The device-specific metadata was stored in the deprecated field udata64.
It is moved to a dynamic mbuf field in order to allow removal of udata64.
The name rte_security_dynfield is not very descriptive
but it should be replaced later by separate fields for each type of data
that drivers pass to the upper layer.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Adding support for VLAN based RSS hash. Two bytes of TCI field
will be considered for hashing.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Scatter gather mode should get enabled:
- If mbuf size is less than max received packet length.
- MTU is reconfigured greater than mbuf size.
Fixes: 0e2efd02db58 ("net/octeontx2: add MTU set operation")
Cc: stable@dpdk.org
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add device arguments to lock Rx/Tx contexts.
Application can either choose to lock Rx or Tx contexts by using
'lock_rx_ctx' or 'lock_tx_ctx' respectively per each port.
Example:
-w 0002:02:00.0,lock_rx_ctx=1 -w 0002:03:00.0,lock_tx_ctx=1
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Andrzej Ostruszka <aostruszka@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Issue has been observed where packets are getting dropped
at DMAC filtering if a new dmac address is added before
starting of port.
Fixes: c43adf61682f ("net/octeontx2: add unicast MAC filter")
Cc: stable@dpdk.org
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Sunil Kumar Kori <skori@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
When an application invokes rte_eth_dev_configure consecutively without
setting up Rx/Tx queues, it will incorrectly return error while trying
to restore Rx/Tx queue configuration.
Fix configuration sequence by checking if any Rx/Tx queues are
previously configured before trying to restore them.
Fixes: 548b5839a32b ("net/octeontx2: add device configure operation")
Cc: stable@dpdk.org
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add debug support to TM to dump configured topology
and registers. Also enable debug dump when sq flush fails.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Modify resource allocation and freeing logic to support
dynamic topology commit while to traffic is flowing.
This patch also modifies SQ flush to timeout based on minimum shaper
rate configured. SQ flush is further split to pre/post
functions to adhere to HW spec of 96XX C0.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Configure NIX_AF_TL3_TL2X_LINKX_CFG using schq at
level based on NIX_AF_PSE_CHANNEL_LEVEL[BP_LEVEL].
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding support to configure link attributes like speed,
duplex, negotiation.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Patch adds routines to set/clear nix lf error & ras interrupt enable
registers. These nix lf error interrupts get triggered if there are
any failures during nix lf configuration. This interrupts are enabled
before any hardware configurations initiated on the allocated nix lf.
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Acked-by: Andrzej Ostruszka <aostruszka@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Currently when application requests for RTE_FC_NONE earlier
than PMD's internal fc mode update, flow control set routine
is returning without updating the flow control state.
Patch updates the PMD's internal fc mode details during
dev_configure to ensure any flow control set requests
issued later are handled properly.
Fixes: 609945f1ce90 ("net/octeontx2: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Before C0 HW revision, The RSS adder was computed based the following
static formula.
rss_adder<7:0> = flow_tag<7:0> ^ flow_tag<15:8> ^
flow_tag<23:16> ^ flow_tag<31:24>
The above scheme has the following drawbacks:
1) It is not in line with other standard NIC behavior.
2) There can be an SW use case where SW can compute the hash
upfront using Toeplitz function and predict the queue selection
to optimize some packet lookup function. The nonstandard
way of doing XOR makes the consumer to not predict the queue selection.
C0 HW revision onward, The HW can configure the
rss_adder<7:0> as flow_tag<7:0> to align with standard NICs.
This patch adds an option to select legacy RSS adder mode
using tag_as_xor=1 devargs option while keeping the standard NIC
behavior as default.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Extend RSS offload types for octeontx2. Add support to select
L3 SRC, L3 DST, L4 SRC and L4 DST for RSS calculation.
Add support to select L3 SRC or DST only, L4 SRC or DST only for RSS
calculation.
With this requirement there will be following combinations,
IPV[4,6]_SRC_ONLY, IPV[4,6]_DST_ONLY, [TCP,UDP,SCTP]_SRC_ONLY,
[TCP,UDP,SCTP]_DST_ONLY. So, instead of creating a bit for each
combination, we are using upper 4 bits (31:28) in the flow_key_cfg
to represent the SRC, DST selection. 31 => L3_SRC, 30 => L3_DST,
29 => L4_SRC, 28 => L4_DST. These won't be part of flow_cfg, so that
we don't need to change the existing ABI.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Use new marker typedef available in EAL.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Reviewed-by: Gavin Hu <gavin.hu@arm.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Avoid using PCI subsystem device id for SoC revision
identification and just use PCI revision id to support C0 silicon.
This patch also reduces SQB threshold to 70% to have
sufficient buffer before we overflow SQ.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Enable packet type parsing by default, only disable when
`rte_eth_dev_set_ptypes()` is called with ptype_mask as 0.
This would enable applications that are dependent on packet type parsing
like l3fwd.
Also this patch preserves configuration set by `rte_eth_dev_set_ptypes`
across multiple calls of `rte_eth_dev_configure()`
Fixes: d2706e15e6fb ("net/octeontx2: support reduced set of packet types")
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add support to set supported ptypes for octeontx2 and
remove devarg scheme to disable ptype parsing support as
application can use rte_eth_dev_set_ptypes() normative API
to enable the same use case.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Issue has been observed if PTP is already enabled on PF and
later VFs are configured. Since PTP requires mbuf data off
to be shifted by 8 bytes, due to this l3fwd/l2fwd was not
working with VFs.
Also some extra garbage bytes were observed in packet data
when ptp was enabled.
Fixes: b5dc3140448e ("net/octeontx2: support base PTP")
Cc: stable@dpdk.org
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Retrieve burst mode information according to the selected Rx/Tx mode and
offloads.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add DEV_RX_OFFLOAD_RSS_HASH flag for all PMDs that support RSS hash
delivery.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
System DPI Packet Interface Unit (SDP) is a co-processor
of OCTEON TX2 which provides PCIe endpoint support for a
remote host to DMA packets into and out of the OCTEON TX2 SoC.
SDP interface comes in to live only when it is connected in
EP mode. It exposes input and output queue pairs to remote host
for instruction input and packet output. It can be used as
a communication channel between remote host and OCTEON TX2.
Host machine needs to use corresponding user/kernel mode
driver to communicate with SDP interface on OCTEON TX2 SoC.
SDP interface support is limited to SDP PF device now.
No SDP VF support.
Signed-off-by: Subrahmanyam Nilla <snilla@marvell.com>
Signed-off-by: Venkateshwarlu Nalla <venkatn@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add support to below TCP segmentation offloads for
96XX A1 onwards and 95xx B0 onwards.
- TCPv4, TCPv6
- VXLAN[v4 | v6][v4 | v6]
- GENEVE[v4 | v6][v4 | v6]
This patch also modifies a fastpath function to be forced
inline due to performance reasons for multi-seg mode.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Adding support for tx descriptor status dev ops for octeontx2.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Enabling/disabling of allmulticast mode is not always successful and
it should be taken into account to be able to handle it properly.
When correct return status is unclear from driver code, -EAGAIN is used.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Change return value of the callbacks from void to int. Make
implementations across all drivers return negative errno
values in case of error conditions.
Both callbacks are updated together because a large number of
drivers assign the same function to both callbacks.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Enabling/disabling of promiscuous mode is not always successful and
it should be taken into account to be able to handle it properly.
When correct return status is unclear from driver code, -EAGAIN is used.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Matan Azrad <matan@mellanox.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Change eth_dev_infos_get_t return value from void to int.
Make eth_dev_infos_get_t implementations across all drivers to return
negative errno values if case of error conditions.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Update workaround changes for erratas that are fixed on 96xx A1.
This patch also enables cq drop for all the passes for
maintaining performance along with updating a default
Rx ring size in dev_info.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Patch extends minimum supported max_sqb_count devarg value
such that it can limit the max sqb count to 8 buffers and
also defines NIX_DEF_SQB and uses it to compute the number
of sqe buffers required for the egress traffic.
NIX_DEF_SQB is defined as 16 which is optimal across multiple
octeontx2 platforms to scale up the performance proportional
to the corresponding port/queue to lcore mappings.
Fixes: fb0198b7dc07 ("net/octeontx2: add devargs parsing functions")
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
This patch implements read clock api whose purpose is to return
raw clock ticks. Using this API real time ticks spent in
processing a packet can be known:
<read_clock val at any time> - mbuf->timestamp
Calling mbox for reading raw clock ticks in fastpath is very
expensive so its value is derived from time stamp counter(tsc)
using freq multiplier (ratio of raw clock ticks and tsc) and clock
delta (by how much tsc is lagging from raw clock value).
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add support for setting the link up and down.
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
This patch implements rx interrupts feature required for power
saving. These interrupts can be enabled/disabled on demand.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add MTU set operation and MTU update feature.
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Implement support for setting VLAN TPID and PVID for Tx packets.
Signed-off-by: Vivek Sharma <viveksharma@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Support setting up VLAN filters so as to allow tagged
packet's reception after VLAN HW Filter offload is enabled.
Signed-off-by: Vivek Sharma <viveksharma@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Support configuring VLAN offloads for an ethernet device and
dynamic promiscuous mode configuration for VLAN filters where
filters are updated according to promiscuous mode of the device.
Signed-off-by: Vivek Sharma <viveksharma@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
First pass rte_flow utility functions for octeontx2.
These will be used to communicate with AF driver.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Vivek Sharma <viveksharma@marvell.com>
Add remaining PTP configuration/slowpath operations.
Timesync feature is available only for PF devices.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Zyta Szpak <zyta@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
