Ixgbe HW supports 128 TX queues. However, the full 128 queues are only
available in VT and DCB mode. In normal default "none" mode (VT/DCB off)
the maximum number of available queues is only 64.
The driver doesn't check the mode when reporting the available
number of queues, allowing more that 64 queues to be used in all cases.
If a queue no. >=64 is used in default mode, the TX packets will be dropped
silently.
This change adds a check to forbid using a queue number larger than 64
during device configuration (in default mode), so that the problem is
reported as early as possible.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch extends the commands for changing flow director filter's input
set. It adds vlan as a possible filter input field.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch extends flow director to select vlan id as part of
filter's input set and program the filter rule with vlan id.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch extends commands for changing a flow director filter's input
set. It adds tos, protocol and ttl as filter's input fields, and removes
the words selection from flex payloads.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds RTE_ETH_INPUT_SET_L3_IP4_TTL,
RTE_ETH_INPUT_SET_L3_IP6_HOP_LIMITS input field types and extends
struct rte_eth_ipv4_flow and rte_eth_ipv6_flow to support filtering
by tos, protocol and ttl.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
VLAN insertion can be done in hardware when supported in Verbs. A software
fallback is provided otherwise. The software implementation is also used
when multi-packet send is enabled on a queue, as both features are mutually
exclusive.
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Environment variable MLX5_PMD_ENABLE_PADDING enables HW packet padding
in PCI bus transactions.
When packet size is cache aligned and CRC stripping is enabled, 4 fewer
bytes are written to the PCI bus. Enabling padding makes such packets
aligned again.
In cases where PCI bandwidth is the bottleneck, padding can improve
performance by 10%.
This is disabled by default since this can also decrease performance for
unaligned packet sizes.
Signed-off-by: Olga Shern <olgas@mellanox.com>
fix packet padding macro check
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Secondary processes are expected to use queues and other resources
allocated by the primary, however Verbs resources can only be shared
between processes when inherited through fork().
This limitation can be worked around for TX by configuring separate queues
from secondary processes.
Signed-off-by: Or Ami <ora@mellanox.com>
Add driver functions to set link state up or down.
Burst functions are updated to make sure applications cannot attempt to
send/receive after link is brought down.
Signed-off-by: Or Ami <ora@mellanox.com>
When Linux PF and DPDK VF are used for i40e PMD, when a PF reset occurs,
an interrupt will go via adminq event to inform the VF of the reset.
A callback mechanism is introduced for the VF to allow it to invoke a
registered callback when PF reset happens.
Users can register a callback for this interrupt event using:
rte_eth_dev_callback_register(portid,
RTE_ETH_EVENT_INTR_RESET,
reset_event_callback,
arg);
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The patch introduces a new PMD. This PMD is implemented as thin wrapper
of librte_vhost. It means librte_vhost is also needed to compile the PMD.
The vhost messages will be handled only when a port is started. So start
a port first, then invoke QEMU.
The PMD has 2 parameters.
- iface: The parameter is used to specify a path to connect to a
virtio-net device.
- queues: The parameter is used to specify the number of the queues
virtio-net device has.
(Default: 1)
Here is an example.
$ ./testpmd -c f -n 4 --vdev 'eth_vhost0,iface=/tmp/sock0,queues=1' -- -i
To connect above testpmd, here is qemu command example.
$ qemu-system-x86_64 \
<snip>
-chardev socket,id=chr0,path=/tmp/sock0 \
-netdev vhost-user,id=net0,chardev=chr0,vhostforce,queues=1 \
-device virtio-net-pci,netdev=net0,mq=on
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Rich Lane <rich.lane@bigswitch.com>
Tested-by: Rich Lane <rich.lane@bigswitch.com>
Update for queue state event name:
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This is a PMD for the Amazon ethernet ENA (Elastic Network Adapters)
family.
The driver operates variety of ENA adapters through feature negotiation
with the adapter and upgradable commands set.
ENA driver handles PCI Physical and Virtual ENA functions.
Signed-off-by: Evgeny Schemeilin <evgenys@amazon.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Release Note addition:
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This patch implements PQoS as a sample application.
PQoS allows management of the CPUs last level cache,
which can be useful for DPDK to ensure quality of service.
The sample app links against the existing 01.org PQoS library
(https://github.com/01org/intel-cmt-cat).
White paper demonstrating example use case "Increasing Platform Determinism
with Platform Quality of Service for the Data Plane Development Kit"
(http://www.intel.com/content/www/us/en/communications/increasing-platform-determinism-pqos-dpdk-white-paper.html)
Signed-off-by: Wojciech Andralojc <wojciechx.andralojc@intel.com>
Signed-off-by: Tomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: Marcel D Cornu <marcel.d.cornu@intel.com>
This patch updates the release notes with the features that
have been added to ip_pipeline application.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Allow dynamic deallocation of af_packet device through proper
API functions. To achieve this:
* set device flag to RTE_ETH_DEV_DETACHABLE
* implement rte_pmd_af_packet_devuninit() and expose it
through rte_driver.uninit()
* copy device name to ethdev->data to make discoverable with
rte_eth_dev_allocated()
Moreover, make af_packet init function static, as there is no
reason to keep it public.
Signed-off-by: Wojciech Zmuda <woz@semihalf.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Add support for linking multi-segment buffers together to
handle Jumbo packets. The vmxnet3 API supports having header
and body buffer types. What this patch does is fill the primary
ring completely with header buffers and the secondary ring
with body buffers. This allows for non-jumbo frames to only
use one mbuf (from primary ring); and jumbo frames will have
first mbuf from primary ring and following mbufs from other
ring.
This could be optimized in future if the DPDK had API
to supply different sized mbufs (two pools) into driver.
Signed-off-by: Stephen Hemminger <shemming@brocade.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Release note addition:
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This commit adds vmxnet3 TSO support.
Verified with test-pmd (set fwd csum) that both tso and
non-tso pkts can be successfully transmitted and all
segmentes for a tso pkt are correct on the receiver side.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Tx data ring support was removed in a previous change that
added multi-seg transmit. This change adds it back.
According to the original commit (2e849373), 64B pkt
rate with l2fwd improved by ~20% on an Ivy Bridge
server at which point we start to hit some bottleneck
on the rx side.
I also re-did the same test on a different setup (Haswell
processor, ~2.3GHz clock rate) on top of the master
and still observed ~17% performance gains.
Fixes: 7ba5de417e ("vmxnet3: support multi-segment transmit")
Signed-off-by: Yong Wang <yongwang@vmware.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Mmap PCI resource file and add inline functions for reading from and
writing to PCI resource address space.
Add description of IBUF and OBUF address space.
Add configuration option for setting which firmware type will be used.
Right address space values for IBUFs and OBUFs offsets are used
according to configuration option CONFIG_RTE_LIBRTE_PMD_SZEDATA2_AS.
Setting link up/down and getting info about link status is done through
mmapped PCI resource address space.
Signed-off-by: Matej Vido <vido@cesnet.cz>
PMD was of type PMD_VDEV which means that PCI device is not recognised
automatically during EAL initialization, but it has to be created by
EAL option --vdev.
Now, PMD is of type PMD_PDEV which means that PCI device is probed
and recognised during EAL initialization automatically.
Path to szedata2 device file is matched with device and the count
of available RX and TX DMA channels is found out during device
initialization.
Initialization, starting and stopping of queues is changed to better
correspond with Ethernet device API model. Function callbacks
(rx|tx)_queue_(start|stop) are added. Unnecessary items are removed
from ethernet device private data structure.
Signed-off-by: Matej Vido <vido@cesnet.cz>
Change rxq_cq_to_ol_flags() to set checksum flags according to packet type,
so for non L3/L4 packets the mbuf chksum_bad flags will not be set.
Fixes: 67fa62bc67 ("mlx5: support checksum offload")
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
RSS configuration should not be freed when priv is NULL.
Fixes: 2f97422e77 ("mlx5: support RSS hash update and get")
Signed-off-by: Or Ami <ora@mellanox.com>
Allows HW to strip the 802.1Q header from incoming frames and report it
through the mbuf structure.
This feature requires MLNX_OFED >= 3.2.
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This patch enables reading sglort (global resource tag) info into the
mbuf for RX and inserting an FTAG (Fabric Tag) at the beginning of the
packet for TX. The vlan_tci_outer field selected from rte_mbuf structure
for sglort is not used in fm10k now.
In FTAG based forwarding mode, the switch will forward packets according
to glort info in FTAG rather than mac and vlan table.
To activate this feature, user needs to pass a devargs parameter to eal
for fm10k device like "-w 0000:84:00.0,enable_ftag=1". Currently this
feature is supported only on PF, because FM10K_PFVTCTL register is
read-only for VF.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Using SSE instructions to parse error flags in HW Rx descriptor,
then set corresponding bits of mbuf.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
When the TX function tries to free a bunch of mbufs, it will free
them one by one. This change will scan the free list and merge the
requests in case they belongs to same pool, then free once, which
will reduce cycles on freeing mbufs.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Previous l3fwd-power only processes IP and IPv6 packets, other
packets' mbufs are not freed, and this causes a memory leak.
This patch fixes this issue.
Fixes: 3c0184cc0c ("examples: replace some offload flags with packet type")
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
In interrupt mode, each rx queue can have one interrupt to notify the
application when packets are available in that queue. Some queues
also can share one interrupt.
Currently, fm10k needs one separate interrupt for mailbox. So, only those
drivers which support multiple interrupt vectors e.g. vfio-pci can work
in fm10k interrupt mode.
This patch uses the RXINT/INT_MAP registers to map interrupt causes
(rx queue and other events) to vectors, and enable these interrupts
through kernel drivers like vfio-pci.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
This patch implemented the ops of adding and removing mac
address in i40evf driver. Functions are assigned like:
.mac_addr_add = i40evf_add_mac_addr,
.mac_addr_remove = i40evf_del_mac_addr,
To support multiple mac addresses setting, this patch also
extended the mac addresses adding and deletion when device
start and stop. Each VF can have a maximum of 64 mac
addresses.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
VEB switching feature for i40e is used to enable the switching between the
VSIs connect to the virtual bridge. The old implementation is setting the
virtual bridge mode as VEPA which is port aggregation. Enable the switching
ability by setting the loop back mode for the specific VSIs which connect
to PF or VFs.
VEB/VSI/VEPA are concepts not specific to the i40e HW, the concepts are
from 802.1qbg spec
IEEE EVB tutorial:
http://www.ieee802.org/802_tutorials/2009-11/evb-tutorial-draft-20091116_v09.pdf
VEB: a virtual switch can forward the packet based on the specific match
field.
VSI: a virtual interface connect between the VEB/VEPA and virtual machine.
VEPA: a virtual Ethernet port aggregator will upstream the packets from
VSI to the LAN port.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Currently, the example vmdq_dcb only works on Intel(R) 82599 NICs.
This patch extends this sample to make it work both on Intel(R) 82599
and X710/XL710 NICs by making the following changes:
1. add VMDQ base queue checking to avoid forwarding on PF queues.
2. assign each VMDQ pool to a MAC address.
3. add more arguments (nb-tcs, enable-rss) to change the default
setting
4. extend the max number of queues from 128 to 1024.
This patch also reworks the user guide for the vmdq_dcb sample.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Previously, DCB(Data Center Bridging) is only enabled on PF,
queue mapping and BW configuration is only done on PF.
This patch enables DCB for VMDQ VSIs(Virtual Station Interfaces)
by following steps:
1. Take BW and ETS(Enhanced Transmission Selection)
configuration on VEB(Virtual Ethernet Bridge).
2. Take BW and ETS configuration on VMDQ VSIs.
3. Update TC(Traffic Class) and queues mapping on VMDQ VSIs.
To enable DCB on VMDQ, the number of TCs should not be larger than
the number of queues in VMDQ pools, and the number of queues per
VMDQ pool is specified by CONFIG_RTE_LIBRTE_I40E_QUEUE_NUM_PER_VM
in config/common_* file.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Several structures and macros are added or updated, such
as 'struct i40e_aqc_get_link_status',
'struct i40e_aqc_run_phy_activity' and
'struct i40e_aqc_lldp_set_local_mib_resp'.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Generate a MAC address for each VF during PF host
initialization.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Normally the auto-negotiation is supported by FW. SW need not care about
that. But on x550em_x, FW doesn't support auto-neg. As the x550em_x ports
are 10G, if we connect the port will a peer which is 1G, the link will
always be down.
We need support auto-neg by SW to avoid this link down issue. As we already
have the code to handle the link speed setting, what we need is a trigger.
When the advertised link speed changes, a PHY interruption will be
triggered. So, we should handle this interrupt and call ixgbe_handle_lasi
to set the link speed correctly.
Please be aware it's working when auto-neg is on. If the auto-neg of the
peer port is turned off and its speed is indicated manually, we should also
set the speed of our own port manually.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Add multicast promiscuous mode support on ixgbe VF driver.
Please note if we want to use this promiscuous mode, we need both PF
and VF driver to support it. The reason is this VF feature is
configged on PF.
If use kernel PF driver + dpdk VF driver, make sure kernel PF driver
support VF multicast promiscuous mode. If use dpdk PF + dpdk VF,
better make sure PF driver is the same version as VF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
The MDIO clock speed must be reconfigured after the MAC reset.
The MDIO clock speed becomes invalid, therefore the driver reads
invalid PHY register values. The driver now set the MDIO clock
speed prior to initializing PHY ops and again after the MAC reset.
As now the MDIO speed gets set in more than one place, make a
function for it so it will always be done correctly.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Do not set FDIRCTRL.DROP_NO_MATCH in ixgbe_init_fdir_perfect_82599(),
this bit is already set in ixgbe_set_fdir_drop_queue_82599() which
makes more sense for drivers that call that function.
This resolves an issue where packets were being dropped when switching
to perfect filters mode.
Setting this bit makes no sense in perfect filters mode for the
driver as we do not want to route all packets that don't match an FDIR
rule to a single queue and instead fall back to RSS.
Drivers that need this bit set can call ixgbe_set_fdir_drop_queue_82599()
and the ones that don't, can preserve the old behavior.
Fixes: 2241ce2816 ("ixgbe/base: add flow director drop queue")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch resolves an issue where VF mac address is zeroed out
in cases where the VF driver is loaded while the PF interface
is down.
The solution is to only set it when we get an ACK from the PF.
Fixes: 6202266e56 ("ixgbe/base: vf changes")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Only x550em_x V1 was supported before. Now V2 is supported.
A mask for V1 and V2 is defined and used to support both.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add new X550EM_a devices and their mac types, X550EM_a
and X550EM_a_vf.
Update the code to use the new devices and mac types.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
max_rx_pkt_len already includes ETHER_HDR_LEN and ETHER_CRC_LEN for the
mtu. But, the firmware also adds ETHER_HDR_LEN and ETHER_CRC_LEN to the
mtu specified. Fix by subtracting these values from the mtu before
passing it to firmware.
Fixes: 4b2eff452d ("cxgbe: enable jumbo frames")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
The size of each entry in the port's rss table is actually 2 bytes
and not 1 byte. A segfault occurs when accessing part of port 0's rss
table because it gets overwritten by subsequent port 1's part of the
rss table. Fix by setting the size of each entry appropriately.
Fixes: 92c8a63223 ("cxgbe: add device configuration and Rx support")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The patch add VxLAN & NVGRE TX checksum off-load. When the flag of
outer IP header checksum offload is set, we'll set the context
descriptor to enable this checksum off-load.
Also update release notes for VxLAN & NVGRE checksum off-load support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The names of function for tunnel port configuration are not
accurate. They're tunnel_add/del, better change them to
tunnel_port_add/del.
The old functions are directly replaced because the API and ABI
compatibility of ethdev are already broken in 16.04.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add the CLIs to support the E-tag operation.
1, Offloading of E-tag insertion and stripping.
2, Forwarding the E-tag packets to pools based on the GRP and E-CID_base.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
Add CLIs to config ether type of l2 tunnel, and to enable/disable
a type of l2 tunnel.
Now only e-tag tunnel is supported.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
Add support of l2 tunnel configuration and operations.
1, Support modifying ether type of a type of l2 tunnel.
2, Support enabling and disabling the support of a type of l2 tunnel.
3, Support enabling/disabling l2 tunnel tag insertion/stripping.
4, Support enabling/disabling l2 tunnel packets forwarding.
5, Support adding/deleting forwarding rules for l2 tunnel packets.
Only support E-tag now.
Also update the release note.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Sample app implementing an IPsec Security Geteway.
The main goal of this app is to show the use of cryptodev framework
in a "real world" application.
Currently only supported static IPv4 ESP IPsec tunnels for the following
algorithms:
- Cipher: AES-CBC, NULL
- Authentication: HMAC-SHA1, NULL
Not supported:
- SA auto negotiation (No IKE implementation)
- chained mbufs
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch provides the implementation of a NULL crypto PMD, which supports
NULL cipher and NULL authentication operations, which can be chained together
as follows:
- Authentication Only
- Cipher Only
- Authentication then Cipher
- Cipher then Authentication
As this is a NULL operation device the crypto operations which are submitted for
processing are not actually modified and are stored in a queue pairs processed
packets ring ready for collection when rte_cryptodev_burst_dequeue() is called.
The patch also contains the related unit tests function to test the PMDs
supported operations.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
AES GCM on the cryptodev API was giving invalid results
in some cases, due to an incorrect IV setting.
Added AES GCM in the QAT supported algorithms,
as encryption/decryption is fully functional.
Fixes: 1703e94ac5 ("qat: add driver for QuickAssist devices")
Signed-off-by: John Griffin <john.griffin@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch provides the implementation of an AES-NI accelerated crypto PMD
which is dependent on Intel's multi-buffer library, see the white paper
"Fast Multi-buffer IPsec Implementations on Intel® Architecture Processors"
This PMD supports AES_GCM authenticated encryption and authenticated
decryption using 128-bit AES keys
The patch also contains the related unit tests functions
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John Griffin <john.griffin@intel.com>
Wireless algorithms like Snow3G needs input in bits.
In this patch, changes have been made to incorporate this requirement
in both QAT and SW PMD.
Signed-off-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Added new SW PMD which makes use of the libsso SW library,
which provides wireless algorithms SNOW 3G UEA2 and UIA2
in software.
This PMD supports cipher-only, hash-only and chained operations
("cipher then hash" and "hash then cipher") of the following
algorithms:
- RTE_CRYPTO_SYM_CIPHER_SNOW3G_UEA2
- RTE_CRYPTO_SYM_AUTH_SNOW3G_UIA2
The SNOW 3G hash and cipher algorithms, which are enabled
by this crypto PMD are implemented by Intel's libsso software
library. For library download and build instructions,
see the documentation included (doc/guides/cryptodevs/snow3g.rst)
The patch also contains the related unit tests function to test the PMD
supported operations.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
As cryptodev library does not depend on mbuf_offload library
any longer, this patch removes it.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Fill in the supported features matrix for CXGBE PMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Currently, there is no mechanism that allows the pipeline ports (in/out)
and table action handlers to override the default forwarding decision
(as previously configured per input port or in the table entry). The port
(in/out) and table action handler prototypes have been changed to allow
pipeline action handlers (port in/out, table) to remove the selected
packets from the further pipeline processing and to take full ownership
for these packets. This feature will be helpful to implement functions
such as exception handling (e.g. TTL =0), load balancing etc.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
A new rte_lpm_config structure is used so LPM library will allocate
exactly the amount of memory which is necessary to hold application’s
rules.
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
This patch extend next_hop field from 8-bits to 24-bits in LPM library
for IPv4.
Added versioning symbols to functions and updated
library and applications that have a dependency on LPM library.
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Acked-by: David Hunt <david.hunt@intel.com>
Add introductions on how to enable Vector FM10K Rx/Tx functions,
the preconditions and assumptions on Rx/Tx configuration parameters.
The new content also lists the limitations of vector, so app/customer
can do better to select best Rx/Tx functions.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch documents that the statistics of fm10k based NICs must be
read regularly in order to avoid an undetected 32 bit integer-overflow.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch adds a note to the ixgbe PMD guide, stating
the minimum time that statistics must be polled from
the hardware in order to avoid register values becoming
saturated and "sticking" to the max value.
Reported-by: Jerry Zhang <jerry.zhang@intel.com>
Tested-by: Marcin Kerlin <marcinx.kerlin@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Marcin Kerlin <marcinx.kerlin@intel.com>
Move the structure ``rte_eth_fdir_masks`` change announcement from ABI
to API in release notes.
Fixes: 1409f127d7 (ethdev: fix byte order consistency of flow director)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
There was an ABI change in the release 16.04.
Fixes: fb76dd26a3 ("cmdline: increase command line buffer")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
There was an ABI change and more are coming in the release 16.04.
Fixes: a9963a86b2 ("ethdev: increase RETA entry size")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This patch adds a new function to the EAL API:
int rte_eal_primary_proc_alive(const char *path);
The function indicates if a primary process is alive right now.
This functionality is implemented by testing for a write-
lock on the config file, and the function tests for a lock.
The use case for this functionality is that a secondary
process can wait until a primary process starts by polling
the function and waiting. When the primary is running, the
secondary continues to poll to detect if the primary process
has quit unexpectedly, the secondary process can detect this.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
It deprecates sys files of 'extended_tag' and
'max_read_request_size' which was not documented.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Remove pci configuration of 'extended tag' and 'max read request
size', as they are not required by all devices and it lets PMD to
configure them if necessary.
In addition, 'pci_config_space_set()' is deprecated.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
PCIe feature of 'Extended Tag' is important for 40G performance.
It adds its enabling during each port initialization, to ensure
the high performance.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch fixes some mismatches between the keepalive code
and the docs. Struct names, and descriptions are not in line
with the codebase.
Fixes: e64833f227 ("examples/l2fwd-keepalive: add sample application")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Add known issue about DPDK not compiling on some CPUs
with clang versions older than 3.7.0.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Announce that Malicious Driver Detection is not supported.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
MANY references in the sample applications user guide are wrong because
they are hard-coded and section numbers have changed over the time.
This patch changes thoses references to dynamic ones, in this way if
section numbers change the reference get updated automatically.
Signed-off-by: Mauricio Vasquez B <mauricio.vasquezbernal@studenti.polito.it>
When compiling for i686 targets compilation could fail
if the 32bit libc6-dev package is not installed. The
gcc-multilib packages is a meta-package that will pull
in the necessary dependencies, making setup easier for
beginners.
Reported-by: Weichun Chen <weichunx.chen@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Fixed issue of byte order in ethdev library that the structure
for setting fdir's mask and flow entry is inconsist and made
inputs of mask be in big endian.
Fixes: 2d4c1a9ea2 ("ethdev: add new flow director masks")
Fixes: 76c6f89e80 ("ixgbe: support new flow director masks")
Reported-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Several NICs can handle 512 entries/queues in their RETA table,
an 8 bit field is not large enough for them.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Allow long command lines in testpmd (like flow director with IPv6, ...).
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
removed _VIRTIO_PMD=n from arch config and let arch to use _VIRTIO_PMD
from config/common_linuxapp.
Signed-off-by: Santosh Shukla <sshukla@mvista.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add RTE_DEVEL_BUILD make-variable which can be used to do things
differently when doing development vs building a release,
autodetected from source root .git presence and overridable via
commandline. It is used it to enable -Werror compiler flag and may
be extended to other checks.
Failing build on warnings is a useful developer tool but its bad
for release tarballs which can and do get built with newer
compilers than what was used/available during development. Compilers
routinely add new warnings so code which built silently with cc X
might no longer do so with X+1. This doesn't make the existing code
any more buggier and failing the build in this case does not help
to improve the quality of an already released version either.
This change the default flags which can be tuned with EXTRA_CFLAGS.
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The physically linked-together combined library has been an increasing
source of problems, as was predicted when library and symbol versioning
was introduced. Replace the complex and fragile construction with a
simple linker script which achieves the same without all the problems,
remove the related kludges from eg mlx drivers.
Since creating the linker script is practically zero cost, remove the
config option and just create it always.
Based on a patch by Sergio Gonzales Monroy, linker script approach
initially suggested by Neil Horman.
Suggested-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Fix crc32c hash functions to return a valid crc32c value for
data lengths not multiple of 4 bytes.
ARM code is not tested.
Fixes: af75078fec ("first public release")
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
rte_pktmbuf_alloc_bulk allocates a bulk of packet mbufs.
There is related thread about this bulk API.
http://dpdk.org/dev/patchwork/patch/4718/
Thanks to Konstantin's loop unrolling.
Attached the wiki page about duff's device. It explains the performance
optimization through loop unwinding, and also the most dramatic use of
case label fall-through.
https://en.wikipedia.org/wiki/Duff%27s_device
In this implementation, while() loop is used because we could not assume
count is strictly positive. Using while() loop saves one line of check.
Signed-off-by: Gerald Rogers <gerald.rogers@intel.com>
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
How to reproduce:
1. Start vhost-switch
./examples/vhost/build/vhost-switch -c 0x3 -n 4 -- -p 1 --stat 0
2. Start VM with a virtio port
$ $QEMU -smp cores=2,sockets=1 -m 4G -cpu host -enable-kvm \
-chardev socket,id=char1,path=<path to vhost-user socket> \
-device virtio-net-pci,netdev=vhostuser1 \
-netdev vhost-user,id=vhostuser1,chardev=char1
-object memory-backend-file,id=mem,size=4G,mem-path=<hugetlbfs path>,share=on \
-numa node,memdev=mem -mem-prealloc \
-hda <path to VM img>
3. Start l2fwd in VM
$ ./examples/l2fwd/build/l2fwd -c 0x1 -n 4 -m 1024 -- -p 0x1
4. Use ixia to inject packets in a small data bit rate.
Error:
vhost-switch keeps printing error message:
failed to allocate memory for mbuf.
Root cause:
How many mbufs allocated for a port is calculated by below formula.
NUM_MBUFS_PER_PORT = ((MAX_QUEUES*RTE_TEST_RX_DESC_DEFAULT) + \
(num_switching_cores*MAX_PKT_BURST) + \
(num_switching_cores*RTE_TEST_TX_DESC_DEFAULT) +\
(num_switching_cores*MBUF_CACHE_SIZE))
We suppose num_switching_cores is 1 and MBUF_CACHE_SIZE is 128.
And when initializing port, master core fills mbuf mempool cache,
so there would be some left in that cache, for example 121.
So total mbufs which can be used is:
(MAX_PKT_BURST + MBUF_CACHE_SIZE - 121) = (32 + 128 - 121) = 39.
What makes it worse is that there is a buffer to store mbufs
(which will be tx_burst to physical port), if it occupies some mbufs,
there will be possible < 32 mbufs left, so vhost dequeue prints out
this msg.
In all, it fails to include master core's mbuf mempool cache.
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Fixing the version of the kernel required in the QAT documentation.
Signed-off-by: John Griffin <john.griffin@intel.com>
Acked by: Declan Doherty <declan.doherty@intel.com>
cryptodev_aesni_mb_init was returning the device id of
the device just created, but rte_eal_vdev_init
(the function that calls the first one), was expecting 0 or
negative value.
This made impossible to create more than one aesni_mb device
from command line.
Fixes: 924e84f873 ("aesni_mb: add driver for multi buffer based crypto")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
To claim that we support vhost-user live migration support:
SET_LOG_BASE request will be send only when this feature flag
is set.
Besides this flag, we actually need another feature flag set
to make vhost-user live migration work: VHOST_F_LOG_ALL.
Which, however, has been enabled long time ago.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Add guest offload setting in vhost lib.
Virtio 1.0 spec (5.1.6.4 Processing of Incoming Packets) says:
1. If the VIRTIO_NET_F_GUEST_CSUM feature was negotiated, the
VIRTIO_NET_HDR_F_NEEDS_CSUM bit in flags can be set: if so,
the packet checksum at offset csum_offset from csum_start
and any preceding checksums have been validated. The checksum
on the packet is incomplete and csum_start and csum_offset
indicate how to calculate it (see Packet Transmission point 1).
2. If the VIRTIO_NET_F_GUEST_TSO4, TSO6 or UFO options were
negotiated, then gso_type MAY be something other than
VIRTIO_NET_HDR_GSO_NONE, and gso_size field indicates the
desired MSS (see Packet Transmission point 2).
In order to support these features, the following changes are added,
1. Extend 'VHOST_SUPPORTED_FEATURES' macro to add the offload features negotiation.
2. Enqueue these offloads: convert some fields in mbuf to the fields in virtio_net_hdr.
There are more explanations for the implementation.
For VM2VM case, there is no need to do checksum, for we think the
data should be reliable enough, and setting VIRTIO_NET_HDR_F_NEEDS_CSUM
at RX side will let the TCP layer to bypass the checksum validation,
so that the RX side could receive the packet in the end.
In terms of us-vhost, at vhost RX side, the offload information is
inherited from mbuf, which is in turn inherited from TX side. If we
can still get those info at RX side, it means the packet is from
another VM at same host. So, it's safe to set the
VIRTIO_NET_HDR_F_NEEDS_CSUM, to skip checksum validation.
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add vhost TX offload (CSUM and TSO) support capabilities in vhost lib.
In order to support these features, and the following changes are added,
1. Extend 'VHOST_SUPPORTED_FEATURES' macro to add the offload features
negotiation.
2. Dequeue TX offload: convert the fileds in virtio_net_hdr to the
related fileds in mbuf.
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Updated release documentation to reflect new numbering scheme.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
It was requested by Intel, more than one year ago, to replace the name
"Intel DPDK" by "DPDK".
Some references to the old name were still in some docs and code comments,
leading to confusion.
Fixes: ac8ada004c ("doc: remove Intel references from release notes")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
fix the error reported by checkpatch:
"ERROR: return is not a function, parentheses are not required"
remove parentheses in return like:
"return (logical expressions)"
remove parentheses in return a function like:
"return (rte_mempool_lookup(...))"
Fixes: 6307b909b8 ("lib: remove extra parenthesis after return")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
In order to better compare the drivers and check what is missing
for a common baseline, we need to fill a matrix.
A CSS trick is used to fit the HTML page.
The PDF output needs some LaTeX wizardry.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Add a further ACL example where the elements of the search key
are not entirely fitting into the 4 consecutive bytes of all
input fields.
Signed-off-by: Antonio Fischetti <antonio.fischetti@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
* remove outdated chapter reference to Multi-process support.
* html output converts "--" to "-", this is wrong when explaining the
command arguments, used fixed width quotes for them.
Fixes: fc1f2750a3 ("doc: programmers guide")
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Modern (v1.0) virtio pci device defines several pci capabilities.
Each cap has a configure structure corresponding to it, and the
cap.bar and cap.offset fields tell us where to find it.
Firstly, we map the pci resources by rte_eal_pci_map_device().
We then could easily locate a cfg structure by:
cfg_addr = dev->mem_resources[cap.bar].addr + cap.offset;
Therefore, the entrance of enabling modern (v1.0) pci device support
is to iterate the pci capability lists, and to locate some configs
we care; and they are:
- common cfg
For generic virtio and virtqueue configuration, such as setting/getting
features, enabling a specific queue, and so on.
- nofity cfg
Combining with `queue_notify_off' from common cfg, we could use it to
notify a specific virt queue.
- device cfg
Where virtio_net_config structure is located.
- isr cfg
Where to read isr (interrupt status).
If any of above cap is not found, we fallback to the legacy virtio
handling.
If succeed, hw->vtpci_ops is assigned to modern_ops, where all
operations are implemented by reading/writing a (or few) specific
configuration space from above 4 cfg structures. And that's basically
how this patch works.
Besides those changes, virtio 1.0 introduces a new status field:
FEATURES_OK, which is set after features negotiation is done.
Last, set the VIRTIO_F_VERSION_1 feature flag.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
Fix issue where the navigation levels weren't displayed in the
html sidebar with the new read_the_docs theme.
This was due to the :titlesonly: directive in the high level
index.rst and also due to a stray newline in the parsed version
number.
Reported-by: Matthew Hall <mhall@mhcomputing.net>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Fix missing link in the Linux GSG, accidentally removed
in previous merge:
WARNING: undefined label: linux_gsg_compiling_dpdk
Fixes: 29c673401c ("doc: improve Linux guide layout")
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
In HTML and PDF guides, it is clear in the header that the doc
is related to the DPDK.
So "DPDK" is redundant and can be removed from FAQ and release notes
titles to improve consistency.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Replace "entries" by "queues", it clarifies the case.
Fixes: bd3cea78ab ("doc: announce ABI change for RETA configuration")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Current filtering support will be enhanced to accommodate support
for Chelsio T5 hardware filtering support.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The faq refers to Linux*, with an asterisk, without any equivalent
note or footnote. This is a legacy from older versions of the docs.
This update removes it.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Remove **Contents** and |Today| from the rst doc index files since
these are already added automatically to PDF files and are of
little value to the Html files where the Contents is shown in a
sidebar.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Fix minor rst doc issues in the contributing/design.rst doc to correct
rendering of notes and code blocks.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
This patch updates the release notes to include the changes
made (by me), which were not appropriately documented at the time.
Hence, this patch fixes a number of missing docs,
Fixes: e81a315e5d ("ixgbe: add MAC short packet discard count to Rx errors")
Fixes: 48dd1a82a6 ("ixgbe: remove mac fault counts from Rx errors")
Fixes: 256ff05a9c ("ixgbe: fix Rx errors statistics for UDP checksum")
Also, the CRC byte removal was not added to release notes, so
Fixes: 156c5a8cf9 ("e1000: remove CRC size from byte counters")
Fixes: c03fcee9ab ("ixgbe: remove CRC size from byte counters")
Fixes: 0834d1524d ("i40e: remove CRC size from byte counters")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
test_mp_secondary was initially added by mistake.
rte_snprintf has been removed.
Fixes: 9d41beed24 ("lib: provide initial versioning")
Fixes: 3185322809 ("eal: remove rte_snprintf")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
A rework was prepared by Marc Sune:
http://dpdk.org/ml/archives/dev/2015-October/026037.html
The goal is to retrieve the supported link speed of a device
and to allow 100G devices while having a consistent API.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Jan Viktorin <viktorin@rehivetech.com>
Acked-by: Matej Vido <matejvido@gmail.com>
Current buffer size are not enough for a few testpmd commands.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Olga Shern <olgas@mellanox.com>
This patch adds the patch submission cheatsheet to
the contributers guide. Both HTML and PDF docs show
the cheatsheet on its own page.
Right clicking the SVG image in the HTML doc allows
for viewing the image on its own, useful for printing
in high quality.
The exact appearance of of the cheatsheet will depend
on the default monospace font installed.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Add a document to explain the DPDK patch submission and review process.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Add a known issue to warn that PF reset event/request is not
handled by any VF drivers till 2.2, and which should be fixed
in the future.
Reported-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
This patch updates the release notes with the features
added to ip_pipeline application.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Fan Zhang <roy.fan.zhang@intel.com>
Fix typos in sample console commands.
Remove "user@target:~$" prefixes in command lines.
Add --socket-mem 1024 to vhost-switch command lines.
Without the --socket-mem parameter all hugepages will be allocated
to vhost-switch, leaving no memory for the VM.
Add --disable-hw-vlan-filter parameter to testpmd command lines.
Without this parameter testpmd fails on startup in the VM.
Increase value of --sock-mem parameter to testpmd as original
value was too small.
Fixes: d0dff9ba44 ("doc: sample application user guide"
Fixes: 9bc23cb820 ("doc: add vhost-user to sample guide")
Fixes: 43866bf71d ("doc: fix vhost sample parameter")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Add note to the documentation that only x86_64 versions of the external
libraries are currently provided.
Signed-off-by: Matej Vido <matejvido@gmail.com>
- Update features, limitations, configuration and prerequisites sections.
- Add a note to describe RSS behavior differences with librte_pmd_mlx4 in
testpmd.
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
-Split "Features" and "Limitations" sections.
-Update limitations with missing information.
-Update prerequisites with supported MLNX_OFED release, firmware and
CPU architectures.
-Enhance usage example with openibd script.
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This documentation covers introductions and limitations on Intel
FM10000 series products.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Update interrupt related limitations for e1000em nic.
It only support one interrupt source and not support auto-clear.
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Add a new guide doc as part of the Linux Getting Started Guide.
The document is a step-by-step guide on how to get high performance
with DPDK on an Intel platform.
It is designed for users who are not familiar with DPDK but would like
to get the best performance with NICs.
Signed-off-by: Qian Xu <qian.q.xu@intel.com>
Update the documentation to reflect that the minimum Linux kernel
requirement for DPDK 2.2 has increased from 2.6.33 to 2.6.34.
Compatibility with kernel 2.6.33 was dropped, after discussion on
the mailing list, in the following commit:
2e6e9e2157 ("igb_uio: use existing PCI macros")
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Enable Doxygen parsing of DPDK example files so that the example
code is linked to and from the API docs. This allows the reader
to see examples of API usage in context by following a link.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Change the Sphinx default theme from "alabaster" to the ReadTheDocs
theme. See for example:
http://dpdk.readthedocs.org/en/latest/
This looks better for technical documentation and in particular
it has a 80 char wide verbatim block rendering.
Also add logos for the html and latex docs.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Remove requirement for occasionally hard to find/install
DejaVuSansMono font. It isn't gnerally required anyway.
The default mono font is sufficient.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Turn off the permalink symbol in the Sphinx generated html docs.
This is a distracting mouseover when reading the docs and links
to sections can still be obtained from the doc index.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
This commit removes the performance thread example from
examples/Makefile, and marks the example as "experimental"
in the release note, and it its API headers files.
Signed-off-by: Ian Betts <ian.betts@intel.com>
This commit adds the sample application user guide for the
performance thread sample application.
Signed-off-by: Ian Betts <ian.betts@intel.com>
Acked-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Further enhancements to the userspace ethtool implementation that was
submitted in 2.1 and packaged as a self-contained sample application.
Implements an rte_ethtool shim layer based on rte_ethdev API, along
with a command prompt driven demonstration application.
Signed-off-by: Remy Horton <remy.horton@intel.com>
In addition to git tags, support validating abi between any legal
gitrevisions(7) syntaxes, such as "validate-abi.sh -1 . <target>"
"validate-abi.sh master mybranch <target>" etc in addition to
validating between tags. Makes it easier to run the validator
for in-development work.
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Fix the examples in the netmap compatibility sample application
docs which referred to the packet_reordering application.
Also fix some minor rst formatting issues.
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Fix repeated typo in the "Compiling the Application" section of
almost all of the sample app docs.
This generally gets copied into new sample app guides.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The patch adds missing new line to "Managing ABI updates" section.
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: John McNamara <john.mcnamara@intel.com>
Fixes: ab3257e13d ("app/testpmd: add command to display queue info")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Correct the sample code in the pcap_ring.rst file to match the latest
rte_eth_ring.c code.
The parameters to the rte_eth_from_rings() function have changed since
the documentation was written.
The API change occurred before DPDK 1.8 when the rst files were added.
The original documentation on which the pcap_ring.rst file was based was
not correct.
Fixes: fc1f2750a3 ("doc: programmers guide")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Lookup burst size was changed for exact match
from 4 to 8, for both ipv4 and ipv6, but actually only
4 keys were being looked up for ipv6, instead of 8,
causing random segmentation faults.
Fixes: 80fcb4d4 ("examples/l3fwd: increase lookup burst size to 8")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Reshma Pattan <reshma.pattan@intel.com>
examples/vhost_xen/main.c:659:61: error: has no member named data
rte_memcpy((void *)(uintptr_t)buff_addr, (const void*)buff->data, rte_pktmbuf_data_len(buff));
^
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
In order to be installed system-wise, this application needs
a prefix. So it makes clear that it is DPDK related.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
The old install command was:
make install T=x86_64-native-linuxapp-gcc DESTDIR=install
It still works and can be replaced by these more standard commands:
make config T=x86_64-native-linuxapp-gcc 0=x86_64-native-linuxapp-gcc
make O=x86_64-native-linuxapp-gcc
make install O=x86_64-native-linuxapp-gcc prefix= DESTDIR=install
It means the "make install" do not perform any compilation anymore when T
is not used. It is done only in pre_install to keep compatibility with the
old syntax based on T= option.
The default prefix /usr/local is empty in the T= case which is
used only for a local install.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
The rule "install" follows these conventions:
http://gnu.org/prep/standards/html_node/Directory-Variables.htmlhttp://gnu.org/prep/standards/html_node/DESTDIR.html
The variable sdkdir has been added to the more standards ones,
to configure the directory used with RTE_SDK when using the DPDK makefiles
to build an application.
It is still possible to build DPDK with the "install T=" rule without
specifying any DESTDIR. In such case there is no install, as before.
The old usage of an installed SDK is:
make -C examples/helloworld RTE_SDK=$(readlink -m $DESTDIR) \
RTE_TARGET=x86_64-native-linuxapp-gcc
RTE_TARGET can be specified but is useless now with an installed SDK.
The RTE_SDK directory must now point to a different path depending of
the installation.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
The multi-target install create some subdirectories with the target name
which is not standard for a "make install" procedure.
The uninstall procedure cannot be applied properly (without removing
all files in a directory). It would need to pre-compute paths.
As it is a packaging issue, it is removed from the build system capabilities.
The variable BUILD_DIR is also renamed to RTE_OUTPUT used in other files.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
It is not possible to test every configs on an unique machine.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
The function rte_mempool_obj_iter used in mlx drivers
was not exported. So the driver loading was failing:
EAL: open shared lib librte_pmd_mlx4.so
EAL: x86_64-native-linuxapp-gcc/lib/librte_pmd_mlx4.so:
undefined symbol: rte_mempool_obj_iter
Fixes: 9d41beed24 ("lib: provide initial versioning")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
If use DPDK PF + DPDK VF on igb NICs, we find the MAC address of VF
port is always 0. Because we forget to give it a value if this MAC
address is not assigned by PF. This patch'll assign a random MAC
address to igb VF port as ixgbe does.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch relates to ABI change proposed for librte_table.
The key_mask parameter is added for 8-byte and 16-byte
key extendible bucket and LRU tables.The release notes
is updated and the deprecation notice is removed.
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Added functions for adding/deleting multiple records to table owned by
pipeline. The LIBABIVER number is incremented.
Signed-off-by: Maciej Gajdzica <maciejx.t.gajdzica@intel.com>
Signed-off-by: Marcin Kerlin <marcinx.kerlin@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
New functions prototypes for bulk add/delete added to table API. New
functions allows adding/deleting multiple records with single function
call. For now those functions are implemented only for ACL table. For
other tables these function pointers are set to NULL.
Signed-off-by: Maciej Gajdzica <maciejx.t.gajdzica@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
The crypto API is in an early state.
It requires more discussions and experiments to declare it stable,
as discussed in http://dpdk.org/ml/archives/dev/2015-November/028634.html
A documentation section will be required in the guides.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch provides the initial implementation of the AES-NI multi-buffer
based crypto poll mode driver using DPDK's new cryptodev framework.
This PMD is dependent on Intel's multibuffer library, see the whitepaper
"Fast Multi-buffer IPsec Implementations on Intel® Architecture
Processors", see ref 1 for details on the library's design and ref 2 to
download the library itself. This initial implementation is limited to
supporting the chained operations of "hash then cipher" or "cipher then
hash" for the following cipher and hash algorithms:
Cipher algorithms:
- RTE_CRYPTO_CIPHER_AES_CBC (with 128-bit, 192-bit and 256-bit keys supported)
Authentication algorithms:
- RTE_CRYPTO_AUTH_SHA1_HMAC
- RTE_CRYPTO_AUTH_SHA256_HMAC
- RTE_CRYPTO_AUTH_SHA512_HMAC
- RTE_CRYPTO_AUTH_AES_XCBC_MAC
Important Note:
Due to the fact that the multi-buffer library is designed for
accelerating IPsec crypto operation, the digest's generated for the HMAC
functions are truncated to lengths specified by IPsec RFC's, ie RFC2404
for using HMAC-SHA-1 with IPsec specifies that the digest is truncate
from 20 to 12 bytes.
Build instructions:
To build DPDK with the AESNI_MB_PMD the user is required to download
(ref 2) and compile the multi-buffer library on there system before
building DPDK. The environmental variable AESNI_MULTI_BUFFER_LIB_PATH
must be exported with the path where you extracted and built the multi
buffer library and finally set CONFIG_RTE_LIBRTE_PMD_AESNI_MB=y in
config/common_linuxapp.
Current status: It's doesn't support crypto operation
across chained mbufs, or cipher only or hash only operations.
ref 1:
https://www-ssl.intel.com/content/www/us/en/intelligent-systems/intel-technology/fast-multi-buffer-ipsec-implementations-ia-processors-p
ref 2: https://downloadcenter.intel.com/download/22972
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
This patch adds a PMD for the Intel Quick Assist Technology DH895xxC
hardware accelerator.
This patch depends on a QAT PF driver for device initialization. See
the file docs/guides/cryptodevs/qat.rst for configuration details
This patch supports a limited subset of QAT device functionality,
currently supporting chaining of cipher and hash operations for the
following algorithmsd:
Cipher algorithms:
- RTE_CRYPTO_CIPHER_AES_CBC (with 128-bit, 192-bit and 256-bit keys supported)
Hash algorithms:
- RTE_CRYPTO_AUTH_SHA1_HMAC
- RTE_CRYPTO_AUTH_SHA256_HMAC
- RTE_CRYPTO_AUTH_SHA512_HMAC
- RTE_CRYPTO_AUTH_AES_XCBC_MAC
Some limitation on this patchset which shall be contributed in a
subsequent release:
- Chained mbufs are not supported.
- Hash only is not supported.
- Cipher only is not supported.
- Only in-place is currently supported (destination address is
the same as source address).
- Only supports session-oriented API implementation (session-less
APIs are not supported).
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: John Griffin <john.griffin@intel.com>
Signed-off-by: Des O Dea <des.j.o.dea@intel.com>
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
This library add support for adding a chain of offload operations to a
mbuf. It contains the definition of the rte_mbuf_offload structure as
well as helper functions for attaching offloads to mbufs and a mempool
management functions.
This initial implementation supports attaching multiple offload
operations to a single mbuf, but only a single offload operation of a
specific type can be attach to that mbuf.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch contains the initial proposed APIs and device framework for
integrating crypto packet processing into DPDK.
features include:
- Crypto device configuration / management APIs
- Definitions of supported cipher algorithms and operations.
- Definitions of supported hash/authentication algorithms and
operations.
- Crypto session management APIs
- Crypto operation data structures and APIs allocation of crypto
operation structure used to specify the crypto operations to
be performed on a particular mbuf.
- Extension of mbuf to contain crypto operation data pointer and
extra flags.
- Burst enqueue / dequeue APIs for processing of crypto operations.
Signed-off-by: Des O Dea <des.j.o.dea@intel.com>
Signed-off-by: John Griffin <john.griffin@intel.com>
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
The functions rte_eth_rx_queue_count and rte_eth_descriptor_done are
supported by very few PMDs. Therefore, it is best to check for support
for the functions in the ethdev library, so as to avoid run-time crashes
at run-time if the application goes to use those APIs. Similarly, the
port parameter should also be checked for validity.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The functions for rx/tx burst, for rx_queue_count and descriptor_done in
the ethdev library all had two copies of the code. One copy in
rte_ethdev.h was inlined for performance, while a second was in
rte_ethdev.c for debugging purposes only. We can eliminate the second
copy of the functions by moving the additional debug checks into the
copies of the functions in the header file. [Any compilation for
debugging at optimization level 0 will not inline the function so the
result should be same as when the function was in the .c file.]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
