HNS3 PF driver only supports RSS, DCB or NONE multiple queues mode.
Currently, driver doesn't verify the VMDq multi-queue mode completely.
This patch fixes the verification for VMDq mode.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, "ONLY DCB" and "DCB+RSS" mode are both supported by HNS3
PF driver. But the driver verifies only the "DCB+RSS" multiple queues
mode.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Some mbx messages do not need to reply with data. In this case,
it is no need to set the response data address and the response
length.
This patch removes these redundant codes from mbx messages that do
not need be replied.
Fixes: a5475d61fa ("net/hns3: support VF")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Rx vector implementation depends on the mbuf fields
(such as rearm_data/rx_descriptor_fields1) layout, this patch adds
compile-time verification for this.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports check max SIMD bitwidth when choosing NEON and SVE
vector path.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the L3L4P/L3E/L4E/OL3E/OL4E fields in Rx descriptor used to
indicate hardware checksum result:
1. L3L4P: indicates hardware has processed L3L4 checksum for this
packet, if this bit is 1 then L3E/L4E/OL3E/OL4E is trustable.
2. L3E: L3 checksum error indication, 1 means with error.
3. L4E: L4 checksum error indication, 1 means with error.
4. OL3E: outer L3 checksum error indication, 1 means with error.
5. OL4E: outer L4 checksum error indication, 1 means with error.
Driver will set the good checksum flag through packet type and
L3E/L4E/OL3E/OL4E when L3L4P is 1, it runs as follows:
1. If packet type indicates it's tunnel packet:
1.1. If packet type indicates it has inner L3 and L3E is zero, then
mark the IP checksum good.
1.2. If packet type indicates it has inner L4 and L4E is zero, then
mark the L4 checksum good.
1.3. If packet type indicates it has outer L4 and OL4E is zero, then
mark the outer L4 checksum good.
2. If packet type indicates it's not tunnel packet:
2.1. If packet type indicates it has L3 and L3E is zero, then mark the
IP checksum good.
2.2. If packet type indicates it has L4 and L4E is zero, then mark the
L4 checksum good.
As described above, the good checksum calculation is time consuming,
it impacts the Rx performance.
By balancing performance and functionality, driver uses the following
scheme to set good checksum flag when L3L4P is 1:
1. If L3E is zero, then mark the IP checksum good.
2. If L4E is zero, then mark the L4 checksum good.
The performance gains are 3% in small packet iofwd scenarios.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports runtime config of mask device capability, it was
used to mask the capability which queried from firmware.
The device argument key is "dev_caps_mask" which takes hexadecimal
bitmask where each bit represents whether mask corresponding capability.
Its main purpose is to debug and avoid problems.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng 930 uses a new RAS exception reporting solution.
The reset type and exception status are reported through
firmware. The driver modifies the corresponding code to
adapt to the new solution.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
'HNS3_RXD_TSIND_S' and 'HNS3_RXD_TSIND_M' is unused, which should
be deleted.
This patch fixed it.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, user could use runtime config "rx_func_hint=simple" to
select the hns3_recv_pkts API, but the API's name get from
rte_eth_rx_burst_mode_get is "Scalar" which has not reflected "simple".
So this patch renames hns3_recv_pkts to hns3_recv_pkts_simple, and
also change it's name which gets from rte_eth_rx_burst_mode_get to
"Scalar Simple" to maintain conceptual consistency.
Fixes: 521ab3e933 ("net/hns3: add simple Rx path")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds the configuration of fixed speed for the PF device.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
If the flow control auto-negotiation is not supported and the flow
control modes on the local and link partner is asymmetric, the flow
control on the NIC does not take effect. The support of the
auto-negotiation capability requires the cooperation of the firmware
and driver.
This patch supports the flow control auto-negotiation only for copper
port. For optical ports, the forced flow control mode is still used.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports link speed auto-negotiation for PF. If the
device supports auto-negotiation, the device negotiates with
the link partner at all speeds supported by the device.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The speed capability of the device can be reported to the upper-layer app
in rte_eth_dev_info_get API. In this API, the speed capability is derived
from the 'supported_speed', which is the speed capability actually
supported by the NIC. The value of the 'supported_speed' is obtained
once in the probe stage and may be updated in the scheduled task to deal
with the change of the transmission interface.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the speed of fiber port is obtained by using the default
query type of HNS3_OPC_GET_SFP_INFO opcode. In this way, only
the speed of the optical module can be obtained. In fact, the opcode
also supports an active query type, which is a channel for obtaining
information such as the speed, the supported speed, auto-negotiation
capability, and FEC mode. This patch changes the query type of the
opcode from the default query type to the active query type to obtain
the supported speed of fiber port.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The firmware compatibility configuration in PF driver is used to
maintain the compatibility of some features of the driver and
firmware, and requires firmware to enable these features. Currently,
the configuration is in hns3_init_hardware(), which is a little back.
Because firmware may clear some configurations (such as, MAC related)
after receiving the command. And firmware can not be aware of some
default initializations (such as, flow control) before executing the
command to set the copper PHY when the PHY is controlled by firmware.
Therefore, it is recommended that no other hardware resources are
configured before the compatibility configuration. And it should be
moved to hns3_cmd_init(), which is responsible for the firmware
command initialization of driver.
In addition, the driver needs to perform corresponding processing
if the command fails to be sent.
1) If firmware fails to take over the copper PHY, the copper port fails
to initialize.
2) If fails to enable the report of link events, the device does not
support the LSC capability.
Fixes: bff6ebfe30d4 ("net/hns3: refactor PF LSC event report")
Fixes: bac6a06441 ("net/hns3: fix link status change from firmware")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, hns3 driver doesn't support to flow control auto-negotiation.
The FC mode requested by user is the same as the current FC mode. It is
not necessary to maintain the current FC mode. We only report the current
FC mode based on actual flow control mode in hns3_flow_ctrl_get().
This patch removes this redundant field. In addition, "requested_mode" in
hns3_hw struct indicates the FC mode requested by user, and the name is
unreasonable. It needs to be modified to "requested_fc_mode".
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The bit(5) of supported, advertising and lp_advertising for copper
PHYs obtained from the firmware indicates 1000M full-duplex. This
speed capability bit is missing in the current codes.
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The "supported capability" obtained from firmware on copper ports
includes the speed capability, auto-negotiation capability, and flow
control capability. Therefore, this patch changes "supported_capa" to
"supported_speed" and parses the speed capability supported by the
driver from the "supported capability".
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In the previous patch, driver will calculate packet type by ignoring
VLAN information because the packet type may calculate error when
exist VLAN and VLAN strip.
So here remove the following ptypes from support list:
1) RTE_PTYPE_L2_ETHER_VLAN
2) RTE_PTYPE_L2_ETHER_QINQ
3) RTE_PTYPE_INNER_L2_ETHER_VLAN
4) RTE_PTYPE_INNER_L2_ETHER_QINQ
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng 930 supports RXD advanced layout. If enabled the layout, the
hardware will report packet type by 8-bit PTYPE filed in the Rx
descriptor, and the supported ptypes are different from original
scheme. So this patch adds supported list for RXD advanced layout.
Fixes: fb5e906940 ("net/hns3: support Rx descriptor advanced layout")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The PTP depends on special packet type reported by hardware which
enabled rxd advanced layout, so if the hardware doesn't support rxd
advanced layout, driver should ignore the PTP capability.
Fixes: 4387523581 ("net/hns3: get device capability from firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports reporting TUNNEL GRE packet type when rxd advanced
layout enabled.
Fixes: fb5e906940 ("net/hns3: support Rx descriptor advanced layout")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch adds RTE_PTYPE_L4_UDP flag when parsed tunnel vxlan packet.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The type of return value of hns3_cmd_send is int, some function declare
the return value as hns3_cmd_status.
This patch fix the incorrect use of the enum hns3_cmd_status.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Fixes: 02a7b55657 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, when processing MBX messages, the system timestamp is obtained
to determine whether timeout occurs. However, the gettimeofday function
is not monotonically increasing. Therefore, this may lead to incorrect
judgment or difficulty exiting the loop. And actually, in this scenario,
it is not necessary to obtain the timestamp.
This patch deletes the call to the gettimeofday function during MBX
message processing.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
VF will build two queues (csq: command send queue, crq: command receive
queue) with firmware, the crq may contain the following messages:
1) mailbox response message which was the ack of mailbox sync request.
2) PF's link status change message which may send by PF at anytime;
Currently, any threads in the primary and secondary processes could
send mailbox sync request, so it will need to process the crq messages
in there own thread context.
If the crq hold two messages: a) PF's link status change message, b)
mailbox response message when secondary process deals with the crq
messages, it will lead to report lsc event in secondary process
because it uses the policy of processing all pending messages at once.
We use the following scheme to solve it:
1) threads in secondary process could only process specifics messages
(eg. mailbox response message) in crq, if the message processed, its
opcode will rewrite with zero, then the intr thread in primary
process will not process again.
2) threads other than intr thread in the primary process use the same
processing logic as the threads in secondary process.
3) intr thread in the primary process could process all messages.
Fixes: 76a3836b98 ("net/hns3: fix setting default MAC address in bonding of VF")
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the mailbox synchronous communication between VF and PF use
the following fields to maintain communication:
1. Req_msg_data which was combined by message code and subcode, used to
match request and response.
2. Head which means the number of requests successfully sent by VF.
3. Tail which means the number of responses successfully received by VF.
4. Lost which means the number of requests which are timeout.
There may possible mismatches of the following situation:
1. VF sends message A with code=1 subcode=1.
Then head=1, tail=0, lost=0.
2. PF was blocked about 500ms when processing the message A.
3. VF will detect message A timeout because it can't get the response
within 500ms.
Then head=1, tail=0, lost=1.
4. VF sends message B with code=1 subcode=1 which equal message A.
Then head=2, tail=0, lost=1.
5. PF processes the first message A and send the response message to VF.
6. VF will update tail field to 1, but the lost field will remain
unchanged because the code/subcode equal message B's, so driver will
return success because now the head(2) equals tail(1) plus lost(1).
This will lead to mismatch of request and response.
To fix the above bug, we use the following scheme:
1. The message sent from VF was labelled with match_id which was a
unique 16-bit non-zero value.
2. The response sent from PF will label with match_id which got from the
request.
3. The VF uses the match_id to match request and response message.
This scheme depends on the PF driver, if the PF driver don't support
then VF will uses the original scheme.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, driver will copy mailbox messages body into arq ring when
process HNS3_MBX_LINK_STAT_CHANGE and HNS3_MBX_LINK_STAT_CHANGE
message, and then call hns3_mbx_handler API which will direct process
pre-copy messages. In the whole process, the arq ring don't have a
substantial effect.
Note: The arq ring is designed for kernel environment which could not
do much job in interrupt context, but for DPDK it's not required.
Also we rename hns3_handle_link_change_event to
hns3pf_handle_link_change_event which add 'pf' suffix to make it
better to distinguish.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, after the reset is complete, the PMD restores the FEC
according to the FEC configuration reserved in the driver. If there is a
concurrency between the FEC setup operation and the restore operation
after a reset, the FEC status of the last hardware may be unknown.
This patch adds the step of obtaining the lock when setting the FEC to
avoid concurrency between restore operation and setting operation.
Fixes: 9bf2ea8dbc ("net/hns3: support FEC")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
At the end of the reset, the state of queues need to be restored
according to the states saved in the driver. If the start and stop
operations of the queues are concurrent at this time, it may cause the
final status to be uncertain.
This patch requires queues to acquire the hw lock before starting and
stopping. If the device is being restored due to reset at this time, it
will block until the reset is completed.
Fixes: fa29fe45a7 ("net/hns3: support queue start and stop")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
During the task queue pairs reset, the getimeofday is used to obtain the
timestamp to determine whether the command execution times out. But
gettimeofday is not monotonous, it can be modified by system
administrators, so the timing may not be accurate or even cause the loop
to wait consistently.
And actually, in this scenario, it is not necessary to obtain the
timestamp.
This patch removes the operation of obtaining the timestamp from the task
queue pairs reset function.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the packet type calculated by
vlan/ovlan/l3id/l4id/ol3id/ol4id fields have the following problems:
1) Identify error when exist VLAN strip which will lead to the data
buffer has non VLAN header but mbuf's ptype have L2_ETHER_VLAN flag.
2) Some packet identifies error, eg: hardware report it's RARP or
unknown packet, but ptype will marked with L2_ETHER .
So driver will calculate packet type only by l3id/l4id/ol3id/ol4id
fields.
Fixes: 0e98d5e6d9 ("net/hns3: fix packet type report in Rx")
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, if RAS interrupt and FLR occurred at the same time, FLR will
be detected and corresponding schedule state will be set during RAS
interrupt processing. However, the schedule state value will be
overridden in subsequent RAS processing, resulting in FLR processing
failure. This patch solves this problem.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch adds rollback processing when updating imissed
stats failed in PF init.
Fixes: 3e9f3042d7 ("net/hns3: add imissed packet stats")
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, there are four control variables (rx_simple_allowed,
rx_vec_allowed, tx_simple_allowed and tx_vec_allowed) which are used
to impact the selection of Rx/Tx burst function.
The purpose of the design is to provide a way to control the selection
of Rx/Tx burst function by modifying it's values, but these variables
have no entry to modify unless make intrusive modifications.
Now we already support runtime config to select Rx/Tx function, these
variables could be removed.
Fixes: a124f9e959 ("net/hns3: add runtime config to select IO burst function")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch adds debug info for Rx/Tx burst function which was choosing.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, PF driver will report lsc when it detects the link status
change, it's not a generic implementation.
We refactor PF lsc event report by following scheme:
1. PF driver marks RTE_PCI_DRV_INTR_LSC in rte_pci_driver by default.
2. In the init stage, PF driver will detect whether firmware supports
lsc interrupt or not, driver will clear RTE_ETH_DEV_INTR_LSC flag if
firmware doesn't support lsc interrupt.
3. PF driver will report lsc event only when dev_conf.intr_conf.lsc is
set.
Note: If the firmware supports lsc interrupt, we also keep periodic
polling to deal with the interrupt loss.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, VF driver periodically obtains link status from PF kernel
driver, and reports lsc event when detects link status change. Because
the period is 1 second, it's probably too late to report especially
in such as bonding scenario.
To solve this problem we use the following scheme:
1. PF kernel driver support immediate push link status to all VFs when
it detects the link status changes.
2. VF driver will detect PF kernel driver whether support push link
status in device init stage by sending request link info mailbox
message to PF, PF then tell VF the push capability by extend
HNS3_MBX_LINK_STAT_CHANGE mailbox message.
3. VF driver marks RTE_PCI_DRV_INTR_LSC in rte_pci_driver by default,
when it detects PF doesn't support push link status then it will clear
RTE_ETH_DEV_INTR_LSC flag.
So if PF kernel driver supports push link status to VF, then VF driver
will have RTE_ETH_DEV_INTR_LSC capability.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Add one space before the left brace to solve the static warning.
Fixes: 63e05f19b8 ("net/hns3: support Rx descriptor status query")
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Delete redundant blank line in "hns3vf_check_event_cause" to
solve the static warning.
Fixes: a5475d61fa ("net/hns3: support VF")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Support get device version which is equal to the firmware version
when dump register.
Fixes: 936eda25e8 ("net/hns3: support dump register")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the VF mailbox synchronization communication is based on
three fields: head/tail/lost, when head equals tail plus lost, it
means the response is received successfully.
The head field indicates the number of requests that are successfully
sent. If the request sending fails, it should not be updated.
This patch fix the above bug by roll back updates when the sending
fails.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
User could create flow rules with specified counter by the action of
RTE_FLOW_ACTION_TYPE_COUNT, but the counter may retain the original
value when create.
This patch fix the bug by read the counter when creating the rule
because the counter is read-clear.
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In multi-TC scenarios, MAC pause is not supported. Otherwise, only
TC0 can trigger pause frames, and other TCs cannot trigger pause
frames. In this case, flow control does not meet the expectation.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, three hardware operations are involved in setting the PVID.
If any operation fails, a failure will be returned. And there may be
residual hardware configurations because no rollback is performed.
This patch adds rollback operation for setting PVID to avoid residual
hardware configuration after the PVID fails to be configured.
Fixes: 411d23b9ea ("net/hns3: support VLAN")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
When FLR occurs, the head pointer register of
the command queue will be cleared, resulting in
abnormal detection of the head pointer register
of the command queue. At present, FLR is detected
in this way, and the reset recovery process is
executed.
However, when FLR occurs, the header pointer
register of the command queue is not necessarily
abnormal. For example, when the driver runs
normally, the value of the header pointer register
of the command queue may also be 0, which will
lead to the miss detection of FLR.
Therefore, the judgment that whether the base
address register of command queue is 0 is added
to ensure that FLR not miss detection.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
When start testpmd with two hns3 VFs(0000:bd:01.0, 0000:bd:01.7), and
then execute the following commands:
testpmd> create bonded device 1 0
testpmd> set bonding mac_addr 2 3c:12:34:56:78:9a
testpmd> add bonding slave 0 2
testpmd> add bonding slave 1 2
testpmd> set portmask 0x4
testpmd> port start 2
It will occurs the following error in a low probability:
0000:bd:01.0 hns3_get_mbx_resp(): VF could not get mbx(3,0)
head(16) tail(15) lost(1) from PF in_irq:0
0000:bd:01.0 hns3vf_set_default_mac_addr(): Failed to set mac
addr(3C:**:**:**:78:9A) for vf: -62
mac_address_slaves_update(1541) - Failed to update port Id 0
MAC address
The problem replay:
1. The 'port start 2' command will start slave ports and then set slave
mac address, the function call flow: bond_ethdev_start ->
mac_address_slaves_update.
2. There are also a monitor task which running in intr thread will check
slave ports link status and update slave ports mac address, the
function call flow: bond_ethdev_slave_link_status_change_monitor ->
bond_ethdev_lsc_event_callback -> mac_address_slaves_update.
3. Because the above step1&2 running on different threads, they may both
call drivers ops mac_addr_set which is hns3vf_set_default_mac_addr.
4. hns3vf_set_default_mac_addr will first acquire hw.lock and then send
mailbox to PF and wait PF's response message. Note: the PF's
response is an independent message which will received in hw.cmq.crq,
the receiving operation can only performed in intr thread.
5. So if the step1 operation hold the hw.lock and try get response
message, and step2 operation try acquire the hw.lock and so it can't
process the response message, this will lead to step1 fail.
The solution:
1. make all threads could process the mailbox response message, which
protected by the hw.cmq.crq.lock.
2. use the following rules to avoid deadlock:
2.1. ensure use the correct locking sequence: hw.lock >
hw.mbx_resp.lock > hw.cmq.crq.lock.
2.2. make sure don't acquire such as hw.lock & hw.mbx_resp.lock again
when process mailbox response message.
Fixes: 463e748964 ("net/hns3: support mailbox")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
PHY is a common concept for the copper and optical media type interface.
There are some inappropriate function names for copper ports, which
needs to be adjusted.
Fixes: 2e4859f3b3 ("net/hns3: support PF device with copper PHYs")
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch updates copyright date for hns3 PMD files.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
There are two APIs in ethdev layer to get link status of device, namely,
"rte_eth_link_get" and "rte_eth_link_get_nowait". When the device link
is unstable or auto-negotiation is in progress, the first API supports
the function of waiting for the NIC to link up, and the maximum waiting
time is 9 seconds based on DPDK Documentation. For the hns3 PMD driver,
the link can be established within 2 seconds.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
According to the suggestion of our legal department,
to standardize the copyright license of our code to
avoid potential copyright risks, we make a unified
modification to the "Hisilicon", which was nonstandard,
in the main modules we maintain.
We change it to "HiSilicon", which is consistent with
the terms used on the following official website:
https://www.hisilicon.com/en/terms-of-use.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch fixed cyclomatic complexity about MTU
in device configure process.
Fixes: 1f5ca0b460 ("net/hns3: support some device operations")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the queue reset process needs to be performed one by one,
which is inefficient. However, the queues reset in the same function is
almost at the same stage. To optimize the queue reset process, a new
function has been added to the firmware command HNS3_OPC_CFG_RST_TRIGGER
to reset all queues in the same function at a time. And the related
queue reset MBX message is adjusted in the same way too.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
In the "hns3_dev_link_update" API, the link information of the port is
obtained first, and then 'dev_link' in dev->data is updated. When the
driver is resetting or fails to obtain link info, the current driver
still reports the previous link info to the user. This may cause that
the dev->data->dev_link may be inconsistent with the hw link status.
Therefore, the link status consistency between the hardware, driver,
and framework can be ensured in this interface regardless of whether
the driver is normal or abnormal.
Fixes: 109e4dd1bd ("net/hns3: get link state change through mailbox")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
For Kunpeng920 network engine, UDP packets with destination port 6081,
4789 or 4790 will be identified as tunnel packets. If the UDP CKSUM
offload is set in the mbuf, and the TX tunnel mask is not set, the
CKSUM of these packets will be wrong. In this case, the upper layer
user may not identify the packet as a tunnel packet, and processes it
as non-tunnel packet, and expect to offload the outer UDP CKSUM, so
they may not fill the outer L2/L3 length to mbuf. However, the HW
identifies these packet as tunnel packets and therefore offload the
inner UDP CKSUM. As a result, the inner and outer UDP CKSUM are
incorrect. And for non-tunnel UDP packets with preceding special
destination port will also exist similar checksum error.
For the new generation Kunpeng930 network engine, the above errata
have been fixed. Therefore, the concept of udp_cksum_mode is
introduced. There are two udp_cksum_mode for hns3 PMD,
HNS3_SPECIAL_PORT_HW_CKSUM_MODE means HW could solve the above
problem. And in HNS3_SPECIAL_PORT_SW_CKSUM_MODE, hns3 PMD will check
packets in the Tx prepare and perform the UDP CKSUM for such packets
to avoid a checksum error.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, if the PKT_TX_TCP_SEG and PKT_TX_TCP_CKSUM offload flags set
in the same time, hns3 PMD can not process the descriptors correctly.
This patch fixes it by adding the processing of this situation.
Fixes: fb6eb9009f ("net/hns3: fix Tx checksum with fixed header length")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The 'queue_full_cnt' stats have been encapsulated in 'dfx_stats'.
However, the modification in the SVE algorithm is omitted.
As a result, the driver fails to be compiled when the SVE
algorithm is used.
Fixes: 9b77f1fe30 ("net/hns3: encapsulate DFX stats in datapath")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
There may be a case in future that the speed obtained from firmware
is undefined (such as, 400G or other rate), and link status of device is
up. At this case, PMD driver will reports 100Mbps to the user in the
"hns3_dev_link_update" API, which is unreasonable. Besides, if the
speed from firmware is zero, driver should report zero instead of
100Mbps.
Fixes: 59fad0f321 ("net/hns3: support link update operation")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Since rte_flow is the only API for filtering operations,
the legacy driver interface filter_ctrl was too much complicated
for the simple task of getting the struct rte_flow_ops.
The filter type RTE_ETH_FILTER_GENERIC and
the filter operarion RTE_ETH_FILTER_GET are removed.
The new driver callback flow_ops_get replaces filter_ctrl.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add support for query Rx descriptor status in hns3 driver. Check the
descriptor specified and provide the status information of the
corresponding descriptor.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Add support for query Tx descriptor status in hns3 driver. Check the
descriptor specified and provide the status information of the
corresponding descriptor.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch added function level imissed stats for PF and VF. In
Kunpeng920, imissed is supported, only including RPU drop stats in PF.
In kunpeng930, imissed is supported,including RPU drop stats and SSU
drop stats in PF.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The current RAS code stores the reported RAS statistics in xstats.
This part of statistics is of little use in practice, and because
of the change of RAS scheme on Kunpeng930, the driver can not
obtain the RAS information any more, so this patch delete these
redundant RAS statistics.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Adjust the format of hns3 RAS related structures to resolve
the static check warnings.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng930 support outer UDP cksum, this patch add support for it.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the driver support multiple IO burst function and auto
selection of the most appropriate function based on offload
configuration.
Most applications such as l2fwd/l3fwd don't provide the means to
change offload configuration, so it will use the auto selection's io
burst function.
This patch support runtime config to select io burst function, which
add two config: rx_func_hint and tx_func_hint, both could assign
vec/sve/simple/common.
The driver will use the following rules to select io burst func:
a. if hint equal vec and meet the vec Rx/Tx usage condition then use the
neon function.
b. if hint equal sve and meet the sve Rx/Tx usage condition then use the
sve function.
c. if hint equal simple and meet the simple Rx/Tx usage condition then
use the simple function.
d. if hint equal common then use the common function.
e. if hint not set then:
e.1. if meet the vec Rx/Tx usage condition then use the neon function.
e.2. if meet the simple Rx/Tx usage condition then use the simple
function.
e.3. else use the common function.
Note: the sve Rx/Tx usage condition based on the vec Rx/Tx usage
condition and runtime environment (which must support SVE).
In the previous versions, driver will preferred use the sve function
when meet the sve Rx/Tx usage condition, but in this case driver could
get better performance if use the neon function.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the hns3 statistics may be inaccurate due to the
following two problems:
1. Queue-level statistics are read from the firmware, and only one Rx or
Tx can be read at a time. This results in a large time interval
between reading multiple queues statistics in a stress scenario, such
as 1280 queues used by a PF or 256 functions used at the same time.
Especially when the 256 functions are used at the same time, the
interval between every two firmware commands in a function can be
huge, because the scheduling mechanism of the firmware is similar to
RR.
2. The current statistics are read by type. The HW statistics are read
first, and then the software statistics are read. Due to preceding
reasons, HW reading may be time-consuming, which cause a
synchronization problem between SW and HW statistics of the same
queue.
In this patch, queue-level statistics are directly read from the bar
instead of the firmware, and all the statistics of a queue include HW
and SW are read at a time to reduce inconsistency.
Fixes: 8839c5e202 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
TNL is the abbreviation of tunnel, which means port
here. MAC TNL interrupt indicates the MAC status
report of the network port, which will be generated
when the MAC status changes.
This patch enables MAC TNL interrupt reporting, and
queries and prints the corresponding MAC status when
the interrupt is received, then clear the MAC interrupt
status. Because this interrupt uses the same interrupt
as RAS, the interrupt log is adjusted.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The mbufs of rx queue will be allocated in "hns3_do_start" function.
But these mbufs are not released when "hns3_dev_start" executes
failed.
Fixes: c4ae39b2cf ("net/hns3: fix Rx interrupt after reset")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
All input parameters in the "hns3_dev_xstats_get_by_id" API are used,
so the rte_unused flag of some variables should be deleted.
Fixes: 3213d584b6 ("net/hns3: fix xstats with id and names")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
After MTU changed, the buffer used to store packets in HW should be
reallocated. And buffer size is allocated based on the maximum frame
size in the PF struct. However, the value of maximum frame size is
not updated in time when MTU is changed. This would lead to a packet
loss for not enough buffer.
This patch update the maximum frame size before reallocating the HW
buffer. And a rollback operation is added to avoid the side effects
of buffer reallocation failures.
Fixes: 1f5ca0b460 ("net/hns3: support some device operations")
Fixes: d51867db65 ("net/hns3: add initialization")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, the driver get packet type by parse the
L3_ID/L4_ID/OL3_ID/OL4_ID from Rx descriptor and then lookup multiple
tables, it's time consuming.
Now Kunpeng930 support advanced RXD layout, which:
1. Combine OL3_ID/OL4_ID to 8bit PTYPE filed, so the driver get packet
type by lookup only one table. Note: L3_ID/L4_ID become reserved
fields.
2. The 1588 timestamp located at Rx descriptor instead of query from
firmware.
3. The L3E/L4E/OL3E/OL4E will be zero when L3L4P is zero, so driver
could optimize the good checksum calculations (when L3E/L4E is zero
then mark PKT_RX_IP_CKSUM_GOOD/PKT_RX_L4_CKSUM_GOOD).
Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by default.
This patch only provides basic function: identify and enable the RXD
advanced layout, and lookup ptype table if supported.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The normal operation of devices with copper phys depends on the
initialization and configuration of the PHY chip. The task of
driving the PHY chip is implemented in some firmware versions.
If firmware supports the phy driver, it will report a capability
flag to driver in probing process. The driver determines whether
to support PF device with copper phys based on the capability bit.
If supported, the driver set a flag indicating that the firmware
takes over the PHY, and then the firmware initializes the PHY.
This patch supports the query of link status and link info, and
existing basic features for PF device with copper phys.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The configuration operation for PHY is implemented by firmware. And
a capability flag will be report to driver, which means the firmware
supports the PHY driver. However, the current implementation only
supports obtaining the capability bit, but some basic functions of
copper ports in driver, such as, the query of link status and link
info, are not supported.
Therefore, it is necessary for driver to set the copper capability
bit to zero when the firmware supports the configuration of the PHY.
Fixes: 4387523581 ("net/hns3: get device capability from firmware")
Fixes: 95e5032586 ("net/hns3: support copper media type")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
When rate of port changes, the rate limit of the port needs to
be updated. So it is necessary to encapsulate an interface that
configures the rate limit based on the rate.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch implement Rx imissed stats by querying cmdq.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
In current HNS3 PMD, Rx/Tx bytes from packet stats are not
implemented.
This patch implemented Rx/Tx bytes using soft counters.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch add support tx_done_cleanup ops, which could support for
the API rte_eth_tx_done_cleanup to free consumed mbufs on Tx ring.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch makes more registers dumped in the dump_reg API to help
locate the fault.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch add support for dumping module EEPROM.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Replace copies of size(arr)/size(arr[0]) with RTE_DIM().
Eventually all of these macro definitions should be removed.
Signed-off-by: Andrew Boyer <aboyer@pensando.io>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When jumbo frame is enabled, the MTU size needs to be modified
based on 'max_rx_pkt_len'. Driver needs to check the validity
of 'max_rx_pkt_len'. And it should be in the range of
HNS3_DEFAULT_FRAME_LEN and HNS3_MAX_FRAME_LEN. Otherwise, it may
cause that the MTU size is inconsistent with jumbo frame offload.
Fixes: 19a3ca4c99 ("net/hns3: add start/stop and configure operations")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, during the VF reset, the VF will send a MBX to inform
PF to reset it and the disable command bit will be set whether
the MBX is successful. Generally, multiple reset attempts are made
after a failure. However, because the command is disabled, all
subsequent reset will all fail.
This patch disable the command only after the MBX message is
successfully.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
There are two scenarios that command queue uninit performed
concurrently with the firmware command: asynchronous command
and timeout command.
For asynchronous command, if a large number of functions send
commands, these commands may need to be queued to wait for
firmware processing. If a function is uninited suddenly, CMDQ
clearing and firmware processing may be performed concurrently.
For timeout command, if the command failed due to busy scheduling
of firmware, this command will be processed in the next scheduling.
And this may lead to concurrency.
The preceding concurrency may lead to a firmware exceptions.
This patch add a waiting time to ensure the firmware complete the
processing of left over command when PMD uninit.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
After FD rule config success, driver will malloc fdir_rule to hold the
rule info, if malloc fail the FD rule in hardware was not cleanup.
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Replace all the atomic type with C11 atomic builtins in hns3
PMD.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, statistics may overflow in some scenarios.
For example, if HW statistics are reset by stats reset operation,
but there are still a lot of residual packets exist in the HW
queues and these packets are error packets, flip may occurred
because the ipacket is obtained by subtracting the number of
software error packets from the number of HW received packets.
This patch verifies the calculation and returns 0 when overflow
may occur.
Fixes: 8839c5e202 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The Kunpeng920 and Kunpeng930 don't support parse MPLS packet, so
remove the type from supported flow items.
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
User could config Port or TC's peak rate by TM ops, but hardware does
not support peak rate which lower than 1Mbps. So we constraint TM
peak rate must be at least 1Mbps.
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The driver should not use the fixed value as the validity check of
RSS indirection table size with HW supported. As a result, it will
cause misjudgment when the RSS RETA size with HW supported have
changed.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
When the hardware link status changes, the firmware proactively
reports the link status change message, and then driver update
link status. This feature is lack of a switch to control in PF
driver. Otherwise, this feature does not take effect when the
kernel PF driver that supports the feature is not loaded.
Fixes: 109e4dd1bd ("net/hns3: get link state change through mailbox")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
When link information is updated in the firmware, the link information
is updated first and then the link status is updated. In a 1s periodic
task, PF driver queries the link information and then obtains link
status.
It may lead to a 1s time difference for obtaining valid link information
when the port is up. Therefore, the query order of driver should be
reversed to the order of firmware.
Fixes: 109e4dd1bd ("net/hns3: get link state change through mailbox")
Fixes: 59fad0f321 ("net/hns3: support link update operation")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch support LSC (Link Status Change) event report.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Here uses %d as printing output for enumeration member.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Rename some function about RSS implement functions
in order to make the functions naming style more
reasonable and consistency.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
For Kunpeng930, the NIC engine support 1280 tqps being taken over by
a PF. In this case, a maximum of 1281 interrupt resources are also
supported in this PF. To support the maximum number of queues, several
patches are made. But the interrupt related modification are missing.
So, in RX interrupt mode, a large number of queues will be aggregated
into one interrupt due to insufficient interrupts. It will lead to
waste of interrupt resources and reduces usability.
To utilize all these interrupt resources, related IMP command has been
extended. And, the I/O address of the extended interrupt resources are
different from the existing ones. So, a function used for calculating
the address offset has been added.
Fixes: 76d794566d ("net/hns3: maximize queue number")
Fixes: 27911a6e62 ("net/hns3: add Rx interrupts compatibility")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
The secondary process is applied a memory for the process_private
during initialization. Therefore, the memory needs to be released
when exiting.
Fixes: c203571b36 ("net/hns3: register and add log interface")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Here encapsulate the process code of the imp reset report and
global reset report into function in order to reduce the
complexity of the hns3_check_event_cause function.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
When parse flow director with all types, it needs to judge the spec
of item and mask of item for all packet types. The judgement is the
same for all types. Therefore, we move it into the concentrated
location.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch reconstruct the Rx interrupt map to reduce the cyclic
complexity and improve readability and maintainability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Here moves some judgement conditions to a separated function
for parsing IPv4 hdr and TCP hdr in hns3_parse_normal function.
Also, move the check of the selected input tuple of RSS to a
separated functions named hns3_rss_input_tuple_supported
in order to enhance scalability and complexity.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Use errno array instead of switch-case for refactor
the hns3_cmd_convert_err_code function.
Besides, we add a type for ROH(RDMA Over HCCS) check
cmdq return error in Kunpeng930 NIC hardware.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
One of the hot discussions in community recently was moving queue stats
to xstats. In this solution, a temporary
'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS' device flag is created to implement
the smooth switch. And the first half of this work has been completed in
the ethdev framework. Now driver needs to remove the flag from the
driver initialization process and does the rest of work.
For better readability and reasonability, per-queue stats also should be
cleared when rte_eth_stats is cleared. Otherwise, the sum of one item in
per-queue stats may be greater than corresponding item in rte_eth_stats.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
pkt_len_errors and l2_errors in Rx datapath indicate that driver
needs to discard received packets. And driver does not discard
packets for l3/l4/ol3/ol4_csum_errors in Rx datapath and others
stats in Tx datapath. Therefore, it is necessary for improving
code readability and maintainability to encapsulate error stats
and dfx stats.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The rte_ethdev_driver.h, rte_ethdev_vdev.h and rte_ethdev_pci.h files are
for drivers only and should be a private to DPDK and not installed.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Steven Webster <steven.webster@windriver.com>
The default RSS key does not need to be configured repeatedly
when call hns3_dev_configure function with the NULL RSS key
because the default RSS key has been configured when the PMD
driver run hns3_do_start function with starting device.
Besides, it will not overwrite the initialized key if
rte_eth_dev_configure API will be called directly and RSS key is NULL
after init PMD driver.
Therefore, the assignment for RSS key in hns3_dev_configure
function is unnecessary.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, when dump the queue interrupt registers, the number of
registers that should be dumped is calculated from num_msi. But the
value of num_msi includes the number of misc interrupts. So, for some
hardware version, like kupeng930, it will lead to an illegal access.
This patch replace num_msi with intr_tqps_num which indicate the
number of interrupts used by the tqps.
Fixes: 936eda25e8 ("net/hns3: support dump register")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The data pointer has not moved after BAR register dumped. This causes
the later register to overwrite the previous data.
This patch fix the overwriting by move the pointer after every dump
function. And the missing separator between 32-bit register and the
64-bit register is also added to avoid a parsing error.
Fixes: 936eda25e8 ("net/hns3: support dump register")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, the reg length return by HNS3 is the total length of all the
registers. But for upper layer user, the total register length is the
length multiplied by width. This can lead to a waste of memory and print
some invalid information.
This patch corrects the length and width of the register.
Fixes: 936eda25e8 ("net/hns3: support dump register")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The original command opcode '0x700A' may cause firmware error,
so '0x700A' is deserted, now use '0x700B' to replace it.
Fixes: 223d9eceae ("net/hns3: clear residual hardware configurations on init")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Current hns3vf queried link status in dev init stage, but the link
status should be maintained in dev start stage, this patch fix this.
Also, in the dev start stage, we use quick query instead of delayed
query to make sure update the link status soon.
Fixes: a5475d61fa ("net/hns3: support VF")
Fixes: 958edf6627 ("net/hns3: fix VF link status")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch support RTE TM ops function for PF, which could
used to:
1. config port's peak rate.
2. config TC's peak rate.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Use C11 atomic builtins with explicit ordering instead of
rte_atomic ops with the resetting member of hns3_reset_data
structure.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The jumbo frame uses the 'RTE_ETHER_MAX_LEN' as boundary condition,
but the Ether overhead is larger than 18 when it supports dual VLAN tags.
That will cause the jumbo flag rx offload is wrong when MTU size is
'RTE_ETHER_MTU'.
This fix will change the boundary condition with 'HSN3_DEFAULT_FRAME_LEN',
that perhaps impacts the cases of the jumbo frame related.
Fixes: 1f5ca0b460 ("net/hns3: support some device operations")
Fixes: a5475d61fa ("net/hns3: support VF")
Cc: stable@dpdk.org
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Acked-by: Lijun Ou <oulijun@huawei.com>
In current version, procedure of saving eth_dev in
hns3 PMD init will be called more than twice, one
for primary, the other for secondary. That will cause
segmentation fault in Multi-process as eth_dev will
be changed in secondary process, which is different
from one in primary process.
The initial problem was access to 'rte_eth_devices'
global variable, which is wrong. But current approach
can cause problem for the secondaries, moving 'eth_dev'
to process private can work but before making things
more complex.
This patch deserted the procedure of saving eth_dev in
hns3 PMD init. Instead, it creates an internal function
that gets "struct hns3_hw" as parameter and it can be
called internally without knowing 'eth_dev'and the
.dev_ops can be wrapper to this.
Fixes: 2390bf217f ("net/hns3: fix FEC state query")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Abnormal errors stats in Rx/Tx datapath are statistics
items in driver, and displayed in xstats. They should
be cleared by the rte_eth_xstats_reset api, instead of
the rte_eth_stats_reset.
Fixes: c4b7d6761d ("net/hns3: get Tx abnormal errors in xstats")
Fixes: 521ab3e933 ("net/hns3: add simple Rx path")
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The ethdev API has processed the failure to obtain
xstats statistics. Therefore, driver should return
an error code instead of 0 in 'hns3_dev_xstats_get'
API.
Fixes: 8839c5e202 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, validity check for ids and values in the
hns3_dev_xstats_get_by_id API is incorrect, which will
cause a problem. Namely, if the ID range of the xstats
stats item does not include the basic stats item, the
app can not obtain the corresponding xstats statistics
in hns3_dev_xstats_get_by_id.
Similarly, the hns3_dev_xstats_get_names_by_id interface
also has a problem.
Although the input parameter verification code cannot be
executed due to the implementation of the ethdev framework
interface, the driver needs to ensure the correctness of
the input parameters.
Fixes: 8839c5e202 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The rte_fdir_conf structure has deprecated and users need
to use the specified rule parameters of rte_flow structure
when configure a flow rule. As a result, it is incorrectly
used in the rte_flow API.
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Building with SVE extension enabled stopped with error:
error: ACLE function ‘svwhilelt_b64_s32’ requires ISA extension ‘sve’
18 | #define PG64_256BIT svwhilelt_b64(0, 4)
This is caused by unintentional cflags reset.
Fixed the issue by not touching cflags, and using flags defined by
compiler.
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Cc: stable@dpdk.org
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
As FEC is not supported below 10 Gbps,
CMD(HNS3_OPC_CONFIG_FEC_MODE) offered from
Firmware read will return fail in 10 Gbps device.
This patch will prevent read this CMD when below 10 Gbps,
as this is non-sense.
Fixes: 9bf2ea8dbc ("net/hns3: support FEC")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Here the printing of MAC addresses is adjusted. After the
modification, only some bytes of the MAC address are
displayed.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
For kupeng 930, there are 3 registers to control the enable
status of a TQP(i.e. task queue pair, include a txq and a rxq).
One of them controls whether the TQP is enabled, and the other
two controls whether the rxq and txq are enabled. The registers
used to control the enabled status of the rxq and txq are enabled
by default. Therefore, after the TQP is enabled, the rxq and txq
are enabled by default.
Currently, when the number of rxq is not equal to the number of txq, the
unused rxqs or txqs are not disabled by driver, so these unused queues
will be enabled in this situation. And the related HW rings have not
been initialized which could lead to a hardware exception.
This patch fix it by disable these unused queues during enable the TQPs.
Fixes: fa29fe45a7 ("net/hns3: support queue start and stop")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The HW and SW DCB configurations need to be updated only
after the DCB configuration information changed. But the
change of tx/rx queue number is ignored. If user decreases
the number of tx queue after configuring multi-TC, the queue
mapping information in hns3_tc_queue_info can not be updated.
And then accessing the released queue resource in
"hns3_init_tx_ring_tc" will trigger a segment fault.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Reasons for building not supported generally start with lowercase
because printed as the second part of a line.
Other changes:
- "linux" should be "Linux" with a capital letter.
- ARCH_X86_64 may be simply x86_64.
- aarch64 is preferred over arm64.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: David Marchand <david.marchand@redhat.com>
According to bit operator reliability style, variables in
the right expression participating int bit operation
must be an unsigned type.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
According to the rule of the static check tools
that arrange blank lines properly to keep the
code compact, here remove some unnecessary blank
line to fix the above rule warning.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
FLR operation will reset the queue enabling state and
the driver needs to restore the state after reset.
If the driver does not restore the state, it will result
in unpredictable behavior with reset when user start or
stop queue by calling the relevant function if.
This patch fix it by add a queue enabling state restore
function to the reset handler.
Fixes: fa29fe45a7 ("net/hns3: support queue start and stop")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Here adds a check for the return value when calling
rte_pci_write_config.
Coverity issue: 363714
Fixes: cea37e5133 ("net/hns3: fix FLR reset")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
According to the rule of the used static check tool,
each member is initialized on a separate lines when
struct and union members are initialized, here is
tempting to adjust some code lines in order to remove
the warning.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
In current driver print log function, some print format
symbols does not match with the actual variable types.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Some header files have included by others. Also,
some header files have a header file self-contained
error will trigger building warning. As a result,
it is unnecessary and move it into the correct
location.
Beside, here also remove some unused lines.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
If hardware does not support QL (quantity limiter), the int_ql_max
is 0, software should confirm ql_value is less than int_ql_max
before write QL register. This patch add check of int_ql_max
value from firmware and delete the unused variable coalesce_mode.
Fixes: 27911a6e62 ("net/hns3: add Rx interrupts compatibility")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Scheduling rate of port-level in hns3 PF driver configured to
hardware is obtained from firmware, which determines the
bandwidth capability of the port. The rate in firmware is
generally configured with the maximum value for network engine
supporting multiple rates, such as 10G and 25G. It may cause
the following issues:
1) When a 10G optical module is used on the network engine, scheduling
rate of this port will also be configured to hardware with 25G.
However, the MAC rate of this port is 10G. In this case, it is
unreasonable that the port scheduling rate is different from the MAC
rate.
2) If default speed in firmware is not the maximum value, the 25G port
may not reach the capability of the port.
Therefore, we fix configurations of port-level scheduling rate
according to updating of MAC link speed.
Fixes: 59fad0f321 ("net/hns3: support link update operation")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Kupeng920 support tso and checksum offload for VXLAN_GPE with
the next protocol id 3(i.e., Ethernet).
Kupeng930 support TSO and checksum offload for VXLAN_GPE with
the next protocol id 1,2,3(i.e., IPv4, IPv6 and Ethernet).
This patch add support for this tunnel type.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, the header length of all the layers are fixed, It would
lead to a csum error when the header length changed.
This patch fixes above problem by using the header length in mbuf
instead of the fixed header length to perform the TX cksum offload.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, there are two mistakes in Tx checksum outer header prepare.
1) Check whether the packet outer header is IPV4 based on PKT_TX_IPV4
which is incorrect.
2) For HIP08, the outer UDP cksum could not be offloaded. And driver
should ensure the outer udp cksum filed set to 0. In current code,
PKT_TX_UDP_CKSUM is used to determine whether the outer layer of
the packet is a UDP header. Actually, for tunnel TSO, the flag will
never be set.
For the first mistake, it is fixed by replacing PKT_TX_IPV4 with
PKT_TX_OUTER_IPV4. And the protocol number in L3 header is used to check
whether the outer L4 header is UDP.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Fixes: 6dca716c9e ("net/hns3: support TSO")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
For Kunpeng920, both tx and rx promisc is set when the promisc mode
is enabled. In other words, all the ingress packets and the packets sent
from the PF and other VFs on the same physical port will be copied
to the function which set promisc mode on.
Kunpeng930 support to turn off the tx unicast promisc. A limit promisc
mode is introduced, which means turn off the tx unicast promisc when
promisc is set.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The ARM SVE vector implementation defined macro is
__ARM_FEATURE_SVE and RTE_MACHINE_CPUFLAG macros
have replaced by regular compiler macros.
Besides, we remove the unused macro RTE_LIBRTE_HNS3_INC_VECTOR_SVE.
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently hns3vf_reinit_dev only judge whether the return value of
setting PCI bus function is not 0, while it will return a negative
value when execute failed.
Fixes: 243651cb6c ("net/hns3: check PCI config space reads")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, the rx HW ring is not cleared after queue stop.
When there are packets remaining in the HW rings and the
queues have been stopped, if upper layer user calls the
rx_burst function at this time, an illegal memory access
will occur due to the sw rings has been released.
This patch fix this by reset the sw ring after disable the
queue.
Fixes: fa29fe45a7 ("net/hns3: support queue start and stop")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, u8 type variable is used to control to release fake queues in
hns3_fake_rx/tx_queue_config function. Although there is no case in
which more than 256 fake queues are created in hns3 network engine, it
is unreasonable to compare u8 variable with u16 variable.
Fixes: a951c1ed3a ("net/hns3: support different numbers of Rx and Tx queues")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
There are coverity defects related "calling
hns3_reset_all_tqps without checking return value
in hns3_do_start".
This patch fixes the warning by add "void" declaration
because here is exception handling, hns3_reset_all_tqps
will have the corresponding error message if it is
handled incorrectly, so it is not necessary to check
hns3_reset_all_tqps return value, here keep ret as the
error code causing the exception.
Coverity issue: 363048
Fixes: fa29fe45a7 ("net/hns3: support queue start and stop")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, hns3 supports recognizing a lot of ptypes, but most
tunnel packet types are not reported to the API
rte_eth_dev_get_supported_ptypes.
And there are some errors in L2 and L3 packet recognition. The
ARP and LLDP are classified to L3 field in RX descriptor. So,
the ptype of LLDP and ARP packets will be set twice. And ptypes
are assigned by bitwise OR, which will eventually cause the ptype
result to be incorrect.
Besides, when a packet with only L2 header, its ptype will not
report by hns3 PMD. This is because the L2/L3 ptype table is not
initialized properly. In this case, the table query result is 0
by default.
As a result, it fixes missing supported ptypes and the mistake in
L2/L3 packet recognition and the unreported L2 packet ptype by
reporting its L2 type when the L3 type unrecognized..
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Currently, driver uses the maximum number of queues configured by user
as the maximum queue id that can be specified by the RSS rule or the
reta_update api. It is unreasonable and may trigger an incorrect
behavior in the multi-TC scenario. The driver must ensure that the queue
id configured in the redirection table must be within the range of the
number of queues allocated to a TC.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Implement the available and used rxd number count function.
In Kunpeng series, the NIC hardware supports to read the bd numbers
which wait processed from the hardware FBD (Full Buffer Descriptor),
and the driver maintains the bd number to be written back hardware.
Compare the number of FBDs with the number of BDs to be written back to
the hardware.
The number of used descriptors of a rx queue is computed as follows:
The fbd numbers of reading from FBD register plus the bd numbers to be
written back to hardware maintained by the driver.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
For Kunpeng930 NIC hardware, it supports to use dst/src port to
RSS hash for ipv6-sctp packet type. However, the Kunpeng920 NIC
hardware is different with it. The Kunpeng920 NIC only supports
dst/src ip to RSS hash for ipv6-sctp packet type.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The legacy filter API, including rte_eth_dev_filter_supported() and
rte_eth_dev_filter_ctrl() is removed. Flow API should be used.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since each version map file is contained in the subdirectory of the library
it refers to, there is no need to include the library name in the filename.
This makes things simpler in case of library renaming.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Queue stats are stored in 'struct rte_eth_stats' as array and array size
is defined by 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag.
As a result of technical board discussion, decided to remove the queue
statistics from 'struct rte_eth_stats' in the long term.
Instead PMDs should represent the queue statistics via xstats, this
gives more flexibility on the number of the queues supported.
Currently queue stats in the xstats are filled by ethdev layer, using
some basic stats, when queue stats removed from basic stats the
responsibility to fill the relevant xstats will be pushed to the PMDs.
During the switch period, temporary 'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS'
device flag is created. Initially all PMDs using xstats set this flag.
The PMDs implemented queue stats in the xstats should clear the flag.
When all PMDs switch to the xstats for the queue stats, queue stats
related fields from 'struct rte_eth_stats' will be removed, as well as
'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS' flag.
Later 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag also can be
removed.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Change eth_dev_stop_t return value from void to int.
Make eth_dev_stop_t implementations across all drivers to return
negative errno values if case of error conditions.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The function rte_eth_dev_release_port() is partially resetting
the struct rte_eth_dev. The drivers were completing this reset
with more pointers set to NULL in the close or remove operations.
More pointers are reset at ethdev level,
and some redundant assignments are removed from PMDs.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
When closing a port, it is supposed to be already stopped,
and marked as such with "dev_started" state zeroed by the stop API.
Resetting "dev_started" before calling the driver close operation
was hiding the case of not properly stopped port being closed.
The flag "dev_started" is not changed anymore in "rte_eth_dev_close()".
In case the "dev_stop" function is called from "dev_close",
bypassing "rte_eth_dev_stop()" API,
the "dev_started" state must be explicitly reset in the PMD
in order to keep the same behaviour.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
This patch adds SVE vector instructions to optimize Tx burst process.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Forward error correction (FEC) is a bit error correction mode.
It adds error correction information to data packets at the
transmit end, and uses the error correction information to correct
the bit errors generated during data packet transmission at the
receive end. This improves signal quality but also brings a delay
to signals. This function can be enabled or disabled as required.
This patch adds FEC support for ethdev.Introduce ethdev
operations which support query and config FEC information in
hardware.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Reviewed-by: Chengwen Feng <fengchengwen@huawei.com>
Reviewed-by: Chengchang Tang <tangchengchang@huawei.com>
When an error occurs in the reset process, -EIO is returned.
The assignment of ret here is redundant, so deleted it.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The new generation hns3 network engine supports independent enabling and
disabling of a single Tx/Rx queue. So, it can support the queue start
and stop feature. In addition, when different numbers of Tx and Rx
queues need to be enabled in some applications, hns3 pmd does not need
to create fake queues to enable these scenarios.
This patch Add queue start and stop feature for the new generation hns3
networking engine. Cancel the creation of fake queue on the new
generation network engine. And the previously improperly named queue
related function was renamed to improve readability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, max scheduling rates configuration of pg, pri and port are
set to 100000Mbps, which is the maximum bandwidth of hns3 network engine
with revision_id equals 0x21. However, max scheduling rate configuration
should be set to hardware based on the actual hardware board
environment.
The max_tm_rate in struct hns3_hw, meaning the rate, is obtained from
firmware. So we should use the variable to configure the max scheduling
rate.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
In order to have more flexible selection of shapping algorithm based on
different versions of hns3 network engine, moves the algorithm of
calculating shapping parameter to firmware to execute. If bit
HNS3_TM_RATE_VLD_B of flag field of struct named hns3_pri_shapping_cmd,
hns3_pg_shapping_cmd or hns3_port_shapping_cmd is set to 1, firmware of
network engine, which device revision_id is greater than and equal to
0x30, will recalculate the shapping parameters according to the xxx_rate
field of struct hns3_xxx_shapping_cmd and the opcode of scheduling
level, and configure to hardware.
But driver still needs to calculate shapping parameters and configure
firmware, so as to be compatible with the network engine with
revision_id eqauls 0x21. And the rate and the flag will be ignored based
on the network engine with revision_id equals 0x21.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The API of rte_flow_error_set is used to pass detail error information
to caller, this patch sets suitable type when calling rte_flow_error_set
API.
Fixes: fcba820d9b ("net/hns3: support flow director")
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Because the macro named RTE_FLOW_ERROR_TYPE_ACTION_CONF indicates a
action configuration and the macro named RTE_FLOW_ERROR_TYPE_ACTION
indicates a specific action, the driver needs to return
RTE_FLOW_ERROR_ACTION_CONF type and notify the user when a RSS
configuration is invalid with actions list in the internal function
named hns3_parse_rss_filter called by the '.validate' ops implementation
function named hns3_flow_validate.
Besides, this patch removes some unnecessary judgment lines in
hns3_parse_rss_filter.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The maximum number of queues for hns3 PF and VF driver is 64 based on
hns3 network engine with revision_id equals 0x21. Based on hns3 network
engine with revision_id equals 0x30, the hns3 PF PMD driver can support
up to 1280 queues, and hns3 VF PMD driver can support up to 128 queues.
The following points need to be modified to support maximizing queue
number and maintain better compatibility:
1) Maximizing the number of queues for hns3 PF and VF PMD driver In
current version, VF is not supported when PF is driven by hns3 PMD
driver. If maximum queue numbers allocated to PF PMD driver is less
than total tqps_num allocated to this port, all remaining number of
queues are mapped to VF function, which is unreasonable. So we fix
that all remaining number of queues are mapped to PF function.
Using RTE_LIBRTE_HNS3_MAX_TQP_NUM_PER_PF which comes from
configuration file to limit the queue number allocated to PF device
based on hns3 network engine with revision_id greater than 0x30. And
PF device still keep the maximum 64 queues based on hns3 network
engine with revision_id equals 0x21.
Remove restriction of the macro HNS3_MAX_TQP_NUM_PER_FUNC on the
maximum number of queues in hns3 VF PMD driver and use the value
allocated by hns3 PF kernel netdev driver.
2) According to the queue number allocated to PF device, a variable
array for Rx and Tx queue is dynamically allocated to record the
statistics of Rx and Tx queues during the .dev_init ops
implementation function.
3) Add an extended field in hns3_pf_res_cmd to support the case that
numbers of queue are greater than 1024.
4) Use new base address of Rx or Tx queue if QUEUE_ID of Rx or Tx queue
is greater than 1024.
5) Remove queue id mask and use all bits of actual queue_id as the
queue_id to configure hardware.
6) Currently, 0~9 bits of qset_id in hns3_nq_to_qs_link_cmd used to
record actual qset id and 10 bit as VLD bit are configured to
hardware. So we also need to use 11~15 bits when actual qset_id is
greater than 1024.
7) The number of queue sets based on different network engine are
different. We use it to calculate group number and configure to
hardware in the backpressure configuration.
8) Adding check operations for number of Rx and Tx queue user configured
when mapping queue to tc Rx queue numbers under a single TC must be
less than rss_size_max supported by a single TC. Rx and Tx queue
numbers are allocated to every TC by average. So Rx and Tx queue
numbers must be an integer multiple of 2, or redundant queues are not
available.
9) We can specify which packets enter the queue with a specific queue
number, when creating flow table rules by rte_flow API. Currently,
driver uses 0~9 bits to record the queue_id. So it is necessary to
extend one bit field to record queue_id and configure to hardware, if
the queue_id is greater than 1024.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The maximum number of queues for one TC hns3 PF PMD driver supported is
64 based on hns3 network engine with revision_id equals 0x21, while it
is expanded up to 512 on hns3 network engine with revision_id equals
0x30.
So the following points need to be modified to maintain better
compatibility.
1) Using a extended rss_size_max field as the maximum queue number of
one TC PF driver supported.
2) The data type of the RSS redirection table needs to be changed from
uint8_t to uint16_t.
3) rss_tc_mode modification
The bitwidth of tc_offset, meaning the rx queue index, has to expand
from 10 bit to 11 bits. The tc_size, meaning the exponent with base 2
of queues supported on TC, needs to expand from 3 bits to 4 bits.
4) RSS indirection table modification
Currently, a field with 7 bits width is used to record the queue
index for RSS indirection table. It means that PF needs to expand the
queue index field to 9 bits. As the RSS indirection table config
command reserved 4 bytes to configure the RSS queue index, a extern
field can be added. So an entries of RSS indirection table queue
index has two fields to set: rss_result_l and rss_result_h, while
rss_result_l records the lower 8 bits and rss_result_h records the
higher 1 bit.
In addition, 2~4 modifications is also compatible with hns3 VF PMD
driver.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The temporary flag RTE_ETH_DEV_CLOSE_REMOVE is removed.
It was introduced in DPDK 18.11 in order to give time for PMDs to migrate.
The old behaviour was to free only queues when closing a port.
The new behaviour is calling rte_eth_dev_release_port() which does
three more tasks:
- trigger event callback
- reset state and few pointers
- free all generic port resources
The private port resources must be released in the .dev_close callback.
The .remove callback should:
- call .dev_close callback
- call rte_eth_dev_release_port()
- free multi-port device shared resources
Despite waiting two years, some drivers have not migrated,
so they may hit issues with the incompatible new behaviour.
After sending emails, adding logs, and announcing the deprecation,
the only last solution is to declare these drivers as unmaintained:
ionic, liquidio, nfp
Below is a summary of what to implement in those drivers.
* The freeing of private port resources must be moved
from the ".remove(device)" function to the ".dev_close(port)" function.
* If a generic resource (.mac_addrs or .hash_mac_addrs) cannot be freed,
it must be set to NULL in ".dev_close" function to protect from
subsequent rte_eth_dev_release_port() freeing.
* Note 1:
The generic resources are freed in rte_eth_dev_release_port(),
after ".dev_close" is called in rte_eth_dev_close(), but not when
calling ".dev_close" directly from the ".remove" PMD function.
That's why rte_eth_dev_release_port() must still be called explicitly
from ".remove(device)" after calling the ".dev_close" PMD function.
* Note 2:
If a device can have multiple ports, the common resources must be freed
only in the ".remove(device)" function.
* Note 3:
The port is supposed to be in a stopped state when it is closed.
If it is not the case, it is free to the PMD implementation
how to react when trying to close a non-stopped port:
either try to stop it automatically or just return an error.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
The device operation .dev_close was returning void.
This driver interface is changed to return an int.
Note that the API rte_eth_dev_close() is still returning void,
although a deprecation notice is pending to change it as well.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Reviewed-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Currently, when calling the rte_flow_query API function to query the RSS
information, the queue related information is not as expected.
The root cause is that when application call the rte_flow_create API
function to create RSS action, the operation of storing the data whose typs
is struct rte_flow_action_rss is incorrect in the '.create' ops
implementation function named hns3_flow_create.
This patch fixes it by replacing memcpy with hns3_rss_conf_copy function to
store the RSS information in the hns3_flow_create.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, when running the following commands in the CLI of testpmd
application, the driver reports an -EINVAL error when performing the No.3
step.
1) flow create 0 ingress pattern end actions rss key <key> func simple_xor
types all end / end
2) flow flush 0
3) port config dcb vt off pfc off
The root cause as below:
In the No.2 step, when RSS rules is flushed, we set the the flag
hw->rss_dis_flag with true to indicate RSS id disabled. And in the No.3
step, calling rte_eth_dev_configure API function, the internal function
named hns3_dev_rss_hash_update check hw->rss_dis_flag is true and return
-EINVAL.
When user calls the rte_eth_dev_configure API function with the input
parameter dev_conf->rxmode.mq_mode having ETH_MQ_RX_RSS_FLAG to enable RSS,
driver should set internal flag hw->rss_dis_flag with false to indicate RSS
is enabled in the '.dev_configure' ops implementation function named
hns3_dev_configure and hns3vf_dev_configure.
Fixes: 5e782bc257 ("net/hns3: fix configuring RSS hash when rules are flushed")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When user create a flow without RSS by calling rte_flow_create API and then
destroy it by calling rte_flow_flush API, driver should not clear RSS rule.
A reasonable handling method is that when user creates an RSS rule, the
driver should clear the created RSS rule when flushing destroy all flow
rules. Also, hw->rss_info should save the RSS config of the last success
RSS rule. When create n RSS rules, the RSS should not be disabled before
the last RSS rule destroyed.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When user specifies RSS queue num for 0 in action list by flow create API,
it should create a valid flow rule. The following flow rule should be
success in the command line of the testpmd application:
flow create 0 <pattern> actions rss queues / end
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currnetly, when user create a flow RSS rule and then flush the rule, driver
will set 0 for the internal structure of hw->rss_info maintained in driver.
And then user create a flow RSS rule without specified RSS hash key, driver
configure a validate RSS hash key into hardware network engine and will
cause an RSS error. The related steps when using testpmd as
follows:
flow 0 <pattern> action rss xx end / end
flow flush 0
flow 0 <pattern> action rss queues 0 1 end / end
To slove the preceding problem, the flow flush processing is modified.
it don't clear all RSS configurations for hw->rss_info. Actually the RSS
key information in the hardware is not cleared, therefore, the
hw->rss_info.key is kept consistent with the value in the hardware. In
addition, because reset the redirection table, we need to set queues NULL
and queue_num for zero that indicate the corresponding parameters in the
hardware is unavailable. Also we set hw->rss_info.func to
RTE_ETH_HASH_FUNCTION_MAX that indicate it is invalid.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch support for hash type input set configuration. That is, upper
level application can call the rte_flow_create or
rte_eth_dev_rss_hash_update API to set the specified tuples by RSS types.
As a result, the hardware can selectively use the tuples to perform hash
calculation based on the specific tuple to enable the fields.
The following uses the RSS flow as an example:
When application calls the rte_flow_create API to select tuple input for
ipv4-tcp l3-src-only, the driver can enable the ipv4-tcp src field of the
hardware register by calling the internal function named
hns3_set_rss_tuple_by_rss_hf according to the RSS types in actions list.
In testpmd application, the command as follows:
testpmd> flow create 0 ingress pattern end actions rss types \
ipv4-tcp l3-src-only end queues 1 3 end / end
The following use the rte_eth_dev_rss_hash_update as an example:
if the user set the select tuple input for ipv4-tcp l3-src-only by
rte_eth_rss_conf structure in rte_eth_dev_rss_hash_update. the next
flow is the same as that of the RSS flow. In testpmd application,
the command as follows:
testpmd> port config all rss ipv4-tcp l3-src-only
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds checking the input RSS type when creating a flow with RSS.
If the input RSS type are not supported based on hns3 network engine, an
error is returned.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch enables to query some RSS configurations of the specified
rule. For example, show RSS hash function and rss types.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Kunpeng 930 hardware support spread packets to region of queues which can
be configured by FDIR rule, it means user can create one FDIR rule which
action is one region of queues, and then RSS use the region info to spread
packets.
As we know, RTE_FLOW_ACTION_TYPE_RSS is used to spread packets among
several queues, user could config such as func/level/types/key/queue
parameter to control RSS function, so we provide this feature under the
RTE_FLOW_ACTION_TYPE_RSS framework.
Consider RSS input tuple don't have eth header, we use the following
rule to distinguish them (whether it's queue region configuration or
rss general configuration):
Case 1: pattern have ETH and action's queue_num > 0, indicate it is
queue region configuration.
Case other: rss general configuration.
So if user want to configure one flow which ipv4=192.168.1.192 spread to
queue region of queue 0/1/2/3, the patter should:
RTE_FLOW_ITEM_TYPE_ETH with spec=last=mask=NULL
RTE_FLOW_ITEM_TYPE_IPV4 with spec=192.168.1.192 last=mask=NULL
RTE_FLOW_ITEM_TYPE_END
the action should:
RTE_FLOW_ACTION_TYPE_RSS with queue_num=4 queue=0/1/2/3
RTE_FLOW_ACTION_TYPE_END
after calling rte_flow_create, one FDIR rule will be created.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch solves the redundant operation during traversal. In the internal
function named hns3_error_int_stats_add for adding error statistics,
because only one statistical item will be found in the for loop statement,
a break can be executed after finding the error statistical item without
traversing the remaining table entries.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch solves the static check warning in the internal function named
hns3_fd_convert_tuple as follow:
"The switch statement must have a 'default' branch".
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
According to the protocol of PCIe, FLR to a PF device resets the PF state
as well as the SR-IOV extended capability including VF Enable which means
that VFs no longer exist.
When PF device is in FLR reset stage, at this time, the register state
of VF device is not reliable, so VF device's register state detection
is not carried out in PF FLR.
In this case, we just ignore the register states to avoid accessing
nonexistent register and return false in the internal function named
hns3vf_is_reset_pending to indicate that there are no other reset states
that need to be processed by PMD driver.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
In kunpeng 920, when process pkts which need TSO, the network driver
need to erase the L4 len value of the TCP TSO pseudo header and
recalculate the pseudo header checksum. kunpeng930 support not need
to erase the L4 len value of the TCP TSO pseudo header.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Kunpeng 920 supports the maximum nb_segs of non-tso packet is 8 in Tx
direction, kunpeng 930 expands this limit value to 18, this patch sets
the corresponding value by querying the maximum number of non-tso nb_segs
supported by the device during initialization.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
This patch solves the static check warning as follow:
"The switch statement must have a 'default' branch".
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, the default VLAN (vlan id 0) will never be deleted from the
hardware VLAN table based on hns3 PF device. As a result, even a
non-zero PVID is set by calling rte_eth_dev_set_vlan_pvid based on hns3
PF device, packets with VLAN 0 and without VLAN are still received by PF
driver in Rx direction.
This patch deletes the restriction that VLAN 0 cannot be removed in PVID
configuration to ensure packets without PVID will be filtered when PVID
is set. And the patch adds VLAN 0 to the soft list when initializing
vlan configuration to ensure that VLAN 0 will be deleted from the
hardware VLAN table when device is closed.
Fixes: 411d23b9ea ("net/hns3: support VLAN")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Because of hardware limitation based on the old version of hns3 network
engine, there are some restrictions:
a) HNS3 PMD driver needs select different processing mode for VLAN based
on whether PVID is set which means our driver need sense the PVID
states.
b) For packets transmitting process, only two layer of VLAN tag is
supported. If the total number of VLAN tags in mbuf and VLAN offload
by hardware (VLAN insert by descriptor) exceeds two, the VLAN in mbuf
will be overwritten by VLAN in the descriptor.
c) If port based VLAN is set, only one VLAN header is allowed in mbuf or
it will be discard by hardware.
In order to solve these restriction, two change is implemented on the
new versions of network engine.
1) add a new VLAN tagged insertion mode, named tag shift mode;
2) add a new VLAN strip control bit, named strip hide enable;
The tag shift mode means that VLAN tag will shift automatically when the
inserted place has a tag. For PMD driver, the VLAN tag1 and tag2
configurations in Tx side do not need to be considered because the
hardware completes it. However, the related configuration will still be
retained to be compatible with the old version of network engine.
The VLAN strip hide means that hardware will strip the VLAN tag and hide
VLAN in descriptor (VLAN ID exposed as zero and related STRIP_TAGP is
off).
These changes make it no longer necessary for the hns3 PMD driver to be
aware of the PVID status and have the ability to send mult-layer (more
than two) VLANs packets. Therefore, hns3 PMD driver introduces the
concept of VLAN mode and adds a new VLAN mode named HNS3_PVID_MODE to
indicate that PVID-related IO process can be implemented by the
hardware. And VF driver does not need to be modified because the related
mailbox messages will not be sent by PF kernel mode netdev driver under
new network engine and all the related hardware configuration is on the
PF side.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, there is a possibility that segment faults occur when sending
packets whose payloads are stored in multiple buffers based on hns3
network engine. The related core dump information as follows:
Program terminated with signal 11, Segmentation fault.
0 hns3_reassemble_tx_pkts
2512 temp = temp->next;
Missing separate debuginfos, use:
(gdb) bt
0 hns3_reassemble_tx_pkts
1 0x0000000000969c60 in hns3_check_non_tso_pkt
2 0x000000000096adbc in hns3_xmit_pkts
3 0x000000000050d4d0 in rte_eth_tx_burst
4 0x000000000050fca4 in pkt_burst_transmit
5 0x00000000004ca6b8 in run_pkt_fwd_on_lcore
6 0x00000000004ca7fc in start_pkt_forward_on_core
7 0x00000000006975a4 in eal_thread_loop
8 0x0000ffffa6f7fc48 in start_thread
9 0x0000ffffa6ed1600 in thread_start
The root cause is that hns3 PMD driver invokes the rte_pktmbuf_free_seg
API function to release the same rte_mbuf multiple times. The rte_mbuf
pointer is not set to NULL in the internal function
hns3_rx_queue_release_mbufs which is invoked during queue setup, stop
and close. As a result the rte_mbuf in Rx queues will be repeatedly
released when the user application setup queues or stop/start the dev
for multiple times.
Probably for performance reasons, DPDK mempool lib does not check for
the repeated rte_mbuf releases. The Address of released rte_mbuf are
directly stored into the per lcore cache of the mempool. This makes the
rte_mbufs obtained from mempool by calling rte_mempool_get_bulk API
function repetitively. ultimately, it causes to access to a NULL
pointer in PMD driver.
This patch fixes this problem by setting released mbuf pointer to NULL
in the internal function named hns3_rx_queue_release_mbuf. And the other
internal function named hns3_reassemble_tx_pkts is optimized to avoid a
similar problem.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
When Rx of scattered packets is off, we have some possibility of using
vector Rx process function or simple Rx functions in hns3 PMD driver.
If the input MTU is increased and the maximum length of received packets
is greater than the length of a buffer for Rx packets, the hardware
network engine needs to use multiple BDs and buffers to store these
packets. This will cause problems when still using vector Rx process
function or simple Rx function to receiving packets. So, when Rx of
scattered packets is off and device is started, it is not permitted to
increase MTU so that the maximum length of Rx packets is greater than Rx
buffer length.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds simple Tx process function. When multiple segment
packets are not needed, Which means that DEV_TX_OFFLOAD_MBUF_FAST_FREE
offload is not set, we can simple Tx process.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
This patch adds simple Rx process function and support chose Rx function
by real Rx offloads capability.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
This patch adds the internal function named hns3_write_reg_opt to avoid
performance loss from address calculation during register access in the
'.rx_pkt_burst' ops implementation function named hns3_recv_pkts.
In addition, because hardware always access register in little-endian
mode based on hns3 network engine, so driver should also call
rte_cpu_to_le_32 to convert data in little-endian mode before writing
register and call rte_le_to_cpu_32 to convert data after reading from
register. Here the driver encapsulates the data conversion operation in
the register read/write operation function as below:
hns3_write_reg
hns3_write_reg_opt
hns3_read_reg
Therefore, when calling these functions, conversion is not required
again.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch reports .rx_free_thresh value in the .dev_infos_get ops
implementation function named hns3_dev_infos_get and
hns3vf_dev_infos_get.
In addition, the name of the member variable of struct hns3_rx_queue is
modified and comments are added to improve code readability.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, offload capabilities are only enabled for all Rx/Tx queues in
hns3 PF/VF PMD driver, and offload capability only applied in a Rx/Tx
queue is not supported.
So this patch moves 'DEV_TX_OFFLOAD_MBUF_FAST_FREE' from
tx_queue_offload_capa to tx_offload_capa.
Fixes: 1f5ca0b460 ("net/hns3: support some device operations")
Fixes: a5475d61fa ("net/hns3: support VF")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch fixes (out-of-bounds access) coverity issue.
Coverity issue: 349932
Fixes: 7d7f9f80bb ("net/hns3: support MAC address related operations")
Cc: stable@dpdk.org
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Reviewed-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The descriptor of the command between firmware and driver consists of
8-byte header and 24-byte data field. The contents sent to firmware are
packaged into a command structure as the data field of command
descriptor.
There are some command structures in hns3_dcb.h file that are less than
24 byte. So this patch fixes these incomplete command structures.
Fixes: 62e3ccc2b9 ("net/hns3: support flow control")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, default MAC address obtained from firmware in PF driver is
directly used by .mac_addr_set ops implementation function when the
rte_eth_dev_start API function is executed. At this moment, if the
default MAC addr isn't an unicast address, it will fail to set default
MAC addr to hardware.
So this patch adds the validity check of default MAC addr in PF driver.
We will use a random unicast address, if the default MAC address
obtained from firmware is not a valid unicast address.
In addition, this patch also adjusts the location of processing default
MAC addr in VF driver so as to increase relevance and readability of the
code.
Fixes: eab2177671 ("net/hns3: support setting VF MAC address by PF driver")
Fixes: d51867db65 ("net/hns3: add initialization")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
This patch uses RTE_MAX function in DPDK lib to replace the private
macro named max_t in driver.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The FDIR counter was used to count the number of FDIR hit, the maximum
number of the counter is 128 based on kunpeng 920, and it was 256 based
on kunpeng 930.
The firmware is responsible to allocate counters for different PF
devices, so the available counter number of one PF may be bigger than
128.
Currently, there are two places using the counter in driver:
1. Configure the counter. Driver uses the command whose opcode is
HNS3_OPC_FD_AD_OP, now we extend one bit to hold the high bit of
counter-id in the command format.
2. Query the statistic information of the counter. Driver uses the
command whose opcode is HNS3_OPC_FD_COUNTER_OP, now the command
already support 16-bit counter-id.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The new firmware adds the hardware error types reported by MSI-x mode.
These errors are defined as RAS errors in hardware and belong to a
different type from the MSI-x errors processed by the driver.
When hardware detects an error which must be handled by the driver for
device to run properly it reports the error information through the
MSI-x interrupt. After receiving the interrupt reported by the hardware,
the driver queries the error information and identifies the error level,
then rectifies the error. All errors will be logged.
In addition, the hardware may be reset at the function or global level
based on the error level. After the reset is complete, the hardware will
recover to the normal status.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
There are difference about padding ultra-short frame in Tx procession
for different versions of hardware network engine.
If packet length is less than minimum packet length supported by
hardware in Tx direction, driver need to pad it to avoid error. The
minimum packet length in Tx direction is 33 based on kunpeng 920, and 9
based on kunpeng 930.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
There are difference about queue's interrupt configurations for
different versions of hardware network engine, such as queue's interrupt
mapping mode, coalesce configuration, etc.
The following uses the configuration differences of the interrupt
mapping mode as an example.
1) For some versions of hardware network engine, such as kunpeng 920,
because of the hardware constraint, we need implement unmmapping
relationship configurations by binding all queues to the last
interrupt vector and reserving the last interrupt vector. This
results in a decrease of the maximum queues when upper applications
call the rte_eth_dev_configure API function to enable Rx interrupt.
2) And for another versions, such as kunpeng 930, hns3 PMD driver can
map/unmmap all interrupt vectors with queues when Rx interrupt is
enabled.
This patch resolves configuration differences about Rx interrupts based
on kunpeng 920 and kunpeng 930.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds getting device capabilities from firmware, so driver can
supply different capabilities and specifications to upper level
applications base on different versions of hardware network engine.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support for querying Rx/Tx queue information.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, if there are not available Rx buffer descriptors in receiving
direction based on hns3 network engine, incoming packets will always be
dropped by hardware. This patch reports the '.rx_drop_en' information to
DPDK framework in the '.dev_infos_get', '.rxq_info_get' and
'.rx_queue_setup' ops implementation function.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The rte_kernel_driver enum actually only pointed at PCI drivers and is
only used in the PCI subsystem.
Remove it from the generic device API and use a private enum in the PCI
code.
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
A decision was made [1] to no longer support Make in DPDK, this patch
removes all Makefiles that do not make use of pkg-config, along with
the mk directory previously used by make.
[1] https://mails.dpdk.org/archives/dev/2020-April/162839.html
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Start a new release cycle with empty release notes.
The ABI version becomes 21.0.
The ABI major is back to normal, having only one number (21 vs 20.0).
The map files are updated to the new ABI major number (21).
The ABI exceptions are dropped.
Travis ABI check is disabled because compatibility is not preserved.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
According to the definition of RSS types of action attributes from
testpmd, the driver will not disable RSS but instead requests the
unspecified "best-effort" settings when upper application call
rte_flow_create API function to create flow using empty RSS types.
As a result, here use the default RSS types when RSS types is empty.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
CRC is the end of frame, which occupies 4 bytes. Keeping CRC is a
feature of MAC, which will not strip CRC field when receiving frames.
The feature can be enabled using DEV_RX_OFFLOAD_KEEP_CRC offload by
upper level application. And the feature is only supported for hns3 PF
PMD driver, not supported for hns3 VF PMD driver
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The 200G device has a new device id 0xA228, so adds this device id
to pci table for pci driver can probe it. Similar to the network port
with other speed, the hns3 PMD driver gets 200G speed information
from firmware, and passes them to DPDK framework.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
The hns3 network engine is built-in multiple SoCs, such as kunpeng 920,
kunpeng 930, etc. The PCI revision id is 0x21 in kunpeng 920, and the
PCI revision id is 0x30 in kunpeng 930.
Copper media type is supported for hns3 PF device in kunpeng 930 and
later SoCs. The configuration operation for PHY is implemented by
firmware.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Based on hns3 network engine, in order to configure hardware VLAN insert
offload in Tx direction, PMD driver reads the VLAN tags from the
vlan_tci_outer and vlan_tci of the structure rte_mbuf, fills them into
the Tx Buffer Descriptor and sets the related offload flag for every
packet.
Currently, there are two VLAN related problems in the 'tx_pkt_burst' ops
implementation function:
1) When setting the related offload flag, PMD driver inserts the VLAN
tag into the position that close to L3 header. So, when upper
application sends a packet with a VLAN tag in the data buffer, the
VLAN offloaded by hardware will be added to the wrong position. It is
supposed to add the VLAN tag from the rte_mbuf to the position close
to the MAC header in the packet when using VLAN insertion.
And when PF PVID is enabled by calling the API function named
rte_eth_dev_set_vlan_pvid or VF PVID is enabled by hns3 PF kernel
ether driver, the VLAN tag from the structure rte_mbuf to enable the
VLAN insertion should be filled into the position that close to L3
header to avoid to be overwritten by the PVID which will always be
inserted in the position that close to the MAC address.
2) When sending multiple segment packets, VLAN information is required
to be filled into the first Tx Buffer descriptor. However, currently
hns3 PMD driver incorrectly placed it in the last Tx Buffer
Descriptor. This results in VLAN insert offload failure when sending
multiple segment packets.
This patch fixed them by filling the VLAN information into the position
of the Tx Buffer Descriptor.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch fixes up paylen calculation twice when processing TSO request
in the '.tx_pkt_burst' ops implementation function to avoid performance
loss.
Fixes: 6dca716c9e ("net/hns3: support TSO")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Currently, there is a coverity defect warning about hns3 PMD driver, the
detail information as blow:
CID 289969 (#1 of 1): Unchecked return value (CHECKED_RETURN)
1. check_return: Calling rte_mp_action_register without checking return
value (as is done elsewhere 11 out of 13 times).
The problem is that missing checking the return value of calling the API
rte_mp_action_register during initialization. If registering an action
function for primary and secondary communication failed, the secondary
process can't work properly.
This patch fixes it by adding check return value of the API function
named rte_mp_action_register in the '.dev_init' implementation function
of hns3 PMD driver.
Coverity issue: 289969
Fixes: 23d4b61fee ("net/hns3: support multiple process")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Because of the hardware constraints, hns3 network engine doesn't support
sending packets with more than eight fragments. And hns3 pmd driver
tries to reassemble these kind of packets to meet hardware requirements.
Currently, there are two problems:
1) when the input buffer_len * 8 < pkt_len, the packets are impossible
to be reassembled into 8 Buffer Descriptors. In this case, the
packets will be passed to hardware, which eventually causes a
hardware reset.
2) The meta data in origin packets which are required to fill into the
descriptor haven't been copied into the reassembled pkts.
This patch adds a check for 1) to ensure such packets will be dropped by
driver and copies useful meta data from the origin packets to the
reassembled packets.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Currently, rx_buf_size of hns3 PMD driver is fixed on, and it's value
depends on the firmware which will decrease the flexibility of PMD.
The receive side mbufs was allocated from the mempool given by upper
application calling rte_eth_rx_queue_setup API function. So the memory
chunk used for net device DMA is depend on the data room size of the
objects in this mempool. Hns3 PMD driver should set the rx_buf_len
smaller than the data room size of mempool and our hardware only support
the following four specifications: 512, 1024, 2148 and 4096.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
According to the user manual of Kunpeng920 SoC, the max allowed number
of segments per whole packet is 63 and the max number of segments per
packet is 8 in datapath.
This patch reports the Two segment parameters of Tx descriptor
limitations to DPDK framework.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When the last driver exits abnormally, for example, it is killed by
'kill -9', it may be too late to clear the configuration and cause the
configuration to remain. Therefore, to ensure that the hardware
environment is clean during initialization, the PF driver actively clear
the hardware environment during initialization, including PF and
corresponding VFs' vlan, mac, flow table configurations, etc.
Fixes: d51867db65 ("net/hns3: add initialization")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
This patch optimizes the code to get device capability in primary
process, and moves the code of getting PCI revision id in order to avoid
evaluating the private hw->revision of shared PMD-specific private data
in slave process.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
This patch adds support setting VF PVID by hns3 PF kernel ethdev driver
on the host by "ip link set <eth num> vf <vf id> vlan <vlan tag>"
command.
Because of the hardware constraints, the striped VLAN tag will always in
Rx descriptors which should has been dropped when PVID is enabled and
the PVID will overwrite the outer VLAN tag in Tx descriptor. So, hns3
PMD driver need to change the processing of VLAN tags in the process of
Tx and Rx according to whether PVID is enabled.
1) If the hns3 PF kernel ethdev driver sets the PVID for VF device
before the initialization of the related VF device, hns3 VF PMD
driver should get the PVID state from PF driver through mailbox and
update the related state in txq and rxq maintained by hns3 VF driver
to change the process of Tx and Rx.
2) If the hns3 PF kernel ethdev driver sets the PVID for VF device after
initialization of the related VF device, the PF driver will notify VF
driver to update the PVID state. The VF driver will update the PVID
configuration state immediately to ensure that the VLAN process in Tx
and Rx is correct. But in the window period of this state transition,
packets loss or packets with wrong VLAN may occur.
3) Due to hardware limitations, we only support two-layer VLAN hardware
offload in Tx direction based on hns3 network engine, so when PVID is
enabled, QinQ insert is no longer supported. And when PVID is
enabled, in the following two cases:
i) packets with more than two VLAN tags.
ii) packets with one VLAN tag while the hardware VLAN insert is
enabled.
The packets will be regarded as abnormal packets and discarded by
hardware in Tx direction. For debugging purposes, a validation check
for these types of packets is added to the '.tx_pkt_prepare' ops
implementation function named hns3_prep_pkts to inform users that
these packets will be discarded.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Currently, hns3 PMD driver needs know the PVID configuration state and
do different processing in the 'rx_pkt_burst' ops implementation
function.
This patch adds a member to struct hns3_rx_queue/hns3_tx_queue of the
driver to indicate the PVID configuration status, so it isn't need
to access other data structure in the 'rx_pkt_burst' ops implementation,
to avoid performance loss because of reducing cache miss.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support of LRO offload for hns3 PMD driver.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support of symmetric algorithm of RSS.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Introduce the RTE_LOG_REGISTER macro to avoid the code duplication
in the logtype registration process.
It is a wrapper macro for declaring the logtype, registering it and
setting its level in the constructor context.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Acked-by: Sachin Saxena <sachin.saxena@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
There are coverity defects related "Unintended sign extension" in the
internal static function named hns3_get_regs_length used for dumping reg
operation.
This patch fixes them by replacing the data type of cmdq_lines,
common_lines, ring_lines and tqp_intr_lines with uint32_t in the inner
static function named hns3_get_regs_length of hns3 PMD driver.
Coverity issue: 349917, 349914
Fixes: 936eda25e8 ("net/hns3: support dump register")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, there are coverity defects warning as below:
CID 349937 (#1 of 1): Unintended sign extension (SIGN_EXTENSION)
sign_extension: Suspicious implicit sign extension: port_number with
type uint16_t (16 bits, unsigned) is promoted in port_number << cur_pos
to type int (32 bits, signed), then sign-extended to type unsigned long
(64 bits, unsigned). If port_number << cur_pos is greater than
0x7FFFFFFF, the upper bits of the result will all be 1.
CID 349893 (#1 of 1): Unintended sign extension (SIGN_EXTENSION)
sign_extension: Suspicious implicit sign extension: vlan_tag with type
uint8_t (8 bits, unsigned) is promoted in vlan_tag << cur_pos to type
int (32 bits, signed), then sign-extended to type unsigned long (64
bits, unsigned). If vlan_tag << cur_pos is greater than 0x7FFFFFFF, the
upper bits of the result will all be 1.
This patch fixes them by replacing the data type of port_number and
vlan_tag with uint32_t in the inner static function named
hns3_fd_convert_meta_data of hns3 PMD driver.
Coverity issue: 349937, 349893
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
There is a coverity defect related "Unchecked return value".
The internal static hns3_reset_err_handle function is reset error
process of hns3 PMD driver. If failure in reset process, it does not
mean that the network port is completely unavailable, so the command
interface between driver and firmware still needs to be initialized.
Regardless of whether the execution of the function named hns3_cmd_init
is successful or not, the next process after execution must be
continued, so there is no need to check the return value. If
hns3_cmd_init fails to execute, there will be corresponding log
information inside hns3_cmd_init.
This patch adds '(void)' Type conversion to avoid coverity warning.
Coverity issue: 349934
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
There is a coverity defect related "Argument cannot be negative".
This patch fixes it by passing '-ret' to the function strerror() when
ret is negative.
Coverity issue: 349933
Fixes: fcba820d9b ("net/hns3: support flow director")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Base on hns3 network engine, when the rte_eth_tx_burst API is called
by Upper Level Process, if PKT_TX_TCP_SEG flag is set and tso_segsz
is 0 in the input parameter structure rte_mbuf, hns3 PMD driver will
process this packet as an non-TSO packet, otherwise hardware will enter
an abnormal state.
Fixes: 6dca716c9e ("net/hns3: support TSO")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, based on hns3 network engine, driver always reports the
incoming packet's VLAN tags to the structure rte_mbuf those are the
output parameter pointers in '.rx_pkt_burst' ops implementation
function, and never reports PKT_RX_VLAN_STRIPPED flag to the structure
rte_mbuf even if Upper Level Process configured hardware strip by
calling rte_eth_dev_configure or rte_eth_dev_set_vlan_offload API
function. It makes the ULP unable to know the stripping of VLAN.
It is supposed to present the stripped flags to the mbuf ol_flags, and
report the right VLAN tag.
And as hardware constraints, the stripped VLAN tag will always in the Rx
descriptor. Even if setting a PVID based on the function, the PVID will
be reported to the Rx descriptor. So the driver need to determine which
VLAN tag should be reported to output the structure rte_mbuf in
'.rx_pkt_burst' ops implementation function named hns3_recv_pkts.
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Fixes: 411d23b9ea ("net/hns3: support VLAN")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, based on hns3 PF device, hardware will strip 2 vlan tags when
ULP calls rte_eth_dev_set_vlan_pvid API function to set a PVID whether
vlan strip related offload is turned on by calling rte_eth_dev_configure
or rte_eth_dev_set_vlan_offload API function.
When receiving a QinQ packet with the pvid tag, if ULP does not
configure the vlan strip by the method mentioned above, a layer of vlan
tag will be lost to ULP, which is not the expected result.
It is supposed to configure the vlan strip according to the upper level
process's configuration.
Fixes: 411d23b9ea ("net/hns3: support VLAN")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
When users set the length of RSS hash key greater than the supported
length by hardware, the driver should intercept and can not configure
the wrong key into the hardware.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Rx offload flag `DEV_RX_OFFLOAD_RSS_HASH` which can be used to
enable/disable PMDs write to `rte_mbuf:#️⃣:rss`. The hns3 PMD driver
already can notify the validity of `rte_mbuf:#️⃣rss` to the
application by enabling `PKT_RX_RSS_HASH` flag in `rte_mbuf::ol_flags`.
Fixes: 19a3ca4c99 ("net/hns3: add start/stop and configure operations")
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, when running testpmd application based on hns3 network engine
with csum fwd mode by "set fwd csum" command in the prompt line, sending
42 consecutive bytes of ARP packets to network port with packets
generator. But in fact hardware can't send the ARP packets and the
related logs as below:
"Preparing packet burst to failed: Invalid argument"
The hardware doesn't support transmit packets less than 60 bytes, and in
the '.tx_pkt_burst' ops implementation function named hns3_xmit_pkts
appending operation has been added for less than 60 bytes packets. So
the interception needs to be removed in the '.tx_pkt_prepare' ops
implementation function named hns3_prep_pkts.
Fixes: de620754a1 ("net/hns3: fix sending packets less than 60 bytes")
Fixes: bba6366983 ("net/hns3: support Rx/Tx and related operations")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Currently, promiscuous mode configuration are not cleared during
uninstallation based on hns3 PF device. The residual entries may cause
unnecessary bandwidth usage.
So, we need clear the PF's promisc mode status during the uninit.
Fixes: a45fd0aa0e ("net/hns3: fix Rx queue search with broadcast packet")
Fixes: d51867db65 ("net/hns3: add initialization")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
In hns3 PMD driver, the vport id 0 denote PF, and the vport id 1 denote
the first VF device of the port.
This patch adds two macros named HNS3_PF_FUNC_ID and
HNS3_1ST_VF_FUNC_ID, and replaces this two numbers to improve code
readability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Since the return value of the '.stats_reset' and '.xstats_reset'
callback function is int, when failing to issue command to firmware to
execute clear statistics, the relevant callback function should return
non-zero value.
Fixes: 8839c5e202 ("net/hns3: support device stats")
Cc: stable@dpdk.org
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
