* Add a couple of RX errors;
* Add the spectral scan PHY error code;
* extend the RX flags to be a 16 bit field, rather than an 8 bit field;
* Add a new RX flag.
Obtained from: Qualcomm Atheros
The AR93xx and later chips support two RX FIFO queues - a high and low
priority queue.
For legacy chips, just assume the queues are high priority.
This is inspired by the reference driver but is a reimplementation of
the API and code.
as an EDMA check function.
For the AR9003 and later NICs, different TX/RX DMA and descriptor handling
code will be conditional on the EDMA check.
Obtained from: Qualcomm Atheros
* Add a new ANI variable, for AR9003 and later chips;
* The AR9003 and later series chips support two RX queues now, so start
down the road of supporting that;
* Add some new TX queue types - uAPSD is possible on earlier chips,
but PAPRD is relevant to AR9003 and later.
Obtained from: Qualcomm Atheros, Linux ath9k
with AMPDU aggregate delimiters.
If there's an OFDM restart during an aggregate, the hardware ACKs
the previous frame, but communicates the RXed frame to the hardware
as having had CRC delimiter error + OFDM_RESTART phy error.
The frame however didn't have a CRC error and since the hardware ACKed
the aggregate to the sender, it thinks the frame was received.
Since I have no idea how often this occurs in the real world, add a
debug statement so trigger whenever this occurs. I'd appreciate an
email if someone finds this particular situation is triggered.
The Linux ath9k btcoex code is based off of this code.
Note this doesn't actually implement functional btcoex; there's some
driver glue and a whole lot of verification that is required.
On the other hand, I do have the AR9285+BT and AR9287+BT NICs which
this code supports..
Obtained from: Qualcomm Atheros, Linux ath9k
and the CRC error bits set. The radar payload is correct.
When this happens, the stack doesn't see them PHY error frames and
isn't interpreted as a PHY error. So, no radar detection and no radiotap
PHY error handling.
Now, this may introduce some weird issues if the MAC sends up some other
combination of CRC error + PHY error frames; this commit would break that
and mark them as PHY errors instead of CRC errors.
I may tinker with this a little more to pass radar/early radar/spectral
frames up as PHY errors if the CRC bit is set, to restore the previous
behaviour (where if CRC is set on a PHY error frame, it's marked as a CRC
error rather than PHY error.)
Tested on: AR5416, over the air, to a USRP N200 which is generating a
large number of a variety of radar pulses.
TODO: Test on AR9130, AR9160, AR9280 (and maybe radar pulses on
2GHz on AR9285/AR9287.)
PR: kern/169362
* Add an OS_A_REG_WRITE() routine - analog writes require a 100usec delay
on AR9280 and later, so create a method to do it.
* Use it for the AR9287 analog writes.
* Re-indent and style(9) the code.
This just requires a little HAL change (add a new config parameter) and
some glue in if_ath_pci.c, however I'm leaving this up for someone else
to do.
Obtained from: Qualcomm Atheros
These aren't strictly needed at the moment as we're not doing APSM
and forcing the NIC in and out of network sleep. But, they don't hurt.
Tested:
* AR9280 (mini-PCIe)
Obtained from: Qualcomm Atheros, Linux ath9k
* Now that ah_configPCIE is called for both power on and suspend/resume,
make sure the right bit(s) are cleared and set when suspending and
resuming. Specifically:
+ force disable/enable the PCIe PHY upon suspend/resume;
+ reprogram the PCIe WAR register when resuming and upon power-on.
* Add a recipe which powers down any PCIe PHY hardware inside the AR5416
(which is the PCI variant) to save on power. I have (currently) no way
to test exactly how much power is saved, if any.
Tested on:
* AR5416 cardbus - although unfortunately pccard/cbb/cardbus currently
detaches the NIC upon suspend, I don't think it's a proper test case.
* AR5418 PCIe attached to expresscard - since we're not doing PCIe APSM,
it's also not likely a full/good test case.
In both instances I went through a handful of suspend/resume cycles and
ensured that the STA vap reassociated correctly.
TODO:
* Setup a laptop to simply sit in a suspend/resume loop, making sure that
the NIC always correctly comes back;
* Start doing suspend/resume tests with actual traffic going on in the
background, as I bet this process is all quite racy at the present;
* Test adhoc/hostap mode, just to be completely sure it's working correctly;
* See if I can jury rig an external power source to an AR5416 to test out
whether ah_disablePCIE() works.
Obtained from: Qualcomm Atheros
* Add some other WAR bits (very usefully described too) in preparation for
porting over some suspend/resume fixes from ath9k/Atheros.
Obtained from: Qualcomm Atheros
not to disable the PCIe PHY in prepration for reset.
Extend the enablepci method to have a "poweroff" flag, which if equal
to true means the hardware is about to go to sleep.
* Flesh out the pcie disable method for 11n chips, as they were defaulting
to the AR5212 (empty) PCIe disable method.
* Add accessor macros for the HAL PCIe enable/disable calls.
* Call disable on ath_suspend()
* Call enable on ath_resume()
NOTE:
* This has nothing to do with the NIC sleep/run state - the NIC still
will stay in network-run state rather than supporting network-sleep
state. This is preparation work for supporting correct suspend/resume
WARs for the 11n PCIe NICs.
TODO:
* It may be feasible at this point to keep the chip powered down during
initial probe/attach and only power it up upon the first configure/reset
pass. This however would require correct (for values of "correct")
tracking of the NIC power configuration state from the driver and that
just isn't attempted at the moment.
Tested:
* AR9280 on my Lenovo T60, but with no suspend/resume pass (yet).
in the HAL. That's very memory hungry (32k just for channel statistics)
which would be better served by keeping a summary in the ANI state.
Or, later, keep a survey history in net80211.
So:
* Migrate the ah_chansurvey array to be a single entry, for the current
channel.
* Change the ioctl interface and ANI code to just reference that.
* Clear the ah_chansurvey array during channel reset, both in the AR5212
and AR5416 reset path.
* Always call ar5416GetListenTime()
* Modify ar5416GetListenTime() to:
+ don't update the ANI state if there isn't any ANI state;
+ don't update the channel survey state if there's no active
channel - just to be paranoid
+ copy the channel survey results into the current sample slot
based on the current channel; then increment the sample counter
and sample history counter.
* Modify ar5416GetMIBCyclesPct() to simply return a HAL_SURVEY_SAMPLE,
rather than a set of percentages. The ANI code wasn't using the
percentages anyway.
TODO:
* Create a new function which fetches the survey results periodically
* .. then modify the ANI code to use the pre-fetched values rather than
fetching them again
* Roll the 11n ext busy function from ar5416_misc.c to update all the
counters, then do the result calculation
* .. then, modify the MIB counter routine to correctly fetch a snapshot -
freeze the counters, fetch the values, then reset the counters.
The reference driver has a 3ms delay for the AR9130 but I'm not as yet
sure why. From what I can gather, it's likely waiting for some FIFO
flush to occur.
At some point in the future it may be worthwhile adding a WMAC
FIFO flush here, but that'd require some side-call through to the SoC
DDR flush routines.
Obtained from: Atheros
which will be needed for AR7010 and AR9287 USB access.
The names differ slightly from Linux and Atheros, for the sake of
consistency.
A lot more work is required in order to convert the 11n HAL support to
fully support USB.
at least until I can root cause what's going on.
The only platform I've seen this on is the AR9220 when attached to
the AR71xx CPUs. I get immediate PCIe bus errors and all subsequent
accesses cause further MIPS bus exceptions. I don't have any other
big-endian platforms to test this on.
If I get a chance (or two), I'll try to whack this on a bus analyser
and see exactly what happens.
I'd rather leave this on, especially for slower, embedded platforms.
But the #ifdef hell is something I'm trying to avoid.
Linux ath9k doesn't have this issue as it doesn't try queuing multi-
descriptor frames to the hardware.
Before, I was only setting the first and last descriptor in the final
frame correctly - and that was done by accident. The first descriptor in
the last sub-frame was being correctly updated by ath_tx_setds_11n();
the last descriptor in the last sub-frame was being correctly updated
by ath_buf_set_rate(). But both of those are "incorrect".
The correct behaviour is:
* AR_IsAggr is set for all descriptors for all subframes in an aggregate.
* AR_MoreAggr is set for all descriptors for all non-final sub-frames
in an aggregate.
Ie, all descriptors in the last sub-frame of an aggregate must have this
field set to 0.
I still need to do a couple of extra passes to ensure the pad delimiter
field is being correctly handled in all descriptors in the last sub-frame.
by capabilities.
Add an ar5416SetCapability() function, which contains logic to override
the chainmask and update the relevant stream.
This is designed to be called after the attach function, which presets
the TX/RX chainmask and stream.
TODO: check the chainmask against the hardware chainmask so non-existing
chains aren't enabled.
* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.
* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.
The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.
Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.
* For legacy NICs, the combined RSSI should be used.
For earlier AR5416 NICs, use control chain 0 RSSI rather than combined
RSSI.
For AR5416 > version 2.1, use the combined RSSI again.
* Add in a missing AR5212 HAL method (get11nextbusy) which may be called
by radar code.
This serves no functional change for what's currently in FreeBSD.
to being more generic.
Other embedded SoCs also throw the configuration/PCI register
info into flash.
For now I'm just hard-coding the AR9280 option (for on-board AR9220's on
AP94 and commercial designs (eg D-Link DIR-825.))
TODO:
* Figure out how to support it for all 11n SoC NICs by doing it in
ar5416InitState();
* Don't hard-code the EEPROM size - add another field which is set
by the relevant chip initialisation code.
* 'owl_eep_start_loc' may need to be overridden in some cases to 0x0.
I need to do some further digging.
where they've disabled all the wireless devices/framework.
This is just a build workaround. If you're actively using wireless,
you must still define AH_SUPPORT_AR5416 as I'm not sure what else
will break!
The real solution is to make the module build depend if AH_SUPPORT_AR5416
is defined, as well as make the 11n code in if_ath_tx.c and if_ath_tx_ht.c
completely optional (maybe depend upon ATH_SUPPORT_11N.)
relying on what the register defaults are.
This forces the blink mode to be proportional to the TX and RX frames
which match the RX filter.
This (along with a few tweaks to if_ath_led.c to configure the correct
GPIO pins) allows my DWA-552 AR5416 NIC to blink the LEDs in a useful
fashion, however those LEDs are marked "Link" and "Act(ivity)", which
don't really map well to the "power" / "network" LED interface which
the MAC provides. Some further tinkering is needed to see what other
useful operating modes are possible.
state from correctly updating things.
The reference driver directly enables/disables the LED state as required,
rather than nailing it up like it currently is. That'll have to come
later by adding some further HAL methods.
Obtained from: Atheros
* Bring the AR5416 GPIO mux mask code in line with the code from the
HAL.
* Add HAL_DEBUG_GPIO debugging statements, to track what's going on.
* Add Kiwi GPIO specific changes for reading values back.
Obtained from: Atheros
* As a preparation for AR9287 GPIO support, add in the AR9287 GPIO mask.
* Fix the association mask values; these are post-shift values but were
being shifted in twice. This resulted in some garbage being written
in the wrong place and the link LED (at least on my d-link AR5416
NIC) giving totally incorrect blink patterns.
There's currently no public code which uses this feature and the
current reference driver doesn't enable this feature at all.
It's possible it was used by a previous version of the driver and
that indeed it should return HAL_STATUS; but at this point I'm
happy to require that they complain and submit a patch.
This was found by LLVM compile-time type checking.
Submitted by: dim
and sys/dev/ath/ath_hal/ar5416/ar5416_misc.c:
sys/dev/ath/ath_hal/ar5212/ar5212_misc.c:577:24: warning: implicit conversion from enumeration type 'HAL_STATUS' to different enumeration type 'HAL_BOOL' [-Wconversion]
return HAL_EINVAL;
~~~~~~ ^~~~~~~~~~
and:
sys/dev/ath/ath_hal/ar5416/ar5416_misc.c:164:9: warning: implicit conversion from enumeration type 'HAL_STATUS' to different enumeration type 'HAL_BOOL' [-Wconversion]
return HAL_OK;
~~~~~~ ^~~~~~
In both cases, enums HAL_BOOL and HAL_STATUS are mixed up.
MFC after: 1 week
and sys/dev/ath/ath_hal/ar5211/ar5211_power.c:
sys/dev/ath/ath_hal/ar5210/ar5210_power.c:36:3: warning: signed shift result (0x200000000) requires 35 bits to represent, but 'int' only has 32 bits [-Wshift-overflow]
OS_REG_RMW_FIELD(ah, AR_SCR, AR_SCR_SLE, AR_SCR_SLE_ALLOW);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sys/dev/ath/ath_hal/ah_internal.h:472:42: note: expanded from:
(OS_REG_READ(_a, _r) &~ (_f)) | (((_v) << _f##_S) & (_f)))
^
sys/dev/ath/ah_osdep.h:127:49: note: expanded from:
(bus_space_handle_t)(_ah)->ah_sh, (_reg), (_val))
^~~~
The AR_SCR_SLE_{WAKE,SLP,NORM} values are pre-shifted in ar5210reg.h and
ar5211reg.h, while they should be unshifted, like in ar5212reg.h. Then,
when the OS_REG_RMW_FIELD() macro shifts them again, the values will
overflow, becoming effectively zero.
MFC after: 1 week
attached this way.
The AR5212 based NICs have a variety of RF frontends, so there's a linker set
which the AR5212 attach routine calls. The same framework is used for the
AR5416 and later but as there's a fixed RF frontend for each 11n NIC, it
is just directly attached.
However in the case of compiling a cut down HAL (eg _just_ AR9130 WMAC support),
the linker set ends up being empty and this causes the compile to fail.
So this is just a workaround for that - it means those users who wish an 11n
only HAL can compile the 11n chipsets and RF frontend they need, and just
"ath_ar5212" for the AR5212/AR5416 common code, and it'll just work.
Sponsored by: Hobnob, Inc.
mode configuration registers. This is apparently required for correct
behaviour, but also requires the chip to actually officially support it.
Sponsored by: Hobnob, Inc.
I need to investigate this a little closer, but it seems that in noisy
environments the NF load takes longer than 5 * DELAY(10) and this is
messing up future NF calibrations. (The background: NF calibrations
begin at the value programmed in after the load has completed, so
if this is never loaded in, the NF calibrations only ever start at
the currently calibrated NF value, rather than starting at something
high (say -50.)
More investigation about the effect on 11n RX and calibration results
are needed.
Sponsored by: Hobnob, Inc.
The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.
This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.
Obtained by: Linux, Atheros
to fetch the current channel busy statistics, rather than duplicating
it here.
This forms the (very crude) basis for doing basic channel surveying.
Sponsored by: Hobnob, Inc.
enabled if required by STA operation.
This quietens a lot of OFDM errors seen in hostap mode, where
there are no beacon RSSI levels to tune the dynamic range of the
baseband.
This may reduce reception range at the fringes, but does increase
stability.
Sponsored by: Hobnob, Inc.
The 5ghz hostap mode (where DFS is being done) requires ANI to be disabled
or the radar detection parameters don't work as advertised (as they're based
on signal strength level, and tweaking ANI affects the signal strangth,
dynamic range and power increase the baseband is looking for in order to
detect it as a "signal".)
Obtained from: Linux, Atheros
Sponsored by: Hobnob, Inc.
* If we fall through from an ANI command (eg because it's out of range,
or it's disabled) then fall through to the next ANI command rather then
being stuck there.
* Fix some off-by-one comparisons, meaning the final level in some parameters
were never tweaked.
Obtained from: Atheros
Sponsored by: Hobnob, Inc.
This forces a full reset of the baseband/radio and seems needed to clear
some issues (with Merlin at least) when the baseband gets confused in a
very noisy environment.
Sponsored by: Hobnob, Inc.
RX clear, RX extension clear.
This is useful for estimating channel business.
The same routines should be written for AR5210->AR5212 where appopriate.
Obtained from: Atheros
some unmerged interrupt status debugging code from my branch.
* Add ah_intrstate[8] which will have the record of the last
call to ath_hal_getintr().
* Wrap the KTR code behind ATH_KTR_INTR_DEBUG.
* Add the HAL interrupt debugging behind AH_INTERRUPT_DEBUGGING.
This is only done for the AR5416 and later NICs but it will be
trivial to add to the earlier NICs if required.
Neither are enabled by default, although to minimise HAL binary
API differences, the ah_intrstate[] array is always compiled into
the ath_hal struct.
* preserve AR_TxIntrReq on every descriptor in an aggregate chain,
not just the first descriptor;
* always blank out the descriptor in ar5416ChainTxDesc() when forming
aggregates - the way I'm using this in the 11n branch is to first
chain aggregates together, then use the other HAL calls to fill in
the details.
* Add the TID field in the TX status descriptor;
* Add in the 11n first/middle/last functions for fiddling
with the descriptors. These are from the Linux and the
reference driver, but I'm not (currently) using them.
* Add further AR_ISR_S5 register definitions.
Obtained from: Linux ath9k, Atheros
interfere with traffic, as the NF load can take quite a while and poking the
AGC every 10uS is just a bit silly.
Instead, just leave the baseband NF calibration where it is and just read it
back next time a longcal interval happens.
The final missing bit here is enabling the PCI configuration register
read, but there's currently no glue available for the HAL to read (and
write) PCI configuration space registers.
Obtained from: Atheros
The AR5008/AR9001 series NICs have a bug where BB register reads
will occasionally be corrupted. This could cause issues with things
such as ANI, which adjust operational parameters based on the
BB radio register reads. This was introduced in the AR5008 chip
and fixed with the first released AR9002 series NIC (AR9280v2.)
A followup commit will implement the acutal WAR when reading
BB registers. I'm still not sure how I'll implement it - whether
it should be done in the osdep layer, or whether it should just
live in the AR5416 HAL. Either way, they can use this capability
bit to determine whether to implement the WAR or not.
Thankyou to various sources inside Atheros who have helped me track
down what this particular issue is.
Obtained from: Atheros
Pre-11n devices and AR5416 use AR_PHY(263) for current RX RSSI.
AR9130 and later have a fourth calibration register (for doing
ADC calibration) and thus the register has moved to AR_PHY(271).
This isn't currently used by any of the active code; I'm committing
this for completeness and in case any third party code attempts to
use it for legacy reasons.
* The AR_ISR_RAC interrupt processing method has a subtle bug in all
the MAC revisions (including pre-11n NICs) until AR9300v2.
If you're unlucky, the clear phase clears an update to one of the
secondary registers, which includes TX status.
This shows up as a "watchdog timeout" if you're doing very low levels
of TX traffic. If you're doing a lot of non-11n TX traffic, you'll
end up receiving a TX interrupt from some later traffic anyway.
But when TX'ing 11n aggregation session traffic (which -HEAD isn't yet
doing), you may find that you're only able to TX one frame (due to
BAW restrictions) and this may end up hitting this race condition.
The only solution is to not use RAC and instead use AR_ISR and the
AR_ISR_Sx registers. The bit in AR_ISR which represents the secondary
registers are not cleared; only the AR_ISR_Sx bits are. This way
any updates which occur between the read and subsequent write will
stay asserted and (correctly) trigger a subsequent interrupt.
I've tested this on the AR5416, AR9160, AR9280. I will soon test
the AR9285 and AR9287.
* The AR_ISR TX and RX bits (and all others!) are set regardless of
whether the contents of the AR_IMR register. So if RX mitigation is
enabled, RXOK is going to be set in AR_ISR and it would normally set
HAL_INT_RX.
Fix the code to not set HAL_INT_RX when RXOK is set and RX mitigation
is compiled in. That way the RX path isn't prematurely called.
I would see:
* An interrupt would come in (eg a beacon, or TX completion) where
RXOK was set but RXINTM/RXMINT wasn't;
* ath_rx_proc() be called - completing RX frames;
* RXINTM/RXMINT would then fire;
* ath_rx_proc() would then be called again but find no frames in the
queue.
This fixes the RX mitigation behaviour to not overly call ath_rx_proc().
* Start to flesh out more correct timer interrupt handling - it isn't
kite/merlin specific. It's actually based on whether autosleep support
is enabled or not.
This is sourced from my 11n TX branch and has been tested for a few weeks.
Finally, the interrupt handling change should likely be implemented
for AR5210, AR5211 and AR5212.
There are some timing concerns which I've yet to fully map out.
In any case, there's an existing software driven mitigation method
for TX interrupts and when TX'ing 11n frames, the whole frame itself
generates an interrupt rather then the subframes.
Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.
* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed
This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.
rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
reference driver does clear the async interrupts after each service.
I'll tinker with this in a future commit.
Obtained from: Atheros
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
* Fix SLEEP1/SLEEP2 register definitions; the CAB/Beacon timeout
fields have changed in AR5416 and later
* The TIM_PERIOD and DTIM_PERIOD registers are now microsecond fields,
not TU.
Obtained from: Linux ath9k, Atheros reference
Approved by: re (kib, blanket)
or later. Previous hardware had some as TU, some as 1/8th
TU.
* Modify AR_NEXT_DBA and AR_NEXT_SWBA to use a new macro,
ONE_EIGHTH_TU_TO_USEC(), which converts the 1/8th TU
fields to USEC. This is just cosmetic and matches the
Atheros reference driver.
* Fix AR_NEXT_TBTT, which is USEC, not TU.
Submitted by: paradyse@gmail.com
Approved by: re (kib, blanket)
Remove this debugging, it's not needed anymore and when not enabled,
those variables trigger a compiler warning.
Approved by: re (kib, blanket)
Pointy-hat-to: adrian, for not testing a non-debug compile of this code enough
allows it to be overridden at runtime.
Thus, add a function which updates ah_dfsDomain after a channel set
call to ath_hal_set_channels().
Approved by: re (kib, blanket)
and the Atheros reference code.
The radar detection code needs to know what the current DFS domain is.
Since net80211 doesn't currently know this information, it's extracted
from the HAL regulatory domain information.
The specifics:
* add a new ath_dfs API hook, ath_dfs_init_radar_filters(), which
updates the radar filters whenever the regulatory domain changes.
* add HAL_DFS_DOMAIN which describes the currently configured DFS domain .
* add a new HAL internal variable which tracks the currently configured
HAL DFS domain.
* add a new HAL capability, HAL_CAP_DFS_DMN, which returns the currently
configured HAL DFS domain setting.
* update the HAL DFS domain setting whenever the channel setting is
updated.
Since this isn't currently used by any radar code, these should all
be no-ops for existing users.
Obtained from: Atheros
Submitted by: KBC Networks, sibridge
Approved by: re (kib, blanket)
if 5ghz fast clock is enabled in the current operating mode.
It's slightly dirty, but it's part of the reference HAL and used by
the (currently closed-source) radar event code to map radar pulses
back to microsecond durations.
Obtained from: Atheros
Approved by: re (kib, blanket)
the ar9130 code.
Since at least one kernel config specifies individual ath HAL chips
rather than just "device ath_hal" (arm/AVILA), I'm doing this so people
aren't caught out when they update to -HEAD or 9.0 and discover their
ath setup doesn't compile.
I'll revisit this with a proper fix sometime before 9.0-RELEASE.
Approved by: re (kib, blanket)
Pointed out by: ray@
Pointy hat to: adrian@
systems, in the same way that AR9130 embedded systems work.
This isn't -everything- that is required - the PCI glue still
needs to be taught about the eepromdata hint, along the same
lines as the AHB glue.
Approved by: re (kib, blanket)
This seems to indicate whether to program the NIC for fractional 5ghz
mode (ie, 5mhz spaced channels, rather than 10 or 20mhz spacing) or not.
The default (0) seems to mean "only program fractional mode if needed".
A different value (eg 1) seems to always enable fractional 5ghz mode
regardless of the frequency.
Obtained from: Atheros
Approved by: re (kib)
Calibration/PCI data that's written to flash (rather than EEPROM attached
to the NIC) is typically already in host-endian. The existing checks
end up swapping 16 bit words incorrectly - the correct solution would be
to read the magic value and determine the EEPROM endianness from that.
(This is what Linux does.)
This doesn't completely enable embedded use of the AR9285/AR9287 -
notably, the EEPROM read methods need to be made generic and available
to all EEPROM drivers. I'll worry about that later.
Approved by: re (kib)
* I messed up the order of parameter true/false; oops!
* AR_PHY_RADAR_1 was being written at the wrong place, and was writing
potential garbage to the hardware.
Approved by: re (kib)
* Teach the AR5212/AR5416 ANI code to use the RX filter methods, rather
than calling the RX filter routines directly.
* Make HAL_ANI_PRESENT and HAL_ANI_MODE unconditionally available,
regardless of whether ah_ani_function is masking it.
* (Mostly) fully disable ANI if interference mitigation is disabled.
When disabled, the ANI code doesn't touch any ANI/PHY registers,
leaving them the default value. This is in line with what the
Atheros reference driver does.
* Correctly set the ANI parameters during ANI reset, rather than
when ANI is enabled. In this way, if ANI is disabled or enabled
whilst the NIC is not active (and there's no current channel),
bogus parameters or a NULL pointer deference doesn't occur.
There's still some lingering issues - notably, the MIB events/interrupts
aren't fully disabled, so MIB interrupts still occur. I'll worry about
that later.
Approved by: re (kib)
This in particular fixes radar PHY handling - on the AR5212
NIC, one enables the AR_PHY_ERR_RADAR bit in AR_PHY_ERR;
the AR5416 and later also needs a bit set in AR_RX_FILTER.
A follow-up commit is needed to convert the AR5416 ANI code
to use this particular method, as it's currently using the
AR5212 methods directly.
Obtained from: Atheros
Approved by: re (kib)
the ADC calibrations if the NIC is in 5ghz 11a or 5ghz HT/20 modes.
I've been told that the dual-ADC is only engaged in turbo/40mhz modes.
Since Sowl (AR9160) seems to return valid-looking calibration data
in 5ghz 20MHz modes, I'm only disabling it for Merlin for now.
It may turn out I can disable it for all chipsets and only enable
it for 40MHz modes.
Approved by: re (kib)
It looks like this was mixed up with the AR9285 calibration code.
This code is now more in line with what Linux ath9k and Atheros
reference drivers do.
Obtained from: Atheros
Approved by: re (kib)
tools.
* introduce pe_enabled, which (will) indicate whether the radar
detection stuff is enabled or not. Right now it's incorrectly
set, based on something previously written. I'll sort it out
later.
* Don't set HAL_PHYERR_PARAM_ENABLE in pe_relstep to say whether
radar detection is on.
* Return whether blockradar, fir128 and enmaxrssi is enabled.
* Change some of the phyerr params to be integers rather than
HAL_BOOL so they can be set to the NOPARAM value when the
setup function is called. This is in line with other radar
parameters.
* Add new configuration parameters for fir128, blockradar and
enmaxrssi, rather than defaulting to off, on and on respectively.
Approved by: re (kib)
polluting the AR5416 code with later chipset support.
Note: ar9280InitPLL() supports Merlin (AR9280) and later (AR9285, AR9287.)
Submitted by: ssgriffonuser@gmail.com
Approved by: re (kib)
These should be disabled for the AR5416 in hostap/mesh/ibss mode,
as the AR5416 doesn't have support for radar detection on the
ext channel of a HT40 setup. Later chips do.
Approved by: re (kib)
reference driver.
* Australia should use FCC3_WORLD
* Add some new SKUs; these are just the EEPROM values and haven't been
fully defined yet. As such they won't affect anything.
Obtained from: Atheros
Approved by: re (kib)
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)
The global ath_hal_debug now affects all instances of the HAL.
This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.
rather than global variables.
This specifically allows for debugging to be enabled per-NIC, rather
than globally.
Since the ath driver doesn't know about AH_DEBUG, and to keep the ABI
consistent regardless of whether AH_DEBUG is enabled or not, enable the
debug parameter always but only conditionally compile in the debug
methods if needed.
The ALQ support is currently still global pending some brainstorming.
Submitted by: ssgriffonuser@gmail.com
Reviewed by: adrian, bschmidt
For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.
This information was extracted from the Madwifi DFS branch along with
some local additions.
Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)
For further information, please see:
http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection
This includes references to the relevant patents which describe what
is going on.
Obtained from: Madwifi
Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.
The particulars:
* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.
The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.
Obtained from: Linux, Atheros
This has been disabled until now because there hasn't been any supported
device which has this feature. Since the AR9287 is the first device to
support it, and since now the HAL has functional AR9287+11n support,
flip this on.
AR9287 EEPROM layout.
The AR9287 only supports 2ghz, so I've removed the 5ghz code (but left
the 5ghz edge flags in there for now) and hard-coded the 2ghz-only
path.
Whilst I'm there, fix a typo (ar9285->ar9287.)
This meets basic TX throughput testing - iperf TX tests == 27-28mbit in 11g,
matching the rest of my 11g kit.
I'm assuming for now that the AR9287 is only open-loop TX power control
(as mine is) so I've hard-coded the attach path to fail if the NIC is
not open-loop.
This greatly simplifies the TX calibration path and the amount of code
which needs to be ported over.
This still isn't complete - the rate calculation code still needs to be
ported and it all needs to be glued together.
Obtained from: Linux ath9k
It isn't linked into the build because it's missing the TX power
and PDADC programming code.
This code is mostly based on the ath9k codebase, compared against
the Atheros codebase as appropriate.
What's implemented:
* probe/attach
* EEPROM board value programming
* RX initial calibration
* radio channel programming
* general MAC / baseband setup
* async fifo setup
* open-loop tx power calibration
What's missing before it can be enabled by default:
* TX power / calibration setting code
* closed-loop tx power calibration routines
* TSF2 handling
* generic timer support from ath9k
Obtained from: Atheros, ath9k
values for the commands, compared to the internal command values
(HAL_ANI_CMD.)
My eventual aim is to make the HAL_ANI_CMD internal enum match
the public API and then remove all this messiness.
This now allows HAL_CAP_INTMIT users to use a public HAL_CAP_INTMIT_
enum rather than magic constants.
The only magic constants currently used by if_ath are "enable" and
"present". Some local tools of mine allow for direct, manual fiddling
of the ANI variables and I'll convert these to use the public enum API
before I commit them.
of the ANI statistics and committing some tools which use these.
* Change HAL_ANI_* commands _back_ to be numerical, rather than a
bitmap;
* modify access to the ANI control bitmap to convert a command to
a bitmap;
* Fix the ANI noise immunity fiddling for CCK errors - it wasn't
checking whether noise immunity was disabled or not.
which did AR5212 specific initialisation. This would cause some slight
silliness when enabling/disabling ANI.
Just to be completely correct - and to ensure the phy error mask/RX filter
register isn't incorrectly played with - make the ANI control function a
method, have it set appropriately for AR5212/AR5416, and call that from the
ANI control interface.
This should hopefully make it clearer to developers what is going on
and when TPC is being hacked on, make it obvious why it isn't working for
series 1, 2, 3.
I won't flip on setting TX power for TX series 1, 2, 3 until I've done
some further testing with Kite to ensure it doesn't break anything.
(Before people ask - yes, TPC is only needed for 5ghz regdomains and
yes, Kite is a 2.4ghz only chip, but there are potential use cases
for 2ghz TPC. I just need to sit down and ensure it's supported and
functional.)
control the antenna control bits for the four TX series and the
TPC settings for TX series 1, 2, 3.
The specifics:
* The TPC setting for TX series 0 is handled in ctl0.
* TPC is currently disabled, so the per-packet TX power is
set via the global per-rate TX power register, not per packet.
* The antenna control bits don't matter for AR5416 and later
so they should stay 0 (which they currently do); they may
be set for Kite but as there's no TX diversity supported
at the moment (it requires the NIC to be built with an
external antenna switch, matching how antenna diversity
is done on legacy NICs), so again keep them 0.
This is in preparation for supporting per-rate TPC on the
AR5416 and later. The Kite (and soon to come Kiwi) code
sets ctl8-11 to 0x0, which doesn't have any effect at
the moment. When TPC is enabled it would result in the
second, third and fourth TX series attmpts to be done with
a TX power of 0. This commit doesn't change that; it'll
be followed up with some commits to properly set the TPC
registers appropriately.
the multicast key search support for AR5212, AR5416 and later.
The general HAL routine ath_hal_getcapability() implement checking this
but it's overridden by a check in ar5212_misc:ar5212GetCapability().
This restores the later functionality in case it's found to be broken
in any of the 11n chipsets.
Since the returned NF will be -ve, checking for <= 0 is not good
enough. For now, check whether it equals 0 or -1; a future commit
will tidy this mess up and have it return HAL_BOOL instead.
The eeprom Get method should return HAL_OK if fastclock is enabled in the
EEPROM. It was returning the opposite of what it should have.
Submitted by: Matthew Fleming <mdf356@gmail.com>
The code assumed it could return HAL_OK, HAL_EINVAL and other
HAL_STATUS types; so it shouldn't be declared as returning HAL_BOOL.
This commit was brought to you by the Clang compiler.
Submitted by: Matthew Fleming <mdf356@gmail.com>
I've tested this locally and it does indeed read and attach to an AR9287
EEPROM. But a lot more code needs to be ported over to the HAL before
the AR9287 is functional.
I'm importing this separate from the rest of the codebase (and unlinked from
the build for now) in case someone wishes to begin fiddling with porting
the rest of the code over from Linux ath9k.
Obtained from: Linux ath9k
is totally disabled.
The Atheros HAL code does this for Sowl/Howl but not for Owl (AR5416) where
RIFS is disabled by default.
This seems to quieten the occasional baseband hang I've been seeing with
the AR9160 in STA mode under constant heavy traffic load.
Obtained from: Atheros
for the AR9280 based NICs if it's actually enabled.
Some of the OLC code was erroneously called during setup
and calibration. This may have caused some incorrect behaviour.
table which contains the per-rate target TX power.
This code is shared between the v14 eeprom board setup (AR5416, AR9160,
AR9280) and will also be used by the upcoming Kite (AR9287) support.
* grab the main, alt and selected LNA config
* add some optional / disabled logging code
* add a check to reject packets with an invalid main rssi too,
in case the alt is the active receive chain and main is -ve.
Note: The software-controlled combined diversity code is still disabled.
environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
* Correct some of the silicon revision checks to match what
the Atheros HAL does. (See [1] below.)
* Move the PA cal and init cal method assignment to -after-
the mac version/revision IDs are stored. The AR9285 init
cal was never being called.
* Enable ANI.
Note Kite 1.0 and 1.1 were prototypes that shouldn't be seen
in the wild. Linux ath9k simply removed the prototype code from
their codebase. I'm going to leave it in there for now but
make it conditionally compilable in the future.
Obtained from: Atheros
from Atheros as to what/when this is supposed to be enabled.
Using the default RX fast diversity settings seems to help quite
a bit.
Whilst I'm here, change the prototype to return HAL_BOOL rather than int.
For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.
Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.
Things to todo:
* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.
* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.
For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..
Obtained from: Atheros
The macro which I incorrectly copied into ah_internal.h assumed
that it'd be called with an AR_SREV_MERLIN_20() check to ensure
it was only enabled for Merlin (AR9280) silicon revision 2.0 or
later.
Trouble is, the 5GHz fast clock EEPROM flag is only valid for
EEPROM revision 16 or greater; it's assumed to be enabled
by default for Merlin rev >= 2.0. This meant it'd be incorrectly
set for AR5416 and AR9160 in 5GHz mode.
This would have affected non-default clock timings such as SIFS,
ACK and slot time. The incorrect slot time was very likely wrong
for 5ghz mode.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
for the given channel is available.
It isn't used yet; ar5416GetWirelessModes() needs to be taught
about this rather than assuming HT20/HT40 is available.
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
specific.
The Atheros HAL and FreeBSD HAL share the same capabilities up
until HAL_CAP_11D, where things begin to diverge.
I'll look at tidying these up soon.
Obtained from: Atheros
* Add Howl (ar9130) to the list of chips that have DFS/BB/MAC hangs
* Don't treat unknown BB hangs as fatal; ath9k/Atheros HAL don't
treat it as such.
* Add HAL_DEBUG_DFS to the debug fields in ath_hal/ah_debug.h
The BB hang check simply loops over an observation register checking
for a stuck state engine, but it can happen under high traffic
conditions. Ath9k and the Atheros HAL simply log a debug message and
continue.
Private to FreeBSD:
* Add HAL_DEBUG_HANG to the debug fields
* Change the hang debugging to HAL_DEBUG_HANG rather than HAL_DEBUG_DFS
like in the Atheros HAL.
Obtained from: Atheros
For now, these are equivalent macros. AR_SREV_OWL{X}_OR_LATER
will later change to exclude Howl (AR9130) in line with what
the Atheros HAL does.
This should not functionally change anything.
Obtained from: Atheros
A quick story, which is partially documented in the commit.
The silicon revision in Linux ath9k and the Atheros HAL use an
AR_SREV_REVISION mask of 0x07.
FreeBSD's HAL uses the AR5212 AR_SREV_REVISION mask of 0x0F.
Thus the OWL silicon revisions were coming through as 0xA, 0xB,
0xC, rather than 0x0, 0x1 and 0x2.
My ath9k-sourced AR_SREV_OWL_<X> macros were thus using the wrong
silicon revision values and wouldn't correctly match.
This commit does a few things:
* Change the AR_SREV_OWL_<x> macros to use the AR_SREV_REVISION_OWL_*
values, not AR_XSREV_REVISION_OWL macros;
* Disable AR_XSREV_REVISION_OWL_* values;
* Modify the IS_5416 to properly check the MAC is OWL, rather than
potentially matching on non-OWL revisions (which shouldn't happen
unless there's a silicon revision of higher than 0x9 in a later
chip..)
* Add a couple more macros from the Atheros HAL for compatibility.
The main difference now is that the Atheros HAL defines
AR_SREV_OWL_{20,22}_OR_LATER subtly differently - it fails on all HOWL
silicon. The AR_SREV_5416_*_OR_LATER macros match on the relevant OWL
version -and- all HOWL versions, along with subsequent versions.
A subsequent commit is going to migrate the uses of AR_SREV_OWL_X_OR_LATER
to AR_SREV_5416_X_OR_LATER to match what's going on in the Atheros HAL.
There's only two uses of AR_SREV_OWL_X_OR_LATER which currently don't
apply to FreeBSD but it may do in the future.
Yes, it's all confusing!
Quoting the ath9k commit message:
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Reference: https://patchwork.kernel.org/patch/753862/
Obtained from: Linux ath9k
The checks should function as follows:
* AR_SREV_<silicon> : check macVersion matches that version id
* AR_SREV_<silicon>_<revision> : check macVersion and macRevision match
the version / revision respectively
* AR_SREV_<silicon>_<revision>_OR_LATER: check that
+ if the chip silicon version == macVersion, enforce revision >= macRevision
+ if the chip silicon version > macVersion, allow it.
For example, AR_SREV_MERLIN() only matches AR9280 (any revision),
AR_SREV_MERLIN_10() would only match AR9280 version 1.0, but
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 version >= 2.0 _AND_
any subsequent MAC (So AR9285, AR9287, etc.)
The specific fixes which may impact users:
* if there is Merlin hardware > revision 2.0, it'll now be correctly
matched by AR_SREV_MERLIN_20_OR_LATER() - the older code simply
would match on either Merlin 2.0 or a subsequent MAC (AR9285, AR9287, etc.)
* Kite version 1.1/1.2 should now correctly match. As these macros
are used in the AR9285 reset/attach path, and it's assumed that the
hardware is kite anyway, the behaviour shouldn't change. It'll only
change if these macros are used in other codepaths shared with
older silicon.
Obtained from: Linux ath9k, Atheros
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
Writing the TX power registers is the same between all of these chips
and later NICs (AR9287, AR9271 USB, etc.) so this will reduce code
duplication when those NICs are added to the HAL.
spurious (and fatal) interrupt errors.
One user reported seeing this:
Apr 22 18:04:24 ceres kernel: ar5416GetPendingInterrupts: fatal error,
ISR_RAC 0x0 SYNC_CAUSE 0x2000
SYNC_CAUSE of 0x2000 is AR_INTR_SYNC_LOCAL_TIMEOUT which is a bus timeout;
this shouldn't cause HAL_INT_FATAL to be set.
After checking out ath9k, ath9k_ar9002_hw_get_isr() clears (*masked)
before continuing, regardless of whether any bits in the ISR registers
are set. So if AR_INTR_SYNC_CAUSE is set to something that isn't
treated as fatal, and AR_ISR isn't read or is read and is 0, then
(*masked) wouldn't be cleared. Thus any of the existing bits set
that were passed in would be preserved in the output.
The caller in if_ath - ath_intr() - wasn't setting the masked value
to 0 before calling ath_hal_getisr(), so anything that was present
in that uninitialised variable would be preserved in the case above
of AR_ISR=0, AR_INTR_SYNC_CAUSE != 0; and if the HAL_INT_FATAL bit
was set, a fatal condition would be interpreted and the chip was
reset.
This patch does the following:
* ath_intr() - set masked to 0 before calling ath_hal_getisr();
* ar5416GetPendingInterrupts() - clear (*masked) before processing
continues; so if the interrupt source is AR_INTR_SYNC_CAUSE
and it isn't fatal, the hardware isn't reset via returning
HAL_INT_FATAL.
This doesn't fix any underlying errors which trigger
AR_INTR_SYNC_LOCAL_TIMEOUT - which is a bus timeout of some
sort - so that likely should be further investigated.
It's also marked inactive by the initvals, and enabled after
the baseband/PLL has been configured, but before the RF
registers have been programmed.
The origin and reason for this particular change is currently unknown.
Obtained from: Linux ath9k
Antenna diversity on the >= AR5416 is implemented differently than the
AR5212 and previous chips. So for now, and not to confuse things, just
disable it for now.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
