algorithm based on the Internet-Draft "draft-leith-tcp-htcp-06.txt". It is
implemented as a kernel module compatible with the recently committed modular
congestion control framework.
H-TCP was designed to provide increased throughput in fast and long-distance
networks. It attempts to maintain fairness when competing with legacy NewReno
TCP in lower speed scenarios where NewReno is able to operate adequately. The
paper "H-TCP: A framework for congestion control in high-speed and long-distance
networks" provides additional detail.
In collaboration with: David Hayes <dahayes at swin edu au> and
Grenville Armitage <garmitage at swin edu au>
Sponsored by: FreeBSD Foundation
Reviewed by: rpaulo (older patch from a few weeks ago)
MFC after: 3 months
algorithm based on the Internet-Draft "draft-rhee-tcpm-cubic-02.txt". It is
implemented as a kernel module compatible with the recently committed modular
congestion control framework.
CUBIC was designed for provide increased throughput in fast and long-distance
networks. It attempts to maintain fairness when competing with legacy NewReno
TCP in lower speed scenarios where NewReno is able to operate adequately. The
paper "CUBIC: A New TCP-Friendly High-Speed TCP Variant" provides additional
detail.
In collaboration with: David Hayes <dahayes at swin edu au> and
Grenville Armitage <garmitage at swin edu au>
Sponsored by: FreeBSD Foundation
Reviewed by: rpaulo (older patch from a few weeks ago)
MFC after: 3 months
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
packets which go through each USB host controllers. Its implementations
are almost based on BPF code and very similar with it except it's
little bit customized for USB packet only. The userland program
usbdump(8) would be committed soon.
Discussed with: hps, thompsa, yongari
Move logic of building ACPI headers for acpi_wakeup.c into better places,
remove intermediate makefile and shell script, and reduce diff between i386
and amd64.
This can happen if the algos are built as modules but are not loaded. If
the selected ratectl algo is not available, try to load it (The load
module functions does nothing currently). Add a dummy ratectl algo which
always selects the first available rate. Use that one if the desired algo
is not available.
MFC after: 1 week
replace mii_phy_probe() altogether. Compared to the latter the advantages
of mii_attach() are:
- intended to be called multiple times in order to attach PHYs in multiple
passes (f.e. in order to only use sub-ranges of the 0 to MII_NPHY - 1
range)
- being able to pass along the capability mask from the NIC to the PHY
drivers
- being able to specify at which address (phyloc) to probe for a PHY
(instead of always probing at all addresses from 0 to MII_NPHY - 1)
- being able to specify which PHY instance (offloc) to attach
- being able to pass along MIIF_* flags from the NIC to the PHY drivers
(f.e. as required to indicated to the PHY drivers that flow control is
supported by the NIC driver, which actually is the motivation for this
change).
While at it, I used the opportunity to get rid of some hacks in mii(4)
like miibus_probe() generally doing work besides sheer probing and the
"EVIL HACK" (which will vanish entirely along with mii_phy_probe()) by
passing the struct ifnet pointer via an argument of mii_attach() as well
as to fix some resource leaks in mii(4) in case something fails.
Commits which will update the PHY drivers to honor the MII flags passed
down from the NIC drivers and take advantage of mii_attach() to get rid
of certain types of hacks in NIC and PHY drivers as well as a conversion
of the remaining uses of mii_phy_probe() will follow shortly.
Reviewed by: jhb, yongari
Obtained from: NetBSD (partially)
Unlike actual MTRR, this only controls the mapping attributes for
subsequent mmap() of /dev/mem. Nonetheless, the support is sufficiently
MTRR-like that Xorg can use it, which translates into an enormous increase
in graphics performance on PowerPC.
MFC after: 2 weeks
in the kernel (just as inet_ntoa() and inet_aton()) are and sync their
prototype accordingly with already mentioned functions.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, rstone
Approved by: dfr
MFC after: 2 weeks
- Don't probe for PHYs if we already know to use a SERDES. Unlike as with
cas(4) this only serves to speed up the the device attach though and can
only be determined via the OFW device tree but not from the VPD.
- Don't touch the MIF when using a SERDES.
- Add some missing bus space barriers, mainly in the PCS code path.
Bring in a driver for the LSI Logic MPT2 6Gb SAS controllers.
This driver supports basic I/O, and works with SAS and SATA drives and
expanders.
Basic error recovery works (i.e. timeouts and aborts) as well.
Integrated RAID isn't supported yet, and there are some known bugs.
So this isn't ready for production use, but is certainly ready for
testing and additional development. For the moment, new commits to this
driver should go into the FreeBSD Perforce repository first
(//depot/projects/mps/...) and then get merged into -current once
they've been vetted.
This has only been added to the amd64 GENERIC, since that is the only
architecture I have tested this driver with.
Submitted by: scottl
Discussed with: imp, gibbs, will
Sponsored by: Yahoo, Spectra Logic Corporation
Use MACHINE_CPUARCH in preference to MACHINE_ARCH. The former is the
source code location of the machine, the latter the binary output. In
general, we want to use MACHINE_CPUARCH instead of MACHINE_ARCH unless
we're tesitng for a specific target. The isn't even moot for
i386/amd64 where there's momemntum towards a MACHINE_CPUARCH == x86,
although a specific cleanup for that likely would be needed...
Add kernel side support for Secure Neighbor Discovery (SeND), RFC 3971.
The implementation consists of a kernel module that gets packets from
the nd6 code, sends them to user space on a dedicated socket and reinjects
them back for further processing.
Hooks are used from nd6 code paths to divert relevant packets to the
send implementation for processing in user space. The hooks are only
triggered if the send module is loaded. In case no user space
application is connected to the send socket, processing continues
normaly as if the module would not be loaded. Unloading the module
is not possible at this time due to missing nd6 locking.
The native SeND socket is similar to a raw IPv6 socket but with its own,
internal pseudo-protocol.
Approved by: bz (mentor)
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.
Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.
This commit requires IP6PROTOSPACER, introduced in r211115.
Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks
module that can be used by both the regular and experimental nfs
clients. This fixes the problem reported by jh@ where /dev/nfslock
would be registered twice when both nfs clients were used.
I also defined the size of the lm_fh field to be the correct value,
as it should be the maximum size of an NFSv3 file handle.
Reviewed by: jh
MFC after: 2 weeks
The aeskeys_{amd64,i386}.S content was mostly obtained from OpenBSD,
no objections to the license from core.
Hardware provided by: Sentex Communications
Tested by: fabient, pho (previous versions)
MFC after: 1 month
in Solaris 10 updates 141445-09 and 142901-14.
Detailed information:
(OpenSolaris revisions and Bug IDs, Solaris 10 patch numbers)
7844:effed23820ae
6755435 zfs_open() and zfs_close() needs to use ZFS_ENTER/ZFS_VERIFY_ZP (141445-01)
7897:e520d8258820
6748436 inconsistent zpool.cache in boot_archive could panic a zfs root filesystem upon boot-up (141445-01)
7965:b795da521357
6740164 zpool attach can create an illegal root pool (141909-02)
8084:b811cc60d650
6769612 zpool_import() will continue to write to cachefile even if altroot is set (N/A)
8121:7fd09d4ebd9c
6757430 want an option for zdb to disable space map loading and leak tracking (141445-01)
8129:e4f45a0bfbb0
6542860 ASSERT: reason != VDEV_LABEL_REMOVE||vdev_inuse(vd, crtxg, reason, 0) (141445-01)
8188:fd00c0a81e80
6761100 want zdb option to select older uberblocks (141445-01)
8190:6eeea43ced42
6774886 zfs_setattr() won't allow ndmp to restore SUNWattr_rw (141445-01)
8225:59a9961c2aeb
6737463 panic while trying to write out config file if root pool import fails (141445-01)
8227:f7d7be9b1f56
6765294 Refactor replay (141445-01)
8228:51e9ca9ee3a5
6572357 libzfs should do more to avoid mnttab lookups (141909-01)
6572376 zfs_iter_filesystems and zfs_iter_snapshots get objset stats twice (141909-01)
8241:5a60f16123ba
6328632 zpool offline is a bit too conservative (141445-01)
6739487 ASSERT: txg <= spa_final_txg due to scrub/export race (141445-01)
6767129 ASSERT: cvd->vdev_isspare, in spa_vdev_detach() (141445-01)
6747698 checksum failures after offline -t / export / import / scrub (141445-01)
6745863 ZFS writes to disk after it has been offlined (141445-01)
6722540 50% slowdown on scrub/resilver with certain vdev configurations (141445-01)
6759999 resilver logic rewrites ditto blocks on both source and destination (141445-01)
6758107 I/O should never suspend during spa_load() (141445-01)
6776548 codereview(1) runs off the page when faced with multi-line comments (N/A)
6761406 AMD errata 91 workaround doesn't work on 64-bit systems (141445-01)
8242:e46e4b2f0a03
6770866 GRUB/ZFS should require physical path or devid, but not both (141445-01)
8269:03a7e9050cfd
6674216 "zfs share" doesn't work, but "zfs set sharenfs=on" does (141445-01)
6621164 $SRC/cmd/zfs/zfs_main.c seems to have a syntax error in the translation note (141445-01)
6635482 i18n problems in libzfs_dataset.c and zfs_main.c (141445-01)
6595194 "zfs get" VALUE column is as wide as NAME (141445-01)
6722991 vdev_disk.c: error checking for ddi_pathname_to_dev_t() must test for NODEV (141445-01)
6396518 ASSERT strings shouldn't be pre-processed (141445-01)
8274:846b39508aff
6713916 scrub/resilver needlessly decompress data (141445-01)
8343:655db2375fed
6739553 libzfs_status msgid table is out of sync (141445-01)
6784104 libzfs unfairly rejects numerical values greater than 2^63 (141445-01)
6784108 zfs_realloc() should not free original memory on failure (141445-01)
8525:e0e0e525d0f8
6788830 set large value to reservation cause core dump (141445-01)
6791064 want sysevents for ZFS scrub (141445-01)
6791066 need to be able to set cachefile on faulted pools (141445-01)
6791071 zpool_do_import() should not enable datasets on faulted pools (141445-01)
6792134 getting multiple properties on a faulted pool leads to confusion (141445-01)
8547:bcc7b46e5ff7
6792884 Vista clients cannot access .zfs (141445-01)
8632:36ef517870a3
6798384 It can take a village to raise a zio (141445-01)
8636:7e4ce9158df3
6551866 deadlock between zfs_write(), zfs_freesp(), and zfs_putapage() (141909-01)
6504953 zfs_getpage() misunderstands VOP_GETPAGE() interface (141909-01)
6702206 ZFS read/writer lock contention throttles sendfile() benchmark (141445-01)
6780491 Zone on a ZFS filesystem has poor fork/exec performance (141445-01)
6747596 assertion failed: DVA_EQUAL(BP_IDENTITY(&zio->io_bp_orig), BP_IDENTITY(zio->io_bp))); (141445-01)
8692:692d4668b40d
6801507 ZFS read aggregation should not mind the gap (141445-01)
8697:e62d2612c14d
6633095 creating a filesystem with many properties set is slow (141445-01)
8768:dfecfdbb27ed
6775697 oracle crashes when overwriting after hitting quota on zfs (141909-01)
8811:f8deccf701cf
6790687 libzfs mnttab caching ignores external changes (141445-01)
6791101 memory leak from libzfs_mnttab_init (141445-01)
8845:91af0d9c0790
6800942 smb_session_create() incorrectly stores IP addresses (N/A)
6582163 Access Control List (ACL) for shares (141445-01)
6804954 smb_search - shortname field should be space padded following the NULL terminator (N/A)
6800184 Panic at smb_oplock_conflict+0x35() (N/A)
8876:59d2e67b4b65
6803822 Reboot after replacement of system disk in a ZFS mirror drops to grub> prompt (141445-01)
8924:5af812f84759
6789318 coredump when issue zdb -uuuu poolname/ (141445-01)
6790345 zdb -dddd -e poolname coredump (141445-01)
6797109 zdb: 'zdb -dddddd pool_name/fs_name inode' coredump if the file with inode was deleted (141445-01)
6797118 zdb: 'zdb -dddddd poolname inum' coredump if I miss the fs name (141445-01)
6803343 shareiscsi=on failed, iscsitgtd failed request to share (141445-01)
9030:243fd360d81f
6815893 hang mounting a dataset after booting into a new boot environment (141445-01)
9056:826e1858a846
6809691 'zpool create -f' no longer overwrites ufs infomation (141445-01)
9179:d8fbd96b79b3
6790064 zfs needs to determine uid and gid earlier in create process (141445-01)
9214:8d350e5d04aa
6604992 forced unmount + being in .zfs/snapshot/<snap1> = not happy (141909-01)
6810367 assertion failed: dvp->v_flag & VROOT, file: ../../common/fs/gfs.c, line: 426 (141909-01)
9229:e3f8b41e5db4
6807765 ztest_dsl_dataset_promote_busy needs to clean up after ENOSPC (141445-01)
9230:e4561e3eb1ef
6821169 offlining a device results in checksum errors (141445-01)
6821170 ZFS should not increment error stats for unavailable devices (141445-01)
6824006 need to increase issue and interrupt taskqs threads in zfs (141445-01)
9234:bffdc4fc05c4
6792139 recovering from a suspended pool needs some work (141445-01)
6794830 reboot command hangs on a failed zfs pool (141445-01)
9246:67c03c93c071
6824062 System panicked in zfs_mount due to NULL pointer dereference when running btts and svvs tests (141909-01)
9276:a8a7fc849933
6816124 System crash running zpool destroy on broken zpool (141445-03)
9355:09928982c591
6818183 zfs snapshot -r is slow due to set_snap_props() doing txg_wait_synced() for each new snapshot (141445-03)
9391:413d0661ef33
6710376 log device can show incorrect status when other parts of pool are degraded (141445-03)
9396:f41cf682d0d3 (part already merged)
6501037 want user/group quotas on ZFS (141445-03)
6827260 assertion failed in arc_read(): hdr == pbuf->b_hdr (141445-03)
6815592 panic: No such hold X on refcount Y from zfs_znode_move (141445-03)
6759986 zfs list shows temporary %clone when doing online zfs recv (141445-03)
9404:319573cd93f8
6774713 zfs ignores canmount=noauto when sharenfs property != off (141445-03)
9412:4aefd8704ce0
6717022 ZFS DMU needs zero-copy support (141445-03)
9425:e7ffacaec3a8
6799895 spa_add_spares() needs to be protected by config lock (141445-03)
6826466 want to post sysevents on hot spare activation (141445-03)
6826468 spa 'allowfaulted' needs some work (141445-03)
6826469 kernel support for storing vdev FRU information (141445-03)
6826470 skip posting checksum errors from DTL regions of leaf vdevs (141445-03)
6826471 I/O errors after device remove probe can confuse FMA (141445-03)
6826472 spares should enjoy some of the benefits of cache devices (141445-03)
9443:2a96d8478e95
6833711 gang leaders shouldn't have to be logical (141445-03)
9463:d0bd231c7518
6764124 want zdb to be able to checksum metadata blocks only (141445-03)
9465:8372081b8019
6830237 zfs panic in zfs_groupmember() (141445-03)
9466:1fdfd1fed9c4
6833162 phantom log device in zpool status (141445-03)
9469:4f68f041ddcd
6824968 add ZFS userquota support to rquotad (141445-03)
9470:6d827468d7b5
6834217 godfather I/O should reexecute (141445-03)
9480:fcff33da767f
6596237 Stop looking and start ganging (141909-02)
9493:9933d599bc93
6623978 lwb->lwb_buf != NULL, file ../../../uts/common/fs/zfs/zil.c, line 787, function zil_lwb_commit (141445-06)
9512:64cafcbcc337
6801810 Commit of aligned streaming rewrites to ZIL device causes unwanted disk reads (N/A)
9515:d3b739d9d043
6586537 async zio taskqs can block out userland commands (142901-09)
9554:787363635b6a
6836768 zfs_userspace() callback has no way to indicate failure (N/A)
9574:1eb6a6ab2c57
6838062 zfs panics when an error is encountered in space_map_load() (141909-02)
9583:b0696cd037cc
6794136 Panic BAD TRAP: type=e when importing degraded zraid pool. (141909-03)
9630:e25a03f552e0
6776104 "zfs import" deadlock between spa_unload() and spa_async_thread() (141445-06)
9653:a70048a304d1
6664765 Unable to remove files when using fat-zap and quota exceeded on ZFS filesystem (141445-06)
9688:127be1845343
6841321 zfs userspace / zfs get userused@ doesn't work on mounted snapshot (N/A)
6843069 zfs get userused@S-1-... doesn't work (N/A)
9873:8ddc892eca6e
6847229 assertion failed: refcount_count(&tx->tx_space_written) + delta <= tx->tx_space_towrite in dmu_tx.c (141445-06)
9904:d260bd3fd47c
6838344 kernel heap corruption detected on zil while stress testing (141445-06)
9951:a4895b3dd543
6844900 zfs_ioc_userspace_upgrade leaks (N/A)
10040:38b25aeeaf7a
6857012 zfs panics on zpool import (141445-06)
10000:241a51d8720c
6848242 zdb -e no longer works as expected (N/A)
10100:4a6965f6bef8
6856634 snv_117 not booting: zfs_parse_bootfs: error2 (141445-07)
10160:a45b03783d44
6861983 zfs should use new name <-> SID interfaces (N/A)
6862984 userquota commands can hang (141445-06)
10299:80845694147f
6696858 zfs receive of incremental replication stream can dereference NULL pointer and crash (N/A)
10302:a9e3d1987706
6696858 zfs receive of incremental replication stream can dereference NULL pointer and crash (fix lint) (N/A)
10575:2a8816c5173b (partial merge)
6882227 spa_async_remove() shouldn't do a full clear (142901-14)
10800:469478b180d9
6880764 fsync on zfs is broken if writes are greater than 32kb on a hard crash and no log attached (142901-09)
6793430 zdb -ivvvv assertion failure: bp->blk_cksum.zc_word[2] == dmu_objset_id(zilog->zl_os) (N/A)
10801:e0bf032e8673 (partial merge)
6822816 assertion failed: zap_remove_int(ds_next_clones_obj) returns ENOENT (142901-09)
10810:b6b161a6ae4a
6892298 buf->b_hdr->b_state != arc_anon, file: ../../common/fs/zfs/arc.c, line: 2849 (142901-09)
10890:499786962772
6807339 spurious checksum errors when replacing a vdev (142901-13)
11249:6c30f7dfc97b
6906110 bad trap panic in zil_replay_log_record (142901-13)
6906946 zfs replay isn't handling uid/gid correctly (142901-13)
11454:6e69bacc1a5a
6898245 suspended zpool should not cause rest of the zfs/zpool commands to hang (142901-10)
11546:42ea6be8961b (partial merge)
6833999 3-way deadlock in dsl_dataset_hold_ref() and dsl_sync_task_group_sync() (142901-09)
Discussed with: pjd
Approved by: delphij (mentor)
Obtained from: OpenSolaris (multiple Bug IDs)
MFC after: 2 months
FreeBSD. SIFTR logs a range of statistics on active TCP connections to a log
file, providing the ability to make highly granular measurements of TCP
connection state. The tool is aimed at system administrators, developers and
researchers alike. Please take it for a spin and test it out - the man page
should have all the information required to get you going.
Many thanks go to the Cisco University Research Program Fund at Community
Foundation Silicon Valley and the FreeBSD Foundation. Their support of our work
at the Centre for Advanced Internet Architectures, Swinburne University of
Technology is greatly appreciated.
Sponsored by: Cisco URP, FreeBSD Foundation
Reviewed by: dwmalone, gnn, rpaulo
Tested by: Many on freebsd-current@ and elsewhere over the years
MFC after: 1 month
the core changes but left out the shared code, lol.
Well, and a couple fixes to the core... hopefully
this will all be complete now.
Happy happy joy joy :)
It has more features than acpi_aiboost(4) and it will eventually replace
acpi_aiboost(4).
Submitted by: Constantine A. Murenin <cnst at FreeBSD.org>
Reviewed by: freebsd-acpi, imp
MFC after: 1 month
passing through. Modifications are restricted to a subset of C language
operations on unsigned integers of 8, 16, 32 or 64 bit size.
These are: set to new value (=), addition (+=), subtraction (-=),
multiplication (*=), division (/=), negation (= -), bitwise AND (&=),
bitwise OR (|=), bitwise eXclusive OR (^=), shift left (<<=),
shift right (>>=). Several operations are all applied to a packet
sequentially in order they were specified by user.
Submitted by: Maxim Ignatenko <gelraen.ua at gmail.com>
Vadim Goncharov <vadimnuclight at tpu.ru>
Discussed with: net@
Approved by: mav (mentor)
MFC after: 1 month
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
Intention of this commit is to let us take a full advantage
of libusb(8) ported to Linux. This decreases a possibility of getting
any collisions within ioctl() "command" space, especially with
relation to LINUX_SNDCTL_SEQ... stuff.
Basically, we provide commands, that will be mapped in the kernel
to correct ones and forward those to the USB layer. Port enabling
functionality brought with this patch is here:
http://www.freebsd.org/cgi/query-pr.cgi?pr=146895
Bump __FreeBSD_version to catch, since which version installing a
port makes sense.
This patch should bring no regressions. So far, only i386 is tested.
Tested by: thompsa@
Reviewed by: thompsa@
OKed by: netchild@
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
useful it will be, but we really need to be keying off something other
than MACHINE for this anyway since on arm and mips we have lots of
these running around (one for each SoC family)...
in a device independent manner. Also include an example anticipatory
scheduler, gsched_rr, which gives very nice performance improvements
in presence of competing random access patterns.
This is joint work with Fabio Checconi, developed last year
and presented at BSDCan 2009. You can find details in the
README file or at
http://info.iet.unipi.it/~luigi/geom_sched/
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.
igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.
MFC in a week
Rather than remove it for all architectures (which was a botch in
r205845), remove it only for arm and mips until that can be sorted out.
Pointy Hat: imp
Submitted by: Navdeep Parhar
MFC after: 7 days
into):
o Don't build vpo and syscons on mips or arm either
o Add a section for mips and arm breakages, and document why.
This is easier than opting in on all the other architectures:
# no BUS_SPACE_UNSPECIFIED: bce, bwi, bwn, mfi, mpt, siba_bwn
# No barrier instruction support (specific to this driver): sym
# no uart_cpu_$MACHINE_ARCH: uart
(mips has, by inspection, the same issues as arm, so ditto for it)
MFC after: 7 days
o Switch to ITANIUM2 has the cpu. This has absolutely no effect
on the code, but makes for a better example.
o Drop COMPAT_FREEBSD6. We're tier 2, so you're supposed to run
8-stable or newer.
o Add PREEMPTION. It works now.
o Remove HWPMC_HOOKS. We don't have support for hwpmc yet.
o Add a bunch of new devices: atapist, hptiop, amr, ips, twa, igb,
ixgbe, ae, age, alc, ale, bce, bfe, et, jme, msk, nge, sk, ste,
stge, tx, vge, axe, rue, udav, fwip, and all USB serial.
o Remove "legacy" devices: le, vx, dc, pcn, rl, sis.
Make sure to the module list is a superset of what goes into GENERIC.
- add some new hardware support for 82599
- Big change to interrupt architecture, it now
uses a queue which contains an RX/TX pair as
the recipient of the interrupt. This will reduce
overall system interrupts/msix usage.
- Improved RX mbuf handling: the old get_buf routine
is no longer synchronized with rxeof, this allows
the elimination of packet discards due to mbuf
allocation failure.
- Much simplified and improved AIM code, it now
happens in the queue interrupt context and takes
into account both the traffic on the RX AND TX
side.
- variety of small tweaks, like ring size, that have
been seen as performance improvements.
- Thanks to those that provided feedback or suggested
changes, I hope I've caught all of them.
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
Reviewed by: kib, jhb
shared and generalized between our current amd64, i386 and pc98.
This is just an initial step that should lead to a more complete effort.
For the moment, a very simple porting of cpufreq modules, BIOS calls and
the whole MD specific ISA bus part is added to the sub-tree but ideally
a lot of code might be added and more shared support should grow.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, kib, jhb, imp
Discussed on: arch
MFC: 3 weeks
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.
Also, eliminate some dead code and clean up in other places as part
of this quick once-over.
MFC after: 1 week
module. With r203732 it became apparent that creating the sysctl nodes
twice causes at least a warning, however the whole code shouldn't be
present twice in the first place.
Discussed with: rmacklem
o uses v4 firmware instead of v3. A port will be committed to create
the bwn firmware module.
o supports B/G and LP(low power) PHYs.
o supports 32 / 64 bits DMA operations.
o tested on big / little endian machines so should work on all
architectures.
It'd not connected to the build until the firmware port is committed.
Note that due to e.g. write throttling ('wdrain'), it can stall all the disk
I/O instead of just the device it's configured for. Using it for removable
media is therefore not a good idea.
Reviewed by: pjd (earlier version)
of Code 2009:
- BSDL block and inode allocation policies for ext2fs. This involves the use
FFS1 style block and inode allocation for ext2fs. Preallocation was removed
since it was GPL'd.
- Make ext2fs MPSAFE by introducing locks to per-mount datastructures.
- Fixes for kern/122047 PR.
- Various small bugfixes.
- Move out of gnu/ directory.
Sponsored by: Google Inc.
Submitted by: Aditya Sarawgi <sarawgi.aditya AT SPAMFREE gmail DOT com>
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
to list them all in the Makefile for the module,
otherwise it won't load due to missing symbols.
The problem only affected head with ipfw built as a module.
Reported by David Horn
The hardware is compliant with WDRT specification, so I originally
considered including generic WDRT watchdog support, but decided
against it, because I couldn't find anyone to the code for me.
WDRT seems to be not very popular.
Besides, generic WDRT porbably requires a slightly different driver
approach.
Reviewed by: des, gavin, rpaulo
MFC after: 3 weeks
long as I remember, and completely superseded by better maintained umass(4).
It's main idea was to optionally avoid CAM dependency for such devices, but
with move ATA to CAM, it is not actual any more.
No objections: hselasky@, thompsa@, arch@
* iwnfw has now been split into individual modules so autoloading of
firmware module(s) does work again.
* Changes have been made to RUN -> AUTH transition, this should fix the
issue reported by Glen and others.
* Brandon reported issues in iwn_cmd() with large commands, those have
been fixed to.
* DEAUTH is now handled correctly.
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.
Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
driver still, it generally works well for most people most of the
time. It is still too green for GENERIC, however.
Submitted by: many (latest being kwm@)
MFC after: 2 days (before RC1 if possible)
Unfortunately, the wrappers that are present in pts(4) don't have the
mechanics to allow pty(4) to be unloaded safely, so I'm forcing this kld
to return EBUSY. This also means we have to enable some extra code in
pts(4) unconditionally.
Proposed by: rwatson
replace it with wrappers around our taskqueue(9).
To make it possible implement taskqueue_member() function which returns 1
if the given thread was created by the given taskqueue.
Approved by: re (kib)
things a bit:
- use dpcpu data to track the ifps with packets queued up,
- per-cpu locking and driver flags
- along with .nh_drainedcpu and NETISR_POLICY_CPU.
- Put the mbufs in flight reference count, preventing interfaces
from going away, under INVARIANTS as this is a general problem
of the stack and should be solved in if.c/netisr but still good
to verify the internal queuing logic.
- Permit changing the MTU to virtually everythinkg like we do for loopback.
Hook epair(4) up to the build.
Approved by: re (kib)
Driver supports Serial ATA and ATAPI devices, Port Multipliers
(including FIS-based switching), hardware command queues (31 command
per port) and Native Command Queuing. This is probably the second on
popularity, after AHCI, type of SATA2 controllers, that benefits from
using CAM, because of hardware command queuing support.
Approved by: re (kib)
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
the PHYs as some PHY drivers use it (but probably shouldn't). How
gem(4) has worked with brgphy(4) on powerpc without this so far is
unclear to me.
- Introduce a dying flag which is set during detach and checked in
gem_ioctl() in order to prevent active BPF listeners to clear
promiscuous mode which may lead to the tick callout being restarted
which will trigger a panic once it's actually gone.
- In gem_stop() reset rather than just disable the transmitter and
receiver in order to ensure we're not unloading DMA maps still in
use by the hardware. [1]
- The blanking time is specified in PCI clocks so we should use twice
the value when operating at 66MHz.
- Spell some 2 as ETHER_ALIGN and a 19 as GEM_STATUS_TX_COMPLETION_SHFT
to make the actual intentions clear.
- As we don't unload the peak attempts counter ignore its overflow
interrupts.
- Remove a stale setting of a variable to GEM_TD_INTERRUPT_ME which
isn't used afterwards.
- For optimum performance increment the TX kick register in multiples
of 4 if possible as suggested by the documentation.
- Partially revert r164931; drivers should only clear the watchdog
timer if all outstanding TX descriptors are done.
- Fix some debugging strings.
- Add a missing BUS_DMASYNC_POSTWRITE in gem_rint().
- As the error paths in the interrupt handler are generally unlikely
predict them as false.
- Add support for the SBus version of the GEM controller. [2]
- Add some lock assertions.
- Improve some comments.
- Fix some more or less cosmetic issues in the code of the PCI front-end.
- Change some softc members to be unsigned where more appropriate and
remove unused ones.
Approved by: re (kib)
Obtained from: NetBSD (partially) [2], OpenBSD [1]
MFC after: 2 weeks
* Driver for ACPI HP extra functionations, which required
ACPI WMI driver.
Submitted by: Michael <freebsdusb at bindone.de>
Approved by: re
MFC after: 2 weeks
- remove mbuf iovec - useful, but adds too much complexity when isolated to
the driver
- remove driver private caching - insufficient benefit over UMA to justify
the added complexity and maintenance overhead
- remove separate logic for managing multiple transmit queues, with the
new drbr routines the control flow can be made to much more closely resemble
legacy drivers
- remove dedicated service threads, with per-cpu callouts one can get the same
benefit much more simply by registering a callout 1 tick in the future if there
are still buffered packets
- remove embedded mbuf usage - Jeffr's changes will (I hope) soon be integrated
greatly reducing the overhead of using kernel APIs for reference counting
clusters
- add hysteresis to descriptor coalescing logic
- add coalesce threshold sysctls to allow users to decide at run-time
between optimizing for forwarding / UDP or optimizing for TCP
- add once per second watchdog to effectively close the very rare races
occurring from coalescing
- incorporate Navdeep's changes to the initialization path required to
convert port and adapter locks back to ordinary mutexes (silencing BPF
LOR complaints)
- enable prefetches in get_packet and tx cleaning
Reviewed by: navdeep@
MFC after: 2 weeks
DP83065 Saturn Gigabit Ethernet controllers. These are the successors
of the Sun GEM controllers and still have a similar but extended transmit
logic. As such this driver is based on gem(4).
Thanks to marcel@ for providing a Sun Quad GigaSwift Ethernet UTP (QGE)
card which was vital for getting this driver to work on architectures
not using Open Firmware.
Approved by: re (kib)
MFC after: 2 weeks
controller. These controllers are also known as L1C(AR8131) and
L2C(AR8132) respectively. These controllers resembles the first
generation controller L1 but usage of different descriptor format
and new register mappings over L1 register space requires a new
driver. There are a couple of registers I still don't understand
but the driver seems to have no critical issues for performance and
stability. Currently alc(4) supports the following hardware
features.
o MSI
o TCP Segmentation offload
o Hardware VLAN tag insertion/stripping
o Tx/Rx interrupt moderation
o Hardware statistics counters(dev.alc.%d.stats)
o Jumbo frame
o WOL
AR8131/AR8132 also supports Tx checksum offloading but I disabled
it due to stability issues. I'm not sure this comes from broken
sample boards or hardware bugs. If you know your controller works
without problems you can still enable it. The controller has a
silicon bug for Rx checksum offloading, so the feature was not
implemented.
I'd like to say big thanks to Atheros. Atheros kindly sent sample
boards to me and answered several questions I had.
HW donated by: Atheros Communications, Inc.
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.
Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
adjust conf/files and modules' Makefiles accordingly.
No code or ABI changes so this and most of previous related
changes can be easily MFC'ed
MFC after: 5 days
includes support for NFSv4. The subsystem can optionally be linked
into the kernel using the two options:
NFSCL - the client
NFSD - the server
It is also built as three modules:
nfscl - the client
nfsd - the server
nfscommon - functions shared by the client and server
Approved by: kib (mentor)
- add FreeBSD implementation of xdrmem_control needed by zfs
- have zfs define xdr_ops using FreeBSD's definition
- remove solaris xdr files from zfs compile
get a quick snapshot of the kernel's symbol table including the symbols
from any loaded modules (the symbols are all merged into one symbol
table). Unlike like other implementations, this ksyms driver maps
memory in the process memory space to store the snapshot at the time
/dev/ksyms is opened. It also checks to see if the process has already
a snapshot open and won't allow it to open /dev/ksyms it again until it
closes first. This prevents kernel and process memory from being
exhausted. Note that /dev/ksyms is used by the lockstat(1) command.
Reviewed by: gallatin kib (freebsd-arch)
Approved by: gnn (mentor)
adds probes for mutexes, reader/writer and shared/exclusive locks to
gather contention statistics and other locking information for
dtrace scripts, the lockstat(1M) command and other potential
consumers.
Reviewed by: attilio jhb jb
Approved by: gnn (mentor)
about removing a few #ifdefs and providing compatibility wrappers and
VOP implementations to get and set an ACL; ZFS does ACL enforcement all
by itself.
Note that the VOPs are ifdefed out for now, so this change should be
a no-op.
Reviewed by: pjd
I really don't want any pieces of code to include ioctl_compat.h, so let
the ibcs2 and svr4 compat leave sgtty alone. If they want to support
sgtty, they should emulate it on top of termios, not sgtty.
The code has been marked with BURN_BRIDGES for a long time. ibcs2 and
svr4 are not really popular pieces of code anyway.
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
in sys/nfs/nfs_nfssvc.c by registering with it using the
nfsd_call_nfsserver function pointer. Also, add the build glue for
nfs_nfssvc.c optionally based on "nfsserver" and also as a loadable
module.
Submitted by: rmacklem
Reviewed by: kib
Approved by: kib (mentor)
The work have been under testing and fixing since then, and it is mature enough
to be put into HEAD for further testing.
A lot have changed in this time, and here are the most important:
- Gvinum now uses one single workerthread instead of one thread for each
volume and each plex. The reason for this is that the previous scheme was
very complex, and was the cause of many of the bugs discovered in gvinum.
Instead, gvinum now uses one worker thread with an event queue, quite
similar to what used in gmirror.
- The rebuild/grow/initialize/parity check routines no longer runs in
separate threads, but are run as regular I/O requests with special flags.
This made it easier to support mounted growing and parity rebuild.
- Support for growing striped and raid5-plexes, meaning that one can extend the
volumes for these plex types in addition to the concat type. Also works while
the volume is mounted.
- Implementation of many of the missing commands from the old vinum:
attach/detach, start (was partially implemented), stop (was partially
implemented), concat, mirror, stripe, raid5 (shortcuts for creating volumes
with one plex of these organizations).
- The parity check and rebuild no longer goes between userland/kernel, meaning
that the gvinum command will not stay and wait forever for the rebuild to
finish. You can instead watch the status with the list command.
- Many problems with gvinum have been reported since 5.x, and some has been hard
to fix due to the complicated architecture. Hopefully, it should be more
stable and better handle edge cases that previously made gvinum crash.
- Failed drives no longer disappears entirely, but now leave behind a dummy
drive that makes sure the original state is not forgotten in case the system
is rebooted between drive failures/swaps.
- Update manpage to reflect new commands and extend it with some examples.
Sponsored by: Google Summer of Code 2007
Mentored by: le
Tested by: Rick C. Petty <rick-freebsd2008 -at- kiwi-computer.com>
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
provider. The NFS client exposes 'start' and 'done' probes for NFSv2
and NFSv3 RPCs when using the new RPC implementation, passing in the
vnode, mbuf chain, credential, and NFSv2 or NFSv3 procedure number.
For 'done' probes, the error number is also available.
Probes are named in the following way:
...
nfsclient:nfs2:write:start
nfsclient:nfs2:write:done
...
nfsclient:nfs3:access:start
nfsclient:nfs3:access:done
...
Access to the unmarshalled arguments is not easily available at this
point in the stack, but the passed probe arguments are sufficient to
to a lot of interesting things in practice. Technically, these probes
may cover multiple RPC retransmits, and even transactions if the
transaction ID change as a result of authentication failure or a
jukebox error from the server, but usefully capture the intent of a
single NFS request, such as access, getattr, write, etc.
Typical use might involve profiling RPC latency by system call, number
of RPCs, how often a getattr leads to a call to access, when failed
access control checks occur, etc. More detailed RPC information might
best be provided by adding a krpc provider. It would also be useful
to add NFS client probes for events such as the access cache or
attribute cache satisfying requests without an RPC.
Sponsored by: Google, Inc.
MFC after: 1 month
