An error code indicating that the PF rejects the MAC address change
should be returned, in case that the PF has already assigned a MAC
for the VF.
Fixes: af75078fec ("first public release")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch adds new phy type and media type to support
SGMII link for X550, and add ixgbe_setup_sgmii to support
SGMII link setup.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch adds two new VF requests of IXGBE_VF_GET_RETA and
IXGBE_VF_GET_RSS_KEY to the mailbox API.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Previously, a single VLAN header is treated as inner VLAN,
but generally, a single VLAN header is treated as the outer
VLAN header.
The patch fixes the ether type of a single VLAN type, and
enables configuring inner and outer TPID for double VLAN.
Fixes: 19b16e2f64 ("ethdev: add vlan type when setting ether type")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
made second cache line access behavior same as IA
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Reviewed-by: Jianbo Liu <jianbo.liu@linaro.org>
ixgbe PMD RX function(s) misses some packet types that are:
- correctly recognised by the underlying HW.
- marked as supported by ixgbe_dev_supported_ptypes_get().
Fixes: 9586ebd358 ("ixgbe: replace some offload flags with packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Olivier Matz <olivier.matz@6wind.com>
When using kernel PF and DPDK VF, when the PF driver finds the link
state changes, up -> down or down -> up, the driver will send a
message to VF by mailbox. This link state change may be
triggered by PHY disconnection/reconnection, user config change
like *ifconfig down/up* or interface parameter, like MTU change.
This patch enables the support of the mailbox interrupt,
so VF driver can receive the message for link up/down.
After VF receives this message, VF port need to be reset to
recover. This needs to be handled by the application so this patch
allows the app to register a reset callback so it can reset the VF port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
To be consistent with the naming for ARM NEON implementation,
ixgbe_rxtx_vec.c is renamed to ixgbe_rxtx_vec_sse.c.
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Use ARM NEON intrinsic to implement ixgbe vPMD
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[style fixes as highlighted by checkpatch.pl]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
move scalar code which does not use x86 intrinsic functions to new file
"ixgbe_rxtx_vec_common.h", while keeping x86 code in ixgbe_rxtx_vec.c.
This allows the scalar code to to be shared among vector drivers for
different platforms.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the test-pmd
and proc_info applications to use the new xstats API, and removes
deprecated code associated with the old API.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the ixgbe driver
to use the new API that seperates name string and value queries.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The behavior of PKT_RX_VLAN_PKT was not very well defined, resulting in
PMDs not advertising the same flags in similar conditions.
Following discussion in [1], introduce 2 new flags PKT_RX_VLAN_STRIPPED
and PKT_RX_QINQ_STRIPPED that are better defined:
PKT_RX_VLAN_STRIPPED: a vlan has been stripped by the hardware and its
tci is saved in mbuf->vlan_tci. This can only happen if vlan stripping
is enabled in the RX configuration of the PMD.
For now, the old flag PKT_RX_VLAN_PKT is kept but marked as deprecated.
It should be removed from applications and PMDs in a future revision.
This patch also updates the drivers. For PKT_RX_VLAN_PKT:
- e1000, enic, i40e, mlx5, nfp, vmxnet3: done, PKT_RX_VLAN_PKT already
had the same meaning than PKT_RX_VLAN_STRIPPED, minor update is
required.
- fm10k: done, PKT_RX_VLAN_PKT already had the same meaning than
PKT_RX_VLAN_STRIPPED, and vlan stripping is always enabled on fm10k.
- ixgbe: modification done (vector and normal), the old flag was set
when a vlan was recognized, even if vlan stripping was disabled.
- the other drivers do not support vlan stripping.
For PKT_RX_QINQ_PKT, it was only supported on i40e, and the behavior was
already correct, so we can reuse the same bit value for
PKT_RX_QINQ_STRIPPED.
[1] http://dpdk.org/ml/archives/dev/2016-April/037837.html,
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Removed comparison against $CC in Makefiles as
in cross-compiling mode CC can be a different string
instead of string "gcc"
Suggested-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Some architectures (ex: Power8) have a cache line size of 128 bytes,
so the drivers should not expect that prefetching the second part of
the mbuf with rte_prefetch0(&m->cacheline1) is valid.
This commit add helpers that can be used by drivers to prefetch the
rx or tx part of the mbuf, whatever the cache line size.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Many drivers provide their own implementation of rte_mbuf_raw_alloc(),
duplicating the code. Introduce a new public function in rte_mbuf to
allocate a raw mbuf (uninitialized).
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Fix issue reported by Coverity.
Coverity ID 13193: Bad bit shift operation (BAD_SHIFT)
large_shift: In expression 1 << pool, left shifting by more than 31 bits
has undefined behavior. The shift amount, pool, is at least 32.
This patch is a rework of register addr selection logic and mask
computation to made it more readable and avoid bit overflow when 32 bit
value is shifted over its size for pool > 31.
Fixes: fe3a45fd41 ("ixgbe: add VMDq support")
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The masking for the RX/TX enable bit was incorrect in the rx and tx
queue stop functions. Instead of using "& MASK" it used "| MASK" which
would always return true. This error was found by converity scan.
CID 13215 : Wrong operator used (CONSTANT_EXPRESSION_RESULT)
operator_confusion: txdctl | 33554432 is always 1/true regardless of the
values of its operand. This occurs as the logical second operand of
'&&'.
CID 13216 : Wrong operator used (CONSTANT_EXPRESSION_RESULT)
operator_confusion: rxdctl | 33554432 is always 1/true regardless of the
values of its operand. This occurs as the logical second operand of
'&&'.
Coverity issue: 13215
Coverity issue: 13216
Fixes: 029fd06d40 ("ixgbe: queue start and stop")
Signed-off-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Run ixgbe driver through checkpatch and fix the issues highlighted
Fix line spacing, some bad indentation, and in a couple
of cases use short circuit (already there) return to lessen indentation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Applied with four additional fixes for issues highlighted by checkpatch
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Some statistics were deprecated since release 2.1 (49f386542a).
The last deprecated counter to be used was imcasts.
The VF loopback statistics are also removed as they are used only
in igb and duplicated in extended statistics.
The new counters should be added to extended statistics.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Remy Horton <remy.horton@intel.com>
VxLAN & NVGRE are supported by x550. As we know HW can parse
the packet and tell SW the type info. For VxLAN & NVGRE packets
there's some change. HW will not tell SW the info of the outer
header but the inner header instead. But we always take the
info as it's for the outer header. So the packet type info is
not right when x550 receives VxLAN & NVGRE packets.
As x550 only supports IPv4 VxLAN & NVGRE packets, we can tell
the outer header of VxLAN is IPv4 + UDP, and the outer header
of NVGRE is IPv4 only. What we don't know is if there's
optional field in the outer IPv4 header.
This patch implement the support of packet type for VxLAN &
NVGRE. And it fixes the wrong packet type issue either.
BTW:
It doesn't fix any existing commit as although it resolve an
issue it's more like a new feature but not a fix.
Reported-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch redesigns the API to set the link speed/s configuration
of an ethernet port. Specifically:
- it allows to define a set of advertised speeds for
auto-negociation.
- it allows to disable link auto-negociation (single fixed speed).
- default: auto-negociate all supported speeds.
A flag autoneg in struct rte_eth_link indicates if link speed was a
result of auto-negociation or was fixed by configuration.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Tested-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Beilei Xing <beilei.xing@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The speed capabilities of a device can be retrieved with
rte_eth_dev_info_get().
The new field speed_capa is initialized in the drivers without
taking care of device characteristics in this patch.
When the capabilities of a driver are accurate, the table in
overview.rst must be filled.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
The speed numbers ETH_LINK_SPEED_ are renamed ETH_SPEED_NUM_.
The prefix ETH_LINK_SPEED_ is kept for AUTONEG and will be used
for bit flags in next patch.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Some duplex values are replaced from 0 to half-duplex when link is down.
Some drivers are still using their own constants for duplex modes.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Define and use ETH_LINK_UP and ETH_LINK_DOWN where appropriate.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Silence a compiler warning that this variable may be used uninitialized.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tell the compiler to use an unsigned constant for the config shifts.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The lower 16 bits of EICR register are used for queue interrupts,
dpdk framework take over the first bit for other interrupts like
LSC, so there're only 15 bits left for queue interrupts mapping.
This patch adds a check for the num of interrupt queues at
dev_start.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When starting testpmd with multiple queues on a ixgbe VF
port, it failed with this printing, "nb_rxq(4) is greater
than max_rx_queues(1)".
The root cause is the VF doesn't get the right max rx queue
number from PF and it uses the default value 1.
VF max rx queue number is set by PF through mailbox messages.
The message for this setting only supports version 1.1. As
message version is updated to 1.2, VF cannot parse the rx queue
number setting message correctly.
This patch raise a specific base code update for this issue.
Fixes: 72dec9e37a ("ixgbe: support multicast promiscuous mode on VF")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
l2 tunnel and e-tag are not supported on the new x550em_a NICs, due
to missing checks for that mac type in the code.
This patch adds in the necessary conditional checks to enable the features
for x550em_a.
Fixes: 22e77d4501 ("ixgbe: support L2 tunnel operations")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
An issue is found on x550em NICs: ieee1588 is not working, the time is
always reported as 0.
The root cause is that the timer is only supported by the driver for x550,
switch statement entries are missing for x550em_x and x550em_a. This patch
adds those missing entries.
Fixes: a7740dc130 ("ixgbe: support new devices and MAC types")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
icc (icc (ICC) 16.0.1 20151021) is generating following compile error:
CC ixgbe_rxtx.o
.../drivers/net/ixgbe/ixgbe_rxtx.c(153): error #3656: variable
"free" may be used before its value is set
(nb_free > 0 && m->pool != free[0]->pool)) {
^
Indeed this is a false positive and code is correct.
"nb_free" check prevents the free[] access before its value set.
Disabling this icc warning (#3656) for file ixgbe_rxtx.c.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Ixgbe HW supports 128 TX queues. However, the full 128 queues are only
available in VT and DCB mode. In normal default "none" mode (VT/DCB off)
the maximum number of available queues is only 64.
The driver doesn't check the mode when reporting the available
number of queues, allowing more that 64 queues to be used in all cases.
If a queue no. >=64 is used in default mode, the TX packets will be dropped
silently.
This change adds a check to forbid using a queue number larger than 64
during device configuration (in default mode), so that the problem is
reported as early as possible.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Internal variable containing the number of TX queues for a device,
was being incorrectly assigned the number of RX queues, instead of TX.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
There's an issue reported. In the scenario DPDK PF + DPDK VF,
if the VF port is closed, PF port cannot receive packets.
I found at that time the promicuous mode is disabled on the PF
port. But it should be enabled.
When VF port is closed, it will send a message to its PF port to
reset it. During this, PF port will also reset its own
promicuous mode. Which promiscuous mode should be set depends on
the parameter stored in the device data. In the function
set_rx_mode, the pointer of device data points to the wrong
address. So, the promiscuous mode is wrong.
Fixes: 00e30184da ("ixgbe: add PF support")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Reported-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Current vector RX can't always set the packet_type properly.
To be more specific:
a) it never sets RTE_PTYPE_L2_ETHER
b) it doesn't handle tunnel ipv4/ipv6 case correctly.
c) it doesn't check is IXGBE_RXDADV_PKTTYPE_ETQF set or not.
While a) is pretty easy to fix, b) and c) are not that straightforward
in terms of SIMD ops (specially b).
So far I wasn't able to make vRX support packet_type properly without
noticeable performance loss.
So for now, just remove that functionality from vector RX and
update dev_supported_ptypes_get().
Fixes: 3962541758 ("mbuf: redefine packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
For x550 device, the reta table has 512 entries, but in function
ixgbe_dev_rss_reta_query and ixgbe_dev_rss_reta_update we use an
"uint8_t i" to traverse the entries, this will lead the function
to an endless loop.
This patch changes the data type from uint8_t to uint16_t to fix
the issue.
Fixes: 4bee94a6c2 ("ixgbe: support 512 RSS entries on x550")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add a new API rte_eth_dev_get_supported_ptypes to query what packet types
can be filled by a given device. The device should be already started or
its PMD RX burst function already decided, since the packet types supported
may vary depending on RX function.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Comment for "ierrors" counter says that it counts erroneous received
packets. But for some reason "imissed" counter is added to "ierrors"
counter in most drivers.
It is a mistake, because missed packets are obviously not received.
This patch fixes it.
Fixes: 70bdb18657 ("ethdev: add Rx error counters for missed, badcrc and badlen packets")
Fixes: 6bfe648406 ("i40e: add Rx error statistics")
Fixes: 856505d303 ("cxgbe: add port statistics")
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The multi queue mode ETH_MQ_RX_VMDQ_DCB_RSS is not supported in
ixgbe driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Call the ixgbevf_remove_mac_addr() function in the ixgbevf_dev_close()
function to ensure that the VF traffic goes to the PF after stop,
close and detach of the VF.
Fixes: af75078fec ("first public release")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add the nb_rx_q and nb_tx_q values to the error message
to give details about the error.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Releasing the rx and tx queues is already done in ixgbe_dev_close()
so it does not need to be done in eth_ixgbevf_dev_uninit().
Fixes: 2866c5f1b8 ("ixgbe: support port hotplug")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
For the secondary process of DPDK to initialize ixgbevf, it will always
use the simple RX function or LRO RX function, and this behavior is not
the same RX/TX function selection logic as it is for the primary process.
Use the ixgbe_set_tx_function and ixgbe_set_rx_function to select the
RX/TX function when secondary process calls the init function for eth dev.
Fixes: 9d8a92628f ("ixgbe: remove simple scalar scattered Rx method")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Normally the auto-negotiation is supported by FW. SW need not care about
that. But on x550em_x, FW doesn't support auto-neg. As the x550em_x ports
are 10G, if we connect the port will a peer which is 1G, the link will
always be down.
We need support auto-neg by SW to avoid this link down issue. As we already
have the code to handle the link speed setting, what we need is a trigger.
When the advertised link speed changes, a PHY interruption will be
triggered. So, we should handle this interrupt and call ixgbe_handle_lasi
to set the link speed correctly.
Please be aware it's working when auto-neg is on. If the auto-neg of the
peer port is turned off and its speed is indicated manually, we should also
set the speed of our own port manually.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Add multicast promiscuous mode support on ixgbe VF driver.
Please note if we want to use this promiscuous mode, we need both PF
and VF driver to support it. The reason is this VF feature is
configged on PF.
If use kernel PF driver + dpdk VF driver, make sure kernel PF driver
support VF multicast promiscuous mode. If use dpdk PF + dpdk VF,
better make sure PF driver is the same version as VF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
It's more valuable to abstract the link read/write interface. As such,
change the following method names, and add them to a new link info
structure:
read_i2c_combined => read_link
read_i2c_combined_unlocked => read_link_unlocked
write_i2c_combined => write_link
write_i2c_combined_unlocked => write_link_unlocked
This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access.
Initially the structure is just method pointers and a bus
address.
Two functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The MDIO clock speed must be reconfigured after the MAC reset.
The MDIO clock speed becomes invalid, therefore the driver reads
invalid PHY register values. The driver now set the MDIO clock
speed prior to initializing PHY ops and again after the MAC reset.
As now the MDIO speed gets set in more than one place, make a
function for it so it will always be done correctly.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Do not set FDIRCTRL.DROP_NO_MATCH in ixgbe_init_fdir_perfect_82599(),
this bit is already set in ixgbe_set_fdir_drop_queue_82599() which
makes more sense for drivers that call that function.
This resolves an issue where packets were being dropped when switching
to perfect filters mode.
Setting this bit makes no sense in perfect filters mode for the
driver as we do not want to route all packets that don't match an FDIR
rule to a single queue and instead fall back to RSS.
Drivers that need this bit set can call ixgbe_set_fdir_drop_queue_82599()
and the ones that don't, can preserve the old behavior.
Fixes: 2241ce2816 ("ixgbe/base: add flow director drop queue")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The X550EM_a device provides the MAC_SGMII_BUSY register to
indicate when slow SGMII register writes complete. Add
definitions for the register. No definitions are provided for
the individual bits under the theory that it is better to wait
for everything to complete when needed rather than try to map
out which reads need to wait for which writes. So we should wait
when anything is marked as "busy".
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Instead of not defining the callback for set_phy_power when
manageability is enabled, put the check in the set_phy_power
function so that only turning the power off is conditional on
management, but not turning the PHY on.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch resolves an issue where VF mac address is zeroed out
in cases where the VF driver is loaded while the PF interface
is down.
The solution is to only set it when we get an ACK from the PF.
Fixes: 6202266e56 ("ixgbe/base: vf changes")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Only x550em_x V1 was supported before. Now V2 is supported.
A mask for V1 and V2 is defined and used to support both.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add new X550EM_a devices and their mac types, X550EM_a
and X550EM_a_vf.
Update the code to use the new devices and mac types.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently, ixgbe vf and pf will disable interrupt twice in
stop stage and uninit stage. It will cause an error:
testpmd> quit
Shutting down port 0...
Stopping ports...
Done
Closing ports...
EAL: Error disabling MSI-X interrupts for fd 26
Done
because the interrupt has already been disabled in stop stage.
Since it is enabled in init stage, better remove from
stop stage.
Fixes: 0eb609239e ("ixgbe: enable Rx queue interrupts for PF and VF")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The freeing of mbuf's in ixgbe is one of the observable hot spots
under load. Optimize it by doing bulk free of mbufs using code similar
to i40e and fm10k.
Drop the no longer needed micro-optimization for the no refcount flag.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch add VxLAN & NVGRE TX checksum off-load. When the flag of
outer IP header checksum offload is set, we'll set the context
descriptor to enable this checksum off-load.
Also update release notes for VxLAN & NVGRE checksum off-load support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
X550 will do VxLAN & NVGRE RX checksum off-load automatically.
This patch exposes the result of the checksum off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add UDP tunnel port add/del support on ixgbe. Now only
support VxLAN port configuration.
Although according to the specification the VxLAN port has
a default value 4789, it can be changed. We support VxLAN
port configuration to meet the change.
Note, the default value of VxLAN port in ixgbe NICs is 0. So
please set it when using VxLAN off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add support of l2 tunnel configuration and operations.
1, Support modifying ether type of a type of l2 tunnel.
2, Support enabling and disabling the support of a type of l2 tunnel.
3, Support enabling/disabling l2 tunnel tag insertion/stripping.
4, Support enabling/disabling l2 tunnel packets forwarding.
5, Support adding/deleting forwarding rules for l2 tunnel packets.
Only support E-tag now.
Also update the release note.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
On X550, as required by datasheet, E-tag packets are not expected
when double VLAN are used. So modify the register PFVTCTL after
enabling double VLAN to select pool by MAC but not MAC or E-tag.
An introduction of E-tag:
It's defined in IEEE802.1br. Please reference this website,
http://www.ieee802.org/1/pages/802.1br.html.
A brief description.
E-tag means external tag, and it's a kind of l2 tunnel. It means a
tag will be inserted in the l2 header. Like below,
|31 24|23 16|15 8|7 0|
0| Destination MAC address |
4| Dest MAC address(cont.) | Src MAC address |
8| Source MAC address(cont.) |
12| E-tag Etherenet type (0x893f) | E-tag header |
16| E-tag header(cont.) |
20| VLAN Ethertype(optional) | VLAN header(optional) |
24| Original type | ...... |
...| ...... |
The E-tag format is like below,
|0 15|16 18|19 |20 31|
| Ethertype - 0x893f | E-PCP |DEI| Ingress E-CID_base |
|32 33|34 35|36 47|48 55 |56 63|
| RSV | GRP |E-CID_base|Ingress_E-CID_ext| E-CID_ext |
The Ingess_E-CID_ext and E-CID_ext are always zero for endpoints
and are effectively reserved.
The more details of E-tag is in IEEE 802.1BR. 802.1BR is used to
replace 802.1Qbh. 802.1BR is a standard for Bridge Port Extension.
It specifies the operation of Bridge Port Extenders, including
management, protocols, and algorithms. Bridge Port Extenders
operate in support of the MAC Service by Extended Bridges.
The E-tag is added to l2 header to identify the VM channel and
the virtual port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Fixed issue of byte order in ethdev library that the structure
for setting fdir's mask and flow entry is inconsist and made
inputs of mask be in big endian.
Fixes: 2d4c1a9ea2 ("ethdev: add new flow director masks")
Fixes: 76c6f89e80 ("ixgbe: support new flow director masks")
Reported-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Macros RTE_MBUF_DATA_DMA_ADDR and RTE_MBUF_DATA_DMA_ADDR_DEFAULT
are defined in each PMD driver file. Convert macros to inline
functions and move them to common lib/librte_mbuf/rte_mbuf.h file.
PMD drivers include rte_mbuf.h file directly/indirectly hence no
additioanl header file inclusion is necessary.
Signed-off-by: Ravi Kerur <rkerur@gmail.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
fix the error reported by checkpatch:
"ERROR: return is not a function, parentheses are not required"
remove parentheses in return like:
"return (logical expressions)"
remove parentheses in return a function like:
"return (rte_mempool_lookup(...))"
Fixes: 6307b909b8 ("lib: remove extra parenthesis after return")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
The x550 MDIO clock speed must be configured prior to first MDIO read or
write. The default MDIO clock speed is not valid, therefore the driver
is configuring a valid speed prior to reading the copper PHY device id.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_X550em. Since
this function is meant to initialize function pointers for detected PHY
type. Internal PHY reset was moved to ixgbe_setup_internal_phy_t_x550em
which will now detect which mode does internal PHY work in, and setup it
as required.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
KR auto-neg mode is what we will be using going forward. The SW
interface for this mode is different than what was used for iXFI.
While debugging, it was determined that the ucode diagnostic was
no longer needed. This code has been removed to simplify the init
flow.
A subtle semaphore error in the CS4227 reset flow was fixed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch changes code to use registers offsets stored in mvals table
instead of values defined statically.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds ixgbe_set_fdir_drop_queue_82599 for enabling and
setting flow director drop queue, and adds sets drop no match in
ixgbe_init_fdir_perfect_82599 for x550.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Waiting for FDIRCMD completion is an expensive thing to do in the
transmit hot path. This wait was added to catch problems with perfect
filter rules, and, at least in the Linux driver, there is no error
check anyway, so there is no point to adding the delay. So do not wait
for completion. Change the return of the function to void, since it has
no meaningful return value.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch adds the flow control ethertype to the defines for the
ETQF filter list. This only adds the define. Each driver
can add this ethertype to the filter. This is needed to prevent
denial of service by malicious VFs sending out flow control
packets.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently credit_refill and credit_max could be zero for a TC and that
is causing Tx hang for CEE mode configuration, so to fix that have at
min credit assigned to a TC and that is as what IEEE mode already does.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This counter was left unmodified. Restore it in ixgbe_dev_stats_get.
The ierrors counter still includes imissed for ixgbe. This behaviour is
not consistent amongst all drivers. Another patch may be needed to unify
the meaning of the ierrors counter.
Fixes: 5e50ad1c1b ("ixgbe: add specific stats")
Signed-off-by: Robin Jarry <robin.jarry@6wind.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
This patch fixes tx byte statistics when transmitting packets
with link down.
Previously, the counter would decrement 4 bytes for each packet that
was transmitted with link down, causing the uint64 to wrap around.
Fixes: c03fcee9ab ("ixgbe: remove CRC size from byte counters")
Reported-by: Michael Qiu <michael.qiu@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
There is a compilation issue with some compilers.
In i686 platform, long is 32bit, so XXX_CYCLECOUNTER_MASK
need define as 'ULL'
Fixes: 9c857bf6be ("igb: support ieee1588 functions for device time")
Fixes: 1c4445e1f2 ("ixgbe: support ieee1588 functions for device time")
Fixes: f3a4e40eca ("i40e: support ieee1588 functions for device time")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
The vector number may change during 'dev_start'. Before enabling a new vector mapping,
it's necessary to disable/unmap the previous setting.
Fixes: 7ab8500037 ("ixgbe: fix VF start with PF stopped")
Reported-by: Yong Liu <yong.liu@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes the crc bytes from byte counter statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
This patch refactors the queue handling. Generic queue stats are
handled by rte_eth_xstats_get() and the ixgbe_xstats_get() exposes
only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
One of the ways to reproduce the issue:
testpmd <EAL-OPTIONS> -- -i --txqflags=0
testpmd> set fwd txonly
testpmd> set txpkts 64,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4
testpmd> set txsplit rand
testpmd> start
After some time TX on ixgbe queue will hang,
and all packet transmission on that queue will stop.
This bug was first reported and investigated by
Vlad Zolotarov <vladz@cloudius-systems.com>:
"We can reproduce this issue when stressed the xmit path with a lot of highly
fragmented TCP frames (packets with up to 33 fragments with non-headers
fragments as small as 4 bytes) with all offload features enabled."
The root cause is that ixgbe_xmit_pkts() in some cases violates the HW rule
that the distance between TDs with RS bit set should not exceed 40 TDs.
>From the latest 82599 spec update:
"When WTHRESH is set to zero, the software device driver should set the RS bit
in the Tx descriptors with the EOP bit set and at least once in the 40
descriptors."
The fix is to make sure that the distance between TDs with RS bit set
would never exceed HW limit.
As part of that fix, tx_rs_thresh for ixgbe PMD is not allowed to be greater
then to 32 to comply with HW restrictions.
With that fix slight slowdown for the full-featured ixgbe TX path
might be observed (from our testing - up to 4%).
ixgbe simple TX path is unaffected by that patch.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch removes l3_l4_xsum_errors from rx errors.
The reason to remove it is that UDP packets have an optional checksum, and
when not calculated the checksum field should be set to zero. When the
checksum is not calculated (zero-ed out), the hardware still counts a valid
UDP packet as an l3_l4_xsum_error.
This hardware issue is documented in 82599 errata, titled:
"Integrity Error Reported for IPv4/UDP Packets with Zero Checksum"
The solution is to remove l3_l4_xsum_errors from rx_errors, as discussed on
http://thread.gmane.org/gmane.comp.networking.dpdk.devel/25590/
Fixes: f6bf669b99 ("ixgbe: account more Rx errors")
Suggested-by: Martin Weiser <martin.weiser@allegro-packets.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Following the same approach taken with dev_started field
in rte_eth_dev_data structure, this patch adds two new fields
in it, rx_queue_state and tx_queue_state arrays, which track
which queues have been started and which not.
This is important to avoid trying to start/stop twice a queue,
which will result in undefined behaviour
(which may cause RX/TX disruption).
Mind that only the PMDs which have queue_start/stop functions
have been changed to update this field, as the functions will
check the queue state before switching it.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
As ixgbe vf doesn't support lsc, the patch removes those unused code.
In addition, it does some tiny cleanup.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
When ixgbe runs as a PF, mbox interrupt is prerequisite to make VF
start normally.
And PF sometimes won't 'dev_start', so the mbox interrupt register
during 'dev_init' is required.
The patch rolls back the interrupt register for mbox,lsc to the 'dev_init'.
As UIO doesn't support multiple vector, mbox has to occupy the only one.
It adds condition check on 'dev_start', rxq interrupt is not allowed
when PF running in IOV mode via UIO.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
According to the VFIO interrupt mapping, the interrupt vector id
for rxq starts from RX_VEC_START.
It doesn't impact the UIO cases.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Use new function rte_eth_copy_pci_info.
Copy device info for the following pdevs:
bnx2x
cxgbe
e1000
enic
fm10k
i40e
ixgbe
mlx4
mlx5
virtio
vmxnet3
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
According to Table 7-38: Valid Fields by Offload Option
of Intel ® 82599 10 GbE Controller Datasheet,
L4LEN field is not needed for L4 XSUM computation by the hardware.
So remove l4_len from tx_offload_mask in ixgbe_set_xmit_ctx
function used to build the context transmitted to the hardware.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch removes the mac local fault count and
mac remote fault count from rx errors. The mac
fault count registers count faults, not packets,
and hence should not be added to packet counters.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Add xstats() functions and stat strings as necessary to ixgbevf PMD.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
Added and updated statistic strings as used by xstats_get(),
exposed extended queue statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This patch adds one new API to get dcb related info.
rte_eth_dev_get_dcb_info
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch enables DCB+RSS multi-queue mode, and also fix some coding
style.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Different NIC has its specific constraint on the multi-queue
configuration, so move the checking from ethdev lib to drivers.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Implement the new CLIs for fdir mac vlan and tunnel modes, including
flow_director_filter and flow_director_mask. Set the mask of fdir.
Add, delete or update the entities of filter.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch implements the VF RSS reta/hash query and update function
on 10G NICs. But the update function is only provided for x550. Because
the other NICs don't have the separate registers for VF, we don't want
to let a VF NIC change the shared RSS reta/hash registers. It may cause
PF and other VF NICs' behavior change without being noticed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
On x550, there're separate registers provided for VF RSS while on the other
10G NICs, for example, 82599, VF and PF share the same registers.
This patch lets x550 use the VF specific registers when doing RSS configuration
on VF. The behavior of other 10G NICs doesn't change.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Comparing with the older NICs, x550's RSS redirection table is enlarged to 512
entries. As the original code is for the NICs which have a 128 entries RSS table,
it means only part of the RSS table is set on x550. So, RSS cannot work as
expected on x550, it doesn't redirect the packets evenly.
This patch configs the entries beyond 128 on x550 to let RSS work well, and also
update the query and update functions to support 512 entries.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch will drop flow control frames from being transmitted
from VSIs.
With this patch in place a malicious VF cannot send flow control
or PFC packets out on the wire.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
At the original point the rx_pkts[pos( + n)] pointers are not initialized,
so the code is prefetching random data.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Incorrect operator in ixgbe_get_eeprom & ixgbe_set_eeprom prevents
last byte of EEPROM being read/written, and hence cannot be dumped
or updated in entirity using these functions.
Fixes: 0198848a47 ("ixgbe: add access to specific device info")
Signed-off-by: Remy Horton <remy.horton@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch adds the mspdc (MAC Short Packet Discard Count)
to the total rx errors, as discussed on the dev@dpdk mailing
list: http://comments.gmane.org/gmane.comp.networking.dpdk.devel/23717
Suggested-by: Igor Ryzhov <iryzhov@arccn.ru>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Remove receive jabber count (rjc) from ierrors count as the
register overlaps with the CRC error register, previously
causing some packets to be counted twice.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Ixgbe based 82598 and 82599 have different priority receive link-on
register addresses. This is solved in base/ by providing in the
PXONRXC and PXONXCNT as separate macros. This patch ensures the
correct address is read, avoiding reading garbage values.
Also PXON2OFFCNT doesn't exist in 82598, so it is not read for
that MAC.
This issue has existed since the drivers were imported into DPDK,
but was not easily discoverable as xstats were not available.
Tested using testpmd> show port xstats all
Fixes: af75078fec ("first public release")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When setting TSO on VF ixgbe NICs, for example, 82599, x550, the
prompt that TSO is not supported will be printed. But TSO is
supported by VF ixgbe NICs.
We should add TSO to the capability flag, so, we will not see the
wrong prompt.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
On receive side, the burst size now floor aligns to RTE_IXGBE_DESCS_PER_LOOP
power of 2. According to this rule, the burst size less than 4 still won't
receive anything.
(Before this change, the burst size less than 32 can't receive anything.)
_recv_*_pkts_vec returns no more than 32(RTE_IXGBE_RXQ_REARM_THRESH) packets.
On transmit side, the max burst size no longer bind with a constant, however
it still requires to check the cross tx_rs_thresh violation.
There's no obvious performance drop found on both recv_pkts_vec
and recv_scattered_pkts_vec on burst size 32.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Reviewed-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
There's a DCB issue on x550. For 8 TCs, if a packet with user priority 6
or 7 is injected to the NIC, then the NIC will put 3 packets into the
queue. There's also a similar issue for 4 TCs.
The root cause is RXPBSIZE is not right. RXPBSIZE of x550 is 384. It's
different from other 10G NICs. We need to set the RXPBSIZE according to
the NIC type.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The extended unified packet type is now part of the standard ABI.
As mbuf struct is changed, the mbuf library version is incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
The Rx interrupt feature is now part of the standard ABI.
Because of changes in rte_intr_handle and struct rte_eth_conf,
the eal and ethdev library versions are incremented.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
This patch adds a note to the README files in the
drivers/net/pmd/base dirs to highlight that the code should not
be modifed by the user apart from the pmd_osdep.[ch] files.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Niantic HW expects Header Buffer Address in the RXD to be word aligned.
So, if mbuf's buf_physaddr is not word aligned then
RX path will not work properly.
Right now, in ixgbe PMD we always setup Packet Buffer Address(PBA) and
Header Buffer Address (HBA) to the same value:
buf_physaddr + RTE_PKTMBUF_HEADROOM.
As ixgbe PMD doesn't support split header feature anyway,
the issue can be fixed just by always setting HBA in the RXD to zero.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch adds management of PKT_RX_FDIR and PKT_RX_RSS_HASH ol_flags in
vPMD for unified packet type as well as for 16 bit field packet_type when
RTE_NEXT_ABI is not defined.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Some drivers was not following DPDK convention and
was leaving logging always in even if LOG_LEVEL was configured
to disable debug logs.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[Thomas: apply same fix to i40e, fm10k and bnx2x]
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Customers often screen off info level messages, so raise log
level of significant events.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
All the debug chatter messages in the system log causes
complaints from users. Change the INFO messages to DEBUG
for normal startup kind of stuff.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
oerrors was txdgpc - hw_stats->gptc,
txdgpc is the number of packets DMA'ed by the host
and was being reset on every call to read stats so it could be < gptc.
Because we currently have no way to add txdgpc to struct hw_stats so
that we can maintain a persistent value per port oerrors has now been
set to 0. References to txdgpc is now removed as we don't use it. This
patch also removes rxnfgpc as it's not used anywhere.
Fixes: afebc86be1 ("ixgbe: refactor stats register reads")
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
For 2.1 release, in attempt to minimize number of RX routines to support,
ixgbe scatter and ixgbe LRO RX routines were merged into one
that can handle both cases.
Though I completely missed the fact, that while LRO could only be used
when HW CRC strip is enabled, scatter RX should work for both cases
(HW CRC strip on/off).
That patch restores missed functionality.
Fixes: 9d8a92628f ("ixgbe: remove simple scalar scattered Rx method")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
1. cpu use data owned by ixgbe must use rte_le_to_cpu_xx(...)
2. cpu fill data to ixgbe must use rte_cpu_to_le_xx(...)
3. checking pci status with converted constant
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch does below things for ixgbe PF and VF:
- Setup NIC to generate MSI-X interrupts
- Set the IVAR register to map interrupt causes to vectors
- Implement interrupt enable/disable functions
Signed-off-by: Danny Zhou <danny.zhou@intel.com>
Signed-off-by: Yong Liu <yong.liu@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
As Steve pointed out, the commit 11b220c649 ("ixgbe: fix release queue mbufs")
is not complete.
As at queue stop we don't reset vector related rx queue fields to their
initial values.
Fixes: c95584dc2b ("ixgbe: new vectorized functions for Rx/Tx")
Reported-by: Cunming Liang <cunming.liang@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The check for split packets to be reassembled in the vector ixgbe PMD
was incorrectly only checking the first 16 elements of the array instead
of all 32. This is fixed by changing the uint32_t values to be uint64_t
instead.
Fixes: cf4b4708a8 ("ixgbe: improve slow-path perf with vector scattered Rx")
Reported-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC config option is not really
necessary, as bulk alloc rx function can be used anyway, as long as the
necessary conditions are satisfied, which are checked already
in the library.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The vector/SSE pmd used a different element type for the tx queue sw_ring
entries. This led to lots of typecasts in the code which required specific
use of bracketing, leading to subtle errors.
For example, in the original code:
txe = (struct ixgbe_tx_entry_v *)&txq->sw_ring[i];
instead needs to be written as:
txe = &((struct ixgbe_tx_entry_v *)txq->sw_ring)[i];
We can eliminate this problem, by having two software ring pointers in the
structure for the two different element types.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The function inside the vector/SSE poll-mode driver for releasing
the mbufs on the TX queues had the same name as another function
inside the regular PMD. To keep consistency and avoid confusion,
rename the vector PMD version to have a "_vec" suffix.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The calculations of what mbufs were valid in the RX and TX queues were
incorrect when freeing the mbufs for the vector PMD. This led to crashes
due to invalid reference counts when mbuf debugging was turned on, and
possibly other more subtle problems (such as mbufs being freed when in use)
in other cases.
To fix this, the following changes were made:
* correct counts and post-loop values in the TX release function for the
vector code.
* create a new separate RX release function for the RX vector code, since the
tracking of what mbufs are valid or not is different for that code path
Fixes: c95584dc2b ("ixgbe: new vectorized functions for Rx/Tx")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The bug fix was incorrect as it did not take account of the fact that
the mbufs that were previously freed may have since be re-allocated.
Reverts: b35d0d80f0 ("ixgbe: check mbuf refcnt when clearing a ring")
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The two fields for vector RX rearming in the rx queue structure were
incorrectly labelled. Switching the comments on each around makes things
clearer.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Bug fix to remove (rxnfgpc - hw_stats->gprc) which does not account
for phy errors.
hw_stats->gprc is the Number of good (non-erred) Rx packets (from the
network) that pass L2 filtering and has a legal length as defined by
LongPacketEnable. While rxnfgpc is the Number of good (non-erred with
legal length) Rx packets (from the network) regardless of packet
filtering and receive enablement. Thus hw_stats->gprc can be > rxnfgpc
and this calculation should be removed from the calculation of ierrors.
Validated with testpmd by sending packets to the interface without
forwarding enabled - packets should be dropped and the error counters
incremented.
Fixes: f6bf669b99 ("ixgbe: account more Rx errors")
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Balazs Nemeth <balazs.nemeth@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Marvin Liu <yong.liu@intel.com>
ixgbe_recv_pkts_lro uses field rx_free_trigger
in structure ixgbe_rx_queue, but that field is only defined
if IXGBE_RX_ALLOW_BULK_ALLOC is enabled, so even though
that field is not used when it is disabled,
compiler complains about it.
Therefore, the lines of code that use that field
have been ifdef.
Fixes: 8eecb329 ("ixgbe: add LRO support")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Add ixgbe_dev_free_queues() function and call it from close() functions.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch depends on the Port Hotplug Framework.
It implements the eth_dev_uninit functions for rte_ixgbe_pmd and
rte_ixgbevf_pmd.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
ierrors only included a base set of error statistics, this patch adds
additional error registers to ierrors.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Add the NIC/HW specific stats that were removed from rte_ethdev.c to
the extended stats in ixgbe.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Move stats register reads to ixgbe_read_stats_registers() as it will be
used by the functions to retrieve stats and extended stats.
Signed-off-by: Maryam Tahhan <maryam.tahhan@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
add function to support ethtool ops:
- get_reg_length
- get_regs
- get_eeprom_length
- get_eeprom
- set_eeprom
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
- set_mac_addr
Signed-off-by: Liang-Min Larry Wang <liang-min.wang@intel.com>
Acked-by: Andrew Harvey <agh@cisco.com>
Acked-by: David Harton <dharton@cisco.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Move malloc inside eal and create a new section in MAINTAINERS file for
Memory Allocation in EAL.
Create a dummy malloc library to avoid breaking applications that have
librte_malloc in their DT_NEEDED entries.
This is the first step towards using malloc to allocate memory directly
from memsegs. Thus, memzones would allocate memory through malloc,
allowing to free memzones.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
To unify packet type among all PMDs, bit masks of packet type for
'ol_flags' are replaced by unified packet type.
To avoid breaking ABI compatibility, all the changes would be
enabled by RTE_NEXT_ABI.
Note that around 2.5% performance drop (64B) was observed of doing
4 ports (1 port per 82599 card) IO forwarding on the same SNB core.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
In order to unify the packet type, the field of 'packet_type' in
'struct rte_mbuf' needs to be extended from 16 to 32 bits.
Accordingly, some fields in 'struct rte_mbuf' are re-organized to support
this change for Vector PMD.
As 'struct rte_kni_mbuf' for KNI should be right mapped to
'struct rte_mbuf', it should be modified accordingly.
In ixgbe PMD driver, corresponding changes are added for the mbuf changes,
especially the bit masks of packet type for 'ol_flags' are replaced by
unified packet type. In addition, more packet types (UDP, TCP and SCTP)
are supported in vectorized ixgbe PMD.
To avoid breaking ABI compatibility, all the changes would be enabled by
RTE_NEXT_ABI.
Note that around 2% performance drop (64B) was observed of doing 4 ports
(1 port per 82599 card) IO forwarding on the same SNB core.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
There's a parameter "autoneg on|off" in testpmd CLI "set flow_ctrl ...". This
parameter is used to enable/disable auto negotiation for flow control. But it's
not supported yet.
The auto negotiation is enabled by default, we have no way to disable it. This
patch lets the parameter "autoneg on|off" be supproted.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
When initialize the hardware, the stat should be reset.
Otherwise when detach then attach port, the stat will not
be re-init to zero.
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Add ixgbe support for new ethdev APIs to enable and read IEEE1588
PTP timestamps.
Signed-off-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
To support querying hash key size per port, an new field of
'hash_key_size' was added in 'struct rte_eth_dev_info' for storing
hash key size in bytes.
The correct hash key size in bytes should be filled into the
'struct rte_eth_dev_info', to support querying it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This path renames the mirror type in rte_eth_mirror_conf and macros,
and rework the mirror set in ixgbe drivers by using new definition.
It also fixes some coding style.
Test report: http://dpdk.org/ml/archives/dev/2015-June/019118.html
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Rename rte_eth_vmdq_mirror_conf to rte_eth_mirror_conf and move
the maximum rule id check from ethdev level to driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Little endian to CPU order conversion had been added for reading
vlan tag from RX descriptor, while its original source line was
forgotten to delete. That's a discarded source line and should be
deleted.
Fixes: 23fcffe8ff ("ixgbe: fix id and hash with flow director")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The parameter tx_free_thresh is not consistent between the drivers:
some use it as rte_eth_tx_burst() requires, some release buffers when
the number of free descriptors drop below this value.
Let's use it as most fast-path code does, which is the latter, and update
comments throughout the code to reflect that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The function to clear the TX ring when a port was being closed, e.g. on
exit in testpmd, was not checking the mbuf refcnt before freeing it.
Since the function in the vector driver to clear the ring after TX does
not set the pointer to NULL post-free, this caused crashes if mbuf
debugging was turned on.
To reproduce the issue, ensure the follow config variables are set:
RTE_IXGBE_INC_VECTOR
RTE_LIBRTE_MBUF_DEBUG
Then compile up and run testpmd using 10G ports with the vector driver.
Start traffic and let some flow through, then type "stop" and "quit" at
the testpmd prompt, and crash will occur. Output below:
testpmd> quit
Stopping port 0...done
Stopping port 1...PANIC in rte_mbuf_sanity_check():
bad ref cnt
[New Thread 0x7fffabfff700 (LWP 145312)]
[New Thread 0x7fffb47fe700 (LWP 145311)]
[New Thread 0x7fffb4fff700 (LWP 145310)]
[New Thread 0x7ffff6cd5700 (LWP 145309)]
18: [/home/bruce/dpdk.org/x86_64-native-linuxapp-gcc/app/testpmd(_start+0x29)
<....snip for brevity...>
Program received signal SIGABRT, Aborted.
0x00007ffff7120a98 in raise () from /lib64/libc.so.6
A similar error occurs when clearing the RX ring, which is also fixed by
this patch.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
As well as the fast-path functions in the rxtx code, there are also
functions which set up and tear down the descriptor rings. Since these
are not performance critical functions, there is no need to have them
extensively optimized, so we add __attribute__((cold)) to their
definitions. This has the side-effect of making debugging them easier as
the compiler does not optimize them as heavily, so more variables are
accessible by default in gdb.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This patch adds max_link_up_time parameter to mac structure.
This parameter is used to control maximum link polling time in
ixgbe_check_mac_link functions. It is required to prevent long wait
time on x550 PHY that have no external link.
Since x550 is handled by software, we have to reset internal (PHY to
PHY) link when external link changes, and after reset, we have to wait for
this link to be established. As a result of not having interrupts, we have
to poll for link state, and we know that this link comes up much faster
than default 9 seconds. This parameter is added to prevent waiting 9
seconds for link when external link is not established.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Since this 82599 device supports WoL(Wake on LAN), driver needs
a define for the sub device ID.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds support for new x550 PHY IDs:
0x0154 0x0223
0x0154 0x0221
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add new values that vary by MAC type that are introduced in
x540, x550.
And remove some meaningless comments BTW.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a const u32 *mvals pointer to the ixgbe_hw struct to point to an
array of mac-type-dependent values. These can include register
offsets, masks, whatever can be in a u32. When the ixgbe_hw struct
is initialized, a pointer to the appropriate array must be set.
The IXGBE_I2CCTL register references are changed to use it.
Use the mvals array to hold differing values used for
IXGBE_I2C_* symbols.
Use the mvals array to hold differing values used for
IXGBE_*_GPI* symbols.
Use the mvals array to hold differing values use for CIAA and
CIAD symbols.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
According to the hardware, the LINE side of the cs4227 needs to be
set to 10 Gbps SR mode regardless of the configuration of the link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The code in the if statement is specific to the KR PHY. However,
the conditional was only checking for backplane. If the driver
was using the KX4 backplane PHY, this code would execute but
would write to the wrong PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch disables SW LPLU on x557 V2. It also sets the
enter_lplu function pointer to NULL on x557 V2. LPLU will be
implemented in FW for all x557 V2 interfaces. The SW LPLU
implementation must be disabled on V2 to avoid conflicts with
FW. SW LPLU support is still required for x557 V1.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch implements ixgbe_led_on_t_X550em and ixgbe_led_off_t_X550em
function for turning on and off LEDs on X557 external PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The MDIO clock needs to be configured for a specific speed for
x550em. We expected this to be done automatically, but in
the early days of the project this was not happening. We put
code in to do this ourselves.
Eventually, we decided that there is no harm in having SW do
this all the time, so we may not remove this code in the future.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Ensure link is still up after getting the speed, to ensure that the
speed read is valid.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch removes the clearing of the FEC(Forward Error Correction)
bits in ixgbe_setup_kr_speed_x550em. FEC default enablement is
configured via the NVM and SW should not be overriding these defaults
in this function.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds support for x550em KR/iXFI internal link modes. The initial
x550em-10GBASET and x550em-SFP designs use iXFI internal link mode between
the internal PHY and the external PHY.
However future designs will use a KR internal link. This patch is intended
to future proof the driver by adding the KR internal link support in the
driver now.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
EEE(Energy Efficient Ethernet) is not supported on the initial revision
of IXGBE_DEV_ID_X550EM_X_KR. We determine the revision by reading a fuse
register.
Also, the requirements for FEC(Forward Error Correction) have changed
slightly. Now, we don't change the "request" bit at all. When EEE is
enabled, we advertise that we are capable. When EEE is disabled, we do
not advertise that we are capable. This change makes us consistent with
the power-on defaults that are in the NVM.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC(Forward Error Correction) feature had been disabled
because it increases power consumption. However, some customers
want to use it. This patch enables FEC when EEE(Energy Efficient
Ethernet) is disabled; FEC was already being disabled when EEE
was enabled, but now both are done in the same function. The two
features are not allowed to be enabled at the same time. The two
features cannot both be disabled. If this ability is ever
determined to be needed, we will need to define a new user parameter
to control FEC independently of EEE.
Fixes: d4c9ffd4fe ("ixgbe/base: disable X550em FEC to save power")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
During init, check the ucode running in the CS4227. If
it is not responding correctly, reset the part. This is
a global reset so it must only be done the first time a
driver loads after power-on.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Because each IOSF access requires the use of multiple registers,
use a semaphore to serialize those accesses.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a helper function to wait for IOSF accesses to complete. Also
perform this wait before each access, as specified in the datasheet.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
x550em has two different bus speeds, 300 MHz and 400 MHz.
A bit in a fuse register tells which it is, with a 1 meaning
the bus is running at 300 MHz.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
In UniPHY we have 2 IOSF targets that are UniPHY related. We can
write to PHY and PCS. In earlier times I've been told that there
were 2 separate PCS targets for IOSF commands and that's why I
implemented it with 2 defines and adding hw->bus.lan_id, but lately
I confirmed with HW that FW takes care of which PCS "slice" we are
talking to and is directing writes to correct one, so KX4_PCS1
target is dead now and we cannot use it.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch powers down the x550em PHY on over-temp events. The
PHY firmware is supposed to do this autonomously but that isn't
implemented. The short-term stop-gap solution is for SW to power
down the PHY when it reports an overtemp event.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds identify SFP module support for x550em. x550em
support returns an error for SFP module types not supported by
x550em design.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch updates the x550em SFP link setup by adding
ixgbe_sfp_type_unknown and ixgbe_sfp_type_not_present case expression
to the ixgbe_setup_mac_link_sfp_x550em SFP type switch statement. This
handles the case when no module is present.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Fix the warning caused by an uninitialized variable which might have
been used.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Configure the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the 82599 flow.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On systems that support LPLU in the firmware, the driver wouldn't be
aware of the LPLU speed change, and it wouldn't cache the new value when
the driver resumes. This patch emulates the same behavior by restoring
the previous autoneg settings to autoneg_advertised.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch updates x550em LPLU (Low Power Link Up) to use the
MAC ops setup_link function pointer.
This removes redundant code and provides iXFI and KR support
between internal and external PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Because we acquire two semaphore bits before setting the SWFW_SYNC
register, we should release them in the reverse order that they
were acquired.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. The PCI transactions pending bit sticks high
when there were pending transactions, we should wait and then continue
with our reset flow.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch fixes comment description for setting 2.5G and 5G speeds in
ixgbe_setup_phy_link_generic.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Adds define for the number of bits needed to shift the EEE_SU register
in order to get the value of TEEE_DLY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This path changes ((P == 0) ? (<value for port 0>) : (<value for port 1>))
register definition into ((P) ? <value for port 1> : <value for port 0>)
style.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Update readme file to show the version of the base code.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For there're only laser ports on x550 before, we only considered laser
ports for the testpmd CLIs "port start/stop ...". Now we have new x550
devices which have copper ports. Use the API for copper to enable/disable
these ports.
And also let the testpmd CLI "set link-up/down ..." support copper
ports.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
When TSO is used with IPv6, generated frames are incorrect.
L4 frame is OK, but length field of IPv6 header was not populated correctly.
IXGBE_ADVTXD_TUCMD_IPV6 flag is set for better readability, even if it
does nothing.
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Current ixgbe VF base driver only really read the status register when:
- get_link_status is true
- link reset
- mailbox timeout.
We only set get_link_status to true when we start the PF/VF, so
following calls to ixgbe_dev_link_update will just keep the old link
status unless the link has been reset.
Because of this behaviour, when the link status of the PF changes after
the VF has been initialized, we do not read the current status register
from the nic and instead we just keep the old link status.
Fix the problem by setting this field to true before calling
ixgbe_check_link function from base driver. We don't need to check after
this call for get_link_status anymore, so remove it.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
The logic to select ixgbe VF RX function is different than PF side.
There are a few issues with its current state:
- it does not allow to select ixgbe_recv_pkts_vec among other options.
- it can cause memory corruption for scatter mode as it does not allocate
enough entries in sw_ring.
- when checksum is enabled, incorrect vector RX function is selected.
To solve above issues, change the VF RX function selection logic to
mimic PF side.
Signed-off-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The flexbytes offset can not be set, because the value is over written
when fdir is enabled.
This patch fixes this issue, and also removes some reduplicate lines.
Fixes: d54a988826 ("ixgbe: support flexpayload configuration of flow director")
Reported-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: David Marchand <david.marchand@6wind.com>
On x550, flow director doesn't support other IP packets directly.
If we want to monitor IP other packets, the L4 protocol and ports must
be masked. It means, on x550, if we want to add a flow director filter
for other IP packets, a flow director mask must have been configed to
mask L4 protocol and ports.
Return err when the user try to config a flow director filter for other
IP packets without flow director mask configed before. And print err log
for it.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch sets the setup_EEE function pointer to NULL for the
interfaces which do not support EEE (Energy Efficient Ethernet).
Currently only the KR backplane interface (0x15AB) supports EEE.
Setting this pointer to NULL prevents EEE registers from being
incorrectly modified and gives base drivers a flag to check for
EEE support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em PHY reset function ixgbe_reset_phy_t_X550em.
ixgbe_reset_phy_t_X550em calls the reset PHY generic, and then enables
the x550em PHY LASI(Link Alarm Status Interrupt) interrupts.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Set the lan_id before the first I2C access. The existing call was
clearly being done after a previous I2C access in the same function
and that can't be right, so call the set_lan_id method earlier. At
this point it probably doesn't matter for this QSFP function, but
it makes sense to do it consistently anyway.
On X550, be sure to set the lan_id before using it to configure the
mux control output, else the mux will not be controlled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The introduction of ixgbe_get_bus_info_X550em failed to call the
set_lan_id method to set the func and lan_id and deal with port-
swapped configurations. Add the call to resolve the problem.
Fixes: 4cf0bb32a9 ("ixgbe/base: get X550 bus info")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds ixgbe_check_link_t_X550em for checking x550em
PHY link. We check that both the MAC and external x550em PHY have link.
This is to avoid a false link up between the internal and external PHY
when the external PHY doesn't have link.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em external PHY interrupt and forced 1G/10G
support. Support includes enabling and handling Link Status
Change and Thermal Sensor interrupt. ixgbe_handle_lasi has been added
to the API for handling the interrupts received from x550em PHY.
ixgbe_enable_lasi_ext_t_x550em and ixgbe_get_lasi_ext_t_x550em have been
added to X550em to enable mask and check interrupt flags for x550em PHY.
Forced 1G/10G link speed is handled via ixgbe_setup_mac_link_t_X550em.
ixgbe_setup_mac_link_t_X550em sets up the internal PHY and
external PHY link to either 10G or 1G based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds x550em Auto neg Flow Control support to
ixgbe_device_supports_autoneg_fc and sets the x550em setup_fc function
pointer to ixgbe_setup_fc_generic. ixgbe_setup_fc_generic is used for
x550em because flow control is setup on the external PHY via MDIO, when
ixgbe_setup_fc_X550em sets up flow control on the internal PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch cleans up the ixgbe_setup_internal_phy_ x550em() function as follows:
- Renames it to ixgbe_setup_internal_phy_t_x550em to clarify that it is
specific to copper
- Returns an error if called for non-copper devices
- Corrects the comments
- Removed the LASI(Link Alarm Status Interrupt) status register checks as
this was incorrect and never worked correctly anyway.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch changes the return value for ixgbe_setup_internal_phy_t_x550em
when link is down to IXGBE_SUCCESS.
The driver will call ixgbe_setup_internal_phy_t_x550em when a link status
change is reported. The links status change can occur on link up or link
down, and if the link status change is for link down then there is no iXFI
setup necessary and no error condition needs to be returned.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The following patch moves the handling of the I2C MUX (which is only
used for x550em SFP+ devices) out of the ixgbe_x540.c file and
into the ixgbe_x550.c file where it belongs.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The init flow is simplified. We no longer wait for the PHY FW init
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.
The PHY initialization has been simplified and now only requires that
the PHY FW be "un-stalled". SW no longer needs to put the PHY in
low-power mode or enable the transceiver.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For the KR backplane which is different from other backplane,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SW Low Power Link Up (LPLU) support for x550em PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SFP+ dual-speed support.
82599 fiber link code was moved from ixgbe_82599.c to ixgbe_commom.c
for use by X550em, and the API was updated to support the common code
usage. SFP MAC link code is added to x550em.
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC (Forward Error Correction) feature can improve BER (Bit Error Rate)
but uses more power to do so. It also cannot be used with
EEE (Energy Efficient Ethernet).
EEE is an important feature, and we have no known BER issues, so FEC
is not needed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. So,
put the code in a function so it can be used in more than one place.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The driver now needs to issue a firmware command to inform the
firmware that a driver is coming up. This prevents the possibility
of the firmware and the driver configuring the PHY at the same
time. Upon completion of the command, the firmware will no longer
be configuring the PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
A retry count of 10 is likely to run into problems on X550 devices
that have to detect and reset unresponsive CS4227 devices. So,
reduce the I2C retry count to 3 for X550 and above. This should
avoid any possible regressions in existing devices.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Most I2C accesses take and release semaphores for each access. It's
also necessary to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
All bits in FDIRTCPM and FDIRUDPM are set to 1 when
ixgbe_fdir_set_input_mask_82599 is called. Not settings these bits will cause
TCP and UDP packets to be filtered out when NVGRE or VXLAN mode is enabled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch moves the check of the return value from
ixgbe_start_hw_generic after the function is called.
Previously we had the code to disable relaxed ordering in
between, which seems a bit out of place.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Remove the redundant "from".
There's a typo in the code comment for FC end
of Frame Exception (FCEOFe/IPE), so fixed the typo.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move ixgbe PMD to drivers/net directory.
As part of the move, we rename the ixgbe directory, containing the
ixgbe "base driver" code, from "ixgbe" to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
