RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
When updating a VSI, save off the number of allocated and
unallocated VSIs as we do when adding a VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fix the driver load failure with linking with some
PHY types, as the amount of time it takes for the
GLGEN_RSTAT_DEVSTATE to be set increases greatly on those PHY
types, which can lead to a timeout.
Fixes: 9aeefed055 ("i40e/base: support ESS")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In Multi-Function Mode (MFP) particularly when the PF VSI is set
in limited promiscuous mode, the HW switch was still mirroring the
outgoing packets from other VSIs (VF/VMdq) onto the PF VSI.
This sets a new bit to avoid above mirroring, and it is in limited
promiscuous on the PF VSI in MFP which is similar to default port
VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds functions to blink led on devices using a new
PHY since MAC registers used in other designs do not work in
this device configuration.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the support code for calling the AdminQ API call
aq_set_switch_config.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the use of the new shared MAC filter bit for multicast
and broadcast filters in order to make better use of the
filters available from the device.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch fixes a problem where the NVMUpdate Tool, when
using the PHY NVM feature, gets bad data from the PHY because
of contention on the MDIO interface from get phy capability
calls from the driver during regular operations. The problem
is fixed by adding a check if media is available before calling
get phy capability function because that bit is not set when
device is in PHY interaction mode.
Fixes: 842ea19963 ("i40e/base: save link module type")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The device capabilities were defined in two places, and neither had
all the definitions. It really belongs with the AQ API definition,
so this patch removes the other set of definitions and fills out the
missing item.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The recently added proxy opcodes should be available only with
X722_SUPPORT, so move them into the #ifdef, and reorder these
to be in numerical order with the rest of the opcodes. Several
structs that were added are unnecessary, so they are removed
here.
Fixes: 788fc17b2d ("i40e/base: support proxy config for X722")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The recently added Wakeup On Line (WOL) opcodes should be
available only with X722_SUPPORT, so move them into the #ifdef,
and reorder these to be in numerical order with the rest of the
opcodes. Several structs that were added are unnecessary, so
they are removed here.
Fixes: 3c89193a36 ("i40e/base: support WOL config for X722")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add new Device ID's for backplane and QSFP+ adapters, and delete
deprecated one for backplane.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In one obscure corner case, it was possible to clear the NVM update
wait flag when no update_done message was actually received. This
patch cleans the event descriptor before use, and moves the opcode
check to where it won't get done if there was no event to clean.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The standard way to check if the AQ is enabled is to look at
the count field. So it should only set this field after it has
successfully allocated memory.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
It's possible that while waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If it then attempts to use the queue, it will panic.
It adds a check for this condition on the receive side. This
matches an existing check on the send queue side.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
XL710/X710 devices requires FW version checks to properly handle
DCB configurations from the FW while other devices (e.g. X722)
do not, so limit these checks to XL710/X710 only.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In X722, NVM reads can't be done through SRCTL registers.
And require AQ calls, which require grabbing the NVM lock.
Unfortunately some paths need the lock to be acquired once
and do a whole bunch of stuff and then release it.
This patch creates an unsafe version of the read calls, so
that it can be called from the paths that need the bulk access.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Instead of doing the MAC check, use a flag that gets set per
MAC. This way there are less chances of user error and it
can enable multiple MACs with the capability in a single place
rather than cluttering the code with MAC checks.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
SW needs to acquire the NVM ownership before issuing an AQ read
to the X722 NVM otherwise it will get EBUSY from the firmware.
Also it should be released when done.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fix compilation warnings in base code on some platforms.
Fixes: bd6651c2d2 ("i40e/base: use bit shift macros")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Use ether API of 'is_valid_assigned_ether_addr' to validate
MAC address.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Generate a MAC address for each VF during PF host
initialization.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
VLAN filtering was always performed, even if hw_vlan_filter was
disabled. During device initialization, default filter
RTE_MACVLAN_PERFECT_MATCH was applied. In this situation, all incoming
VLAN frames were dropped by the card (increase of the register RUPP - Rx
Unsupported Protocol).
In order to restore default behavior, if HW VLAN filtering is activated,
set a filter to match MAC and VLAN. If not, set a filter to only match
MAC.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 912b595146 ("i40e: mac vlan filter")
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The no-refcount path was being taken without the application opting
in to it.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Reported-by: Mike Stolarchuk <mike.stolarchuk@bigswitch.com>
Signed-off-by: Rich Lane <rich.lane@bigswitch.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The names of function for tunnel port configuration are not
accurate. They're tunnel_add/del, better change them to
tunnel_port_add/del.
The old functions are directly replaced because the API and ABI
compatibility of ethdev are already broken in 16.04.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The array 'ptype_table' was defined in depth of 'UINT8_MAX' which
is 255, while the querying index could be from 0 to 255. The issue
can be fixed with expanding the array to one more element.
Fixes: 9571ea0284 ("i40e: replace some offload flags with unified packet type")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
PCIe feature of 'Extended Tag' is important for 40G performance.
It adds its enabling during each port initialization, to ensure
the high performance.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Macros RTE_MBUF_DATA_DMA_ADDR and RTE_MBUF_DATA_DMA_ADDR_DEFAULT
are defined in each PMD driver file. Convert macros to inline
functions and move them to common lib/librte_mbuf/rte_mbuf.h file.
PMD drivers include rte_mbuf.h file directly/indirectly hence no
additioanl header file inclusion is necessary.
Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
fix the error reported by checkpatch:
"ERROR: return is not a function, parentheses are not required"
remove parentheses in return like:
"return (logical expressions)"
remove parentheses in return a function like:
"return (rte_mempool_lookup(...))"
Fixes: 6307b909b8 ("lib: remove extra parenthesis after return")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Coverity issue reported like
CID 119268 (#1 of 1): Unintended sign extension
(SIGN_EXTENSION)sign_extension: Suspicious implicit sign extension:
vsi_id with type unsigned short (16 bits, unsigned) is promoted in
vsi_id << 23 to type int (32 bits, signed), then sign-extended to type
unsigned long (64 bits, unsigned). If vsi_id << 23 is greater than
0x7FFFFFFF, the upper bits of the result will all be 1.
Fixes: 88ebc2b7f9 ("i40e: extend flow director to support VF")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
In FreeBsd driver, the max frame size is changed to MTU, but not
keep the default value defined in DataSheet. When DPDK runs on that
NIC, the configured value is not expected.
This patch sets the max frame size to default when initialization.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It corrects the input set values to be set for vlan or
double vlan.
Fixes: 98f0557076 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
This is one of those trivial things git and other tools complain
about.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
When dev_stop is called in i40evf pmd driver, queues are switched off
to stop receiving and transmitting. But the mac address of this VF
still exists in VEB switch.
To stop the traffic from VSI level, the mac address need to be removed
too. Then the bandwidth for this SRIOV VSI can be freed.
This patch fix this issue.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
There is a new function in the EAL API for internal use.
It has neither a proper prefix nor a .map export:
libethdev.so: undefined reference to `is_xen_dom0_supported'
Fixes: 719dbebceb ("xen: allow determining DOM0 at runtime")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
There is a compilation issue with some compilers.
In i686 platform, long is 32bit, so XXX_CYCLECOUNTER_MASK
need define as 'ULL'
Fixes: 9c857bf6be ("igb: support ieee1588 functions for device time")
Fixes: 1c4445e1f2 ("ixgbe: support ieee1588 functions for device time")
Fixes: f3a4e40eca ("i40e: support ieee1588 functions for device time")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
It fixes the issue of not configuring rss key enable flags
when there is no rss key available.
Fixes: 647d1eaf75 ("i40evf: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
For i40e vf driver, should use I40EVF_WRITE_FLUSH to flush
configuration but not I40E_WRITE_FLUSH. This patch fixed this issue.
Fixes: be6c228d4d (i40evf: support Rx interrupt)
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
If DCB is not enabled, the BW info is not stored for VSI. This
patch fixes this issue by merging functions i40e_vsi_dump_bw_config
and i40e_vsi_get_bw_info together.
Fixes: c8b9a3e3fe (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
When NVM version is updated to 5.x, DCB can not be configured. This
issue is because of the FW version validation is not correct.
This patch fixed this issue.
Fixes: c8b9a3e3fe (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yulong Pei <yulong.pei@intel.com>
As firmware does not support any link control from software driver
side, any phy config should be ignored as a workaround. Otherwise
the link might not be up again after binding back to kernel driver.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It fixes the issue of not re-configuring hash enable flags (HENA)
if there is no key.
Fixes: d0a349409b ("i40e: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes the crc bytes from byte counter statistics.
Doing so fixes a bug that CRC bytes were included on TX but not
on RX, causing mismatch of bytes received / sent.
Fixes: 9aace75fc8 ("i40e: fix statistics")
Reported-by: Weichun Chen <weichunx.chen@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
This patch refactors the queue and priority statistic handling.
Generic queue stats are presented by rte_eth_xstats_get(), and the
i40e_xstats_get() exposes only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
It fixes the issue of trying to allocate more VSIs for VMDq than
hardware remaining. It adds a check of the hardware remaining
before allocating VSIs for VMDq.
Fixes: c80707a0fd ("i40e: fix VMDq pool limit")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
This patch fixes a bug where only some of the statistics were being
reset when calling rte_eth_stats_reset() or rte_eth_xstats_reset().
As both the stats reset and xstats reset do the same, refactor away
the duplicated function.
This patch marks the VSI to update its offset, causing the stats be
look like they are reset.
Fixes: 9aace75fc8 ("i40e: fix statistics")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This fixes the issue of not freeing memzone in a call to free the
memory for adminq DMA.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
It fixes the issue of cannot using more than 1 poor for VMDq,
according to the queues left.
Fixes: 705b57f820 ("i40e: enlarge the number of supported queues")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Fix for the following error on icc 2015, due to incorrect type:
drivers/net/i40e/i40e_fdir.c(1376): error #188:
enumerated type mixed with another type
case RTE_ETH_FDIR_FILTER_INPUT_SET_SELECT:
Fixes: 98f05570 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It fixes compile issue on ICC 13.0.0.
Error logs:
i40e_ethdev.c(7943): error #188: enumerated type mixed with another type
Fixes: c8b9a3e3fe ("i40e: support DCB mode")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Add support for RTE_ETH_FDIR_PASSTHRU flow director behavior so
output queue is assigned by other filters.
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Following the same approach taken with dev_started field
in rte_eth_dev_data structure, this patch adds two new fields
in it, rx_queue_state and tx_queue_state arrays, which track
which queues have been started and which not.
This is important to avoid trying to start/stop twice a queue,
which will result in undefined behaviour
(which may cause RX/TX disruption).
Mind that only the PMDs which have queue_start/stop functions
have been changed to update this field, as the functions will
check the queue state before switching it.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch enables rx interrupt support on i40e VF and some necessary
change on PF IOV mode to support VF.
On PF side, running in IOV mode via uio won't allow rx interrupt
which is exclusive with mbox interrupt in single vector competition.
On VF side, one single vector is shared for all the rx queues.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
The patch enables rx interrupt support on i40e PF non-IOV mode.
Per queue rx interrupt works on vfio, however on uio, all rx queues
share one interrupt vector.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
The old statistics on i40e only counted the packets on ports.
So the discarding packets on VSI were not counted.
This patch is to make statistics for packets both on ports and VSI.
Also update release notes.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
By default, only first 3 bytes of GRE key will be used for hash or
FD calculation. With these changes, it can select 3 or 4 bytes of
GRE key for hash or FD calculation.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
The default input set of fields of a received packet are loaded from
firmware, which cannot be modified even users want to use different
fields for RSS or flow director. Here adds more flexibilities of
selecting packet fields for hash calculation or flow director for
users.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
It enlarges the number of supported queues to hardware allowed
maximum. There was a software limitation of 64 per physical port
which is not reasonable.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It adjusts the number of queues for RSS from power of 2 to any as
long as it does not exceeds the hardware allowed.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Use new function rte_eth_copy_pci_info.
Copy device info for the following pdevs:
bnx2x
cxgbe
e1000
enic
fm10k
i40e
ixgbe
mlx4
mlx5
virtio
vmxnet3
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
It supports both Admin queue based and directly writing registers
based RSS hash key and lookup table configuration, as X722 supports
AQ based configuration.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
It supports both Admin queue based and directly writing registers
based RSS hash key and lookup table configuration, as X722 supports
AQ based configuration.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In order to provide users early access of X722 and its A0 hardware,
new device IDs are added, and also compilation with those support
in base driver is enabled.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add implementation of xstats() functions in i40evf PMD.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
Add xstats functions to i40e PMD, allowing extended statistics
to be retrieved from the NIC and exposed to the DPDK.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
According to XL710 datasheet:
RX QLEN restrictions: When the PXE_MODE flag in the GLLAN_RCTL_0
register is cleared, the QLEN must be whole number of 32
descriptors.
TX QLEN restrictions: When the PXE_MODE flag in the GLLAN_RCTL_0
register is cleared, the QLEN must be whole number of 32
descriptors.
So make sure that for both RX and TX queues number of HW descriptors is
a multiple of 32.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds one new API to get dcb related info.
rte_eth_dev_get_dcb_info
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch enables DCB feature on Intel XL710/X710 NICs. It includes:
Receive queue classification based on traffic class
Round Robin ETS schedule (rx and tx)
Priority flow control
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
To support FVL PMD can select which RX and TX function should be used
according to the queue config.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
To support the multiple segments in one packets when the received pkts exceed
one buffer size.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
The way to increase the performance of the vPMD TX is to use some fast mbuf
release method compares to the scalar TX.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
The vPMD RX function uses the multi-buffer and SSE instructions to
accelerate the RX speed, but now the pktype cannot be supported by the vPMD RX,
because it will decrease the performance heavily.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
Feature Add: Rx/Tx flow control support for the i40e
All the Rx/Tx LFC enable/disable operation is done by the F/W,
so PMD driver need to use the Set PHY Config AD command to trigger the PHY
to do the auto-negotiation, after the Tx/Rx pause ability is negotiated,
the F/W will help us to set the related LFC enable/disable registers.
PMD driver also need to configure the related registers to control
how often to send the pause frame and what the value in the pause frame.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
If DPDK is used on VF while the host is using Linux Kernel driver
as PF driver on FVL NIC, then VF Rx is reported only in batches of
4 packets. It is due to the kernel driver assumes VF driver is working
in interrupt mode, but DPDK VF is working in Polling mode.
This patch fixes this issue by using the V1.1 virtual channel with
Linux i40e PF driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds a workaround to drop flow control frames from being
transmitted from VSIs.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Fixes a minor definition change in the Rx descriptor.
Also adds FortPark specific changes to the Descriptors.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Adds support to retrieve and parse WoL/Proxy capabilities from the
device/function list.
Also saves WR_CSR_PROT field from DEV/FUNC capabilities.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Adds admin q function for "Set Wake on LAN Filter AQ"
and "Get Wake Up Reason AQ".
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add AQ functions to handle RSS Key and LUT programming.
This is needed for FortPark RSS support.
FortPark has additional PCTYPES supported for RSS
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds registers and bit field definitions specific to FortPark.
Most of these new registers are related to PE (IWARP), Reset, NVM, RSS
and ATR changes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This is to allow quick check for FCoE capability is enabled or not
in device function before any SW overrides.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().
For pble resource management, it is more efficient for it to manage its
backing pages. For VF, pble backing page addresses will be send to PF
driver for pble resource.
The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
In order to support some extra Solaris features the Solaris VF drivers need
additional configuration data from the PF that aren't provided with the current
virtual channel commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The struct i40e_aqc_get_cee_dcb_cfg_v1_resp was originally defined with
word boundary layout issues, which most compilers deal with by silently
adding padding, making the actual struct larger than designed.
This patch adds an extra byte in fields reserved3 and reserved4 to directly
acknowledge that padding.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The assignments of addr_high and addr_low were not only wrong because
they were assigning virtual addresses to a hardware accessed variable,
but they were shortly thereafter overwritten by the send_asq_command
call with a non-NULL third argument (buffer) with correctly formatted
data.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Use INLINE macro for better cross-platform code management.
Clean up some unnecessary logic jumping and drop a variable.
There was one more __FUNCTION__ reference that wasn't needed.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add the new Port link status bit and rename the link status to function
link status.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type even if the
enum lists are different.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This will help us avoid a whole bunch of log messages when the driver
is running.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The Flex10 device/function capability has been upgraded to revision 2
to include information needed to support Flex-10 DCC and DCI
configurations. This patch adds new fields to the i40e_hw_capabilities
structure and updates i40e_parse_discover_capabilities functions to
extract them from the AQ response. Naming convention has changed to use
flex10 mode instead of existing mfp_mode_1.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information will
help us determine what speeds the device is capable of when link is
down.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch prepares the LLDP MIB in IEEE TLV format based on
the local dcb config.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds parsing for CEE DCBX TLVs from the LLDP MIB.
While the driver gets the DCB CEE operational configuration from Firmware
using the "Get CEE DCBX Oper Config" AQ command there is a need to get
the CEE DesiredCfg Tx by firmware and DCB configuration Rx from peer; for
debug and other application purposes.
Also gets rid of unused locals variables.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with linux kernel requirements.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
With latest LANconf and NVMupdate tools, pf_reset failed due to Firmware not
being ready, so this patch increases I40E_PF_RESET_WAIT_COUNT to 200, using
original value defined for A0 silicon, in order to make sure that FW is ready.
Test result indicates that firmware became ready at the loop count of 114.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
There were quite a few issues when the wrong defines were getting used
in the VF driver. This patch defines a new #define PF_DRIVER.
All the PF specific register definitions are wrapped in it.
The drivers will have to be updated to use the define in the PF
driver builds. Makes for a very short register.h for VF drivers.
Also fixes the code where PF driver register fields were getting used for
VF driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.
A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds support for "Debug Dump Internal Data" AQ command.
It is used to dump internal firmware or hardware data for debug
purposes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send Flow control frames if Flow
control is enabled.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
NFV use cases require the ability to steer packets to VSIs by VLAN tag
alone while being in promiscuous mode for multicast and unicast MAC
addresses. These two new functions support that ability.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds a member to the nvm_info struct for oem_ver info to be
output either by OID or ethtool.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
There are some rare cases where the release resource call will return an
admin Q timeout. In these cases the code needs to try to release the
resource again until it succeeds or it times out.
Also add little endian conversion for checksum
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Add a facility to recover the result of a previously run AQ command.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds support for AQ commands related to Tx scheduling.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add the ability to save the AdminQ write back descriptor. If the writeback
descriptor buffer was previously created, this gives it to the AQ command
request to be used to save the results.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Make sure we have the spinlocks before we clear the ARQ and ASQ management
registers. Also, widen the locked portion and make a sanity check earlier
in the send function to be sure we're working with safe register values.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
Also rework the function get_link_status to allow caller to get all
return values in the call chain bubbled back to the source, which keeps
information about failures from being lost.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Update the admin queue command header for the Fortville SW 4 Release. As
part of this release the minor FW API version number is bumped to 4 so
that the FW API version for the FVLSW4 release will now be 1.4.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Replace sprintf with i40e_debug.
Pad the line out with zeros to get to 16 bytes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The error code sent into i40e_aq_rc_to_posix() are signed values, so we
really need to treat them as such.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add status value to string decoding routines to be used in error reporting
in order to give more readable error messages rather than bare error
numbers. This decodes both the i40e_status and the AQ error codes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Due to desires to write userland drivers such as for DPDK support, and
other requests, without needing the rest of the include files, the device
ids are pulled out into a standalone file.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Seen by code review.
If dpdk is run with memory only available on a non-0 socket, then i40e pmd
refuses to initialize ports as this pmd requires some memory on socket 0.
Fix this by setting socket to SOCKET_ID_ANY, so that allocations happen on
the caller socket.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The extended SCTP flow entries are now part of the standard API.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
The extended unified packet type is now part of the standard ABI.
As mbuf struct is changed, the mbuf library version is incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
The i40e_xmit_pkts() is called, which often means HW offload is used here,
so we had better remove 'unlikely' check for checksum offload.
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Marvin Liu <yong.liu@intel.com>
Fixes issue where ieee15888 timestamping doesn't work for the i40e
pmd when RTE_ABI_NEXT is enabled.
Also refactors repeated ieee15888 flag checking and setting
code into a function.
Test report: http://dpdk.org/ml/archives/dev/2015-August/022496.html
Reported-by: Huilong Xu <huilongx.xu@intel.com>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Header buffer address for header split will be filled with the
physical address for DMA, which is actually not needed at all,
as header split hasn't been supported. Hardware requires the
least bit of header address which is 'Descriptor Done' bit when
write back should be set to 0 by driver.
The issue is that if the user wants to reserve an odd number of
bytes between the mbuf header and data buffer, the physical address
to be filled in the descriptor would happen to be odd. That means
the DD bit would be set to non-zero by driver. That will result in
reporting descriptor done wrongly.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Some drivers was not following DPDK convention and
was leaving logging always in even if LOG_LEVEL was configured
to disable debug logs.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[Thomas: apply same fix to i40e, fm10k and bnx2x]
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch fixes the issue:
Testpmd crashed with Segmentation fault when setup tx queues on vf
Steps for reproduce:
- create one vf device from i40e driver
- bind vf device to igb_uio and start testpmd
With debugging tools, we saw the struct i40e_vf is cleared after
memcpy(&dev->data->dev_conf, dev_conf, sizeof(dev->data->dev_conf)) in
rte_eth_dev_configure, which should not happen, and the pointer to
i40e_vf isn't in the range of i40e_adapter.
The root cause is the dev_private_size in i40e virtual function driver
struct rte_i40evf_pmd was set incorrectly.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Marvin Liu <yong.liu@intel.com>
I40e VF driver uses the num_queue_pairs in vf structure to construct
queue index look up table. When the nb_rx_queue is less than nb_tx_queue,
num_queue_pairs is equal to nb_tx_queue. It will make the table use
invalid queue index, then application cannot poll packets on these queues.
This patch also moves the inline function i40e_align_floor from
i40e_ethdev.c to i40e_ethdev.h.
Test report: http://dpdk.org/ml/archives/dev/2015-July/021838.html
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Due to the NIC's firmware update, the input set of sctp flow is changed
to source IP, destination IP, source port, destination port and
Verification-Tag. This patch adds the sport and dport in the programming
packet of flow director.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Marvin Liu <yong.liu@intel.com>
Add i40e_dev_free_queues() function and call it from close() functions.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
There is a segmentation fault if rxq is NULL.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
_clear_cmd() was not being called in failure situations,
resulting in the next command also failing.
Fix several typos.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch depends on the Port Hotplug Framework.
It implements the eth_dev_uninit functions for rte_i40e_pmd and
rte_i40evf_pmd.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Move malloc inside eal and create a new section in MAINTAINERS file for
Memory Allocation in EAL.
Create a dummy malloc library to avoid breaking applications that have
librte_malloc in their DT_NEEDED entries.
This is the first step towards using malloc to allocate memory directly
from memsegs. Thus, memzones would allocate memory through malloc,
allowing to free memzones.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
To unify packet types among all PMDs, bit masks of packet type for
'ol_flags' are replaced by unified packet type.
To avoid breaking ABI compatibility, all the changes would be
enabled by RTE_NEXT_ABI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
If a descriptor the device drive is handling is the context descriptor,
its type value will be 0x1.
When using the not operator ! to do the conditional check, if the expression
value is zero, the device driver will consider the transaction for this
descriptor has been completed, even its DD field is still 0x1 which means
NIC has not finished the operation on this descriptor.
Use the 0xF to check the DD status to avoid the above issue happens.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Fixes: 05999aab4c ("i40e: add or delete flow director")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Add ixgbe support for new ethdev APIs to enable and read IEEE1588/
802.1AS PTP timestamps.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
To support querying hash key size per port, an new field of
'hash_key_size' was added in 'struct rte_eth_dev_info' for storing
hash key size in bytes.
The correct hash key size in bytes should be filled into the
'struct rte_eth_dev_info', to support querying it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch extends flow director to support l2_payload flow
type in i40e driver.
Test report: http://dpdk.org/ml/archives/dev/2015-June/020238.html
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add checksum offload capability flags which have already been
supported for a long time.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
It configures specific registers to enable double vlan stripping
on RX side and insertion on TX side.
The RX descriptors will be parsed, the vlan tags and flags will be
saved to corresponding mbuf fields if vlan tag is detected.
The TX descriptors will be configured according to the
configurations in mbufs, to trigger the hardware insertion of
double vlan tags for each packets sent out.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The parameter tx_free_thresh is not consistent between the drivers:
some use it as rte_eth_tx_burst() requires, some release buffers when
the number of free descriptors drop below this value.
Let's use it as most fast-path code does, which is the latter, and update
comments throughout the code to reflect that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
It wouldn't check the configured maximum packet length, and then
the scattered receiving function wouldn't be selected at all even
if it wants to receive a jumbo frame. The fix is to select the
correct RX function according to the configurations.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
On Fedora 22, with GCC 5.1, errors are reported due to array accesses
being potentially out of bounds. This commit fixes this by adding in an
extra bounds check to the loop counter.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
To get device VMDQ info when only i40e VMDQ feature is enabled.
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Move i40e PMD to drivers/net directory.
As part of the move, rename the "i40e" directory, containing the "base
driver" code, from "i40e" to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
