The A3700 has a different GPIO controller and thus, do not use the old (and
shared) code for Marvell.
The pinctrl driver, also part of the controller, is not supported yet (but
the implementation should be straightforward).
Sponsored by: Rubicon Communications, LLC (Netgate)
This allows SDIO (through CAM) to attach to an upstream, e.g.,
..
sdhci_bcm0 pnpinfo name=mmc@7e300000 compat=brcm,bcm2835-mmc
sdiob0
..
Without this, upon trying to load sdio, we would panic with
"bus_add_child is not implemented".
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
In the DMA case, given we disable the data interrupts, we never seem
to get DATA_END. Given we are relying on DMA interrupts we are not
using the SDHCI state machine and hence only call into
sdhci_platform_will_handle() for the first check of data.
We do not call "will handle" for any following round trips of the same
transaction if block size * count > BCM_DMA_BLOCK_SIZE.
Manually check "left" in the DMA interrupt handler to see if we have at
least another full BCM_DMA_BLOCK_SIZE to handle.
Without this change we would DMA that and then even start a DMA with
left == 0 which would lead to a timeout and error.
Now we re-enable data interrupts and return and let the SDHCI generic
interrupt handler and state machine pick the SPACE_AVAIL up and then
find that it should punt to the pio_handler for the remaining bytes
or finish the data transaction.
With this change block mode seems to work beyond 7 * 64byte blocks,
which worked as it was below BCM_DMA_BLOCK_SIZE.
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20199
Extending what the initial revision, r273264, r276985, r277346 have
started for the transfer mode and command registers, another pair of
16bit registers written in sequence are block size and block count,
which fall together onto the same 32bit line and hence the same
register(s) would be written twice in sequence for those as well.
Use a similar approach to transfer mode and command and save the writes
to either of the block regiters and then only execute a write once.
We can do this as with transfer mode their values are meaningless until
a command is issued so we can use that write to command as a trigger
to also write out the block registers.
Compared to transfer mode and command the value of block count can
change, so we need to keep state and actually read the block registers
back the first time after a write.
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20197
These calls are not the same in general: the former will dequeue the
page if it is enqueued, while the latter will just leave it alone. But,
all existing uses of the former apply to unmanaged pages, which are
never enqueued in the first place. No functional change intended.
Reviewed by: kib
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20470
cpufunc, in terms of __builtin_ffs and the like, for arm32 v6 and v7
architectures, and use those, rather than the simple libkern
implementations, in building arm32 kernels.
Reviewed by: manu
Approved by: kib, markj (mentors)
Tested by: iz-rpi03_hs-karlsruhe.de, mikael.urankar_gmail.com, ian
Differential Revision: https://reviews.freebsd.org/D20412
Some clocks used the NM type but this clock is for the ones with the
formula "clk = clkin / n / m" and not "clk = clkin * n / m"
Use the new frac clock for them.
Add a clock driver for clock that can either be used in integer mode
with one N factor and one M divider or in fractional mode where the
output frequency is chosen between two predifined output.
This was enumerated with exhaustive search for sys/eventhandler.h includes,
cross-referenced against EVENTHANDLER_* usage with the comm(1) utility. Manual
checking was performed to avoid redundant includes in some drivers where a
common os_bsd.h (for example) included sys/eventhandler.h indirectly, but it is
possible some of these are redundant with driver-specific headers in ways I
didn't notice.
(These CUs did not show up as missing eventhandler.h in tinderbox.)
X-MFC-With: r347984
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
Having IPSEC compiled into the kernel imposes a non-trivial
performance penalty on multi-threaded workloads due to IPSEC
refcounting. In my benchmarks of multi-threaded UDP
transmit (connected sockets), I've seen a roughly 20% performance
penalty when the IPSEC option is included in the kernel (16.8Mpps
vs 13.8Mpps with 32 senders on a 14 core / 28 HTT Xeon
2697v3)). This is largely due to key_addref() incrementing and
decrementing an atomic reference count on the default
policy. This cause all CPUs to stall on the same cacheline, as it
bounces between different CPUs.
Given that relatively few users use ipsec, and that it can be
loaded as a module, it seems reasonable to ask those users to
load the ipsec module so as to avoid imposing this penalty on the
GENERIC kernel. Its my hope that this will make FreeBSD look
better in "out of the box" benchmark comparisons with other
operating systems.
Many thanks to ae for fixing auto-loading of ipsec.ko when
ifconfig tries to configure ipsec, and to cy for volunteering
to ensure the the racoon ports will load the ipsec.ko module
Reviewed by: cem, cy, delphij, gnn, jhb, jpaetzel
Differential Revision: https://reviews.freebsd.org/D20163
tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
Use it wherever COMPAT_FREEBSD11 is currently specified, like r309749.
Reviewed by: imp, jhb, markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20120
We don't have the display engine driver commited in FreeBSD yet so it is
useless to expose the clocks yet (and also it have not been tested on H5).
Reported by: Manuel Stühn (freebsdnewbie@freenet.de)
PR: 237571
MFC after: 1 week
Allwinner H3 and H5 share many internal components, that's why they can
use the same drivers.
This patch adds the compatible strings to enable clock drivers
probing on Allwinner NanoPI NEO2 device.
Tested on: NanoPi NEO2 (by submitter), OrangePi PC2 (by manu)
Submitted by: Manuel Stühn (freebsdnewbie@freenet.de)
MFC after: 2 months
Differential Revision: https://reviews.freebsd.org/D20069
occasional spurious interrupts are a normal thing on this hardware. Also,
change the name of the cpu-local interrupt controller driver from local_intc
to lintc, because the name gets built into interrupt names, which have to
fit into a 19-byte field for stats reporting (so this allows 5 more bytes
of the actual interrupt name to be displayed).
Due to three conditions the codec driver for Allwinner A10/A20 and H3/H5 did not work properly here:
Wrong bit position for the analog audio reset
Hardware Reset of codec was not de-asserted correctly
Linux DTS file did not contain the address of the analog register the way as the driver was expecting it.
This patch proposes fixes for those three parts.
Submitted by: freebsdnewbie@freenet.de (Manuel Stühn)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19910
The code previously set up interrupt handlers for all the interrupt
resources available, including for timers that are not in use. That could
lead to interrupt storms. For example, if boot firmware enabled the virtual
timer but the kernel is using the physical timer, it could get flooded with
interrupts on the virtual timer which it cannot shut off. By only setting
up an interrupt handler for the hardware that will actually be used, any
interrupts from other timer units will remain masked in the interrupt
controller.
Differential Revision: https://reviews.freebsd.org/D19871
The old clocks are disconneted from the build since r337344.
Remove all those pseudo drivers. The only one remaining is for gmac
(the ethernet controller) so move it to sys/arm/allwinner.
While here remove a83t support from gmacclk as it is unneeded since r326114.
MFC after: 1 month
Since 5.0 DTS the syscon controller have a new compatible as it
exports new subnodes, we currently only use it as a syscon provider
so just add the new compatible.
Tested On: H3
MFC after: 1 month
Since latest DTS update the rtc is supposed to register two clocks :
- osc32k (the 32k oscillator on the board that the RTC uses directly and
that other peripheral can use)
- iosc (the internal oscillator of the RTC when available which frequency
depend on the SoC revision)
Since we need the RTC before the proper clock control unit (because it uses
those clocks) attach it a BUS_PASS_BUS + MIDDLE and attach the clock control
unit at BUS_PASS_BUS + LAST for the SoC that requires it.
Tested On: A20, H3, A64
MFC after: 1 month
Correct a typo in the RPI-B ethernet config - the RPi-B includes a
SMC LAN9512 USB bridge and Ethernet 10/100 NIC/phy. The phy part of
this is supported by smscphy.
Tested On: RPi1 Model B
Approved by: grog, jhb (mentors)
MFC after: 3 days
Since r324184 the root node compatible for the original Raspberry Pi
is "brcm,bcm2835", add it to the compatible list of bcm2835_cpufreq.
Tested On: RPi1 Model B
Note that the default Das U-Boot FDT does not include a cpus clause
so actually adding a bcm2835_cpufreq device requires adding a FDT
overlay defining the cpu.
Approved by: grog, jhb (mentors)
MFC after: 3 days
If a custom block size requested, use it, otherwise revert to the previous logic
of using just a data size if it's less than MMC_BLOCK_SIZE, and MMC_BLOCK_SIZE otherwise.
Reviewed by: bz
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D19783
In r337703 DTS files were updated to Linux 4.18, including Linux commit
4d8b032d3c03f4e9788a18bbb51b10e6c9e8a56b which removed the `phy_id`
property from am335x-bone-common (as the property was deprecated).
Use `phy-handle` via fdt_get_phyaddr, keeping the existing code as a
fallback for old DTBs.
PR: 236624
Submitted by: manu, Gerald Aryeetey <aryeeteygerald_rogers.com>
Reported by: Gerald Aryeetey
Reviewed by: manu
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19814
Using DFLTPHYS/MAXPHYS is not always OK, instead make it possible for the
controller driver to provide maximum data size to MMCCAM, and use it there.
The old stack already does this.
Reviewed by: manu
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D15892
Similar to bcm2835_sdhost.c add a TUNABLE and SYSCTL to selectively
turn on debugging printfs if debugging is turned on at compile time.
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Reviewed by: gonzo, andrew
Differential Revision: https://reviews.freebsd.org/D19745
When comparing best frequencies use the absolute value.
If we do not do that we end up choosing an always lower value than
the best one if the exact freq cannot be met.
MFC after: 2 weeks
In current code, the delay argument in FDT_PLATFORM_DEF(2) improperly
initialize refs field from kobj_class structure instead of delay_count
field.
This causes not working DELAY() function (due to never initialized
delay_count) in earlier boot stages, until the first timer was attached.
MFC after: 2 weeks
Add the infrastructure to allow MD procctl(2) commands, and use it to
introduce amd64 PTI control and reporting. PTI mode cannot be
modified for existing pmap, the knob controls PTI of the new vmspace
created on exec.
Requested by: jhb
Reviewed by: jhb, markj (previous version)
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
PTI mode for the process pmap on exec is activated iff P_MD_PTI is set.
On exec, the existing vmspace can be reused only if pti mode of the
pmap matches the P_MD_PTI flag of the process. Add MD
cpu_exec_vmspace_reuse() callback for exec_new_vmspace() which can
vetoed reuse of the existing vmspace.
MFC note: md_flags change struct proc KBI.
Reviewed by: jhb, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
In all of the architectures we have today, we always use PAGE_SIZE.
While in theory one could define different things, none of the
current architectures do, even the ones that have transitioned from
32-bit to 64-bit like i386 and arm. Some ancient mips binaries on
other systems used 8k instead of 4k, but we don't support running
those and likely never will due to their age and obscurity.
Reviewed by: imp (who also contributed the commit message)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19280
Skylake Xeons.
See SDM rev. 68 Vol 3 4.6.2 Protection Keys and the description of the
RDPKRU and WRPKRU instructions.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D18893
The charging current can be set using steps
from 0: 200mA to 13: 2800mA (200mA/step).
While there, fix battery charging current related
sensor descriptions.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D19212
battery charging, charge state, voltage, charging current, discharging current,
battery capacity etc. can be obtained via sysctl.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D19145
With this change, randomization can be enabled for all non-fixed
mappings. It means that the base address for the mapping is selected
with a guaranteed amount of entropy (bits). If the mapping was
requested to be superpage aligned, the randomization honours the
superpage attributes.
Although the value of ASLR is diminshing over time as exploit authors
work out simple ASLR bypass techniques, it elimintates the trivial
exploitation of certain vulnerabilities, at least in theory. This
implementation is relatively small and happens at the correct
architectural level. Also, it is not expected to introduce
regressions in existing cases when turned off (default for now), or
cause any significant maintaince burden.
The randomization is done on a best-effort basis - that is, the
allocator falls back to a first fit strategy if fragmentation prevents
entropy injection. It is trivial to implement a strong mode where
failure to guarantee the requested amount of entropy results in
mapping request failure, but I do not consider that to be usable.
I have not fine-tuned the amount of entropy injected right now. It is
only a quantitive change that will not change the implementation. The
current amount is controlled by aslr_pages_rnd.
To not spoil coalescing optimizations, to reduce the page table
fragmentation inherent to ASLR, and to keep the transient superpage
promotion for the malloced memory, locality clustering is implemented
for anonymous private mappings, which are automatically grouped until
fragmentation kicks in. The initial location for the anon group range
is, of course, randomized. This is controlled by vm.cluster_anon,
enabled by default.
The default mode keeps the sbrk area unpopulated by other mappings,
but this can be turned off, which gives much more breathing bits on
architectures with small address space, such as i386. This is tied
with the question of following an application's hint about the mmap(2)
base address. Testing shows that ignoring the hint does not affect the
function of common applications, but I would expect more demanding
code could break. By default sbrk is preserved and mmap hints are
satisfied, which can be changed by using the
kern.elf{32,64}.aslr.honor_sbrk sysctl.
ASLR is enabled on per-ABI basis, and currently it is only allowed on
FreeBSD native i386 and amd64 (including compat 32bit) ABIs. Support
for additional architectures will be added after further testing.
Both per-process and per-image controls are implemented:
- procctl(2) adds PROC_ASLR_CTL/PROC_ASLR_STATUS;
- NT_FREEBSD_FCTL_ASLR_DISABLE feature control note bit makes it possible
to force ASLR off for the given binary. (A tool to edit the feature
control note is in development.)
Global controls are:
- kern.elf{32,64}.aslr.enable - for non-fixed mappings done by mmap(2);
- kern.elf{32,64}.aslr.pie_enable - for PIE image activation mappings;
- kern.elf{32,64}.aslr.honor_sbrk - allow to use sbrk area for mmap(2);
- vm.cluster_anon - enables anon mapping clustering.
PR: 208580 (exp runs)
Exp-runs done by: antoine
Reviewed by: markj (previous version)
Discussed with: emaste
Tested by: pho
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D5603
- for now, alignments bigger that page size is allowed only for buffers
allocated by bus_dmamem_alloc(), cover this fact by KASSERT.
- never bounce buffers allocated by bus_dmamem_alloc(), these always comply
with the required rules (alignment, boundary, address range).
MFC after: 1 week
Reviewed by: jah
PR: 235542
reading some events from the interrupt status registers. These events
are reported to devd via system "PMU" and subsystem "Battery", "AC"
and "USB" such as plugged/unplugged, absent, charged and charging.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D19116
Bump up MAX_HWCNT and MAX_EXCNT to 32 when ACPI is enabled. These are
the sizes of the hwregions and exregions arrays respectively. ACPI
firmware typically has more memory regions and the current value of
16 is not sufficient for some platforms.
This commit fixes a failure seen with AMI firmware on Cavium's Sabre
ThunderX2 reference platform. This platform needs 21 physical memory
regions and 18 excluded regions to boot correctly with the current
firmware release.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D19073
U-Boot will leave the ephy reset de-asserted and the MAC soft reset will
fail on these boards with internal PHY and no link established. Toggle reset
again before proceeding to attach/init.
MFC after: 1 week
This was intended to fix the soft reset timeout on boot for OrangePi One/R1
with internal PHY, but seems to cause other problems later on due to soft
resetting around some state changes that may or may not make the NIC
non-functional.
Reverting this for now while a better solution is sought out.
Add parentheses to perform assignment before comparison. The prior
condition worked because fdt_parent_addr_cells returns 1 for the DTB
on which fdt_fixup_ranges is called and accidentally par_addr_cells
ends up to be set to the same value.
PR: 210705
Submitted by: David Binderman <dcb314@hotmail.com>
MFC after: 1 week
From NetBSD: Since the MAC can get stuck in reset state with no link, ignore
reset timeouts and continue with initializing the device.
Fixes "soft reset timeout" issue at boot with no network cable plugged in.
awg_init may be called multiple times throughout normal interface usage, so
the tx/rx descriptor base address registers must be written after each MAC
reset and are moved as such.
This problem has been observed on FreeBSD, H3/H2+ devices with an internal
PHY (includes OrangePi R1, OrangePi One at least).
Reviewed by: manu, ganbold
Obtained from: NetBSD
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18844
mv_pci driver reads PCI memory window layout from DTB data and if the
data is incomplete falls back to default value. The value is too small
to fit two PCI spaces for mwlwifi devices on WRT3200ACM so the resource
allocation for them fails. Increase the default to 4Mb from 1Mb so
the devices can be properly attached.
MFC after: 1 week
front-end doesn't support SDMA or the latter implements a platform-
specific transfer method instead. While at it, factor out allocation
and freeing of SDMA resources to sdhci_dma_{alloc,free}() in order to
keep the code more readable when adding support for ADMA variants.
o Base the size of the SDMA bounce buffer on MAXPHYS up to the maximum
of 512 KiB instead of using a fixed 4-KiB-buffer. With the default
MAXPHYS of 128 KiB and depending on the controller and medium, this
reduces the number of SDHCI interrupts by a factor of ~16 to ~32 on
sequential reads while an increase of throughput of up to ~84 % was
seen.
Front-ends for broken controllers that only support an SDMA buffer
boundary of a specific size may set SDHCI_QUIRK_BROKEN_SDMA_BOUNDARY
and supply a size via struct sdhci_slot. According to Linux, only
Qualcomm MSM-type SDHCI controllers are affected by this, though.
Requested by: Shreyank Amartya (unconditional bump to 512 KiB)
o Introduce a SDHCI_DEPEND macro for specifying the dependency of the
front-end modules on the sdhci(4) one and bump the module version
of sdhci(4) to 2 via an also newly introduced SDHCI_VERSION in order
to ensure that all components are in sync WRT struct sdhci_slot.
o In sdhci(4):
- Make pointers const were applicable,
- replace a few device_printf(9) calls with slot_printf() for
consistency, and
- sync some local functions with their prototypes WRT static.
This fix booting on A64 boards when disabling the unused regulators at boot.
We did disable all the regulator handled by register 0x13 which of course contain
mandatory regulators for the board to be up.
Reported by: Mark Millard <marklmi@yahoo.com>
X-MFC-With: r340848
icu is a interrupt concentrator in the CP110 block and gicp
is a gic extension to allow interrupts in the CP block to be turned
into GIC SPI interrupts
Sponsored by: Rubicon Communications, LLC ("Netgate")
The cp110 clock controller controls the clocks and gate of the CP110
hardware block.
Every clock/gate are implemented except the NAND clock.
Sponsored by: Rubicon Communications, LLC ("Netgate")
The first two clocks are for the clusters and their frequencies can be
found reading a register. Then a fixed 1200Mhz clock is present and two
fixed clocks, 'mss' which is 1200 / 6 and 'sdio' which is 1200 / 3.
Sponsored by: Rubicon Communications, LLC ("Netgate")
On some architectures, the structures returned by PT_GET*REGS were not
fully populated and could contain uninitialized stack memory. The same
issue existed with the register files in procfs.
Reported by: Thomas Barabosch, Fraunhofer FKIE
Reviewed by: kib
MFC after: 3 days
Security: kernel stack memory disclosure
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18421
Add generic implementation for bus_deactivate_resource method. Without
it bus_release_resource fails with "Failed to release active resource"
message
MFC after: 1 week
Fix reporting of SS_ONSTACK in nested signal delivery when sigaltstack()
is used on some architectures.
Add a unit test for this. I tested the test by introducing the bug
on amd64. I did not test it on other architectures.
Reviewed by: kib
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D18347
On arm64 and riscv platforms, sendsig() failed to zero the signal
frame before copying it out to userspace. Zero it.
On arm, I believe all the contents of the frame were initialized,
so there was no disclosure. However, explicitly zero the whole frame
because that fact could inadvertently change in the future,
it's more clear to the reader, and I could be wrong in the first place.
MFC after: 2 days
Security: similar to FreeBSD-EN-18:12.mem and CVE-2018-17155
Sponsored by: Dell EMC Isilon
Instead of routing the phy when enabling it, do the configuration
and routing in the phynode_usb_set_mode function.
While here, if we don't have a vbus detection method, enable the phy
if requested.
MFC after: 1 month
On arm64 (where INTRNG is enabled), the interrupts have to be mapped
with ACPI_BUS_MAP_INTR() before adding them as resources to devices.
The earlier code did the mapping before calling acpi_set_resource(),
which bypassed code that checked for PCI link interrupts.
To fix this, move the call to map interrupts into acpi_set_resource()
and that requires additional work to lookup interrupt properties.
The changes here are to:
* extend acpi_lookup_irq_handler() to lookup an irq in the ACPI
resources
* create a helper function acpi_map_intr() which uses the updated
acpi_lookup_irq_handler() to look up an irq, and then map it
with ACPI_BUS_MAP_INTR()
* use acpi_map_intr() in acpi_pcib_route_interrupt() to map
pci link interrupts.
With these changes, we can drop the ifdefs in acpi_resource.c, and
we can also drop the call for mapping interrupts in generic_timer.c
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D17790
recent changes in spibus and allow the use of different SPI modes on
the same bus.
Reported by: ian
Sponsored by: Rubicon Communications, LLC (Netgate)
r306041 changed ld invocations for converting binary files to kernel
ELF objects to pass -m, but missed bespoke ld invocations in a pair of
arm file configs (one of which has since been removed).
This is needed to support some external toolchains and lld.
Sponsored by: The FreeBSD Foundation
Replace a call to DELAY(1) with a new cpu_lock_delay() KPI. Currently
cpu_lock_delay() is defined to DELAY(1) on all platforms. However,
platforms with a DELAY() implementation that uses spin locks should
implement a custom cpu_lock_delay() doesn't use locks.
Reviewed by: kib
MFC after: 3 days
Existing base causes conflicts for direct execution of ld-elf.so.1
because default linking base for non-PIE binaries is 0x10000.
Reported and tested by: Mark Millard <marklmi26-fbsd@yahoo.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Add a new 'debugger_on_trap' knob separate from 'debugger_on_panic'
and make the calls to kdb_trap() in MD fatal trap handlers prior to
calling panic() conditional on this new knob instead of
'debugger_on_panic'. Disable the new knob by default. Developers who
wish to recover from a fatal fault by adjusting saved register state
and retrying the faulting instruction can still do so by enabling the
new knob. However, for the more common case this makes the user
experience for panics due to a fatal fault match the user experience
for other panics, e.g. 'c' in DDB will generate a crash dump and
reboot the system rather than being stuck in an infinite loop of fatal
fault messages and DDB prompts.
Reviewed by: kib, avg
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D17768
The loader tunable 'debug.verbose_sysinit' may be used to toggle verbosity.
This is added to the debugging section of these kernconfs to be turned off
in stable branches for clarity of intent.
MFC after: never
All platforms except powerpc use the same values and powerpc shares a
majority of them.
Go ahead and declare AT_NOTELF, AT_UID, and AT_EUID in favor of the
unused AT_DCACHEBSIZE, AT_ICACHEBSIZE, and AT_UCACHEBSIZE for powerpc.
Reviewed by: jhb, imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D17397
In the FDT based probe, check for "arm,armv8-timer" before "arm,armv7-timer".
This gets the description right when the timer node has both entries in
compatible list.
(e.g. RocketChip, lowRISC and derivatives).
RISC-V page table entries support A (accessed) and D (dirty) bits. The
spec makes hardware support for these bits optional. Implementations that
do not manage these bits in hardware raise page faults for accesses to a
valid page without A set and writes to a writable page without D set.
Check for these types of faults when handling a page fault and fixup the
PTE without calling vm_fault if they occur.
Reviewed by: jhb, markj
Approved by: re (gjb)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D17424
We ought to be consistent across our Tier-1 and nearly-Tier-1
architectures, so enable Capsicum for 32-bit armv6/armv7 by default.
PR: 204008
Reviewed by: ian, oshogbo
Approved by: re (gjb)
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17023
These limits are hit on the ThunderX. Also make
arm_physmem_exclude_region() panic rather than fail silently if the
limit on excluded regions is reached.
PR: 231064
Reviewed by: andrew
Approved by: re (kib)
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17073
To support INTRNG with ACPI we need to set a non-zero cross reference value
for the interrupt controller. The GICv3 driver already had this value set,
however it was missed in the GICv2 driver. Fix this by setting xref to the
correct value.
Approved by: re (gjb)
Same as r333305, with Linux 4.17 dts the compatible for the prcm added
'simplebus', it mean that the simplebus driver will attach to it
at the BUS_PASS_BUS pass.
Change the pass for the prcm driver to be at BUS_PASS_BUS so we will win
the attach.
This introduce a problem as this driver needs the omap_scm one to be already
attached. omap_scm also attach at BUS_PASS_BUS but after the prcm one as it is
after in the dtb and the simplebus driver simpy walk the tree to attach it's
children.
Use the bus_new_pass method to defer the frequencies read at BUS_PASS_TIMER.
This fixes booting on pandaboard
Approved by: re (rgrimes)
Fix the build of the GENERIC-MMCCAM kernel config after the sdhci_xenon
driver was commited.
While here correct sdhci_fdt and tegra_sdhci, even with MMCCAM they do
need to depend on sdhci(4)
Reported by: Reshetnikov Dmitriy <genserg@hotmail.com>
Approved by: re (kib)
Sponsored by: Rubicon Communications, LLC ("NetGate")
Exposing max_offset and min_offset defines in public headers is
causing clashes with variable names, for example when building QEMU.
Based on the submission by: royger
Reviewed by: alc, markj (previous version)
Sponsored by: The FreeBSD Foundation (kib)
MFC after: 1 week
Approved by: re (marius)
Differential revision: https://reviews.freebsd.org/D16881
Previously we have been lucky where the state was already in r0, however
this is not guaranteed. Use the passed in register as the location to
store the upper half of the arm VFP registers rather than relying on it
being r0.
Approved by: re (kib)
given in random(4).
This includes updating of the relevant man pages, and no-longer-used
harvesting parameters.
Ensure that the pseudo-unit-test still does something useful, now also
with the "other" algorithm instead of Yarrow.
PR: 230870
Reviewed by: cem
Approved by: so(delphij,gtetlow)
Approved by: re(marius)
Differential Revision: https://reviews.freebsd.org/D16898
error in the function hypercall_memfree(), where the wrong arena was being
passed to kmem_free().
Introduce a per-page flag, VPO_KMEM_EXEC, to mark physical pages that are
mapped in kmem with execute permissions. Use this flag to determine which
arena the kmem virtual addresses are returned to.
Eliminate UMA_SLAB_KRWX. The introduction of VPO_KMEM_EXEC makes it
redundant.
Update the nearby comment for UMA_SLAB_KERNEL.
Reviewed by: kib, markj
Discussed with: jeff
Approved by: re (marius)
Differential Revision: https://reviews.freebsd.org/D16845
Revert r338177, r338176, r338175, r338174, r338172
After long consultations with re@, core members and mmacy, revert
these changes. Followup changes will be made to mark them as
deprecated and prent a message about where to find the up-to-date
driver. Followup commits will be made to make this clear in the
installer. Followup commits to reduce POLA in ways we're still
exploring.
It's anticipated that after the freeze, this will be removed in
13-current (with the residual of the drm2 code copied to
sys/arm/dev/drm2 for the TEGRA port's use w/o the intel or
radeon drivers).
Due to the impending freeze, there was no formal core vote for
this. I've been talking to different core members all day, as well as
Matt Macey and Glen Barber. Nobody is completely happy, all are
grudgingly going along with this. Work is in progress to mitigate
the negative effects as much as possible.
Requested by: re@ (gjb, rgrimes)
a10_timer is currently use in UP allwinner SoC (A10 and A13).
Those don't have the generic arm timer.
The arm generic timecounter is broken in the A64 SoC, some attempts have
been made to fix the glitch but users still reported some minor ones.
Since the A64 (and all Allwinner SoC) still have this timer controller, rework
the driver so we can use it in any SoC.
Since it doesn't have the 64 bits counter on all SoC, use one of the
generic 32 bits counter as the timecounter source.
PR: 229644
Without this the mmc stack sometimes think that we are in in a retune
operation and some command like switch the bus width to 4 bits failed.
We now switch correctly to 4 bits mode for sd card.
Reported by: jmg, others in pine64 irc channel
The boot-time ifunc resolver assumes that it only needs to apply
IRELATIVE relocations to PLT entries. With an upcoming optimization,
this assumption no longer holds, so add the support required to handle
PC-relative relocations targeting GNU_IFUNC symbols.
- Provide a custom symbol lookup routine that can be used in early boot.
The default lookup routine uses kobj, which is not functional at that
point.
- Apply all existing relocations during boot rather than filtering
IRELATIVE relocations.
- Ensure that we continue to apply ifunc relocations in a second pass
when loading a kernel module.
Reviewed by: kib
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D16749
became unused in FreeBSD 12.x as a side-effect of the NUMA-related
changes.)
Reviewed by: kib, markj
Discussed with: jeff, re@
Differential Revision: https://reviews.freebsd.org/D16825
This is an amalgam of a patch by Doug Ambrisko to
generalize uart_acpi_find_device, imp moving the
ACPI table to uart_dev_ns8250.c and advice by jhb
to work around a bug in the EPYC 3151 BIOS
(the BIOS incorrectly marks the serial ports as
disabled)
Reviewed by: imp
MFC after: 8 weeks
Differential Revision: https://reviews.freebsd.org/D16432
Recent DTS use the syscon for the emac controller.
We support this but since U-Boot is still using old DTS it was never
needed for us to add this support, but this is a problem when using upstream
recent DTS and will be when U-Boot will catch up.
While here add a new compatible to the aw_syscon driver as Linux changed it ...
- In configurations with a pseudo devices section, move 'device crypto'
into that section.
- Use a consistent comment. Note that other things common in kernel
configs such as GELI also require 'device crypto', not just IPSEC.
Reviewed by: rgrimes, cem, imp
Differential Revision: https://reviews.freebsd.org/D16775
Missed in r337940.
(It's not like there are any crypto files IPsec doesn't pull in, so it is
unclear what not defining the crypto option was supposed to achieve.)
Reported by: np@
Remove the non-INTRNG code.
Remove left over cut and paste code from the lpc code that was the start for the port.
Set KERNPHYSADDR and KERNVIRTADDR
Tested on Buffalo_WZR2-G300N
Differential Revision: https://reviews.freebsd.org/D16622
Now softc should be retrieved from struct edvev * pointer
with evdev_get_softc() helper.
wmt(4) is a sample of driver that support both KPI.
Reviewed by: hselasky, gonzo
Differential Revision: https://reviews.freebsd.org/D16614
add support for explicitly requesting that pmap_enter() create a 1 MB page
mapping. (Essentially, this feature allows the machine-independent layer
to create superpage mappings preemptively, and not wait for automatic
promotion to occur.)
Export pmap_ps_enabled() to the machine-independent layer.
Add a flag to pmap_pv_insert_pte1() that specifies whether it should fail
or reclaim a PV entry when one is not available.
Refactor pmap_enter_pte1() into two functions, one by the same name, that
is a general-purpose function for creating pte1 mappings, and another,
pmap_enter_1mpage(), that is used to prefault 1 MB read- and/or execute-
only mappings for execve(2), mmap(2), and shmat(2).
In addition, as an optimization to pmap_enter(..., psind=0), eliminate the
use of pte2_is_managed() from pmap_enter(). Unlike the x86 pmap
implementations, armv6 does not have a managed bit defined within the PTE.
So, pte2_is_managed() is actually a call to PHYS_TO_VM_PAGE(), which is O(n)
in the number of vm_phys_segs[]. All but one call to PHYS_TO_VM_PAGE() in
pmap_enter() can be avoided.
Reviewed by: kib, markj, mmel
Tested by: mmel
MFC after: 6 weeks
Differential Revision: https://reviews.freebsd.org/D16555
Now that aw_sid expose nvmem interface, use that to read the calibration
data.
Add support for H5 SoC.
Fix the bindings, we used to have non-upstreamed bindings. Switch to the
one that have been sent upstream. They are not stable yet, so we switch
from custom, wrong, bindings to correct, proposed bindings
Rework aw_sid so it can work with the nvmem interface.
Each SoC expose a set of fuses (for now rootkey/boardid and, if available,
the thermal calibration data). A fuse can be private or public, reading private
fuse needs to be done via some registers instead of reading directly.
Each fuse is exposed as a sysctl.
For now leave the possibility for a driver to read any fuse without using
the nvmem interface as the awg and emac driver use this to generate a mac
address.
It doesn't work since 2 years when we stopped patching DTS.
The DTS now have the correct bindings but they are a lot different
from our hacked ones we used to have (and more representative of the
reality).
Remove the old clocks for allwinner as now all the SoCs have been converted
to clkng.
The only old clock now is the gmac clock which still lives under the /clocks
dts node.
The nvmem interface helps provider of nvmem data to expose themselves to consumer.
NVMEM is generally present on some embedded board in a form of eeprom or fuses.
The nvmem api are helpers for consumer to read/write the cell data from a provider.
Differential Revision: https://reviews.freebsd.org/D16419
Precompute the new PTE before entering the critical section.
Eliminate duplication of the pmap and pv list unlock operations in
pmap_enter() by implementing a single return path. Otherwise, the
duplication will only increase with the upcoming support for psind == 1.
Reviewed by: mmel
Tested by: mmel
Discussed with: kib, markj
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D16443
As discussed in arm@. This is a scaled back version of the prior
commit because xscale is overlaoded in places to mean armv5 or
similar. The OLD XSCALE stuff hasn't been useful in a while. The
original committer (cognet@) was the only one that had boards for
it. He's blessed this removal. Newer XSCALE (GUMSTIX) is for hardware
that's quite old. After discussion on arm@, it was clear there was no
support for keeping it.
Noticed by: andrew@
r336773 removed all things xscale. However, some things xscale are
really armv5. Revert that entirely. A more modest removal will follow.
Noticed by: andrew@
The OLD XSCALE stuff hasn't been useful in a while. The original
committer (cognet@) was the only one that had boards for it. He's
blessed this removal. Newer XSCALE (GUMSTIX) is for hardware that's
quite old. After discussion on arm@, it was clear there was no support
for keeping it.
Differential Review: https://reviews.freebsd.org/D16313
Add std.ralink to define common things across all ralink configs.
Add cpu, machine and options INTRNG to this file.
Remove RT1310.hints file reference: that file isn't in our tree.
This port hasn't been updated since it was committed, apart from
housekeeping. There's no known users, and the known hardware for
this port is too thin to run FreeBSD/arm these days well.
This also removes the last armv4 port. We've had no reports of armv4
systems working since FreeBSD 8. All the kernel support for armv4 has
not been removed since it's too intertwined with armv5 support (which
remains in the tree).
RelNotes: Yes
No objection from: arm@
The last known robust version of this code base was FreeBSD 8.2. There
are no users of this on current, and all users of it have abandoned
this platform or are in legacy mode with a prior version of FreeBSD.
All known users on arm@ approved this removal, and there were no
objections.
Differential Revision: https://reviews.freebsd.org/D16312
Previously, a step by PT_STEP resulted in no signal being raised to
the debugger so that a step was silently completed with the program
continuing to execute after the step. Fix by raising a SIGTRAP
signal with TRAP_TRACE as the signal code.
To simplify the error handling cases (if ptrace_clear_single_step()
fails, etc.) move the handling of PTRACE_BREAKPOINT into the
gdb_trapper() function. If ptrace_clear_single_step() fails,
gdb_trapper() won't claim the fault, and the default case of
SIGILL / ILL_OPC will be used.
Differential Revision: https://reviews.freebsd.org/D16100
Remove all the big-endian arm architectures (ixp425 and ixp435)
support in the kernel and associated drivers.
Differential Revision: https://reviews.freebsd.org/D16257
Xilinx Ultrascale+ are based on Cortex-A53 and use existing
UART driver (uart_dev_cdnc). Enable it in arm64 GENERIC config.
Submitted by: Michal Stanek <mst@semihalf.com>
Obtained from: Semihalf
boot_parse_arg to parse a single arg
boot_parse_cmdline to parse a command line string
boot_parse_args to parse all the args in a vector
boot_howto_to_env Convert howto bits to env vars
boot_env_to_howto Return howto mask mased on what's set in the environment.
All these routines return an int that's the bitmask of the args
translated to RB_* flags. As a special case, the 'S' flag sets the
comconsole_speed env var. Any arg that looks like a=b will set the env
key 'a' to value 'b'. If =b is omitted, 'a' is set to '1'. This
should help us reduce the number of redundant copies of these routines
in the tree. It should also give a more uniform experience between
platforms.
Also, invent a new flag RB_PROBE that's set when 'P' is parsed. On
x86 + BIOS, this means 'probe for the keyboard, and if it's not there
set both RB_MULTIPLE and RB_SERIAL (which means show the output on
both video and serial consoles, but make serial primary). Others it
may be some similar concept of probing, but it's loader dependent
what, exactly, it means.
These routines are suitable for /boot/loader and/or the kernel,
though they may not be suitable for the tightly hand-rolled-for-space
environments like boot2.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D16205
In the armv4/5 world device statements in these files were common, but in
the v6/7 world, other socs don't put device statements into those files, so
this just brings imx5 and imx6 into line with the current conventions.
ignore the timestamp passed in to settime() due to inaccuracy, the core
routines now pass in a nanosecond-accurate time freshly-obtained before
calling each driver's settime() method. Also, add calls to the new
debugging output helpers.
automatically initializing the watchdog using the given value. Also,
attach at BUS_PASS_TIMER to extend watchdog protection to more of the
kernel init process.
The correct value is seconds*2-1. The code was using just seconds*2, which
led to being off by a half-second -- usually not a big deal, except when the
value was the max (128) it overflowed so zero would get written to the
countdown register, which equates to a timeout of a half second.
- Change pcpu zone consumers to use a stride size of PAGE_SIZE.
(defined as UMA_PCPU_ALLOC_SIZE to make future identification easier)
- Allocate page from the correct domain for a given cpu.
- Don't initialize pc_domain to non-zero value if NUMA is not defined
There are some misconceptions surrounding this field. It is the
_VM_ NUMA domain and should only ever correspond to valid domain
values as understood by the VM.
The former slab size of sizeof(struct pcpu) was somewhat arbitrary.
The new value is PAGE_SIZE because that's the smallest granularity
which the VM can allocate a slab for a given domain. If you have
fewer than PAGE_SIZE/8 counters on your system there will be some
memory wasted, but this is obviously something where you want the
cache line to be coming from the correct domain.
Reviewed by: jeff
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D15933
detach() to do nothing if attach() succeeded, which is the opposite of
what's needed. Also, move device_delete_children() from the end to the
beginning of detach(), so that children won't be trying to make use of the
hardware we're in the process of shutting down.
PR: 229510
arrays, as elements 0 and 1 of one array and elements 1 and 2 of the other.
Run the loop 0..1 instead of 1..2 and use named constants to offset into
one of the arrays.
PR: 229508
Add support for the second channel to bcm2835_pwm driver. Configurable
parameters like mode, period, ratio are exposed as sysctls with postfix '2',
e.g.: dev.pwm.N.mode2, dev.pwm.N.period2, dev.pwm.N.ratio2
Second channel can be enabled in DTB by configuring pwn-2chan overlay
instead of pwm in config.txt. See [1]
[1] https://github.com/raspberrypi/firmware/blob/master/boot/overlays/README
Submitted by: Bob Frazier
Differential Revision: https://reviews.freebsd.org/D15769
SDHOST is another SD controller that is present on Raspberry Pi (the
other one is SDHC and handled by bcm2835_sdhci driver). Both
controllers are capable of providing interface to SD card, actual
configuration can be set in dtb file. At the moment custom DTBs for
RPi/RPi2 have sdhost node disabled. On RPi3 sdhost is disabled in
snapshot images by applying mmc.dtbo overlay. To enalbe both devices
user has to edit config.txt on FAT partition and remove or comment
"dtoverlay=mmc" line.
When no overlay applied on RPi3 SDHOST controls SD card and SDHC
interface can be used for SDIO. mmc.dtbo overlay disables SDHOST node
and switches SD card over to SDHC. Likewise sdhost.dtbo overlay (not
currently included in snapshot image, but can be obtained from firmare
repo[1]) disabled SDHC node and switch SD card over to SDHOST.
[1] https://github.com/raspberrypi/firmware/tree/master/boot/overlays
Submitted by: Klaus P. Ohrhallinger <k@7he.at>
Differential Revision: https://reviews.freebsd.org/D14168
and set up the hardware accordingly on each transfer. This replaces the old
configuration done via sysctl, and allows both fdt configuration data and
userland control via the spigen device to work.
Submitted by: Bob Frazier
Differential Revision: https://reviews.freebsd.org/D15031
The test for checking if the clock have a mux was inverted and the mask
to calculate the parent index was wrong was wrong too.
It means that upon creation the incorrect parent was resolved as the current
one and upon reparent the switch was never made.
Pointy hat (lots of them): manu
Using MMCCAM on AllWinner boards is now possible, reaching highest
possible data transfer speed.
For now, MMCCAM doesn't scan cards on boot. This means that scanning
has to be done manually and that it's not possible to mount root FS
from MMC/SD card since there is no block device at the boot time.
For manually scanning the cards, run:
# camcontrol rescan X:0:0
Where X is the bus number (look at camcontrol devlist to determine
bus number assigned to the MMC controller).
Reviewed by: manu
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D15891
Each clock drivers if now fully subclassed, this have the advantage that
we can control the probe order.
Some clocks can have parents from other drivers, for example clocks in the
sun8i_r driver uses clocks from the main clock driver.
This worked before because the sun8i_r node is after the main ccu node in the
dtb and driver are probed in DTB order. This cannot work with the Display
Engine clocks as it is the first node in the DTB.
Tested on: A83T, H5 A64
Tested on: A20 (kevans)
r329104 imported 4.15 DTS which brought CCU to a10/a20. In the process, they
swapped the ordering of 'clocks' for allwinner,sun4i-a10-ahci on both
sun4i-a10 and sun7i-a20 from PLL, Gate to Gate, PLL.
Swap it in the driver.
Note: At this time, this has only been tested on a single board from one of
the supported SoCs. This is enough to boot the board from MMC and have
functional USB- which is still an improvement over where we were at just
before with no functional clocks.
Differential Revision: https://reviews.freebsd.org/D15810
This happens in two cases for a20 clocks:
pll_core for 'n' factor:
factor=0, val=1
factor=n, val=n
ahb divisor:
factor=0,val=/2
factor=n,val=/2^n
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D15806
The timer present in allwinner A64 SoC is unstable, value can jump backward
or forward.
It was found that when bit 11 and upper roll over the low bits can sometimes
being read as all as 1 or all as 0.
Simply ignore the values for those cases.
pmc_process_interrupt takes 5 arguments when only 3 are needed.
cpu is always available in curcpu and inuserspace can always be
derived from the passed trapframe.
While facially a reasonable cleanup this change was motivated
by the need to workaround a compiler bug.
core2_intr(cpu, tf) ->
pmc_process_interrupt(cpu, ring, pmc, tf, inuserspace) ->
pmc_add_sample(cpu, ring, pm, tf, inuserspace)
In the process of optimizing the tail call the tf pointer was getting
clobbered:
(kgdb) up
at /storage/mmacy/devel/freebsd/sys/dev/hwpmc/hwpmc_mod.c:4709
4709 pmc_save_kernel_callchain(ps->ps_pc,
(kgdb) up
1205 error = pmc_process_interrupt(cpu, PMC_HR, pm, tf,
resulting in a crash in pmc_save_kernel_callchain.
- Calculate the number of segments based on the page size
- Add some comments on dma function so it's easier to read
- Only enable interrupts on the last dma segment
- If the segments size is the max transfer size, use the special size 0
for the controller.
- The max_data ivars is in block so calculate it properly.
It was introduced to the tree in r169320 and r169321 in May 2007.
It never got much use and never became a kernel default. The code
duplicates the default path quite a bit, with slight modifications. Just
yank out the cruft. Whatever goals were being aimed for can probably be met
within the existing framework, without a flag day option.
Mostly mechanical change: 'unifdef -m -UINTR_FILTER'.
Reviewed by: mmacy
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D15546
the DMAP region on arm64.
We already have the needed information to build these tables, we just need
to extract it. This significantly simplifies the code.
Obtained from: ABT Systems Ltd
Sponsored by: Turing Robotic Industries
On arm64 we will need to get the phys_avail array from before the kernel
is excluded to create teh DMAP region. In preperation for this pass in the
array length into regions_to_avail.
This will help simplify the arm64 code and allow us to properly exclude
memory that should never be mapped.
Obtained from: ABT Systems Ltd
Sponsored by: Turing Robotic Industries
This reduces the overhead when we have many small mappings, e.g. on some
EFI systems. This is to help use this code on arm64 where we may have a
large number of entries from the EFI firmware.
Obtained from: ABT Systems Ltd
Sponsored by: Turing Robotic Industries
Differential Revision: https://reviews.freebsd.org/D15477
Always disable FIFO access as we don't use it.
Rename some register bits so they are in sync with the register name.
While here add my copyright as I've probably wrote 70% of the code here.
The module uses the mod clock and not the ahb one.
We need to set the mod clock to twice the speed requested as the smallest
divider in the controller is 2.
The clock test function weren't calculating the register value best on the
best div but on the max one.
The cdr2 test function was using the cdr1 formula.
Pointy Hat: manu
This change updates arm, arm64 and mips achitectures. Additionally, it
removes redundant checks for kdb_active where it already results in
kdb_reenter() and adds kdb_reenter() calls where they were missing.
Some architectures check the return value of kdb_trap(), but some don't.
I haven't changed any of that.
Some trap handling routines have a return code. I am not sure if I
provided correct ones for returns after kdb_reenter(). kdb_reenter
should never return unless kdb_jmpbufp is NULL for some reason.
Only compile tested for all affected architectures. There can be bugs
resulting from my poor understanding of architecture specific details.
Reported by: jhb
Reviewed by: jhb, eadler
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D15431
Don't enable regulator on attach but dealt with them on power_up/power_off
Only set the voltage for the signaling regulator since I don't have boards
that can change the supply voltage.
Enable 1.8v signaling voltage.
Only do a reset of the controller at attach and init it at power_up.
We use to enable some interrupts in reset, only enable the interrupts
we are interested in when doing a request.
While here remove the regulators handling in power_on as it is very wrong
and will be dealt with in another commit.
Tested on: A31, A64
With Linux 4.17 dts the compatible for the prcm added 'simplebus' we mean
that the simplebus driver will attach to it at the BUS_PASS_BUS pass.
Change the pass for the prcm driver to be at BUS_PASS_BUS so we will win
the attach.
This introduce a problem as this driver needs the ti_scm one to be already
attached. ti_scm also attach at BUS_PASS_BUS but after the prcm one as it is
after in the dtb and the simplebus driver simpy walk the tree to attach it's
children.
Use the bus_new_pass method to defer the frequencies read at BUS_PASS_TIMER.
This fixes booting on BeagleBone*
Reported by: many
a gpio pin. If neither of the options is specified, pre-set the pin's
output value to the pin's current input value, to achieve glitch-free
transitions to output mode on pins that are pulled up or down at reset
or via fdt pinctrl data.
mode or not. An earlier attempt to make this work was done in r320456, by
always reading the pad status register (PSR) instead of the data register.
But it turns out the values in PSR only reflect the electrical level of an
output pin if the pad is configured with the SION (Set Input On) bit in the
pinmux config, and most output gpio pads are not configured that way.
So now a gpio read is done by returning the value from the data register,
which works right whether the pin is configured for input or output, unless
the pin has been set for OPENDRAIN mode, in which case the PSR is read
instead. For this to work, the pin must also be configured with SION turned
on in the fdt pinmux data, which is a reasonable thing to require for the
unusual case of reading an open-drain output pin.
Include source files and drivers for Marvell ArmadaXP and Armada38X
in GENERIC kernel config.
Submitted by: Michal Mazur <mkm@semihalf.com>
Rafal Kozik <rk@semihalf.com>
Reviewed by: manu
Tested by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Marvell SoC identification function was called by SYSINIT on all armv7
platforms, which brakes platforms other than Marvell built with
GENERIC config. Fix this by shifting SoC identifying to Marvell platform
initialization.
Submitted by: Patryk Duda <pdk@semihalf.com>
Reviewed by: manu
Tested by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
r332839 changed number of cells per interrupt for local_intc from 1 to 2
to pass type of IRQ. Driver expected only 1 cell so after r332839
all interrupt children of local_intc failed to allocate IRQ resource.
Fix this regression by relaxing check for number of cells in interrupt
property to be either 1 or 2.
PR: 227904
Dumpers may wish to print messages from an initialization hook; this
change ensures that such messages aren't mixed with output from the
generic dump code.
MFC after: 1 week
always use 'M. Warner Losh' for consistency.
'All Rights Reserved.' was prescribed by the Buenos Aires Copyright
Convention of 1910, but has been mostly dead since the early 1990's
and completely meaningless since 2000 when Nicaragua ratified the
Berne convention.
Some files not done due to ambiguity of various types.
Move the allwinner early printf support to the snps driver as it
should work with all implementation.
While here add instruction for enabling it on 64bits SoCs.
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
Name each ahci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ahci from kernel; already loaded from kernel
WHile gate_shift was present in the NM_CLK macro it wasn't set into the
clock definition structure resulting in NM clocks not being correctly
gated when they should.
If the module wasn't enabled by the bootloader it will have stayed ungated.
Switch test between zero based factor and power of two one.
This resulted in a miscalculation of the factor if it was a power
of two one.
Some clocks frequencies were not calculated correctly because of that.
This patch adds support for gpio and gpioled into ARMADA38X kernel
config.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14758
This patch replaces in-driver FDT parsing, which was
needed for setting initial values on GPIO pins.
Now FDT is parsed by generic kernel code, pins are set
by invoking gpio_map_gpios method.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14757
This patch implements and exports functions described
in gpio_if.m file. It also uses new gpiobus_attach_bus function
instead of adding gpioc and gpiobus as children. It removes
ulgy reading SoC ID and related if..else, so it depends only on
data read from FDT.
Submitted by: Patryk Duda <pdk@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14756
- Add an implementation of atomic_fcmpset_32() using RAS for armv4/v5.
This fixes recent world breakage due to use of atomic_fcmpset() in
userland.
- While here, be more careful to not expose wrapper macros for 64-bit
atomic_*cmpset to userland for armv4/v5 as only 32-bit cmpset is
implemented.
This has been reviewed, but not runtime-tested, but should fix the arm.arm
and arm.armeb worlds that have been broken for a while.
Reviewed by: imp
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D15147
The return value of atomic_cmpset() and atomic_fcmpset() is an int (which
is really a bool) that has the values 0 or 1. Some of the inlines were
using the type being operated on (e.g. uint32_t) as either the return type
of the function, or the type of a local 'ret' variable used to hold the
return value. Fix all of these to just use plain 'int'. Due to C promotion
rules and the fact that the value can only be 0 or 1, these should all be
harmless.
Reviewed by: imp (only the v4 ones)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D15147
Half of implementations always failed (returned (-1)) and they were
previously used in only one place.
Reviewed by: kib, andrew
Obtained from: CheriBSD
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15102
Also remove the commented out documentation. The documentation arrived
with the import of the copy.9 manpage. I suspect the implementations
came from NetBSD while bootstrapping the Arm and MIPS ports.
Reviewed by: andrew, jmallett
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15108
Switch to standard FDT-base driver behavior and don't attach
if node "status" property value nn DTS is not set to "okay"
On RPi PWM by default is disabled, to enable it pwm.dtbo
from official repo[1] should be copied to overlays directory
on SD card FAT partition and "dtoverlay=pwm" line added to
config.txt. For more details see pwm overlay documentation[2]
sysutils/rpi-firmware port now includes overlays, so they
can be installed as a part of release image build.
[1] https://github.com/raspberrypi/firmware/tree/master/boot
[2] https://github.com/raspberrypi/firmware/blob/master/boot/overlays/README
No objections from: phk@
Linux device tree binding, whose usage is obligatory,
comprises faulty representation of Marvell cryptographic
engine (CESA) - two engines are artificially gathered into
single DT node, in order to avoid certain SW limitation.
This patch improves the cesa driver to support above binding,
depending on compatible string, which helps to ensure
backward compatibility.
Submitted by: Patryk Duda
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14760
Change OF_getencprop_alloc semantics to be combination of malloc and
OF_getencprop and return size of the property, not number of elements
allocated.
For the use cases where number of elements is preferred introduce
OF_getencprop_alloc_multi helper function that copies semantics
of OF_getencprop_alloc prior to this change.
This is to make OF_getencprop_alloc and OF_getencprop_alloc_multi
function signatures consistent with OF_getencprop_alloc and
OF_getencprop_alloc_multi.
Functionality-wise this patch is mostly rename of OF_getencprop_alloc
to OF_getencprop_alloc_multi except two calls in ofw_bus_setup_iinfo
where 1 was used as a block size.
Split out delay parsing into a separate function; we'll support both
{tx,rx}-delay as well as the new versions.
While here, validate that they're within the expected range and fail to
attach if they are not. Assuming that we can clamp the delay is a bad idea
that might result in a non-working awg anyways, so we'll fail early to make
it easier to catch.
This version also unsets the tx and rx delay registers unconditionally and
then sets them if we read a non-zero delay. These delay properties should
default to 0 if not specified, as declared in the binding documentation.
Presumably the delays will be set via hardware configuration if they're not
explicitly set in FDT.
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
On Raspberry Pi platform GPIO controller also responsible for pins
multiplexing. Pi code predates proper FDT support in FreeBSD so a
lot of pinmux info is hardcoded. This patch:
- Implements pinctl methods in bcm2835_gpio
- Converts all devices with ad-hoc pinmux info to proper pin control
mechanisms and adds pinmux info in FreeBSD's custom dts files.
- Adds fdt_pinctrl option to RPI2 and RPI-B kernels
- Adds SPI pinmux config to FreeBSD's customization of GNU DTS.
Reviewed by: imp, manu
Differential Revision: https://reviews.freebsd.org/D14104
If a regulator is missing a mandatory property (like 'regulator-name'), do
not fail, regulator_parse_ofw_stdparam is returning a non-zero value so just
skip this regulator.
Also if any regulator fails to attach continue with the rest of the regulators
instead of returning ENXIO in axp8xx_attach
Tested On: BananaPi M3
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
It was later found that some operation on the OrangePi one will cause
direct accesses to the eeprom to return wrong data again, so reading it all
once via prctl at attach time is no longer sufficient.
This patch moves all global data structures into mv_gpio_softc,
and puts device_t parameter to functions calls everywhere where needed.
As a result, we can create multiple driver instances.
Removed names in function declaration to keep style.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14755
This patch adds support for more than one interrupts
in GPIO controller. It reads necessary information (such as cell size)
from FDT, so there are no magic numbers.
Note that interrupts are still not working, but this patch makes
one good step in correct direction
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14754
This patch introduces gpio debouncing mechanism
with fixed memory allocation in critical section.
When you press button, value at gpio pin connected to button
is changing many times which will cause in unexpected behaviour.
Debouncing mechanism will prevent this phenomenon
Submitted by: Patryk Duda <pdk@semihalf.com>
Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14753
If driver cannot determine ranges based on fdt, it will calculate
them based on number and type of current port.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14752
Ranges in pcie-controller are unused, so could be changed to match Linux
device tree represntation. Same with interrupt-cells and interrupt-parent.
In PCI controller driver ocd_data are used for matching driver and
choose proper resources acquisition function.
fdt_win_process_child have new argument which provide information
about fdt node containing addresses of MMIO registers.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu [DT part]
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14751
In Linux FDT pcie does not have compatible string.
Configuration of windows in mv_common was based on fdt compatible.
Now pcie windows are configured by their parent: pcie_controller.
Processing is moved to fdt_win_process_child. fdt_win_process now
only walk through the tree. SOC_NODE_PCI is position of pcie function in
soc_node_spec array.
PCIe probe cannot use ofw_bus_search_compatible, because it needs to
check also device type and parents compatible.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu [DT part]
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14749
GENERIC ARM config use NEW_PCIB driver (https://wiki.freebsd.org/NEW_PCIB).
To satisfy it, allocation and deallocation of PCI_RES_BUS is necessary.
Conditional compilation is added for backward compatibility with ARMv5
configs.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14748
Define timers registers for both SoCs and choose proper one during runtime
based on information from FDT.
In WDT driver there are different function for ArmadaXP and other ARMv5 SoCs.
In timer driver registers definitions are stored in resource_spec structure
and chosen during runtime.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14746
Define reset registers for both Armada38X and ArmadaXP and
choose proper one during runtime based on information from FDT.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14745
Spliting armv5 and armv7 machdep is necessary for adding Armada38X and
ArmadaXP to GENERIC config.
PLATFORM framework checks SOC type in FDT and will select proper
initialization function implementation during runtime.
Pointers to SoC specific implementation are stored in array of
platform_method_t and provided to framework by FDT_PLATFORM_DEF macro.
PLATFORM framework supports also reset function. To simplify implementation
cpu_reset is moved from mv_common to armv5 and armv7 machdep.
Armada38X and ArmadaXP share now common list of files, so resolve all
dependencies as well.
Submitted by: Rafal Kozik <rk@semihalf.com>
Marcin Wojtas <mw@semihalf.com>
Reviewed by: mw
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14744
Two modules with the same name cannot be loaded, so Marvell specific drivers
cannot have the same name as the generic drivers.
Files with the same name, even in different folders overlaps their .o files,
so in order to prepare for supporting Marvell platforms in GENERIC armv7
config, modify conflicting names.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14743
The PLATFORM code will perform the software loop in the early boot,
so extract the actual delay code to handle situation, when
the timers are already initialized.
Obtained from: Semihalf
Sponsored by: Stormshield
Store pointers to SoC specific functions in mv_timer_config structure
and determine proper config in runtime based on compatible string from FDT.
Compatible string for ArmadaXP timers is changed to match Linux FDT.
Armada 38x uses generic Cortex-A9 timer and separate watchdog drivers, so
it does not need to be supported by timer driver.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14741
In GENERIC kernel choosing proper get_tclk and get_cpu_freq implementation must
be done in runtime. Kernel for both SoC need to have implementation of each
other functions, so common file list mv/files.arm7 is added.
Marvell armv5 SoC have their own non-generic implementation of those function.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14739
Preparation for adding Armada38X and ArmadaXP SoC to GENERIC config.
Supported platform are listed in soc_family enum.
struct decode_win_spec contains platform specific functions and constants.
Function mv_check_soc_family checks SoC type and chooses proper structure
in runtime, as well as platform-dependent functions.
Unnecessary dummy functions are removed.
Because of changing registers name to more generic new definition of
FDT_DEVMAP_MAX in mv_machdep is added.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14738
Validate only drivers used by given platform.
Pointers to validation function
are added to soc_node_spec structure.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14737
get_sar_value is implemented only for ArmadaXP and Armada38X. Splitting it for
two different functions and change registers names result in more generic code.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14736
PCI ports differ between Marvell SoCs, but have the same compatible in FDT.
Identification is made based on parent compatible during attach.
For ArmadaXP skipping enable procedure is necessary. To achieve it
sc_skip_enable_procedure flag is used.
For Armada38x find root procedure is necessary. For other SoCs root link is
always at slot 0. sc_enable_find_root_slot flag is used to select proper
behaviour.
Marvell armv5 platforms does not support msi.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14735
Defining INTRNG remove some necessary registers and declarations of
pic_init_secondary, pic_ipi_send, pic_ipi_read and pic_ipi_clear.
Because Marvell ArmadaXP and Armada38X always use INTRNG, include all
INTRNG code and remove code that does not use it.
Separate pic registers declarations for Armada38X are unnecessary, it
works properly with ArmadaXP config.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14734
The Zynq/Zedboard GPIO driver attempts to tri-state all GPIO pins on
boot up but the order in which I reset the hardware can cause the pins
to be briefly held low before being tri-stated. This is a problem on
boards that use GPIO pins to reset devices.
In particular, the Zybo and ZC-706 boards use a GPIO pin as a USB PHY
reset. If U-boot enables the USB port before booting the kernel, the
GPIO driver attach causes a glitch on the USB PHY reset and the USB
port loses power. My fix is to have the GPIO driver leave the pins in
whatever configuration U-boot placed them.
PR: 225713
Submitted by: Thomas Skibo <thoma555-bsd@yahoo.com>
MFC after: 1 week
DTB Overlays are useful to change/add nodes to a dtb without the need to
modify it.
Add support for building dtbo during buildkernel.
The goal of DTBO present in the FreeBSD source tree is to fill a gap in
time when we submit changes upstream (Linux). Instead of waiting 2 to 4 months
we can add a DTBO in tree in the meantime.
This is not for adding DTBO for capes/hat/addon boards, those will be
better to put in a ports.
This is also not for enabling a i2c/spi/pwm controller on certain pins,
each user have a different use case for those (which pins to use etc ...)
and we cannot have all possible configuration.
Add a dtbo for sun8i-h3-sid which add the SID node missing in upstream dts.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D14782
assym is only to be included by other .s files, and should never
actually be assembled by itself.
Reviewed by: imp, bdrewery (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14180
OF_finddevices returns ((phandle_t)-1) in case of failure. Some code
in existing drivers checked return value to be equal to 0 or
less/equal to 0 which is also wrong because phandle_t is unsigned
type. Most of these checks were for negative cases that were never
triggered so trhere was no impact on functionality.
Reviewed by: nwhitehorn
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14645
Upstream DTBs don't provide IRQ lines for the RNG. Moreover, harvesting
bytes as often as the RNG interrupt is triggered (87 times per sec) is an
overkill.
For these reasons, get rid of the interrupt mode and make callout mode the
default, with random bits harvested every 4 seconds.
Submitted by: Sylvain Garrigues <sylgar@gmail.com>
Reviewed by: ian, imp, manu, mmel
Approved by: emaste
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14541
vbus-supply properties may be specified for each PHY. These properties
reference a regulator that we must turn on/off as we turn the PHY on/off.
However, if the usbphy comes up before the regulator in question (as is the
case with GPIO-controlled regulators), then we will fail to grab a handle to
the regulator and control it as the PHY power state changes.
Fix it by just attaching the usbphy driver later. We don't really need it at
RESOURCE, we just need it to be before DEFAULT when ehci/ohci attach. In
particular, this fixes the USB NIC on a board that we don't yet supported-
without this, it will not power on and if_ure cannot attach.
Tested on: various boards [manu]
Tested on: OrangePi R1 [Rap2 (irc)]
Reported by: Rap2 (irc, "Cannot find USB NIC")
correctly for the data contained on each memory page.
There are several components to this change:
* Add a variable to indicate the start of the R/W portion of the
initial memory.
* Stop detecting NX bit support for each AP. Instead, use the value
from the BSP and, if supported, activate the feature on the other
APs just before loading the correct page table. (Functionally, we
already assume that the BSP and all APs had the same support or
lack of support for the NX bit.)
* Set the RW and NX bits correctly for the kernel text, data, and
BSS (subject to some caveats below).
* Ensure DDB can write to memory when necessary (such as to set a
breakpoint).
* Ensure GDB can write to memory when necessary (such as to set a
breakpoint). For this purpose, add new MD functions gdb_begin_write()
and gdb_end_write() which the GDB support code can call before and
after writing to memory.
This change is not comprehensive:
* It doesn't do anything to protect modules.
* It doesn't do anything for kernel memory allocated after the kernel
starts running.
* In order to avoid excessive memory inefficiency, it may let multiple
types of data share a 2M page, and assigns the most permissions
needed for data on that page.
Reviewed by: jhb, kib
Discussed with: emaste
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14282
Pretty much any other device might need to manipulate a gpio pin during its
probe or attach routines, so these devices must be available as early as
possible.
The gpio device is an interrupt controller, but I didn't choose the
INTERRUPT pass for that reason (it works fine as an interrupt controller as
long as it attaches any time before interrupts are enabled). That just
looked like the right place in the passes to ensure that it attaches before
any type of device that might need gpio pin manipulations.
driver requires interrupts to do transfers, and the drivers for the SPI
devices on the bus quite reasonably expect to be able to do IO while probing
and attaching.
It would have been on an actual named pass before, but none were really
appropriate in name. Move it to the recently created SUPPORTDEV pass, which
perfectly describes it and keeps it in the right order.
Getting regulator is good, enabling them is better.
When the mmc stack decide to change the voltage for IO, don't
change the main vcc of the sd/mmc, only the io vcc.
AXP803 and AXP813/818 are very similar, only two regulators differs.
AXP803 is the companion chip for A64/R18
AXP813 is the companion chip for A83T
AXP818 is the companion chip for H8 (~A83T)
Add support for all regulators found in both of them.
to what other arches (all except riscv and armv4/5) do.
Submitted by: Hyun Hwang <hyun@caffeinated.codes>
Differential Revision: https://reviews.freebsd.org/D14465
(using "boot -d" at the loader propmt or setting boot_ddb in loader.conf).
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D14428
We don't support float in the boot loaders, so don't include
interfaces for float or double in systems headers. In addition, take
the unusual step of spiking double and float to prevent any more
accidental seepage.
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
appears that node names no longer include leading zeroes in the @address
qualifiers, so we have to search for the nodes involved in interrupt fixup
using both flavors of name to be compatible with old and new .dtb files.
(You know you're in a bad place when you're applying a workaround to code
that exists only as a workaround for another problem.)
The FDT variant is called "gicv2m" too, and as both would try to register
on gic, only one of them would succeed, while we want them both in a
GENERIC kernel.
Reviewed by: andrew
significant source of cache line contention from vm_page_alloc(). Use
accessors and vm_page_unwire_noq() so that the mechanism can be easily
changed in the future.
Reviewed by: markj
Discussed with: kib, glebius
Tested by: pho (earlier version)
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14273
Remove most of the Atmel at91 boards. Most of them are no longer
relevant or used by people. Kept ATMEL since it should work on all the
boards that still work (I've not confirmed this, since I don't have
all these boards). Also kept SAM9G20EK, since I have several boards
that it is used on. If I've deleted a kernel in error, please let me
know.
On the OrangePi One at least, emac reset when an ethernet cable is not
plugged in seems to break ethernet. Soft reset will fail, even with
increasing the delay and retries to wait for up to 20 seconds. This can be
reproduced across at least two different OrangePi One's by simply leaving
ethernet cable unplugged when awg attaches. Whether it's plugged in or not
through u-boot process makes no difference.
Skipping the reset in this configuration doesn't seem to cause any problems,
tried across many many reboots with and without ethernet cable plugged in.
Tested on: OrangePi One
Tested on: Other boards (manu)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13974
global to per-domain state. Protect reservations with the free lock
from the domain that they belong to. Refactor to make vm domains more
of a first class object.
Reviewed by: markj, kib, gallatin
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14000
Similarly as we already do for arm64, for mitigation is necessary to
flush branch predictor when we:
- do task switch
- receive prefetch abort on non-userspace address
The user can disable this mitigation by setting 'machdep.disable_bp_hardening'
sysctl variable, or it can check actual system status by reading
'machdep.spectre_v2_safe'
The situation is complicated by fact that:
- for Cortex-A8, the BPIALL instruction is effectively NOP until the IBE bit
in ACTLR is set.
- for Cortex-A15, the BPIALL is always NOP. The branch predictor can be
only flushed by doing ICIALLU with special bit (Enable invalidates of BTB)
set in ACTLR.
Since access to the ACTLR register is locked to secure monitor/firmware on
most boards, they will also need update of firmware / U-boot.
In worst case, when secure monitor is on-chip ROM (e.g. PandaBoard),
the board is unfixable.
MFC after: 2 weeks
Reviewed by: imp, emaste
Differential Revision: https://reviews.freebsd.org/D13931
the "power down" watchdog used by the ROM boot code is still active when the
regular watchdog is activated, turn off the power-down watchdog.
This adds support for the "fsl,ext-reset-output" FDT property. When
present, that property indicates that a chip reset is accomplished by
asserting the WDOG1_B external signal, which is supposed to trigger some
external component such as a PMIC to ready the hardware for reset (for
example, adjusting voltages from idle to full-power levels), and assert the
POR signal to SoC when ready. To guard against misconfiguation leading to a
non-rebootable system, the external reset signal is backstopped by code
that asserts a normal internal chip reset if nothing responds to the
external reset signal within one second.
bottom of the file, where it is in most imx5/6 drivers. Switch from an RD2
macro using bus_space_read_2() to an inline function using bus_read_2();
likewise for WR2. Use RESOURCE_SPEC_END to end the resource_spec list.
Net effect should be no functional changes.
instead of frobbing the registers directly.
As a hack the bcm2835_pwm kmod presently ignores the 'status="disabled"'
in the RPI3 DTB, assuming that if you load the kld you probably
want the PWM to work.
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
functionality on Raspberry Pi 0.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13924
(i386 and arm) that never implement them. This allows the removal of
#ifdef PHYS_TO_DMAP on code otherwise protected by a runtime check on
PMAP_HAS_DMAP. It also fixes the build on ARM and i386 after I forgot an
#ifdef in r328168.
Reported by: Milan Obuch
Pointy hat to: me
kernel by PHYS_TO_DMAP() as previously present on amd64, arm64, riscv, and
powerpc64. This introduces a new MI macro (PMAP_HAS_DMAP) that can be
evaluated at runtime to determine if the architecture has a direct map;
if it does not (or does) unconditionally and PMAP_HAS_DMAP is either 0 or
1, the compiler can remove the conditional logic.
As part of this, implement PHYS_TO_DMAP() on sparc64 and mips64, which had
similar things but spelled differently. 32-bit MIPS has a partial direct-map
that maps poorly to this concept and is unchanged.
Reviewed by: kib
Suggestions from: marius, alc, kib
Runtime tested on: amd64, powerpc64, powerpc, mips64
Focus on code where we are doing multiplications within malloc(9). None of
these ire likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
X-Differential revision: https://reviews.freebsd.org/D13837
- Add a per compatible configuration struct
- Not all SoC uses the same size for DMA transfert, add this into the
configuration data
- Use new timing mode for some SoC (A64 mmc)
- Auto calibrate clock for A64 mmc/emmc
- A64 mmc controller need masking of data0
- Add support for vmmc/vqmmc regulator
- Add more capabilities, r/w speed is better for eMMC
- MMC_CAP_SIGNALING_180 gives weird result so do not enable it for now.
- Add new register documented in H3/A64 user manual
Tested-On: Pine64-LTS (A64), eMMC still doesn't work
Tested-On: A64-Olinuxino (A64), sd and eMMC are working
Tested-On: NanoPi Neo Plus2 (H5), sd and eMMC are working
Tested-On: OrangePi PC2 (H5), sd only (no eMMC)
Tested-On: OrangePi One (H3), sd only (no eMMC)
Tested-On: BananaPi M2 (A31s), sd only (no eMMC)
Attaching syscon_generic earlier than BUS_PASS_DEFAULT makes it more
difficult for specific syscon drivers to attach to the syscon node and to
get ordering right. Further discussion yielded the following set of
decisions:
- Move syscon_generic to BUS_PASS_DEFAULT
- If a platform needs a syscon with different attach order or probe
behavior, it should subclass syscon_generic and match on the SoC specific
compat string
- When we come across a need for a syscon that attaches earlier but only
specifies compatible = "syscon", we should create a syscon_exclusive driver
that provides generic access but probes earlier and only matches if "syscon"
is the only compatible. Such fdt nodes do exist in the wild right now, but
we don't really use them at the moment.
Additionally:
- Any syscon provider that has needs any more complex than a spinlock solely
for syscon access and a single memory resource should subclass syscon
directly rather than attempting to subclass syscon_generic or add complexity
to it. syscon_generic's attach/detach methods may be made public should the
need arise to subclass it with additional attach/detach behavior.
We introduce aw_syscon(4) that just subclasses syscon_generic but probes
earlier to meet our requirements for if_awg and implements #2 above for this
specific situation. It currently only matches a64/a83t/h3 since these are
the only platforms that really need it at the time being.
Discussed with: ian
Reviewed by: manu, andrew, bcr (manpages, content unchanged since review)
Differential Revision: https://reviews.freebsd.org/D13793
allocated with a tag to come from the specified domain if it meets the
other constraints provided by the tag. Automatically create a tag at
the root of each bus specifying the domain local to that bus if
available.
Reviewed by: jhb, kib
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13545
userspace to control NUMA policy administratively and programmatically.
Implement domainset based iterators in the page layer.
Remove the now legacy numa_* syscalls.
Cleanup some header polution created by having seq.h in proc.h.
Reviewed by: markj, kib
Discussed with: alc
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13403
Although these should have been 'emac', upstream DTS is going with using
'gmac' as the function name for the emac RGMII pins. Rename here to
accommodate.
emac support for the a83t should come in with the 4.16 DTS update, in
another couple of months.
For each we need to walk the MADT to find which we have, then add the
driver as needed. As each may have a child they will each walk the same
table to find these details.
Reviewed by: mmel
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8720
This adds a new acpi_bus interface with a map_intr method. This is similar
to the Open Firmware map_intr method and allows us to create the needed
mapping from ACPI space to INTRNG space.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8617
Highlights of the new bindings:
- ahb clock is specified as 'stmmaceth'
- The PHY to be used is now specified as phy-handle
- We must now check the parent of the node phy-handle points to in order to
discover if we're using internal PHY.
- The ephy clk/reset will be specified on the PHY node, not the emac node.
Care has been taken to ensure that we remain compatible with the older
bindings that we were previously using.
Tested on: Pine64 (A64, old bindings)
Tested on: Pine64-LTS (A64, new bindings) [manu]
Tested on: OrangePi-One (H3, internal PHY) [manu]
Tested on: NanoPi M1 Plus (H3, external PHY) [manu]
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13777
The sid controller on the H3 is generally identical in location, size, and
efuse offset to the a64 and the a83t. The main difference is that the H3 has
a silicon bug that sometimes causes the rootkey (at least) to be garbled
unless first read by the prctl registers.
This device is currently not in our DTS and, as of now, is not yet present
in mainline Linux DTS.
Tested on: OrangePi One
Technically supported on the later SoCs, this will only really be used to
add support for the H3 sid. The H3 has a silicon bug that manifests itself
by returning garbled rootkeys unless first read via the prctl registers.
The emac bindings that are landing in Linux 4.15 specify a syscon property
on the emac node that point to /soc/syscon. Use this property if it's
specified, but maintain backwards compatibility with the old method.
The older method is still used for boards that we get .dtb from u-boot, such
as pine64, that did not yet have stable emac bindings.
Tested on: Banana Pi-M3 (a83t)
Tested on: Pine64 (a64)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13296
Newer Allwinner SoCs have nearly identical SID controllers with efuse space
starting at 0x200 into their register space and thermal data available at
0x234, making all of these fairly trivial additions.
The h3 will be added at a later time after some testing, due to a silicon
bug that causes the rootkey (at least) to be read incorrectly unless first
read via the control register.
Fully subclass the dwmmc driver and split every driver into multiple files.
There is still a few quirks in the dwmmc driver that will need some work.
Tested On: Pine64 Rock64
Differential Revision: https://reviews.freebsd.org/D13615
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
phy-mode can be one of: rgmii, rgmii-id, rgmii-txid, rgmii-rxid; as this was
written, any of these alternate -id configurations would break as we fail to
configure syscon for rgmii. Instead, simply check that phy-mode is
configured for rgmii and we'll let the PHY driver handle any internal delay
configuration.
The pine64 should eventually specify phy-mode = "rgmii-txid" to address
gigabit issues when rx delay is configured, motivating this change.
kernel VA mapping in the temporary page tables set up by locore-v6.S.
The number used to be hard-coded to 64MB, which is still the default if
the kernel option is not specified. However, 64MB is insufficient for
using a large mdroot filesystem. The hard-coded number can't be safely
increased because too large a number may run into memory-mapped IO space
on some SoCs that must not be mapped as ordinary memory.
platform divergence.
Only architectures which pass arguments in registers (mips)
and platforms which use really weird compilers (any?) would
need to augment the contents of <sys/_stdarg.h>
Convert x86, arm and arm64 architectures to use <sys/_stdarg.h>
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
The real kernel page tables are set up much earlier in initarm() now than
they were when early printf support was first added, and they end up undoing
the mapping made in locore.S for early printf support. This re-adds the
mapping after switching to the new/real kernel page tables, making early
printf work again right after switching to them.
They provide relaxed-ordered atomic access semantic. Due to the
FreeBSD memory model, the operations are syntaxical wrappers around
the volatile accesses. The volatile qualifier is used to ensure that
the access not optimized out and in turn depends on the volatile
semantic as implemented by supported compilers.
The motivation for adding the operation is to help people coming from
other systems or knowing the C11/C++ standards where atomics have
special type and require use of the special access operations. It is
still the case that FreeBSD requires plain load and stores of aligned
integer types to be atomic.
Suggested by: jhb
Reviewed by: alc, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D13534
A comment in bcm_bsc_fill_tx_fifo() even lists sc_totlen > 0 as a
precondition for calling the routine. I apparently forgot to make the
code do what my comment said.
This variable should be pure MI except possibly for reading it in MD
dump routines. Its initialization was pure MD in 4.4BSD, but FreeBSD
changed this in r36441 in 1998. There were many imperfections in
r36441. This commit fixes only a small one, to simplify fixing the
others 1 arch at a time. (r47678 added support for
special/early/multiple message buffer initialization which I want in
a more general form, but this was too fragile to use because hacking
on the msgbufp global corrupted it, and was only used for 5 hours in
-current...)
Rather than relying on 'cluster' existing in the context they're used in,
use the argument name.
Differential Revision: https://reviews.freebsd.org/D12931
This fixes some regulator issues with a83t/BananaPi-M3; the pin value was
getting clobbered as we reconfigured the pin when initializing the
regulator.
Discussed with: ian
Recent DTS (from Linux 4.14) specify a compatible "allwinner,sun50i-h5-ccu"
for H5 SoC. Since we get the DTB from u-boot this wasn't noticed.
Add the compatible so later version of u-boot will not fail for us.
a10_gpio previously accepted only {allwinner,}drive and {allwinner,}pull for
drive/bias setting, while newer DTS is using drive-strength and
bias-{disable,pull-up,pull-down} properties. Accept these properties as
well.
Additionally make bias and drive strength optional rather than required; not
setting them should just indicate that we do not need to configure these
properties.
Tested on: BananaPi-M3 (a83t)
Reviewed by: manu
Approved by: emaste (implicit)
Obtained from: NetBSD (partially)
Differential Revision: https://reviews.freebsd.org/D13284
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
For FreeBSD/arm64's cloudabi32 support, I'm going to need a TO_PTR() in
this place. Also use it for all of the other source files, so that the
difference remains as minimal as possible.
MFC after: 2 weeks
Originally a patch by Mark Millard, augmented with information from work
done on NetBSD by jmcneill@.
Submitted by: Mark Millard (markmi@dsl-only.net)
Reviewed by: emaste, manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13240
The r-ccu on the a83t differs from the others only by what it names the
ar100 parents. Export the _CCU macros (now converted to an enu) so that
ccu_sun8i_r can differentiate between a83t r-ccu and the others, then add
the compat string for the a83t r-ccu.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13206
plain-vanilla ETH microcode. The QOS_VLAN firmware added support in microcode
for handling IEEE 802.1q tags, but the npe(4) driver did not actually
support the relevant signalling. As a result, it was impossible to use
VLANs with npe(4). Switching to the more basic microcode (same license)
removes the on-NIC promisisng and makes vlan(4) work on both NPE interfaces.
Ref: https://lists.freebsd.org/pipermail/freebsd-arm/2012-August/003826.html
Upon successful completion, the execve() system call invokes
exec_setregs() to initialize the registers of the initial thread of the
newly executed process. What is weird is that when execve() returns, it
still goes through the normal system call return path, clobbering the
registers with the system call's return value (td->td_retval).
Though this doesn't seem to be problematic for x86 most of the times (as
the value of eax/rax doesn't matter upon startup), this can be pretty
frustrating for architectures where function argument and return
registers overlap (e.g., ARM). On these systems, exec_setregs() also
needs to initialize td_retval.
Even worse are architectures where cpu_set_syscall_retval() sets
registers to values not derived from td_retval. On these architectures,
there is no way cpu_set_syscall_retval() can set registers to the way it
wants them to be upon the start of execution.
To get rid of this madness, let sys_execve() return EJUSTRETURN. This
will cause cpu_set_syscall_retval() to leave registers intact. This
makes process execution easier to understand. It also eliminates the
difference between execution of the initial process and successive ones.
The initial call to sys_execve() is not performed through a system call
context.
Reviewed by: kib, jhibbits
Differential Revision: https://reviews.freebsd.org/D13180
A ccu driver was added for the a83t in r326114. Add compat string to
aw_ccung and register the clocks for the a83t upon attach.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13205
This value may be set by userspace so we need to check it before using it.
If this is not done correctly on exception return the kernel may continue
in kernel mode with all registers set to a userspace controlled value. Fix
this by moving the check into set_mcontext, and also add the missing
sanitisation from the arm64 set_regs.
Discussed with: security-officer@
MFC after: 3 days
Sponsored by: DARPA, AFRL
Upstream DTS has switched to using CCU rather than /clocks nodes. Add a CCU
driver for the a83t to bring us closer to upstream, but don't yet attach it
to ccu node.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12843
Add a means to specify mask/value for the prediv condition instead of
shift/width/value for clocks that have a more complex mux scenario.
Specifically, ahb1 on the a83t has the prediv applied if mux is either b10
or b11.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12851
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
We currently support the a83t's r_intc in a somewhat hack-ish way; our .dts
describes it as nmi_intc, and uses a subset of the actual register space to
make it line up with a20/a31 nmi offsets.
This breaks with the recent 4.14 update describing r_intc using the full
register space, so update aw_nmi to use the correct register offsets with
the right compat data in a way that doesn't break our current dts with
nmi_intc or upstream with r_intc described.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13122
Stale packets should not be transmitted when the interface comes up after being down.
Count the successfully transmitted ones for statistics and drop the rest.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12539
Use a spare dma map when attempting to map a new mbuf on the rx path.
If the mbuf allocation fails or the dma map loading for the new mbuf fails just reuse the old mbuf
and increase the drop counter.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12538
- use awg_encap and awg_txeof names to match iflib and other network drivers.
- handle m_collapse failure similarly by freeing the mbuf rather than reenqueuing it where it will continue to fail.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13035