Add the nb_rx_q and nb_tx_q values to the error message
to give details about the error.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Releasing the rx and tx queues is already done in ixgbe_dev_close()
so it does not need to be done in eth_ixgbevf_dev_uninit().
Fixes: 2866c5f1b8 ("ixgbe: support port hotplug")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
For the secondary process of DPDK to initialize ixgbevf, it will always
use the simple RX function or LRO RX function, and this behavior is not
the same RX/TX function selection logic as it is for the primary process.
Use the ixgbe_set_tx_function and ixgbe_set_rx_function to select the
RX/TX function when secondary process calls the init function for eth dev.
Fixes: 9d8a92628f ("ixgbe: remove simple scalar scattered Rx method")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Normally the auto-negotiation is supported by FW. SW need not care about
that. But on x550em_x, FW doesn't support auto-neg. As the x550em_x ports
are 10G, if we connect the port will a peer which is 1G, the link will
always be down.
We need support auto-neg by SW to avoid this link down issue. As we already
have the code to handle the link speed setting, what we need is a trigger.
When the advertised link speed changes, a PHY interruption will be
triggered. So, we should handle this interrupt and call ixgbe_handle_lasi
to set the link speed correctly.
Please be aware it's working when auto-neg is on. If the auto-neg of the
peer port is turned off and its speed is indicated manually, we should also
set the speed of our own port manually.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Add multicast promiscuous mode support on ixgbe VF driver.
Please note if we want to use this promiscuous mode, we need both PF
and VF driver to support it. The reason is this VF feature is
configged on PF.
If use kernel PF driver + dpdk VF driver, make sure kernel PF driver
support VF multicast promiscuous mode. If use dpdk PF + dpdk VF,
better make sure PF driver is the same version as VF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
It's more valuable to abstract the link read/write interface. As such,
change the following method names, and add them to a new link info
structure:
read_i2c_combined => read_link
read_i2c_combined_unlocked => read_link_unlocked
write_i2c_combined => write_link
write_i2c_combined_unlocked => write_link_unlocked
This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access.
Initially the structure is just method pointers and a bus
address.
Two functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The MDIO clock speed must be reconfigured after the MAC reset.
The MDIO clock speed becomes invalid, therefore the driver reads
invalid PHY register values. The driver now set the MDIO clock
speed prior to initializing PHY ops and again after the MAC reset.
As now the MDIO speed gets set in more than one place, make a
function for it so it will always be done correctly.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Do not set FDIRCTRL.DROP_NO_MATCH in ixgbe_init_fdir_perfect_82599(),
this bit is already set in ixgbe_set_fdir_drop_queue_82599() which
makes more sense for drivers that call that function.
This resolves an issue where packets were being dropped when switching
to perfect filters mode.
Setting this bit makes no sense in perfect filters mode for the
driver as we do not want to route all packets that don't match an FDIR
rule to a single queue and instead fall back to RSS.
Drivers that need this bit set can call ixgbe_set_fdir_drop_queue_82599()
and the ones that don't, can preserve the old behavior.
Fixes: 2241ce2816 ("ixgbe/base: add flow director drop queue")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The X550EM_a device provides the MAC_SGMII_BUSY register to
indicate when slow SGMII register writes complete. Add
definitions for the register. No definitions are provided for
the individual bits under the theory that it is better to wait
for everything to complete when needed rather than try to map
out which reads need to wait for which writes. So we should wait
when anything is marked as "busy".
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Instead of not defining the callback for set_phy_power when
manageability is enabled, put the check in the set_phy_power
function so that only turning the power off is conditional on
management, but not turning the PHY on.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch resolves an issue where VF mac address is zeroed out
in cases where the VF driver is loaded while the PF interface
is down.
The solution is to only set it when we get an ACK from the PF.
Fixes: 6202266e56 ("ixgbe/base: vf changes")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Only x550em_x V1 was supported before. Now V2 is supported.
A mask for V1 and V2 is defined and used to support both.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add new X550EM_a devices and their mac types, X550EM_a
and X550EM_a_vf.
Update the code to use the new devices and mac types.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently, ixgbe vf and pf will disable interrupt twice in
stop stage and uninit stage. It will cause an error:
testpmd> quit
Shutting down port 0...
Stopping ports...
Done
Closing ports...
EAL: Error disabling MSI-X interrupts for fd 26
Done
because the interrupt has already been disabled in stop stage.
Since it is enabled in init stage, better remove from
stop stage.
Fixes: 0eb609239e ("ixgbe: enable Rx queue interrupts for PF and VF")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The freeing of mbuf's in ixgbe is one of the observable hot spots
under load. Optimize it by doing bulk free of mbufs using code similar
to i40e and fm10k.
Drop the no longer needed micro-optimization for the no refcount flag.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This brings the DPDK igb driver inline with the behavior used by
the current Linux driver. The IGB hardware has several different
MAC types and the threshold values that work vary based on the hardware.
Since DPDK 1.8 it has been up to devices to provide the correct default
configuration parameter. But the igb driver gives values that are broken
on some devices, and always causes a warning message at startup.
Please test this on real hardware, I don't have the luxury of a
hardware lab full of variations of this chip.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Allow reprogramming of the RAR with a zero mac address,
to ensure that the VF traffic goes to the PF after
stop, close and detach of the VF.
Fixes: be2d648a2d ("igb: add PF support")
Fixes: d82170d279 ("igb: add VF support")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Enable promiscuous and allmulticast mode control from the VF using
rte_eth_promiscuous_enable()/rte_eth_promiscuous_disable() and
rte_eth_allmulticast_enable()/rte_eth_allmulticast_disable().
For promiscuous mode host/PF igb driver should be built with
IGB_ENABLE_VF_PROMISC.
For allmulticast mode "allmulti" flag should be set for appropriate PF
ifconfig eth0 allmulti
Signed-off-by: Yury Kylulin <yury.kylulin@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Modified driver and eal code to support I217 and I218 Intel NICs.
Compiled and tested (via testpmd) on Ubuntu 14.04 for target
x86_64-native-linuxapp-gcc
Compiled for target x86_64-native-linuxapp-clang
Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The last packet of the tx burst function array was not being
emitted until the subsequent call. The nic descriptor index
was being set to the current tx descriptor instead of one past
the descriptor as required by the nic.
Fixes: d739ba4c6a ("enic: improve Tx packet rate")
Signed-off-by: John Daley <johndale@cisco.com>
This is a wholesale replacement of the Enic PMD receive path in order
to improve performance and code clarity. The changes are:
- Simplify and reduce code path length of receive function.
- Put most of the fast-path receive functions in one file.
- Reduce the number of posted_index updates (pay attention to
rx_free_thresh)
- Remove the unneeded container structure around the RQ mbuf ring
- Prefetch next Mbuf and descriptors while processing the current one
- Use a lookup table for converting CQ flags to mbuf flags.
Signed-off-by: John Daley <johndale@cisco.com>
The enic PMD driver send function uses a constant offset instead
of relying on the data_off in the mbuf to find the start of the packet.
Fixes: fefed3d1e6 ("enic: new driver")
Signed-off-by: Yoann Desmouceaux <ydesmouc@cisco.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Chelsio NIC ports share a single PF. Move rte_eth_copy_pci_info()
to copy the pci device information to the remaining ports as well.
Also update license year to 2016.
Fixes: eeefe73f0a ("drivers: copy PCI device info to ethdev data")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
max_rx_pkt_len already includes ETHER_HDR_LEN and ETHER_CRC_LEN for the
mtu. But, the firmware also adds ETHER_HDR_LEN and ETHER_CRC_LEN to the
mtu specified. Fix by subtracting these values from the mtu before
passing it to firmware.
Fixes: 4b2eff452d ("cxgbe: enable jumbo frames")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
The size of each entry in the port's rss table is actually 2 bytes
and not 1 byte. A segfault occurs when accessing part of port 0's rss
table because it gets overwritten by subsequent port 1's part of the
rss table. Fix by setting the size of each entry appropriately.
Fixes: 92c8a63223 ("cxgbe: add device configuration and Rx support")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
The VF needs to determine the queues sizes before .dev_infos_get
so that it can hint to the upper layer the proper sizes. Move
bnx2x_vf_get_resources() to .eth_dev_init and probe with the guesses
from bnx2x_init_rte().
Signed-off-by: Chas Williams <3chas3@gmail.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
bnx2x_loop_obtain_resources() returns a struct containing the status and
the error message. If bnx2x_do_req4pf() fails, it shouldn't return both
of these fields set to 0 indicating failure and no error.
Further, bnx2x_do_req4pf() needs to be able fail and return NO_RESOURCES
so that bnx2x_loop_obtain_resources() can negotiate reduced resource
requirments. This requires additional checking around bnx2x_do_req4pf().
Fixes: 540a211084 ("bnx2x: driver core")
Signed-off-by: Chas Williams <3chas3@gmail.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
The mbuf_alloc_size is leftover from BSD or some other code base.
It is set but never used in DPDK driver. After that the related defines
can also be eliminated.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Harish Patil <harish.patil@qlogic.com>
Fixes: the hung/crash issue when quitting testpmd under high
traffic rate. The following issue were found and fixed.
1. edesc->size is not initialized properly in mpipe_do_xmit() and could
cause buffer leak or corruption when HW buffer return is used.
2. Check the 'idesc.be' error bit in mpipe_recv_flush() to make sure
buffer is valid before releasing it. This is to avoid issues when
running out of buffers.
3. priv->rx_buffers counter is not accurate when HW buffer return is
used. Remove this counter to simplify the code.
Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
Mpipe link structure is initialized in function mpipe_link_init().
Currently it's only called from the eth_dev_ops.dev_start, which
caused crashes when link mgmt APIs (like promiscuous_enable)
was called before eth_dev_ops.dev_start(). This submit fixed it
by calling mpipe_link_init() in rte_pmd_mpipe_devinit().
Fixes: a8dd50513d ("mpipe: add TILE-Gx mPIPE poll mode driver")
Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
This submit has changes to optimize the mpipe buffer return. When
a packet is received, instead of allocating and refilling the
buffer stack right away, it tracks the number of pending buffers,
and use HW buffer return as an optimization when the pending
number is below certain threshold, thus save two MMIO writes and
improves performance especially for bidirectional traffic case.
Signed-off-by: Liming Sun <lsun@ezchip.com>
Acked-by: Zhigang Lu <zlu@ezchip.com>
Declare dst as type uint32_t instead of uint64_t, otherwise, we will get
a random upper 32 bit feature bits, as the following io port read reads
lower 32 bit only. It could lead a feature bits that include VIRTIO_F_VERSION_1
(the 32th bit) for legacy virtio, which is obviously wrong.
Fixes: b8f04520ad ("virtio: use PCI ioport API")
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Jianfeng Tan <jianfeng.tan@intel.com>
Reviewed-by: David Marchand <david.marchand@6wind.com>
Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The patch add VxLAN & NVGRE TX checksum off-load. When the flag of
outer IP header checksum offload is set, we'll set the context
descriptor to enable this checksum off-load.
Also update release notes for VxLAN & NVGRE checksum off-load support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
X550 will do VxLAN & NVGRE RX checksum off-load automatically.
This patch exposes the result of the checksum off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add UDP tunnel port add/del support on ixgbe. Now only
support VxLAN port configuration.
Although according to the specification the VxLAN port has
a default value 4789, it can be changed. We support VxLAN
port configuration to meet the change.
Note, the default value of VxLAN port in ixgbe NICs is 0. So
please set it when using VxLAN off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The names of function for tunnel port configuration are not
accurate. They're tunnel_add/del, better change them to
tunnel_port_add/del.
The old functions are directly replaced because the API and ABI
compatibility of ethdev are already broken in 16.04.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add support of l2 tunnel configuration and operations.
1, Support modifying ether type of a type of l2 tunnel.
2, Support enabling and disabling the support of a type of l2 tunnel.
3, Support enabling/disabling l2 tunnel tag insertion/stripping.
4, Support enabling/disabling l2 tunnel packets forwarding.
5, Support adding/deleting forwarding rules for l2 tunnel packets.
Only support E-tag now.
Also update the release note.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
On X550, as required by datasheet, E-tag packets are not expected
when double VLAN are used. So modify the register PFVTCTL after
enabling double VLAN to select pool by MAC but not MAC or E-tag.
An introduction of E-tag:
It's defined in IEEE802.1br. Please reference this website,
http://www.ieee802.org/1/pages/802.1br.html.
A brief description.
E-tag means external tag, and it's a kind of l2 tunnel. It means a
tag will be inserted in the l2 header. Like below,
|31 24|23 16|15 8|7 0|
0| Destination MAC address |
4| Dest MAC address(cont.) | Src MAC address |
8| Source MAC address(cont.) |
12| E-tag Etherenet type (0x893f) | E-tag header |
16| E-tag header(cont.) |
20| VLAN Ethertype(optional) | VLAN header(optional) |
24| Original type | ...... |
...| ...... |
The E-tag format is like below,
|0 15|16 18|19 |20 31|
| Ethertype - 0x893f | E-PCP |DEI| Ingress E-CID_base |
|32 33|34 35|36 47|48 55 |56 63|
| RSV | GRP |E-CID_base|Ingress_E-CID_ext| E-CID_ext |
The Ingess_E-CID_ext and E-CID_ext are always zero for endpoints
and are effectively reserved.
The more details of E-tag is in IEEE 802.1BR. 802.1BR is used to
replace 802.1Qbh. 802.1BR is a standard for Bridge Port Extension.
It specifies the operation of Bridge Port Extenders, including
management, protocols, and algorithms. Bridge Port Extenders
operate in support of the MAC Service by Extended Bridges.
The E-tag is added to l2 header to identify the VM channel and
the virtual port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
The array 'ptype_table' was defined in depth of 'UINT8_MAX' which
is 255, while the querying index could be from 0 to 255. The issue
can be fixed with expanding the array to one more element.
Fixes: 9571ea0284 ("i40e: replace some offload flags with unified packet type")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
virtio PMD could use IO port to configure the virtio device without
using UIO/VFIO driver in legacy mode.
There are two issues with previous implementation:
1) virtio PMD will take over the virtio device(s) blindly even if not
intended for DPDK.
2) driver conflict between virtio PMD and virtio-net kernel driver.
This patch checks if there is kernel driver other than UIO/VFIO managing
the virtio device before using port IO.
If legacy_virtio_resource_init fails and kernel driver other than
VFIO/UIO is managing the device, return 1 to tell the upper layer we
don't take over this device.
For all other IO port mapping errors, return -1.
Note than if VFIO/UIO fails, now we don't fall back to port IO.
Fixes: da978dfdc4 ("virtio: use port IO to get PCI resource")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: David Marchand <david.marchand@6wind.com>
PCIe feature of 'Extended Tag' is important for 40G performance.
It adds its enabling during each port initialization, to ensure
the high performance.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Fixed issue of byte order in ethdev library that the structure
for setting fdir's mask and flow entry is inconsist and made
inputs of mask be in big endian.
Fixes: 2d4c1a9ea2 ("ethdev: add new flow director masks")
Fixes: 76c6f89e80 ("ixgbe: support new flow director masks")
Reported-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Macros RTE_MBUF_DATA_DMA_ADDR and RTE_MBUF_DATA_DMA_ADDR_DEFAULT
are defined in each PMD driver file. Convert macros to inline
functions and move them to common lib/librte_mbuf/rte_mbuf.h file.
PMD drivers include rte_mbuf.h file directly/indirectly hence no
additioanl header file inclusion is necessary.
Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
ConnectX-4 NICs can handle at most 512 entries in RETA table.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The physically linked-together combined library has been an increasing
source of problems, as was predicted when library and symbol versioning
was introduced. Replace the complex and fragile construction with a
simple linker script which achieves the same without all the problems,
remove the related kludges from eg mlx drivers.
Since creating the linker script is practically zero cost, remove the
config option and just create it always.
Based on a patch by Sergio Gonzales Monroy, linker script approach
initially suggested by Neil Horman.
Suggested-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move all os / arch specifics to eal.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reviewed-by: Santosh Shukla <sshukla@mvista.com>
Tested-by: Santosh Shukla <sshukla@mvista.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
According to the api, rte_eal_pci_map_device is only successful when
returning 0.
Fixes: 6ba1f63b5a ("virtio: support specification 1.0")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Fixes: c52afa68d7 ("virtio: move left PCI stuff in the right file")
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The file rte_config.h is automatically generated and included.
No need to #include it.
The example performance-thread needs a makefile fix to avoid
overwriting the default cflags.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
As discussed on list, switch numbering scheme to be based on year/month.
Release 2.3 then becomes 16.04.
Ref: http://dpdk.org/ml/archives/dev/2015-December/030336.html
Also, added zero padding to the month so that it appear as 16.04 and
not 16.4 in "make showversion" and rte_version().
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
fix the error reported by checkpatch:
"ERROR: return is not a function, parentheses are not required"
remove parentheses in return like:
"return (logical expressions)"
remove parentheses in return a function like:
"return (rte_mempool_lookup(...))"
Fixes: 6307b909b8 ("lib: remove extra parenthesis after return")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
Modern (v1.0) virtio pci device defines several pci capabilities.
Each cap has a configure structure corresponding to it, and the
cap.bar and cap.offset fields tell us where to find it.
Firstly, we map the pci resources by rte_eal_pci_map_device().
We then could easily locate a cfg structure by:
cfg_addr = dev->mem_resources[cap.bar].addr + cap.offset;
Therefore, the entrance of enabling modern (v1.0) pci device support
is to iterate the pci capability lists, and to locate some configs
we care; and they are:
- common cfg
For generic virtio and virtqueue configuration, such as setting/getting
features, enabling a specific queue, and so on.
- nofity cfg
Combining with `queue_notify_off' from common cfg, we could use it to
notify a specific virt queue.
- device cfg
Where virtio_net_config structure is located.
- isr cfg
Where to read isr (interrupt status).
If any of above cap is not found, we fallback to the legacy virtio
handling.
If succeed, hw->vtpci_ops is assigned to modern_ops, where all
operations are implemented by reading/writing a (or few) specific
configuration space from above 4 cfg structures. And that's basically
how this patch works.
Besides those changes, virtio 1.0 introduces a new status field:
FEATURES_OK, which is set after features negotiation is done.
Last, set the VIRTIO_F_VERSION_1 feature flag.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
The mergeable virtio net hdr format has been the standard and the
only virtio net hdr format since virtio 1.0. Therefore, we can
not hardcode hdr_size to "sizeof(struct virtio_net_hdr)" any more
at virtio_recv_pkts(), otherwise, there would be a mismatch of
hdr size from rte_vhost_enqueue_burst() and virtio_recv_pkts(),
leading a packet corruption.
Instead, we should retrieve it from hw->vtnet_hdr_size; we will
do proper settings at eth_virtio_dev_init() in later patches.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
Switch to 64 bit features, which virtio 1.0 supports.
While legacy virtio only supports 32 bit features, it complains aloud
and quit when trying to setting > 32 bit features.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
virtio_pci.c is a more proper place for pci stuff; virtio_ethdev is not.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
Introduce struct virtio_pci_ops, to let legacy virtio (v0.95) and
modern virtio (1.0) have different implementation regarding to a
specific pci action, such as read host status.
With that, this patch reimplements all exported pci functions, in
a way like:
vtpci_foo_bar(struct virtio_hw *hw)
{
hw->vtpci_ops->foo_bar(hw);
}
So that we need pay attention to those pci related functions only
while adding virtio 1.0 support.
This patch introduced a new vtpci function, vtpci_init(), to do
proper virtio pci settings. It's pretty simple so far: just sets
hw->vtpci_ops to legacy_ops as we don't support 1.0 yet.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
offset arg of vtpci_read/write_dev_config is derived from offsetof(),
which is of size_t type, instead of uint64_t. So, define it as size_t
type.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
As we have already set up it at virtio_dev_queue_setup(), and a vq
restart will not reset the settings.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Qian Xu <qian.q.xu@intel.com>
Reviewed-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Tested-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Huawei Xie <huawei.xie@intel.com>
The x550 MDIO clock speed must be configured prior to first MDIO read or
write. The default MDIO clock speed is not valid, therefore the driver
is configuring a valid speed prior to reading the copper PHY device id.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_X550em. Since
this function is meant to initialize function pointers for detected PHY
type. Internal PHY reset was moved to ixgbe_setup_internal_phy_t_x550em
which will now detect which mode does internal PHY work in, and setup it
as required.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
KR auto-neg mode is what we will be using going forward. The SW
interface for this mode is different than what was used for iXFI.
While debugging, it was determined that the ucode diagnostic was
no longer needed. This code has been removed to simplify the init
flow.
A subtle semaphore error in the CS4227 reset flow was fixed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch changes code to use registers offsets stored in mvals table
instead of values defined statically.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds ixgbe_set_fdir_drop_queue_82599 for enabling and
setting flow director drop queue, and adds sets drop no match in
ixgbe_init_fdir_perfect_82599 for x550.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Waiting for FDIRCMD completion is an expensive thing to do in the
transmit hot path. This wait was added to catch problems with perfect
filter rules, and, at least in the Linux driver, there is no error
check anyway, so there is no point to adding the delay. So do not wait
for completion. Change the return of the function to void, since it has
no meaningful return value.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds the flow control ethertype to the defines for the
ETQF filter list. This only adds the define. Each driver
can add this ethertype to the filter. This is needed to prevent
denial of service by malicious VFs sending out flow control
packets.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently credit_refill and credit_max could be zero for a TC and that
is causing Tx hang for CEE mode configuration, so to fix that have at
min credit assigned to a TC and that is as what IEEE mode already does.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Coverity issue reported like
CID 119268 (#1 of 1): Unintended sign extension
(SIGN_EXTENSION)sign_extension: Suspicious implicit sign extension:
vsi_id with type unsigned short (16 bits, unsigned) is promoted in
vsi_id << 23 to type int (32 bits, signed), then sign-extended to type
unsigned long (64 bits, unsigned). If vsi_id << 23 is greater than
0x7FFFFFFF, the upper bits of the result will all be 1.
Fixes: 88ebc2b7f9 ("i40e: extend flow director to support VF")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
In FreeBsd driver, the max frame size is changed to MTU, but not
keep the default value defined in DataSheet. When DPDK runs on that
NIC, the configured value is not expected.
This patch sets the max frame size to default when initialization.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This counter was left unmodified. Restore it in ixgbe_dev_stats_get.
The ierrors counter still includes imissed for ixgbe. This behaviour is
not consistent amongst all drivers. Another patch may be needed to unify
the meaning of the ierrors counter.
Fixes: 5e50ad1c1b ("ixgbe: add specific stats")
Signed-off-by: Robin Jarry <robin.jarry@6wind.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Fragmented IPv4 packets have no TCP/UDP headers, so we hashed
random data introducing reordering of the fragments.
Signed-off-by: Andriy Berestovskyy <aber@semihalf.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
The following messages might appear after some idle time:
"PMD: Failed to allocate LACP packet from pool"
The fix ensures the mempool size is greater than the sum
of TX descriptors.
Signed-off-by: Andriy Berestovskyy <aber@semihalf.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Add BNX2X PMD version, print it as part of adapter info.
Adjusted print adapter info output formatting.
This patch versions BNX2X PMD at 1.0.0.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
The periodic debug option is used to collect periodic
events like statistics, register access etc and won't
interfere with user-level messages.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Fix for the following clang build error:
drivers/net/bnx2x/elink.c:10384:41: error: shifting a
negative signed value is undefined [-Werror,-Wshift-negative-value]
vars->eee_status &= ~SHMEM_EEE_1G_ADV <<
~~~~~~~~~~~~~~~~~ ^
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
SR-IOV is supported using bnx2x poll mode driver running as VF driver and
native linux driver running as PF (in host/hypervisor). There is no issue
while running with the PF driver which is at the base version as that of
PMD. However, there is a compatibility issue between newer out-of-box PF
drivers with older VF driver. So the newer VFs would also need to send
BNX2X_VF_TLV_PHYS_PORT_ID (among other TLVs) to differentiate between
newer and older VFs.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
If you stop and start the driver, the rx queue will have the previous
index values when programming the adapter. Therefore, we should always
reset the queue indices when the rx ring is setup. Note: We need to
clear (write) the status block's completion queue index since it is
possibly in a read cache.
Tidy some init code to make it clearer what the defaults are.
Signed-off-by: Chas Williams <3chas3@gmail.com>
When refilling freelists for the first time and if it fails, the rxq
is freed and returns ENOMEM. There is a check while freeing hardware rxq
to pass freelist context id if the freelist exists or 0xffff otherwise.
The error path is only reached if freelist exists. So, fix is to remove
the useless check for freelist existence.
Coverity issue: 107108
Fixes: 92c8a63223 ("cxgbe: add device configuration and Rx support")
Reported-by: John McNamara <john.mcnamara@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
It corrects the input set values to be set for vlan or
double vlan.
Fixes: 98f0557076 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
We should provide VIRTIO_PCI_QUEUE_SEL with vq->vq_queue_idx,
but not vq->queue_id.
vq->queue_id is the queue id from rte_eth_rx/tx_queue_setup(),
which always starts from 0 no matter which queue it is. However,
for virtio, even number is for RX queue, and odd number is for
TX queue.
Fixes: 5382b188fb ("virtio: add queue release")
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Check sc->state to prevent double init.
If the link is up, then the driver cannot be stopped and started
successfully. Instead of checking the link status, use the driver's
state.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Similar to commit 5f9115e58c, but
for qat and mpipe drivers. The former did not exist when the
previous patch was sent and latter I just missed.
Fixes: 5f9115e58c ("mk: fix shared library dependencies of drivers")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Aaron Conole <aconole@redhat.com>
The standard for DPDK is to use memset() not bzero which
is a leftover BSD-ism.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This is one of those trivial things git and other tools complain
about.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The rx_mbuf_alloc_failed counter was only cleared by virtio driver.
Now it is cleared by common rte_eth_stats_reset function for all
drivers at once.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
call rte_eth_copy_pci_info() after the RTE_PCI_DRV_INTR_LSC
has been initialised.
Fixes: eeefe73f0a ("drivers: copy PCI device info to ethdev data")
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
The space check for transmit ring only needs a single conditional.
I.e only need to recheck for space if there was no space in first check.
This can help performance and simplifies loop.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The virtio driver was not initializing all the fields in
the receive mbuf. This would cause bugs where previous usage
of mbuf would leave stale TCI and offload flags.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
The original was always setting unicast. While here, clean up some
other references that also point into the Ethernet header.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Acked-by: Harish Patil <harish.patil@qlogic.com>
The upcoming Hyper-V driver converts the pci_drv element
in struct eth_driver to a union. When vmbus is added the
pci_drv needs to be explicit. Easier to fix the issue
ahead of time.
This is backwards compatible with previous code.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
When dev_stop is called in i40evf pmd driver, queues are switched off
to stop receiving and transmitting. But the mac address of this VF
still exists in VEB switch.
To stop the traffic from VSI level, the mac address need to be removed
too. Then the bandwidth for this SRIOV VSI can be freed.
This patch fix this issue.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch fixes tx byte statistics when transmitting packets
with link down.
Previously, the counter would decrement 4 bytes for each packet that
was transmitted with link down, causing the uint64 to wrap around.
Fixes: c03fcee9ab ("ixgbe: remove CRC size from byte counters")
Reported-by: Michael Qiu <michael.qiu@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Similar to commit 113c8e13c4, but
for bnx2x, pcap, sze2data and xenvirt PMDs.
Requiring applications to know about library internal details like
dependencies to external helper libraries is a limitation of
static linkage, shared libraries should always know their own
dependencies for sane operation. This is especially highlighted
with dlopen()'ed items, having applications link against about plugin
internal dependencies goes on the side of absurd.
Note that linking with a shared combined library still requires to
know the internal dependencies.
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
There is a new function in the EAL API for internal use.
It has neither a proper prefix nor a .map export:
libethdev.so: undefined reference to `is_xen_dom0_supported'
Fixes: 719dbebceb ("xen: allow determining DOM0 at runtime")
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Parallel build of bonding driver can fail because of
missing dependency.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Declan Doherty <declan.doherty@intel.com>
There is a compilation issue with some compilers.
In i686 platform, long is 32bit, so XXX_CYCLECOUNTER_MASK
need define as 'ULL'
Fixes: 9c857bf6be ("igb: support ieee1588 functions for device time")
Fixes: 1c4445e1f2 ("ixgbe: support ieee1588 functions for device time")
Fixes: f3a4e40eca ("i40e: support ieee1588 functions for device time")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
After introducing vPMD feature, fm10k driver will select best
Rx/Tx in running time. Original implementation selects Rx/Tx
silently without notifications.
This patch adds debug info to notify user what actual Rx/Tx
func are used.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Steps to reproduce the bug:
1. All Rx offloading is disabled and start the device, then
Vector Rx is used.
2. Stop the device. Re-configure to enable hw_ip_checksum = 1,
start the device again.
3. In this case, assume regular Rx should be used since Vector
Rx doesn't support ip checksum offload. But actually Vector
Rx is used and cause checksum won't be done by hardware.
The reason is after re-configuring, driver misses an "else" in
func fm10k_set_rx_function(). Then Rx func in last round are
used.
Fixes: 77a8ab47eb ("fm10k: select best Rx function")
Reported-by: Xiao Wang <xiao.w.wang@intel.com>
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
It fixes the issue of not configuring rss key enable flags
when there is no rss key available.
Fixes: 647d1eaf75 ("i40evf: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
If use DPDK PF + DPDK VF on igb NICs, we find the MAC address of VF
port is always 0. Because we forget to give it a value if this MAC
address is not assigned by PF. This patch'll assign a random MAC
address to igb VF port as ixgbe does.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Without .map file, compiling error occurs when
CONFIG_RTE_BUILD_SHARED_LIB is enabled.
Reported-by: Guo Xin <gxin@ezchip.com>
Signed-off-by: Zhigang Lu <zlu@ezchip.com>
Secondary processes are expected to use queues and other resources
allocated by the primary, however Verbs resources can only be shared
between processes when inherited through fork().
This limitation can be worked around for TX by configuring separate queues
from secondary processes.
Signed-off-by: Or Ami <ora@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The number of available entries in TX rings is taken before performing
completion, effectively making rings smaller than they are and causing
TX performance issues under load.
Fixes: 2e22920b85 ("mlx5: support non-scattered Tx and Rx")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The number of available entries in TX rings is taken before performing
completion, effectively making rings smaller than they are and causing
TX performance issues under load.
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
When MP to MR cache is full, the last (newest) MR is freed instead of the
first (oldest) one, causing local protection errors during TX.
Fixes: 2e22920b85 ("mlx5: support non-scattered Tx and Rx")
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
When MP to MR cache is full, the last (newest) MR is freed instead of the
first (oldest) one, causing local protection errors during TX.
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Pre-registering mbuf memory pools when creating TX queues avoids costly
registrations later in the data path.
Fixes: 2e22920b85 ("mlx5: support non-scattered Tx and Rx")
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Pre-registering mbuf memory pools when creating TX queues avoids costly
registrations later in the data path.
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Signed-off-by: Olga Shern <olgas@mellanox.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Buffers with too many segments are linearized to overcome
MLX5_PMD_SGE_WR_N, unfortunately the last segment is never sent.
Fixes: 3ee8444608 ("mlx5: support scattered Rx and Tx")
Signed-off-by: Jesper Wramberg <jesper.wramberg@gmail.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Buffers with too many segments are linearized to overcome
MLX4_PMD_SGE_WR_N, unfortunately the last segment is never sent.
Fixes: be11b35817 ("mlx4: move scattered Tx processing to helper function")
Signed-off-by: Jesper Wramberg <jesper.wramberg@gmail.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Indirect mbuf data may come from a different mempool which must be
registered separately as another memory region, otherwise such mbufs cannot
be sent.
Fixes: 2e22920b85 ("mlx5: support non-scattered Tx and Rx")
Signed-off-by: Jesper Wramberg <jesper.wramberg@gmail.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Indirect mbuf data may come from a different mempool which must be
registered separately as another memory region, otherwise such mbufs cannot
be sent.
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Signed-off-by: Jesper Wramberg <jesper.wramberg@gmail.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
A typo causes TX stats indices to be retrieved from RX queues.
Fixes: 87011737b7 ("mlx5: add software counters")
Reported-by: Nicolas Harnois <nicolas.harnois@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
A typo causes TX stats indices to be retrieved from RX queues.
Fixes: 7fae69eeff ("mlx4: new poll mode driver")
Reported-by: Nicolas Harnois <nicolas.harnois@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
CXGBE PMD depends on an alarm to periodically transmit any pending
coalesced packets and hence spins for a lock for each tx queue in the
alarm callback.
A better solution is to try to get a lock whenever possible, instead
of spinning for it.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Most dpdk examples and apps seem to initialize with a minimum of 128 rx
descriptors and 512 tx descriptors for queue setup. However, CXGBE PMD
enforces a minimum of 1024 descriptors. This causes the dpdk stack
to return -EINVAL because the apps do not request the minimum required.
The fix is to relax this enforcing in CXGBE PMD. A minimum of 128
descriptors seems to be a good number with the least impact on the
performance.
Fixes: 946c9ed956 ("cxgbe: get descriptor limits")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
The vector number may change during 'dev_start'. Before enabling a new vector mapping,
it's necessary to disable/unmap the previous setting.
Fixes: 7ab8500037 ("ixgbe: fix VF start with PF stopped")
Reported-by: Yong Liu <yong.liu@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The vector number may change during 'dev_start'.
Before enabling a new vector mapping,
it's necessary to disable/unmap the previous setting.
Fixes: fe685de2b1 ("igb: fix VF start with PF stopped")
Reported-by: Yong Liu <yong.liu@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
fm10k driver will meet compile error on non-x86 platforms due to
SSE instructions. Original implementation didn't have switch to
turn off vPMD.
The improvement introduces a macro to turn on/off vPMD functions,
it's on by default. On non-x86 platforms, it can simply be turned
off to fix compile issue.
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
When the fm10k port is closed, both func tx_queue_clean() and
fm10k_tx_queue_release_mbufs_vec() will try to release buffer in
SW ring. The latter func won't do sanity check on those pointers
and cause crash.
The fix removed Vector TX buffer release func since it can share
the release functions with regular TX.
Fixes: fb9066e479 ("fm10k: reset and release mbuf for vector Tx")
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Michael Qiu <michael.qiu@intel.com>
vlan_tci should be copied from RX descriptor to mbuf,
and flag PKT_RX_VLAN_PKT should be set for every RX packet,
this patch fixes this issue.
Packets in fm10k device always carry at least one VLAN tag.
For those packets coming in without VLAN tag,
the port default VLAN tag will be used.
So in fm10k, always PKT_RX_VLAN_PKT flag is set and vlan_tci
is valid for each RX packet's mbuf.
Signed-off-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
For i40e vf driver, should use I40EVF_WRITE_FLUSH to flush
configuration but not I40E_WRITE_FLUSH. This patch fixed this issue.
Fixes: be6c228d4d (i40evf: support Rx interrupt)
Reported-by: Qian Xu <qian.q.xu@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
If DCB is not enabled, the BW info is not stored for VSI. This
patch fixes this issue by merging functions i40e_vsi_dump_bw_config
and i40e_vsi_get_bw_info together.
Fixes: c8b9a3e3fe (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
When NVM version is updated to 5.x, DCB can not be configured. This
issue is because of the FW version validation is not correct.
This patch fixed this issue.
Fixes: c8b9a3e3fe (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yulong Pei <yulong.pei@intel.com>
As firmware does not support any link control from software driver
side, any phy config should be ignored as a workaround. Otherwise
the link might not be up again after binding back to kernel driver.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It fixes the issue of not re-configuring hash enable flags (HENA)
if there is no key.
Fixes: d0a349409b ("i40e: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes the crc bytes from byte counter statistics.
Doing so fixes a bug that CRC bytes were included on TX but not
on RX, causing mismatch of bytes received / sent.
Fixes: 9aace75fc8 ("i40e: fix statistics")
Reported-by: Weichun Chen <weichunx.chen@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch removes the crc bytes from byte counter statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch removes the crc bytes from byte counter statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This fixes a bug added to em and igb drivers which causes the pci info
seen by the primary process to become invalidated by secondary process
startup.
This call was added after the process type check in the other drivers.
Fixes: eeefe73f0a ("drivers: copy PCI device info to ethdev data")
Signed-off-by: Jon DeVree <nuxi@vault24.org>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
When freeing the device it is also neccesary to free
rx_queues and tx_queues
Signed-off-by: Mauricio Vasquez B <mauricio.vasquezbernal@studenti.polito.it>
Add virtual PMD which communicates with COMBO cards through sze2
layer using libsze2 library.
Since link_speed is uint16_t, there can not be used number for 100G
speed, therefore link_speed is set to ETH_LINK_SPEED_10G until the
type of link_speed is solved.
Signed-off-by: Matej Vido <matejvido@gmail.com>
This commit introduce rte_smp_mb(), rte_smp_wmb() and rte_smp_rmb(), in
order to enable memory barriers between lcores.
The patch does not provide any functional change for IA, the goal is to
have infrastructure for weakly ordered machines like ARM to work on DPDK.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Use common code to handle Xen support at runtime.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
These statistics are marked deprecated, leave them alone.
Also keep track of imissed across all ports.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch refactors the queue and priority statistic handling.
Generic queue stats are presented by rte_eth_xstats_get(), and the
i40e_xstats_get() exposes only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This patch refactors the queue handling. Generic queue stats are
handled by rte_eth_xstats_get() and the ixgbe_xstats_get() exposes
only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
It fixes the issue of trying to allocate more VSIs for VMDq than
hardware remaining. It adds a check of the hardware remaining
before allocating VSIs for VMDq.
Fixes: c80707a0fd ("i40e: fix VMDq pool limit")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
ICC complains about enumerated types being mixed in link bonding driver,
as ETH_MQ_RX_RSS is an enum type of mq_mode and not a bitmask as it was
being treated.
Fixes: 734ce47f71 ("bonding: support RSS dynamic configuration")
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
One of the ways to reproduce the issue:
testpmd <EAL-OPTIONS> -- -i --txqflags=0
testpmd> set fwd txonly
testpmd> set txpkts 64,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4
testpmd> set txsplit rand
testpmd> start
After some time TX on ixgbe queue will hang,
and all packet transmission on that queue will stop.
This bug was first reported and investigated by
Vlad Zolotarov <vladz@cloudius-systems.com>:
"We can reproduce this issue when stressed the xmit path with a lot of highly
fragmented TCP frames (packets with up to 33 fragments with non-headers
fragments as small as 4 bytes) with all offload features enabled."
The root cause is that ixgbe_xmit_pkts() in some cases violates the HW rule
that the distance between TDs with RS bit set should not exceed 40 TDs.
>From the latest 82599 spec update:
"When WTHRESH is set to zero, the software device driver should set the RS bit
in the Tx descriptors with the EOP bit set and at least once in the 40
descriptors."
The fix is to make sure that the distance between TDs with RS bit set
would never exceed HW limit.
As part of that fix, tx_rs_thresh for ixgbe PMD is not allowed to be greater
then to 32 to comply with HW restrictions.
With that fix slight slowdown for the full-featured ixgbe TX path
might be observed (from our testing - up to 4%).
ixgbe simple TX path is unaffected by that patch.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch fixes a bug where only some of the statistics were being
reset when calling rte_eth_stats_reset() or rte_eth_xstats_reset().
As both the stats reset and xstats reset do the same, refactor away
the duplicated function.
This patch marks the VSI to update its offset, causing the stats be
look like they are reset.
Fixes: 9aace75fc8 ("i40e: fix statistics")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This fixes the issue of not freeing memzone in a call to free the
memory for adminq DMA.
Fixes: 4861cde461 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
It fixes the issue of cannot using more than 1 poor for VMDq,
according to the queues left.
Fixes: 705b57f820 ("i40e: enlarge the number of supported queues")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Fix for the following error on icc 2015, due to incorrect type:
drivers/net/i40e/i40e_fdir.c(1376): error #188:
enumerated type mixed with another type
case RTE_ETH_FDIR_FILTER_INPUT_SET_SELECT:
Fixes: 98f05570 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It fixes compile issue on ICC 13.0.0.
Error logs:
i40e_ethdev.c(7943): error #188: enumerated type mixed with another type
Fixes: c8b9a3e3fe ("i40e: support DCB mode")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Once posted through mailbox, we must check for nack from the PF
and report an error in this case.
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Report an error when something went wrong.
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Sujith Sankar <ssujith@cisco.com>
In case of creating bond device without add any slaves and
quit from testpmd, application crashed since rx/tx queues
are NULL.
Add checking of this parameters before trying to free.
Signed-off-by: Raslsn Darawsheh <rdarawsheh@asaltech.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Add support for RTE_ETH_FDIR_PASSTHRU flow director behavior so
output queue is assigned by other filters.
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes l3_l4_xsum_errors from rx errors.
The reason to remove it is that UDP packets have an optional checksum, and
when not calculated the checksum field should be set to zero. When the
checksum is not calculated (zero-ed out), the hardware still counts a valid
UDP packet as an l3_l4_xsum_error.
This hardware issue is documented in 82599 errata, titled:
"Integrity Error Reported for IPv4/UDP Packets with Zero Checksum"
The solution is to remove l3_l4_xsum_errors from rx_errors, as discussed on
http://thread.gmane.org/gmane.comp.networking.dpdk.devel/25590/
Fixes: f6bf669b99 ("ixgbe: account more Rx errors")
Suggested-by: Martin Weiser <martin.weiser@allegro-packets.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
