
which includes 'mcontext_t' in 'struct sigframe' to build the signal frame.
As a result, this change is not an ABI change but simply making
'struct sigcontext' correct. Note that 'struct sigcontext' is only used
for "Traditional BSD style" signal handlers.
While here, rename the 'xxx' field to '__spare__' to match 'mcontext_t'.
Sponsored by: DARPA, AFRL
introduced with r261242. The useful and expected soisconnected()
call is done in tcp_do_segment().
Has been found as part of unrelated PR:212920 investigation.
Improve slightly (~2%) the maximum number of TCP accept per second.
Tested by: kevin.bowling_kev009.com, jch
Approved by: gnn, hiren
MFC after: 1 week
Sponsored by: Verisign, Inc
Differential Revision: https://reviews.freebsd.org/D8072
them. Previously this would walk past the end of the array and print
whatever happened to be after the trapframe struct.
MFC after: 1 week
Sponsored by: DARPA, AFRL
And use it for vmbus channel logging, which can log the channel
owner's name properly, instead of vmbus0.
Submitted by: QianYue You <t-youqi microsoft com>
MFC after: 1 week
Sponsored by: Microsoft
The directly following m_defrag() call can wait, so there is no reason this
call can't as well.
Reported by: Coverity
CID: 1353551
Sponsored by: Dell EMC Isilon
FICL definitions not in ficl/ficl32 files broke this generally. This
makes that stuff conditional on BOOT_FORTH. Also, move definitions
related to the architecture (FICL_CPUARCH and friends) into
Makefile.ficl that all parts of the tree that include files with ficl
need to include (but only if MK_FORTH == yes). In addition, had to fix
library ordering issue with LIBSTAND to keep it last. Without boot
forth, there's no references to memset to bring in memset.o from
libstand.a to satisfy libgeliboot.a's use of it. Listing libstand last
solves this issue (and it's the proper place for libstand to boot).
PLL1 is used by the cpu core, allowing changing freq is needed for cpufreq.
The factors table contains all the frequencies in the operating point table
present in the DTS.
MFC after: 1 week
these show a 9-10% reduction in user and system time for a buildworld -j48.
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
* On arm64 we need to use the ${MACHINE_CPUARCH} subdirectory.
* env.c is only needed when using forth so only build it there.
Sponsored by: ABT Systems Ltd
hardware that supports the mp extensions. If so it should use the broadcast
tlb invalidate instructions as other CPUs or devices may need to know about
the invalidation.
To simplify the code have the compiler optimise out the else case when not
builing for Cortex-A8.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8092
To achieve that the whole svm_softc is allocated with contigmalloc now.
It would be more effient to de-embed those arrays and allocate only them
with contigmalloc.
Previously, if malloc(9) used non-contiguous pages for the arrays, then
random bits in physical pages next to the first page would be used to
determine permissions for I/O port and MSR accesses. That could result
in a guest dangerously modifying the host hardware configuration.
One example is that sometimes NMI watchdog driver in a Linux guest
would be able to configure a performance counter on a host system.
The counter would generate an interrupt and if hwpmc(4) driver is loaded
on the host, then the interrupt would be delivered as an NMI.
Discussed with: jhb
Reviewed by: grehan
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8321
loss event but not use or obay the recommendations i.e. values set by it in some
cases.
Here is an attempt to solve that confusion by following relevant RFCs/drafts.
Stack only sets congestion window/slow start threshold values when there is no
CC module availalbe to take that action. All CC modules are inspected and
updated when needed to take appropriate action on loss.
tcp_stacks/fastpath module has been updated to adapt these changes.
Note: Probably, the most significant change would be to not bring congestion
window down to 1MSS on a loss signaled by 3-duplicate acks and letting
respective CC decide that value.
In collaboration with: Matt Macy <mmacy at nextbsd dot org>
Discussed on: transport@ mailing list
Reviewed by: jtl
MFC after: 1 month
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D8225
In r304435, ip_output() was changed to use the result of the route
lookup to decide whether the outgoing packet was a broadcast or
not. This introduced a regression on interfaces where
IFF_BROADCAST was not set (e.g. point-to-point links), as the
algorithm could incorrectly treat the destination address as a
broadcast address, and ip_output() would subsequently drop the
packet as broadcasting on a non-IFF_BROADCAST interface is not
allowed.
Differential Revision: https://reviews.freebsd.org/D8303
Reviewed by: jtl
Reported by: ambrisko
MFC after: 2 weeks
X-MFC-With: r304435
Sponsored by: Dell EMC Isilon
- Make !KDB config buildable.
- Simplify interface to nmi_handle_intr() by evaluating panic_on_nmi
in one place, namely nmi_call_kdb(). This allows to remove do_panic
argument from the functions, and to remove i386/amd64 duplication of
the variable and sysctl definitions. Note that now NMI causes
panic(9) instead of trap_fatal() reporting and then panic(9),
consistently for NMIs delivered while CPU operated in ring 0 and 3.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
environment variable to allow conditional compilation based on EFI
being present or not. Provide efi-setenv, efi-getenv, and
efi-unsetenv, though those need improvement. Move the efi definition
to libefi (but include a reference so they get included).
Push-Pull Two Wire interface is a almost compatible iic like bus used
in sun6i SoC. It's only use is to communicate with the power management IC.
Reviewed by: jmcneill
MFC after: 1 week
Relnotes: yes
contiguous regions in an mbuf chain.
If the payload of an mbuf ends at a page boundary count_mbuf_nsegs would
incorrectly consider the next mbuf's payload physically contiguous based
solely on a KVA comparison.
MFC after: 1 week
Sponsored by: Chelsio Communications
On several Intel chipsets, diagnostic NMIs sent from BMC or NMIs
reporting hardware errors are broadcasted to all CPUs.
When kernel is configured to enter kdb on NMI, the outcome is
problematic, because each CPU tries to enter kdb. All CPUs are
executing NMI handlers, which set the latches disabling the nested NMI
delivery; this means that stop_cpus_hard(), used by kdb_enter() to
stop other cpus by broadcasting IPI_STOP_HARD NMI, cannot work. One
indication of this is the harmless but annoying diagnostic "timeout
stopping cpus".
Much more harming behaviour is that because all CPUs try to enter kdb,
and if ddb is used as debugger, all CPUs issue prompt on console and
race for the input, not to mention the simultaneous use of the ddb
shared state.
Try to fix this by introducing a pseudo-lock for simultaneous attempts
to handle NMIs. If one core happens to enter NMI trap handler, other
cores see it and simulate reception of the IPI_STOP_HARD. More,
generic_stop_cpus() avoids sending IPI_STOP_HARD and avoids waiting
for the acknowledgement, relying on the nmi handler on other cores
suspending and then restarting the CPU.
Since it is impossible to detect at runtime whether some stray NMI is
broadcast or unicast, add a knob for administrator (really developer)
to configure debugging NMI handling mode.
The updated patch was debugged with the help from Andrey Gapon (avg)
and discussed with him.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8249
The feature flags chek is missing the corner case where we have valid pool
version, but feature flags are not enabled - as for example plain v28 pool.
This update does fix the boot support for such pools.
Reviewed by: avg, allanjude
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D8331
Link status check is much more lightweight than network change detection.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8311
This will not happen in real world, since TX consumption of the vmbus
TX bufring is limitted. Better safe than sorry.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8309
All RNDIS control messages have used SG list for a while. This makes
the send context suitable for further refactoring.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8308
prevent overheating.
When sensor 0's alarm interrupt is fired, set a throttle flag. Further
requests to set CPU frequency will be rejected until sensor 0's temperature
returns to a level below the hot temperature threshold.
Relnotes: yes
native fueword64(9) still, use proper type for local where fuword64()
result is stored.
Note that fueword64() is unused in the tree.
Submitted by: Chunhui He <hchunhui@mail.ustc.edu.cn>
PR: 212520
MFC after: 1 week
- Use ums lock as evdev lock
- Do not cap axes values to sysmouse limits for evdev reports
- Do not map T-axis events to buttons for evdev reports
- Use shortcuts for event reporting
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
MFC after: 1 week
Add wrappers around generic evdev_push_event for specific event types:
EV_KEY/EV_REL/EV_ABS etc...
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
If the device tree doesn't contain a cpu-handle field in any bman-portal or
qman-portal, it will exit without setting up the devinfo, leaving it
uninitialized. This will lead to attempts to free random memory, and ultimately
panic.
Summary:
The Freescale e500v2 PowerPC core does not use a standard FPU.
Instead, it uses a Signal Processing Engine (SPE)--a DSP-style vector processor
unit, which doubles as a FPU. The PowerPC SPE ABI is incompatible with the
stock powerpc ABI, so a new MACHINE_ARCH was created to deal with this.
Additionaly, the SPE opcodes overlap with Altivec, so these are mutually
exclusive. Taking advantage of this fact, a new file, powerpc/booke/spe.c, was
created with the same function set as in powerpc/powerpc/altivec.c, so it
becomes effectively a drop-in replacement. setjmp/longjmp were modified to save
the upper 32-bits of the now-64-bit GPRs (upper 32-bits are only accessible by
the SPE).
Note: This does _not_ support the SPE in the e500v1, as the e500v1 SPE does not
support double-precision floating point.
Also, without a new MACHINE_ARCH it would be impossible to provide binary
packages which utilize the SPE.
Additionally, no work has been done to support ports, work is needed for this.
This also means no newer gcc can yet be used. However, gcc's powerpc support
has been refactored which would make adding a powerpcspe-freebsd target very
easy.
Test Plan:
This was lightly tested on a RouterBoard RB800 and an AmigaOne A1222
(P1022-based) board, compiled against the new ABI. Base system utilities
(/bin/sh, /bin/ls, etc) still function appropriately, the system is able to boot
multiuser.
Reviewed By: bdrewery, imp
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D5683
libc++'s stddef.h includes an existing definition of max_align_t for
C++11, but it is only defined for C++, not for C. In addition, GCC and
clang both define an alternate version of max_align_t that uses a
union of multiple types rather than a plain long double as in libc++.
This adds a __max_align_t to <sys/_types.h> that matches the GCC and
clang definition that is mapped to max_align_t in <stddef.h>.
PR: 210890
Reviewed by: dim
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8194
In sendit(), if mp->msg_control is present, then in sockargs() we are
allocating mbuf to store mp->msg_control. Later in kern_sendit(), call
to getsock_cap(), will check validity of file pointer passed, if this
fails EBADF is returned but mbuf allocated in sockargs() is not freed.
Made code changes to free the same.
Since freeing control mbuf in sendit() after checking (control != NULL)
may lead to double freeing of control mbuf in sendit(), we can free
control mbuf in kern_sendit() if there are any errors in the routine.
Submitted by: Lohith Bellad <lohith.bellad@me.com>
Reviewed by: glebius
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D8152
