Bug fix to remove (rxnfgpc - hw_stats->gprc) which does not account
for phy errors.
hw_stats->gprc is the Number of good (non-erred) Rx packets (from the
network) that pass L2 filtering and has a legal length as defined by
LongPacketEnable. While rxnfgpc is the Number of good (non-erred with
legal length) Rx packets (from the network) regardless of packet
filtering and receive enablement. Thus hw_stats->gprc can be > rxnfgpc
and this calculation should be removed from the calculation of ierrors.
Validated with testpmd by sending packets to the interface without
forwarding enabled - packets should be dropped and the error counters
incremented.
Fixes: f6bf669b99 ("ixgbe: account more Rx errors")
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Balazs Nemeth <balazs.nemeth@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Marvin Liu <yong.liu@intel.com>
ixgbe_recv_pkts_lro uses field rx_free_trigger
in structure ixgbe_rx_queue, but that field is only defined
if IXGBE_RX_ALLOW_BULK_ALLOC is enabled, so even though
that field is not used when it is disabled,
compiler complains about it.
Therefore, the lines of code that use that field
have been ifdef.
Fixes: 8eecb329 ("ixgbe: add LRO support")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Add ixgbe_dev_free_queues() function and call it from close() functions.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch depends on the Port Hotplug Framework.
It implements the eth_dev_uninit functions for rte_ixgbe_pmd and
rte_ixgbevf_pmd.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
ierrors only included a base set of error statistics, this patch adds
additional error registers to ierrors.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Add the NIC/HW specific stats that were removed from rte_ethdev.c to
the extended stats in ixgbe.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Move stats register reads to ixgbe_read_stats_registers() as it will be
used by the functions to retrieve stats and extended stats.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
add function to support ethtool ops:
- get_reg_length
- get_regs
- get_eeprom_length
- get_eeprom
- set_eeprom
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
- set_mac_addr
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Move malloc inside eal and create a new section in MAINTAINERS file for
Memory Allocation in EAL.
Create a dummy malloc library to avoid breaking applications that have
librte_malloc in their DT_NEEDED entries.
This is the first step towards using malloc to allocate memory directly
from memsegs. Thus, memzones would allocate memory through malloc,
allowing to free memzones.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
To unify packet type among all PMDs, bit masks of packet type for
'ol_flags' are replaced by unified packet type.
To avoid breaking ABI compatibility, all the changes would be
enabled by RTE_NEXT_ABI.
Note that around 2.5% performance drop (64B) was observed of doing
4 ports (1 port per 82599 card) IO forwarding on the same SNB core.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
In order to unify the packet type, the field of 'packet_type' in
'struct rte_mbuf' needs to be extended from 16 to 32 bits.
Accordingly, some fields in 'struct rte_mbuf' are re-organized to support
this change for Vector PMD.
As 'struct rte_kni_mbuf' for KNI should be right mapped to
'struct rte_mbuf', it should be modified accordingly.
In ixgbe PMD driver, corresponding changes are added for the mbuf changes,
especially the bit masks of packet type for 'ol_flags' are replaced by
unified packet type. In addition, more packet types (UDP, TCP and SCTP)
are supported in vectorized ixgbe PMD.
To avoid breaking ABI compatibility, all the changes would be enabled by
RTE_NEXT_ABI.
Note that around 2% performance drop (64B) was observed of doing 4 ports
(1 port per 82599 card) IO forwarding on the same SNB core.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
There's a parameter "autoneg on|off" in testpmd CLI "set flow_ctrl ...". This
parameter is used to enable/disable auto negotiation for flow control. But it's
not supported yet.
The auto negotiation is enabled by default, we have no way to disable it. This
patch lets the parameter "autoneg on|off" be supproted.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
When initialize the hardware, the stat should be reset.
Otherwise when detach then attach port, the stat will not
be re-init to zero.
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Add ixgbe support for new ethdev APIs to enable and read IEEE1588
PTP timestamps.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
To support querying hash key size per port, an new field of
'hash_key_size' was added in 'struct rte_eth_dev_info' for storing
hash key size in bytes.
The correct hash key size in bytes should be filled into the
'struct rte_eth_dev_info', to support querying it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This path renames the mirror type in rte_eth_mirror_conf and macros,
and rework the mirror set in ixgbe drivers by using new definition.
It also fixes some coding style.
Test report: http://dpdk.org/ml/archives/dev/2015-June/019118.html
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Rename rte_eth_vmdq_mirror_conf to rte_eth_mirror_conf and move
the maximum rule id check from ethdev level to driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Little endian to CPU order conversion had been added for reading
vlan tag from RX descriptor, while its original source line was
forgotten to delete. That's a discarded source line and should be
deleted.
Fixes: 23fcffe8ff ("ixgbe: fix id and hash with flow director")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The parameter tx_free_thresh is not consistent between the drivers:
some use it as rte_eth_tx_burst() requires, some release buffers when
the number of free descriptors drop below this value.
Let's use it as most fast-path code does, which is the latter, and update
comments throughout the code to reflect that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The function to clear the TX ring when a port was being closed, e.g. on
exit in testpmd, was not checking the mbuf refcnt before freeing it.
Since the function in the vector driver to clear the ring after TX does
not set the pointer to NULL post-free, this caused crashes if mbuf
debugging was turned on.
To reproduce the issue, ensure the follow config variables are set:
RTE_IXGBE_INC_VECTOR
RTE_LIBRTE_MBUF_DEBUG
Then compile up and run testpmd using 10G ports with the vector driver.
Start traffic and let some flow through, then type "stop" and "quit" at
the testpmd prompt, and crash will occur. Output below:
testpmd> quit
Stopping port 0...done
Stopping port 1...PANIC in rte_mbuf_sanity_check():
bad ref cnt
[New Thread 0x7fffabfff700 (LWP 145312)]
[New Thread 0x7fffb47fe700 (LWP 145311)]
[New Thread 0x7fffb4fff700 (LWP 145310)]
[New Thread 0x7ffff6cd5700 (LWP 145309)]
18: [/home/bruce/dpdk.org/x86_64-native-linuxapp-gcc/app/testpmd(_start+0x29)
<....snip for brevity...>
Program received signal SIGABRT, Aborted.
0x00007ffff7120a98 in raise () from /lib64/libc.so.6
A similar error occurs when clearing the RX ring, which is also fixed by
this patch.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
As well as the fast-path functions in the rxtx code, there are also
functions which set up and tear down the descriptor rings. Since these
are not performance critical functions, there is no need to have them
extensively optimized, so we add __attribute__((cold)) to their
definitions. This has the side-effect of making debugging them easier as
the compiler does not optimize them as heavily, so more variables are
accessible by default in gdb.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This patch adds max_link_up_time parameter to mac structure.
This parameter is used to control maximum link polling time in
ixgbe_check_mac_link functions. It is required to prevent long wait
time on x550 PHY that have no external link.
Since x550 is handled by software, we have to reset internal (PHY to
PHY) link when external link changes, and after reset, we have to wait for
this link to be established. As a result of not having interrupts, we have
to poll for link state, and we know that this link comes up much faster
than default 9 seconds. This parameter is added to prevent waiting 9
seconds for link when external link is not established.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Since this 82599 device supports WoL(Wake on LAN), driver needs
a define for the sub device ID.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds support for new x550 PHY IDs:
0x0154 0x0223
0x0154 0x0221
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add new values that vary by MAC type that are introduced in
x540, x550.
And remove some meaningless comments BTW.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a const u32 *mvals pointer to the ixgbe_hw struct to point to an
array of mac-type-dependent values. These can include register
offsets, masks, whatever can be in a u32. When the ixgbe_hw struct
is initialized, a pointer to the appropriate array must be set.
The IXGBE_I2CCTL register references are changed to use it.
Use the mvals array to hold differing values used for
IXGBE_I2C_* symbols.
Use the mvals array to hold differing values used for
IXGBE_*_GPI* symbols.
Use the mvals array to hold differing values use for CIAA and
CIAD symbols.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
According to the hardware, the LINE side of the cs4227 needs to be
set to 10 Gbps SR mode regardless of the configuration of the link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The code in the if statement is specific to the KR PHY. However,
the conditional was only checking for backplane. If the driver
was using the KX4 backplane PHY, this code would execute but
would write to the wrong PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch disables SW LPLU on x557 V2. It also sets the
enter_lplu function pointer to NULL on x557 V2. LPLU will be
implemented in FW for all x557 V2 interfaces. The SW LPLU
implementation must be disabled on V2 to avoid conflicts with
FW. SW LPLU support is still required for x557 V1.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch implements ixgbe_led_on_t_X550em and ixgbe_led_off_t_X550em
function for turning on and off LEDs on X557 external PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The MDIO clock needs to be configured for a specific speed for
x550em. We expected this to be done automatically, but in
the early days of the project this was not happening. We put
code in to do this ourselves.
Eventually, we decided that there is no harm in having SW do
this all the time, so we may not remove this code in the future.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Ensure link is still up after getting the speed, to ensure that the
speed read is valid.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch removes the clearing of the FEC(Forward Error Correction)
bits in ixgbe_setup_kr_speed_x550em. FEC default enablement is
configured via the NVM and SW should not be overriding these defaults
in this function.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds support for x550em KR/iXFI internal link modes. The initial
x550em-10GBASET and x550em-SFP designs use iXFI internal link mode between
the internal PHY and the external PHY.
However future designs will use a KR internal link. This patch is intended
to future proof the driver by adding the KR internal link support in the
driver now.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
EEE(Energy Efficient Ethernet) is not supported on the initial revision
of IXGBE_DEV_ID_X550EM_X_KR. We determine the revision by reading a fuse
register.
Also, the requirements for FEC(Forward Error Correction) have changed
slightly. Now, we don't change the "request" bit at all. When EEE is
enabled, we advertise that we are capable. When EEE is disabled, we do
not advertise that we are capable. This change makes us consistent with
the power-on defaults that are in the NVM.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC(Forward Error Correction) feature had been disabled
because it increases power consumption. However, some customers
want to use it. This patch enables FEC when EEE(Energy Efficient
Ethernet) is disabled; FEC was already being disabled when EEE
was enabled, but now both are done in the same function. The two
features are not allowed to be enabled at the same time. The two
features cannot both be disabled. If this ability is ever
determined to be needed, we will need to define a new user parameter
to control FEC independently of EEE.
Fixes: d4c9ffd4fe ("ixgbe/base: disable X550em FEC to save power")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
During init, check the ucode running in the CS4227. If
it is not responding correctly, reset the part. This is
a global reset so it must only be done the first time a
driver loads after power-on.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Because each IOSF access requires the use of multiple registers,
use a semaphore to serialize those accesses.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a helper function to wait for IOSF accesses to complete. Also
perform this wait before each access, as specified in the datasheet.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
x550em has two different bus speeds, 300 MHz and 400 MHz.
A bit in a fuse register tells which it is, with a 1 meaning
the bus is running at 300 MHz.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
In UniPHY we have 2 IOSF targets that are UniPHY related. We can
write to PHY and PCS. In earlier times I've been told that there
were 2 separate PCS targets for IOSF commands and that's why I
implemented it with 2 defines and adding hw->bus.lan_id, but lately
I confirmed with HW that FW takes care of which PCS "slice" we are
talking to and is directing writes to correct one, so KX4_PCS1
target is dead now and we cannot use it.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch powers down the x550em PHY on over-temp events. The
PHY firmware is supposed to do this autonomously but that isn't
implemented. The short-term stop-gap solution is for SW to power
down the PHY when it reports an overtemp event.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds identify SFP module support for x550em. x550em
support returns an error for SFP module types not supported by
x550em design.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch updates the x550em SFP link setup by adding
ixgbe_sfp_type_unknown and ixgbe_sfp_type_not_present case expression
to the ixgbe_setup_mac_link_sfp_x550em SFP type switch statement. This
handles the case when no module is present.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Fix the warning caused by an uninitialized variable which might have
been used.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Configure the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the 82599 flow.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On systems that support LPLU in the firmware, the driver wouldn't be
aware of the LPLU speed change, and it wouldn't cache the new value when
the driver resumes. This patch emulates the same behavior by restoring
the previous autoneg settings to autoneg_advertised.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch updates x550em LPLU (Low Power Link Up) to use the
MAC ops setup_link function pointer.
This removes redundant code and provides iXFI and KR support
between internal and external PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Because we acquire two semaphore bits before setting the SWFW_SYNC
register, we should release them in the reverse order that they
were acquired.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. The PCI transactions pending bit sticks high
when there were pending transactions, we should wait and then continue
with our reset flow.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch fixes comment description for setting 2.5G and 5G speeds in
ixgbe_setup_phy_link_generic.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Adds define for the number of bits needed to shift the EEE_SU register
in order to get the value of TEEE_DLY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This path changes ((P == 0) ? (<value for port 0>) : (<value for port 1>))
register definition into ((P) ? <value for port 1> : <value for port 0>)
style.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Update readme file to show the version of the base code.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For there're only laser ports on x550 before, we only considered laser
ports for the testpmd CLIs "port start/stop ...". Now we have new x550
devices which have copper ports. Use the API for copper to enable/disable
these ports.
And also let the testpmd CLI "set link-up/down ..." support copper
ports.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
When TSO is used with IPv6, generated frames are incorrect.
L4 frame is OK, but length field of IPv6 header was not populated correctly.
IXGBE_ADVTXD_TUCMD_IPV6 flag is set for better readability, even if it
does nothing.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Current ixgbe VF base driver only really read the status register when:
- get_link_status is true
- link reset
- mailbox timeout.
We only set get_link_status to true when we start the PF/VF, so
following calls to ixgbe_dev_link_update will just keep the old link
status unless the link has been reset.
Because of this behaviour, when the link status of the PF changes after
the VF has been initialized, we do not read the current status register
from the nic and instead we just keep the old link status.
Fix the problem by setting this field to true before calling
ixgbe_check_link function from base driver. We don't need to check after
this call for get_link_status anymore, so remove it.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
The logic to select ixgbe VF RX function is different than PF side.
There are a few issues with its current state:
- it does not allow to select ixgbe_recv_pkts_vec among other options.
- it can cause memory corruption for scatter mode as it does not allocate
enough entries in sw_ring.
- when checksum is enabled, incorrect vector RX function is selected.
To solve above issues, change the VF RX function selection logic to
mimic PF side.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The flexbytes offset can not be set, because the value is over written
when fdir is enabled.
This patch fixes this issue, and also removes some reduplicate lines.
Fixes: d54a988826 ("ixgbe: support flexpayload configuration of flow director")
Reported-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: David Marchand <david.marchand@6wind.com>
On x550, flow director doesn't support other IP packets directly.
If we want to monitor IP other packets, the L4 protocol and ports must
be masked. It means, on x550, if we want to add a flow director filter
for other IP packets, a flow director mask must have been configed to
mask L4 protocol and ports.
Return err when the user try to config a flow director filter for other
IP packets without flow director mask configed before. And print err log
for it.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch sets the setup_EEE function pointer to NULL for the
interfaces which do not support EEE (Energy Efficient Ethernet).
Currently only the KR backplane interface (0x15AB) supports EEE.
Setting this pointer to NULL prevents EEE registers from being
incorrectly modified and gives base drivers a flag to check for
EEE support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em PHY reset function ixgbe_reset_phy_t_X550em.
ixgbe_reset_phy_t_X550em calls the reset PHY generic, and then enables
the x550em PHY LASI(Link Alarm Status Interrupt) interrupts.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Set the lan_id before the first I2C access. The existing call was
clearly being done after a previous I2C access in the same function
and that can't be right, so call the set_lan_id method earlier. At
this point it probably doesn't matter for this QSFP function, but
it makes sense to do it consistently anyway.
On X550, be sure to set the lan_id before using it to configure the
mux control output, else the mux will not be controlled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The introduction of ixgbe_get_bus_info_X550em failed to call the
set_lan_id method to set the func and lan_id and deal with port-
swapped configurations. Add the call to resolve the problem.
Fixes: 4cf0bb32a9 ("ixgbe/base: get X550 bus info")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking x550em
PHY link. We check that both the MAC and external x550em PHY have link.
This is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em external PHY interrupt and forced 1G/10G
support. Support includes enabling and handling Link Status
Change and Thermal Sensor interrupt. ixgbe_handle_lasi has been added
to the API for handling the interrupts received from x550em PHY.
ixgbe_enable_lasi_ext_t_x550em and ixgbe_get_lasi_ext_t_x550em have been
added to X550em to enable mask and check interrupt flags for x550em PHY.
Forced 1G/10G link speed is handled via ixgbe_setup_mac_link_t_X550em.
ixgbe_setup_mac_link_t_X550em sets up the internal PHY and
external PHY link to either 10G or 1G based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em Auto neg Flow Control support to
ixgbe_device_supports_autoneg_fc and sets the x550em setup_fc function
pointer to ixgbe_setup_fc_generic. ixgbe_setup_fc_generic is used for
x550em because flow control is setup on the external PHY via MDIO, when
ixgbe_setup_fc_X550em sets up flow control on the internal PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch cleans up the ixgbe_setup_internal_phy_ x550em() function as follows:
- Renames it to ixgbe_setup_internal_phy_t_x550em to clarify that it is
specific to copper
- Returns an error if called for non-copper devices
- Corrects the comments
- Removed the LASI(Link Alarm Status Interrupt) status register checks as
this was incorrect and never worked correctly anyway.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch changes the return value for ixgbe_setup_internal_phy_t_x550em
when link is down to IXGBE_SUCCESS.
The driver will call ixgbe_setup_internal_phy_t_x550em when a link status
change is reported. The links status change can occur on link up or link
down, and if the link status change is for link down then there is no iXFI
setup necessary and no error condition needs to be returned.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The following patch moves the handling of the I2C MUX (which is only
used for x550em SFP+ devices) out of the ixgbe_x540.c file and
into the ixgbe_x550.c file where it belongs.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The init flow is simplified. We no longer wait for the PHY FW init
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be "un-stalled". SW no longer needs to put the PHY in
low-power mode or enable the transceiver.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For the KR backplane which is different from other backplane,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SW Low Power Link Up (LPLU) support for x550em PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SFP+ dual-speed support.
82599 fiber link code was moved from ixgbe_82599.c to ixgbe_commom.c
for use by X550em, and the API was updated to support the common code
usage. SFP MAC link code is added to x550em.
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC (Forward Error Correction) feature can improve BER (Bit Error Rate)
but uses more power to do so. It also cannot be used with
EEE (Energy Efficient Ethernet).
EEE is an important feature, and we have no known BER issues, so FEC
is not needed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. So,
put the code in a function so it can be used in more than one place.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The driver now needs to issue a firmware command to inform the
firmware that a driver is coming up. This prevents the possibility
of the firmware and the driver configuring the PHY at the same
time. Upon completion of the command, the firmware will no longer
be configuring the PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
A retry count of 10 is likely to run into problems on X550 devices
that have to detect and reset unresponsive CS4227 devices. So,
reduce the I2C retry count to 3 for X550 and above. This should
avoid any possible regressions in existing devices.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Most I2C accesses take and release semaphores for each access. It's
also necessary to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
All bits in FDIRTCPM and FDIRUDPM are set to 1 when
ixgbe_fdir_set_input_mask_82599 is called. Not settings these bits will cause
TCP and UDP packets to be filtered out when NVGRE or VXLAN mode is enabled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch moves the check of the return value from
ixgbe_start_hw_generic after the function is called.
Previously we had the code to disable relaxed ordering in
between, which seems a bit out of place.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Remove the redundant "from".
There's a typo in the code comment for FC end
of Frame Exception (FCEOFe/IPE), so fixed the typo.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move ixgbe PMD to drivers/net directory.
As part of the move, we rename the ixgbe directory, containing the
ixgbe "base driver" code, from "ixgbe" to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
